2AKCIYJ2020C49MHZToy RC DIY Trike

Reverse Forward Left Right Wheel Alignment Wheel Alignment Dial Turn the wheel alignment tab to the right if your trike drifts to the left. Turn the tab to the left if your trike tends to drift to the right. BUILDING YOUR REMOTE CONTROLOPERATING INSTRUCTIONS A B C D E FG I J K 3 1 2 425 L PO Q N M X 6 1 X 2 X 1 X 1 X 2 X 2 X 4 H DIY RC RACE TRIKE 6 + AGES • For indoor use only. Avoid water when operating. • Do not submerge car or controller in water. • Do not use people or animals as obstacles. • Do not run car into furniture objects or hard surfaces as this will cause damage to both the objects and car. • Keep fingers, hair and loose clothing away from the tires, gears and motor while car is switched to “ON’. • Do not leave car or transmitter near sources of heat or under direct sunlight for long periods of time. • Remove all batteries when not in use to avoid accidental operation. • Adult supervision is recommended when operating car. • Thoroughly inspect products before every use. If the product appears worn, frayed/splintered, cracked, or broken in any manner, discontinue use and discard immediately. SAFETY WARNINGS: PLEASE READ BEFORE USE WARNING: CHOKING HAZARD - Small Parts. Not for Children under 3 years. BATTERY INSTALLATION The chassis requires 4 “AA” 1.5V batteries (not included) and the remote requires one 9V battery (not included). Use a Phillips head screwdriver to loosen the screw securing the corresponding battery cover plate. Insert the batterie(s), ensuring the correct polarity per the diagrams. Replace the battery cover and tighten the screw. • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. • Alkaline batteries are recommended. Use only the specified voltage. • Insert batteries using the correct polarity. Always use, replace, and recharge (if applicable) batteries under adult supervision. • Do not charge with non-rechargable batteries. • Do not short-circuit the battery supply terminals. • Do not dispose of batteries in fire, batteries may explode or leak. • Remove batteries before storing. • Recycle or dispose of batteries according to federal, state, and local laws. • Keep this package for future reference. BATTERY WARNING: INTRODUCTION Congratulations on your purchase of the DIY RC Race Trike Kit. Please read all instructions and warnings on this sheet prior to using the product. Keep this instruction sheet as it contains important information for future reference. CONTENTS Parts to Assemble Your Remote Control A. 1 x Front Body B. 1 x Rear Body C. 1 x Antenna D. 1 x Circuit Board E. 1 x On/Off Switch F. 2 x Joysticks G. 1 x Battery Cover with Screw H. 1 x Connect Remote PCB and Antenna 1. 6 x Short Cross Screws ( 2.3 x 6 PB ) 2. 1 x Cross Screw ( 2.3 x 6 PWB x 6 ) Parts to Assemble Your Race Trike I. 1 x Shell Body J. 1 x Chassis K. 2 x Front Tires L. 2 x Shocks M. 1 x Rear Axle with Rear Tire N. 1 x Rear Axle O. 1 x Circuit Board P. 1 x Top Decorative Bar Q. 1 x Battery Cover with Screw 1. 2 x Short Cross Screws ( 2.3 x 6 PB ) 2. 4 x Cross Screws ( 2.3 x 6 PWB x 6 ) 3. 2 x Long Cross Screws ( 2.3 x 8 PB ) 4. 1 x Cross Screw ( 12.6 x 12 PWB x 8 ) 5. 2 x Cross Screws ( 2.3 x 8 PWB x 8 ) Model NO. : 1012380 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/ TV technician for help. B. 1 x Rear Body C. 1 x Antenna H. 1 x Connect Remote PCB and Antenna 2. 1 x Cross Screw ( 2.3 x 6 PWB x 6 ) Battery Cover Connect the wire from the battery compartment to the Circuit Board. NOTE: Circuit Board - R (connect Red wire) Y (connect Yellow wire) 1 2 1 12 3 5 4 D. 1 x Circuit Board 1. 2x Short Cross Screws ( 2.3 X 6 PB ) A. 1 x Front Body F. 2 x Joysticks E. 1 x On/Off Switch 1. 4 x Short Cross Screws ( 2.3 X 6 PB ) G. 1 x Battery Cover with Screw Attach the Front Body and Rear Body using screws provided. Insert a 9V battery (not included) matching the polarity etched in the battery tray. Attach the Battery Cover. Insert the Circuit Board into the back side of the Rear Body. Attach the Antenna to the Rear Body.Attach On/Off Switch and left and right Joysticks to the Front Body. BUILDING YOUR RACE TRIKE (continue) KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR FUTURE REFERENCE. Due to continuous product improvements, the pictures on this manual may differ slightly from the actual product. FAO ® and FAO Schwarz ® names and logos are trademarks or registered trademarks. All rights reserved. www.fao.com Distributed by and © 2020 MerchSource, LLC. Irvine, CA 92618. For customer supp…

Text truncated - open the document above for the full version.

