2AK6P-NVR1008MBNVR

Statement Thank you for purchasing our product! This quick user guide will talk about main usages of the product.More information can be found on our website and the help center. This user guide may contain inaccurate content due to hardware and software upgrade.It is subject to change without previous notice. Safety Caution Please do not put any fluid container on the product. Please use the product in ventilated environment and prevent blocking the vents. Please use included power supply with the product to prevent damage to the product. Please use the product under its standard working temperature and humidity. (advised in this manual or distributor’s website) Dust on PCB may cause short circuit.It is suggested to clean the dust on PCB timely to make the product work properly. Please obey the regulation and policy in your country and area during the installation of this. NVR IPC Wireless Mini NVR kit manual       < Antenna port:Dual antennas expand the WIFI range; WAN port: Connect the NVR to the Internet; TF card slot: TF card interface; HDMI interface: Connect to high-definition TV; USB port: Connect mouse and U disk;        Power supply: DC power input (12V 2A); RESET: Press and hold for 3 seconds to reset (clear the password, network and other settings, do not clear the camera channel, release the button and restart to take effect), continue to press the reset button for 10 seconds to reset all (clear the password, including all settings such as camera channels and so on); Connect the system as shown in the steps below System wiring diagram System connection and installation Open the hard disk cover on the back of the chassis and remove the cover. Align the hard disk socket with the wiring port on the NVR, insert the hard disk, and pay attention to the direction of the hard disk. Use TM3*6 silver screws to lock the silver disk to the hard disk cover Use KM2*6 silver screws to lock the hard drive cover to the rear case. Insert one end of the HDMI cable into the HDMI port of the NVR rear panel, and the other end into the HDMI port of the TV or monitor; Insert the USB mouse into the USB port on the NVR rear panel; Connect one end of the network cable to the WAN network interface of the NVR rear panel, and the other end to the home router or network access point; Connect the power adapter connector to the power socket on the NVR rear panel, and then insert the adapter into the surge protector or uninterruptible power supply (UPS); make sure that the surge protector or uninterruptible power supply (UPS) switch is ON, After a few moments, the NVR splash screen will appear on the screen; Press and hold the power button of the camera for 2 seconds to turn it on.          Hard disk installation Configure WNVR on TV or Monitor After powering on, please follow the steps of the setup wizard to complete the settings of language, network, time, view real-time screen, password, hard disk and download APP and device. If you see the prompt "Network status is good!" in the network setup wizard interface, it means your recorder has successfully connected to the Internet. (Tips: If there is no Internet near your video recorder device, you can also choose to use it without connecting to the Internet. This method will make it impossible to use the mobile APP to watch the video from a long distance.) Menu bar Right-click and you'll go to the main menu, right-click again to exit the menu or go back. Split screen selection: Change the view state, you can choose to view multiple or single cameras. Video playback: Enter the video playback interface to play the recorded video. Camera Settings: View the settings related to the added camera. System Settings: Manage all system settings. Channel Sort: Adjust the camera channel sorting order. Device Diagnosis: Diagnose camera status, signal and firmware version. Network Settings: View your device's network connection. Exit the system: logout, restart, shutdown functions. System Settings Channel Toolbar Right click on the mouse select System Settings: You can modify system -related settings. General settings: Set language, display resolution, audio volume and view firmware information. Camera settings: All camera settings, alarm settings, recording settings. Date/Time: Set device time, date and time zone information. Network settings: Network connection to router settings, wireless channel settings. Device Diagnosis: Device and added camera status detection and diagnosis. Storage settings: View hard disk or TFcard information and format. Move the left mouse button to the corresponding channel, and the toolbar at the bottom of the pop-up channel will be activated. Click the corresponding icon to enable the corresponding function settings. From left to right: Audio output switch button, camera light control and color adjustment button, PTZ control button, talkback button, channel full-screen playback button. 3 Recording settings Right click on the mouse ĺ select camera settings ĺ select recording mode on the right side of the interface Camera working mode The battery camera includes three modes: Best power saving, best video recording, and always video recording; The constant power camera includes two modes: constant recording and event recording; the specific mode function introduction is entered into the setting interface for detailed viewing, and the corresponding working mode is selected according to the usage scene of your device. Smart detection settings Right click on the mouse button ĺ select camera settings ĺ enable smart detection on the right side of the interface, click smart detection settings. You can set the camera's detection area, sensitivity level, detection type (humanoid), humanoid frame switch and other functions; Smart detection period setting Right -click on the mouse ĺ select camera settings ĺ detect time period settings on the right side of the interface. During the set time period, the device will detect the motion …

Text truncated - open the document above for the full version.

