2AKU5ZC17Firefighter thermal camera

- 1 - Fire special thermal camera quick operation manual - 2 - Thank you for purchasing this product, please read this manual before use, after reading, please carefully store for future reference. We hope this product will meet your expectations. - IMPORTANT – This manual is a general manual for a series of products, which means that the specific model of the product you receive may be different from the manual picture, please refer to the physical receipt. his user manual is organized for the convenience of users to use and understand the company's products, we will do our best to ensure the accuracy of the content of this manual, but still cannot guarantee the completeness of the content of this manual, because our products have been continuously updated and upgraded, the company reserves the right to modify at any time without prior notice。 - 3 - - FCC WARNING – Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comp ly with the limits for a Class B digital device, p ursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofr equency energy and, if not installed and used in ac cordance with the instructions, may cause harmful int erference to radio communications. However, there isno guarantee that interference will not occur in a pa rticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct t he interference by one or more of the following mea - 4 - sures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Ru les.Operation is subject to the following two conditi ons:(1) This device may not cause harmful interferenc e, and (2) this device must accept any interference received, including interference that may cause undesi redoperation. The device has been evaluated to meet general RF Exposure requirement. The device can be used in Portable Exposure condition without restriction. - 5 - - CONSIDERATIONS – Danger 1) Charge the battery as instructed in the Guide and follow the charge steps and precautions. Incorrect charging can cause heating or damage of the battery or even cause personal injury; 2) Never attempt to open or disassemble the battery; if the battery leaks and the liquid enters eyes, immediately flush the eyes with water and then take necessary medical care. WARNING 1) When using the equipment, please try to keep it stable and avoid violent shaking. 2) Do not use or store the instrument in an environment beyond the permitted operating temperature or storage temperature of the equipment. - 6 - 3) Do not direct the equipment at high intensity thermal radiation sources, such as the sun, lasers, spot welders, etc. 4) Do not plug the hole in the device. 5) Do not knock, throw or vibrate instruments and accessories to avoid damage. 6) Do not disassemble the machine by yourself, which may cause damage to the equipment and loss of warranty rights. 7) Do not use dissolved or similar liquids on equipment or cables, which may cause damage to the equipment. 8) Please do not use the equipment in an environment that exceeds the operating temperature of the equipment, which may cause damage to the equipment. 9) Please follow the following measures when wiping the equipment： Non-optical surface: When necessary, you can use a clean and soft cloth to wipe the non-optical surface of the thermal camera. - 7 - Optical surface: Please avoid staining the optical surface of the lens when using the thermal camera, especially avoid touching the lens with your hands, because the sweat on your hands will leave traces on the lens glass and may corrode the optical coating layer on the glass surface. When the surface of the optical lens is contaminated, use professional lens paper to carefully wipe. 10) Do not place the battery in a high temperature environment or near high temperature objects. 11) Do not short-circuit the positive and negative terminals of the battery. 12) Do not place the battery in a humid environment or water. CAUTION 1) Do not expose the equipment to dust or damp environment. When used in an environment with water, water should be avoided on the instrument. Cover the - 8 - lens when not in use. 2) When the equipment is not in use, please place the instrument and all accessories in a special packaging box. - Storage and Transportation - Storage: A packaged product shall be stored in a well-ventilated and clean environment with a temperature range of -40° C to 85° C, a relative humidity not exceeding 95%, and free of condensate and corrosive gas. Transportation： During transportation and circulation, the product shall be protected from rain and water and placed flatwise. It shall be protected from violent vibration and impact. During handling, it shall be handled with care and cannot be tossed. - 9 - –Product Introduction– This product is specially designed for fire protection infrared thermal imager, mainly used for fire fighting and rescue, fire inspection, rescue and disaster relief operations. It can guide firefighters to rescue personnel under harsh smoke and high temperature fire site conditions, find the fire source, prevent firefighters from straying into high temperature dangerous areas, and ensure the property and life safety of the masses. This product is usually handheld, both detection type and rescue type. Use battery power, with infrared image display, temperature in…

Text truncated - open the document above for the full version.