APPENDIXE SHANTOUCHENGHAIYUANJIATOYSFACTORY Attention:CertificAtionreviewer RE:RequestforConfidentiAlity FCCID:2AKCIYJ2020C49MHZ ToWhomItMAyConcern: PermanentConfidentiality[Completethissectionifpermanentconfidentialityisrequested] RequesttowithholdpermAnentlyfrompublicreviewcertAinportionsoftheApplicAtionfor equipmentcertificAtionforthereferencedFCCidentifiers.ThisrequestforconfidentiAlityis mAdepursuAntto47CFR0.457(d)And0.459oftheFCCRules.InpArticulAr,thefollowing sectionsofthe A pplic A tion A retobekeptperm A nentlyconfidenti A l: [Selectoneormoreofitemsbelow,asappropriate,anddeleteunselectedparts] SchemAtics BlockDiAgrAms OperAtionAlDescription RAtionAleforrequestforconfidentiAlity: WehAVeinvestedconsiderAbletimeAndmAteriAlsinreseArchAnddevelopmenttoproducethereferenced product. Sincerely, 2020-5-11 [Date] Permanentconfidentiality:Disclosureoftheperm A nentlyconfidenti A lportionsofthis A pplic A tiontocompetitorswouldnotonlygivethemsignific A ntcompetitive A dv A nt A gesin developingsimilArproducts,butwouldAlsodisclosesuccessfulimplementAtionofunpublished, le A dingedgetechnologydevelopedbyus. IfyouhAVequestionsorneedfurtherinformAtion,pleAsecontACttheundersigned.

Page 1 of 2 External Photos Page 2 of 2

Page 1 of 1 Label Artwork and Location SIZE: 22mm (W) x 6mm (H) FCC ID ： 2AKCIYJ2020C49MHZ

Page 1 of 2 Internal Photos Page 2 of 2

1 INTERTEK TESTING SERVICES Analysis Report The equipment under test (EUT) is a transmitter for a Toy RC DIY Trike operating at 49.86 MHz which is controlled by a crystal. The EUT is powered by one 9.0V 6F22 battery. For more detail information pls. refer to the user manual Antenna Type: integral antenna Antenna Gain: 0dBi Modulation Type: Pulse modulation The nominal conducted output power specified: -28.0dBm (+/- 3dB) The nominal radiated output power (e.r.p) specified: -30.15dBm (+/- 3dB) According to the KDB 447498: The worst-case peak radiated emission for the EUT is 66.70dBuV/m at 3m in the frequency 49.86MHz The EIRP = [(FS*D) ^2 / 30] mW= -28.53dBm The ERP = EIRP – 2.15 = -30.68dBm which is within the production variation. The maximun conducted output power specified is -25.0dBm = 0.0032mW The source- based time-averaging conducted output power = 0.0032* Duty Cycle mW < 0.0032mW (Duty Cycle<100%) The SAR Exclusion Threshold Level for 49.860MHz when the minimum test separation distance is < 50mm: = 474 * [1 + log(100/f(MHz)]/2 = 308.6 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. Transmitter Duty Cycle Calculation The duration of one cycle = 21.3043ms Effective period of the cycle = 1.8696ms x 4 + 608.7μs x 10 =13.5654ms DC =13.5654ms / 21.3043ms =0.6367 or 63.67% FCC ID: 2AKCIYJ2020C49MHZ