Agent Authorization Company: Shenzhen DC Times Technology Co., Ltd Address: Floor 3, Building J, Jinchangda Industrial Zone, Shangwei Village, Zhangkengjing, Guanlan Town, Longhua New District, Shenzhen, China Product Name: NVR Model Number(s): NVR-1008M-b, NVR-6410NM-WU, NVR-6810NM-WU, NVR- 6114NM-W-MU, NVR-6118NM-W-MU, NVR-6124NM-W-2MU, NVR-6128NM-W-2MU, NVR-8124NM-W-2MU, NVR-8128NM-W-2MU, NVR-8154NM-W-2MU, NVR-8158NM- W-2MU, POE-6810NM, POE-8128NM Product Description: NVR We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Oct. 08, 2022 Name: TONY LEE Title: General Manager Company: Shenzhen DC Times Technology Co., Ltd

Shenzhen DC Times Technology Co., Ltd Floor 3, Building J, Jinchangda Industrial Zone, Shangwei Village, Zhangkengjing, Guanlan Town, Longhua New District, Shenzhen, China Oct. 08, 2022 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: 2AK6P-NVR1008MB Models: NVR-1008M-b, NVR-6410NM-WU, NVR-6810NM-WU, NVR- 6114NM-W-MU, NVR-6118NM-W-MU, NVR-6124NM-W-2MU, NVR- 6128NM-W-2MU, NVR-8124NM-W-2MU, NVR-8128NM-W-2MU, NVR-8154NM-W-2MU, NVR-8158NM-W-2MU, POE-6810NM, POE- 8128NM To Whom It May Concern: We, The Shenzhen DC Times Technology Co., Ltd hereby declare that all the series model are the same as the test model except for the model names. Except for the different above, no other modification is performed. Sincerely, Shenzhen DC Times Technology Co., Ltd Signature: [TONY LEE, General Manager]

Report No.: AGC10648220601AP03 Page 1 of 3 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC10648220601AP03 Page 2 of 3 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC10648220601AP03 Page 3 of 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report****************************************

FCC ID Label Location 20mm*20mm FCC ID: 2AK6P-NVR1008MB

Label and Label Location The Label’s material is silk-screen, it cannot be easily erased. The size for the label is 60mm*20mm The MIC Logo height is 3mm*3mm. The Printing Color is White and Black. NVR Model: NVR-1008M-b XXX-XXXXXX Series Model: NVR-6410NM-WU, NVR-6810NM-WU, NVR-6114NM-W-MU, NVR-6118NM-W-MU, NVR-6124NM-W-2MU, NVR-6128NM-W-2MU, NVR-8124NM-W-2MU, NVR-8128NM-W-2MU, NVR-8154NM-W-2MU, NVR-8158NM-W-2MU, POE-6810NM, POE-8128NM

Report No.: AGC10648220601AP03 Page 1 of 8 INTERNAL PHOTOS PORT VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 1) Report No.: AGC10648220601AP03 Page 2 of 8 OPEN VIEW OF EUT (FIGURE 2) ANTENNA CLOSE-UP PHOTO-1 Antenna 1 Antenna 2 Antenna 3 Report No.: AGC10648220601AP03 Page 3 of 8 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC10648220601AP03 Page 4 of 8 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) Report No.: AGC10648220601AP03 Page 5 of 8 INTERNAL VIEW OF EUT (FIGURE 5) INTERNAL VIEW OF EUT (FIGURE 6) Report No.: AGC10648220601AP03 Page 6 of 8 INTERNAL VIEW OF EUT (FIGURE 7) INTERNAL VIEW OF EUT (FIGURE 8) Report No.: AGC10648220601AP03 Page 7 of 8 INTERNAL VIEW OF EUT (FIGURE 9) INTERNAL VIEW OF EUT (FIGURE 10) Report No.: AGC10648220601AP03 Page 8 of 8 INTERNAL VIEW OF EUT (FIGURE 11) INTERNAL VIEW OF EUT (FIGURE 12) ****************************************End of Report****************************************