Rev 1/26/2023 Wuhan Guide Sensmart Tech Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-12-2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AKU5ZC17 [Wuhan Guide Sensmart Tech Co., Ltd] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (Applicant printed name) Yong Bao Rev 1/26/2023 Wuhan Guide Sensmart Tech Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-12-2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AKU5ZC17 [Wuhan Guide Sensmart Tech Co., Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (Applicant printed name) Yong Bao

Rev 1/26/2023 Wuhan Guide Sensmart Tech Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 07-12-2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AKU5ZC17 [Wuhan Guide Sensmart Tech Co., Ltd] (“the applicant”) certifies that, as of the date of the filing of the application, [FCC US Agent, LLC] is our designated U.S. agent for service of process for the above referenced FCC ID. [Wuhan Guide Sensmart Tech Co., Ltd] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. [FCC US Agent, LLC] accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Email: [email protected] Sincerely, Wuhan Guide Sensmart Tech Co., Ltd FCC US Agent, LLC Yong Bao Tim Payne

Wuhan Guide Sensmart Tech Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 2023-07-12 SUBJECT: FCC Application for FCC ID: 2AKU5ZC17 To Whom It May Concern: We, the undersigned, hereby authorize Lisa Wang at EMTEK (SHENZHEN) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK (SHENZHEN) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Yong Bao Wuhan Guide Sensmart Tech Co., Ltd

Rev 11/20/07 Wuhan Guide Sensmart Tech Co., Ltd Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AKU5ZC17 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram, Schematics, Operational Description, Block Diagram Operation Description schematic diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Yong Bao Wuhan Guide Sensmart Tech Co., Ltd

Declaration on model difference We the undersigned hereby confirm that any of our production units bearing the following model numbers are identical in circuitry and electrical, mechanical and physical construction; the only differences are the model name for trading purpose. FCC ID: 2AKU5ZC17 Production name Trade name Model no. Firefighter thermal camera Guide PR410/F384/PR610/F640 Confirmed by Wuhan Guide Sensmart Tech Co., Ltd Yong Bao Wuhan Guide Sensmart Tech Co., Ltd Date: 2023-07-12

Wuhan Guide Sensmart Tech Co., Ltd Date: 2023-07-12 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AKU5ZC17 To Whom It May Concern: This letter is to ascertain that Wuhan Guide Sensmart Tech Co., Ltd EUT：Firefighter thermal camera MODEL No.: PR410/F384/PR610/F640 Has been the units used for conducting FCC compliance testing, the SDoC part will be tested by EMTEK (SHENZHEN) CO., LTD. If you have any question or concerns, pls. contact us. Sincerely, Client’s signature ： Client’s name / title ： Yong Bao Contact information / address: Wuhan Guide Sensmart Tech Co., Ltd /NO.29,Gaoxin 3rd Road,Donghu New-tech Development Zone,Wuhan City,Hubei,P.R.China

Antenna

FCC ID: 2AKU5ZC17 According to § 15.247(i) and § 1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB447498 D01 General RF Exposure Guidance V06 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] * [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz； Power and distance are rounded to the nearest mW and mm before calculation； The result is rounded to one decimal place for comparison； The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. We use 5mm as separation distance to calculate. Maximum measured transmitter power: Transmit Frequency (GHz) Mode Max Conducted Power (dBm) tune up maximum power(dBm) Result calculation 1-g SAR 2412 11B 8.59 9.5 2.768 3 2437 11B 6.71 9.5 2.783 3 2462 11B 8.81 9.5 2.797 3 2412 11G 8.93 9.5 2.768 3 2437 11G 7.35 9.5 2.783 3 2462 11G 8.96 9.5 2.797 3 2412 11N20SISO 8.61 9.5 2.768 3 2437 11N20SISO 7.35 9.5 2.783 3 2462 11N20SISO 9.09 9.5 2.797 3 Conclusion: For the max result : 2.797≤ 3.0 for 1-g SAR extremity SAR, No SAR is required. Signature: Date: 2023.07.12 NAME AND TITLE (Please print or type): Lisa Wang/Manager COMPANY (Please print or type): Shenzhen EMTEK Co.,Ltd./Building 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China