SHANTOU CHENGHAI YUANJIA TOYS FACTORY TEST REPORT SCOPE OF WORK RF TESTING–1012380 REPORT NUMBER GZHH00360897-001 ISSUE DATE JULY 23, 2020 PAGES 16 DOCUMENT CONTROL NUMBER FCC ID_b-235 © 2017 INTERTEK Intertek Report No.: GZHH00360897-001 • The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community GuanHu Subdistrict, LongHua District, Shenzhen, People’s Republic of China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01 November 2017 Page: 1 of 16 FCC ID_b-235 Test Report SHANTOU CHENGHAI YUANJIA TOYS FACTORY Application For Certification FCC ID: 2AKCIYJ2020C49MHZ Product Name: Toy RC DIY Trike Model: 1012380 Additional Model: 1013258 Brand Name: Discovery Mindblown, FAO Schwarz Transmitter Report No.: GZHH00360897-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [ 10-1-19] Prepared and Checked by: Approved by: Sign on file Terry Tang Assistant Supervisor Jimmy Wen Assistant Manager Date: July 23, 2020 Intertek Report No.: GZHH00360897-001 Version: 01 November 2017 Page: 2 of 16 FCC ID_b-235 Test Report GENERAL INFORMATION SHANTOU CHENGHAI YUANJIA TOYS FACTORY MODEL: 1012380 FCC ID: 2AKCIYJ2020C49MHZ Grantee: SHANTOU CHENGHAI YUANJIA TOYS FACTORY Grantee Address: Lanyuan Area, Lianshan Town, Chenghai District Shantou, Guangdong China Contact Person: Xia Li Tel: 0754-8114393 Manufacturer: SHANTOU CHENGHAI YUANJIA TOYS FACTORY Manufacturer Address: Lanyuan Area, Lianshan Town, Chenghai District Shantou, Guangdong China Model: 1012380 Type of EUT: Transmitter Description of EUT: Toy RC DIY Trike Serial Number: N/A FCC ID : 2AKCIYJ2020C49MHZ Date of Sample Submitted: April 23, 2020 Date of Test: April 27, 2020 Report No.: GZHH00360897-001 Report Date: July 23, 2020 Environmental Conidtions: Temperature: +10 to 40°C Humidity: 10 to 90% Intertek Report No.: GZHH00360897-001 Version: 01 November 2017 Page: 3 of 16 FCC ID_b-235 Test Report SUMMARY OF TEST RESULT SHANTOU CHENGHAI YUANJIA TOYS FACTORY MODEL: 1012380 FCC ID: 2AKCIYJ2020C49MHZ TEST SPECIFICATION REFERENCE RESULTS Maximum Peak Output Power 15.247(b), (c) / RSS-210 A8.4 N/A Hopping Channel Carrier Frequencies Separation (for 2.4GHz Digital) 15.247(e) / RSS-210 A8.1 N/A 20dB Bandwidth of the Hopping Channel 15.247(a) / RSS-210 A8.1 N/A Number of Hopping Frequencies 15.247(e) / RSS-210 A8.1 N/A Average Time of Occupancy of Hopping Frequency 15.247(e) / RSS-210 A8.1 N/A Anteann Conducted Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A Radiated Spurious Emissions 15.247(d) / RSS-210 A8.5 N/A RF Exposure Compliance 15.247(i) / RSS-Gen 5.5 N/A Transmitter Power Line Conducted Emissions 15.207 / RSS-Gen 7.2.2 N/A Transmitter Field Strength (for 27MHz) 15.227 / RSS-310 3.8 N/A Transmitter Field Strength (for 40MHz) 15.229 / RSS-210 A2.7 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for Remote Control) 15.231(a) / RSS-210 A1.1.1 N/A Transmitter Field Strength, Bandwidth and Timing Requirement (for 433MHz) 15.231(e) / RSS-210 A1.1.5 N/A Transmitter Field Strength and Bandwidth Requirement(for 88-108MHz) 15.239 / RSS-210 A2.8 N/A Transmitter Field Strength and Bandwidth Requirement(for 902- 928MHz or 2.4GHz) 15.249 / RSS-210 A2.9 N/A Transmitter Field Strength and Bandwidth Requirement (for 49MHz) 15.235 / RSS-310 3.9 Pass Receiver / Digital Device Radiated Eissions 15.109 / ICES-003 N/A Digital Device Conducted Emissions 15.107 / ICES-003 N/A Note: 1. The EUT uses an integral antenna, in accordance to section 15.203, is considered sufficient to comply with the provisions of this section. 2. Pursuant to FCC part 15 Section 15.215(c), the 20 dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over excepted variations in temperature and supply voltage were considered. Intertek Report No.: GZHH00360897-001 Version: 01 November 2017 Page: 4 of 16 FCC ID_b-235 Test Report Table of Contents 1.0 General Description ..................................................................................................................................... 5 1.1 Product Description .................................................................................................................................... 5 1.2 Related Submittal(s) Grants ...................................................................................................................... 5 1.3 Test Methodology ...........................................................…

Text truncated - open the document above for the full version.

Page 1 of 1 Radiated Photos (EUT was placed in the center of the turntable)