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description NVR Test Model NVR-1008M-b Series Model NVR-6410NM-WU, NVR-6810NM-WU, NVR-6114NM-W-MU, NVR-6118NM-W-MU, NVR-6124NM-W-2MU, NVR-6128NM-W-2MU, NVR-8124NM-W-2MU, NVR-8128NM-W-2MU, NVR-8154NM-W-2MU, NVR-8158NM-W-2MU, POE-6810NM, POE-8128NM FCC ID 2AK6P-NVR1008MB 2. EVALUATION METHOD AND LIMIT Human exposure to RF emissions from mobile devices (47 CFR §2.1091) may be evaluated based on the MPE limits adopted by the FCC for electric and magnetic field strength and/or power density, as appropriate, since exposures are assumed to occur at distances of 20 cm or more from persons. LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE Frequency Range (MHz) E-field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Time |E| 2 , |H| 2 or S (Minutes) 0.3 -- 1.34 614 1.63 (100)* 30 1.34 -- 30 824/f 2.19/f (180/f 2 )* 30 30 -- 300 27.5 0.073 0.2 30 300 -- 1500 -- -- f/1500 30 1500 -- 100,000 -- -- 1.0 30 *Note: 1. f= Frequency in MHz * Plane-wave Equivalent Power Density 2. The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.1091 and 2.1093 on source-based time-averaging requirement for mobile and portable transmitters. S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna CALCULATION A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. The distance must be at least 20 cm and fully supported by the operating and installation configurations of the transmitter and its antenna(s), according to the source-based time-averaged maximum power requirements of § 2.1091(d)(2). In cases where cable losses or other attenuations are applied to determine compliance, the most conservative operating configurations and exposure conditions must be evaluated. Antenna 1 Gain=4.95dBi (Numeric 3.13), π=3.14 Antenna 2 Gain=4.57dBi (Numeric 2.86), π=3.14 Antenna 3 Gain=5.18dBi (Numeric 3.30), π=3.14 Note: 1. Only the worst case recorded. 2. The 2.4G WIFI ANT1+ ANT2 and 2.4G WIFI ANT3 band can transmit simultaneously: 0.0140/1+0.0097/1=0.0237＜1 Frequency Output Power Output Power Power Density Power Density Limit MHz dBm mW mW/cm 2 mW/cm 2 2412 (ANT1) 10.97 12.50 0.0078 1 2412 (ANT2) 10.95 12.45 0.0071 1 2412 (ANT1+2) 13.52 22.49 0.0140 1 2412 (ANT3) 11.69 14.76 0.0097 1

Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 1 / 10 APPROVAL SHEET CUSTOMER NAME: PRODUCT NAME: 2.4G FPC L=180mm+端子terminal CUSTOMER P/N: YoubiP/N: UB01C180F3D1368AREV: A MANUFACTURER SIGNATURE CUSTOMER SIGNATURE CHECKED BY: Eddy APPROVED BY:Changxing.Liu DATE:2022/10/7 Antenna Type：PIFA antenna DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 2 /10 ModificationHistory VersionContentRevisionIssuedbyDate AOriginalversionEddy2022-10-7 DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 3 /10 Content ltemDescription 1.-------------------------------------------------------------------ElectricalSpecification 2.---------------------------------------------------------------TestItemsandEquipment 3.---------------------------------------------------------------------------------SParameter 4.------------------------------------------------------------------------EfficiencyandGain 5.---------------------------------------------------------------------------RadiationPattern 6.------------------------------------------------------------------------------Activetestdata 7.-------------------------------------------------------------Antennainstallationdiagram 8.-----------------------------------------------------------------MechanicalSpecification 9.------------------------------------------------------------------------------------Packaging Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 4 / 10 1. Electrical Specification: 2.Test Items and Equipment CharacteristicsSpecificationsUnit Outline Dimensions40x18.5,L180mm Frequency 2400-2500 MHz Impedance50Ω VSWR< 1.92 PolarizationLinear Polarization Gain 5.18 dBi Efficiency>50 % Connector TypeMHF-1-Plug Operating temperature-20°C~+85°C Storage Temp-20°C~+50°C Test itemsTest equipment S Parameter 1.Return Loss 2.VSWR Network analyzer (Agilent E5071B) The whole machine of Passive parameters 1.Frequency 2.Gain 3.Radiation Pattern 1.3D microwave darkroom (5m*5m*5m) 2.Network analyzer (Agilent E5071B) The whole machine of Active parameters 1.TRP 2.TIS 1.3D microwave darkroom (5m*5m*5m) 2.Comprehensive test instrument (CMW500) Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 5 / 10 3.S Parameter * Voltage Standing Wave Ratio(VSWR) Return Loss(RL) R L=20*log10[ (VSWR+1)/(VSWR-1) 4. Efficiency and Gain Frequency (MHz) Return Loss(dB) VSWR 2400-16.111.37 2450-15.931.37 2500-12.901.58 Frequency (MHz) 240024502500 Efficiency (%) 65.368.766.2 Gain (dBi) 4.83 5.185.13 DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 6 /10 5.RadiationPattern 5-1Antenna3DRadiationPattern 2400MHz 2450MHZ 2500MHZ DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 7 /10 5-2Antenna2DRadiationPattern Phi0 Phi90 Theta90 DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 8 /10 6.Antennainstallationdiagram Antenna Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 9 / 10 7.Mechanical Specification

Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 1 / 11 承 认 书 APPROVAL SHEET 客 户 名 称 CUSTOMER NAME: 产 品 名 称 PRODUCT NAME: 青干剑白色天线L=260mm+端子 White antenna L=260mm+ terminal 客 户 料 号 CUSTOMER P/N: 优比电子料号 YoubiP/N:UB02C120W5D37a6AREV: A MANUFACTURER SIGNATURE CUSTOMER SIGNATURE CHECKED BY: King APPROVED BY:Changxing.Liu DATE:2022/08/10 Antenna type： Dipole Antenna DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 2 /11 ModificationHistory VersionContentRevisionIssuedbyDate AOriginalversionKing2022-08-10 DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 3 /11 Content ltemDescription 1.--------------------------------------------------------------------ElectricalSpecification 2.---------------------------------------------------------------TestItemsandEquipment 3.---------------------------------------------------------------------------------SParameter 4.------------------------------------------------------------------------EfficiencyandGain 5.---------------------------------------------------------------------------RadiationPattern 6.-----------------------------------------------------------------MechanicalSpecification Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 4 / 11 1. Electrical Specification: 2.Test Items and Equipment CharacteristicsSpecificationsUnit Outline Dimensions13x182,L120mm Frequency 2400-2500 MHz Impedance50Ω VSWR< 2.0 PolarizationLinear Polarization Gain 4.95REF dBi Efficiency>70 % Connector Type1.13 MHF-1-Plug Operating temperature-20°C~+65°C Storage Temp-20°C~+50°C Test itemsTest equipment S Parameter 1.Return Loss 2.VSWR Network analyzer (Agilent E5071B) The whole machine of Passive parameters 1.Frequency 2.Gain 3.Radiation Pattern 1.3D microwave darkroom (5m*5m*5m) 2.Network analyzer (Agilent E5071B) The whole machine of Active parameters 1.TRP 2.TIS 1.3D microwave darkroom (5m*5m*5m) 2.Comprehensive test instrument (CMW500) DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 5 /11 3.SParameter *VoltageStandingWaveRatio(VSWR) ReturnLoss(RL) RL=20*log10[(VSWR+1)/(VSWR-1) 4.EfficiencyandGain Frequency (MHz) 240024502500 Efficiency (%) 73.4576.3875.34 Gain (dBi) 4.864.954.79 Frequency (MHz) ReturnLoss (dB) VSWR 2400-30.41.06 2450-191.25 2500-15.61.39 DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 6 /11 5.RadiationPattern 5-1Antenna3DRadiationPattern X Z DongguanYoubiElectronicsCo.,LTDHangzhouYoubigeElectronicsCo.,LTDShenzhenYoubiElectronicsCo.,LTD Room101,Building2,No.9,Room106,Building3,LetongSciencePark,Room106,BuildingA,XinzhengIndustrialPark, XinfaRoad,LinVillage,TangxiaTownNo.500QiuyiRoad,BinjiangDistrict57LiuxianRoad,Bao'anDistrict,Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 7 /11 5-2Antenna2DRadiationPattern Phi02D Phi902D Theta902D Vertical Plane Horizontal Plane Dongguan Youbi Electronics Co.,LTDHangzhou Youbige Electronics Co.,LTDShenzhen Youbi Electronics Co.,LTD Room 101,Building 2,No.9,Room 106,Building 3,Letong Science Park, Room 106, Building A,Xinzheng Industrial Park, Xinfa Road,Lin Village,Tangxia TownNo.500 Qiuyi Road,Binjiang District57 Liuxian Road, Bao 'an District, Shenzhen Tel:+86-769-81777126Website：www.ubuant.com 8 / 11 6. Mechanical Specification: 1. The carton must be labeled 1 PCS/ROHS environmental protection to the carton 2 . carton must be 1 PCS carton label to the left upper corner of the carton.(note: if the tag client requirements are posted in accordance with the customer's requirements;Or else the optimal than tag) 2, PE bag should be labeled LPCS inside box to PE bag.

Page 1 of 130 Report No.: AGC10648220601FE05 FCC ID : 2AK6P-NVR1008MB APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : NVR BRAND NAME : N/A MODEL NAME : NVR-1008M-b, NVR-6410NM-WU, NVR-6810NM-WU, NVR-6114NM-W-MU, NVR-6118NM-W-MU, NVR-6124NM-W-2MU, NVR-6128NM-W-2MU, NVR-8124NM-W-2MU, NVR-8128NM-W-2MU, NVR-8154NM-W-2MU, NVR-8158NM-W-2MU, POE-6810NM, POE-8128NM APPLICANT : Shenzhen DC Times Technology Co., Ltd DATE OF ISSUE : Sep. 29, 2022 STANDARD(S) TEST PROCEDURE(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd FCC Test Report Report No.: AGC10648220601FE05 Page 2 of 130 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Sep. 29, 2022 Valid Initial Release Report No.: AGC10648220601FE05 Page 3 of 130 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 7 2.3. IEEE 802.11N MODULATION SCHEME .................................................................................................... 8 2.4. RELATED SUBMITTAL(S) / GRANT (S) .................................................................................................... 8 2.5. TEST METHODOLOGY ............................................................................................................................. 8 2.6. SPECIAL ACCESSORIES ......................................................................................................................... 8 2.7. EQUIPMENT MODIFICATIONS ................................................................................................................. 8 2.8. ANTENNA REQUIREMENT....................................................................................................................... 9 3. MEASUREMENT UNCERTAINTY ................................................................................................................. 10 4. DESCRIPTION OF TEST MODES ................................................................................................................. 11 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 12 5.1. CONFIGURATION OF EUT SYSTEM ...................................................................................................... 12 5.2. EQUIPMENT USED IN EUT SYSTEM ..................................................................................................... 12 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 12 6. TEST FACILITY .............................................................................................................................................. 13 7. OUTPUT POWER ........................................................................................................................................... 14 7.1. MEASUREMENT PROCEDURE ............................................................................................................. 14 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 14 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 15 8. BANDWIDTH .................................................................................................................................................. 17 8.1. MEASUREMENT PROCEDURE ............................................................................................................. 17 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 17 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 18 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 43 9.1. MEASUREMENT PROCEDURE ............................................................................................................. 43 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 43 9.3. MEASUREMENT EQUIPMENT USEDJN ................................................................................................ 43 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 43 Report No.: AGC10648220601FE05 Page 4 of 130 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 72 10.1 MEASUREMENT PROCEDURE ............................................................................................................ 72 10.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................... 72 10.3 MEASUREMENT EQUIPMENT USED ................................................................................................... 72 10.4 LIMITS AND MEASUREMENT RESULT ................................................................................................. 72 11. RADIATED EMISSION ................................................................................................................................. 86 11.1. MEASUREMENT PROCEDURE......................................…

Text truncated - open the document above for the full version.

Report No.: AGC10648220601FE05 Page 54 of 130 Test_Graph_802.11n40_ANT1_2437_MCS0_Lower Band Emissions Test_Graph_802.11n40_ANT1_2437_MCS0_Higher Band Emissions Report No.: AGC10648220601FE05 Page 55 of 130 Test_Graph_802.11n40_ANT1_2452_MCS0_Lower Band Emissions Test_Graph_802.11n40_ANT1_2452_MCS0_Higher Band Emissions Report No.: AGC10648220601FE05 Page 56 of 130 Test Graphs of Band Edge Emissions in Non-Restricted Frequency Bands-Antenna 1 Test_Graph_802.11b_ANT1_2412_1Mbps_Lower Band Edge Emissions Test_Graph_802.11g_ANT1_2412_6Mbps_Lower Band Edge Emissions Report No.: AGC1…

Text truncated - open the document above for the full version.