Report No. ENS2304100255W00201R Page 1 of 58 Ver.1.0 TEST REPORT Product Name ： Firefighter thermal camera Model Number ： PR410/F384/PR610/F640 FCC ID ： 2AKU5ZC17 Prepared for : Wuhan Guide Sensmart Tech Co., Ltd Address : NO.29,Gaoxin 3rd Road,Donghu New-tech Development Zone,Wuhan City,Hubei,P.R.China Prepared by : EMTEK (SHENZHEN) CO., LTD. Address : Building 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26954280 Fax: (0755) 26954282 Report Number : ENS2304100255W00201R Date(s) of Tests : May 18, 2023 to June 30, 2023 Date of issue : July 3, 2023 $二维码$ Report No. ENS2304100255W00201R Page 2 of 58 Ver.1.0 TEST RESULT CERTIFICATION Applicant : Wuhan Guide Sensmart Tech Co., Ltd Address : NO.29,Gaoxin 3rd Road,Donghu New-tech Development Zone,Wuhan City,Hubei,P.R.China Manufacturer : Wuhan Guide Sensmart Tech Co., Ltd Address : NO.29,Gaoxin 3rd Road,Donghu New-tech Development Zone,Wuhan City,Hubei,P.R.China EUT : Firefighter thermal camera Model Name : PR410/F384/PR610/F640 Trademark : Guide Measurement Procedure Used: APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 2 , Subpart J FCC 47 CFR Part 15 , Subpart C PASS The above equipment was tested by EMTEK (SHENZHEN) CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.247 The test results of this report relate only to the tested sample identified in this report. Date of Test : May 18, 2023 to June 30, 2023 Prepared by : Una Yu /Editor Reviewer : Joe Xia/Supervisor Approve & Authorized Signer : Lisa Wang/Manager Report No. ENS2304100255W00201R Page 3 of 58 Ver.1.0 Modified History Version Report No. Revision Date Summary V1.0 ENS2304100255W00201R / Original Report Report No. ENS2304100255W00201R Page 4 of 58 Ver.1.0 TABLE OF CONTENTS 1 EUT TECHNICAL DESCRIPTION .......................................................................................................... 5 2 SUMMARY OF TEST RESULT............................................................................................................... 6 3 TEST METHODOLOGY .......................................................................................................................... 7 3.1 General Description Of Applied Standards ....................................................................................... 7 3.2 Measurement Equipment Used ........................................................................................................ 7 3.3 Description Of Test Modes ............................................................................................................... 8 4 FACILITIES AND ACCREDITATIONS .................................................................................................... 9 4.1 Facilities ............................................................................................................................................ 9 4.2 Equipment ........................................................................................................................................ 9 4.3 Laboratory Accreditations And Listings ............................................................................................ 9 5 TEST SYSTEM UNCERTAINTY ........................................................................................................... 10 6 SETUP OF EQUIPMENT UNDER TEST .............................................................................................. 11 6.1 Radio Frequency Test Setup 1 ....................................................................................................... 11 6.2 Radio Frequency Test Setup 2 ....................................................................................................... 11 6.3 Conducted Emission Test Setup .................................................................................................... 14 6.4 Block Diagram Configuration Of Test System ................................................................................ 15 6.5 Support Equipment ......................................................................................................................... 15 7 TEST REQUIREMENTS ....................................................................................................................... 16 7.1 Minimum (6db) Occupied Bandwidth ............................................................................................. 16 7.2 Maximum Peak Conducted Output Power ..................................................................................... 20 7.3 Maximum Power Spectral Density .................................................................................................. 25 7.4 Unwanted Spurious Emissions ....................................................................................................... 29 7.5 Radiated Emission .......................................................................................................................... 42 7.6 Conducted Emission Test ............................................................................................................... 54 7.7 Antenna Application ........................................................................................................................ 57 Report No. ENS2304100255W00201R Page 5 of 58 Ver.1.0 1 EUT TECHNICAL DESCRIPTION Note: for more details, please refer to the user’s manual of the EUT. Characteristics Description Product Firefighter thermal camera Model Number PR410/F384/PR610/F640 Sample Number 2# IEEE 802.11 WLAN Mode Supported 802.11b 802.11g 802.11n(20MHz channel bandwidth) 802.11n(40MHz channel bandwidth) Modulation DSSS with DBPSK/DQPSK/CCK for 802.11b; OFDM with BPSK/QPSK/16QAM/64Q…

Text truncated - open the document above for the full version.

Dongguan YiJia Electronics Communication Technology Co.,Ltd. SPECIFICATION FOR APPROVAL Date 2023/06/30 File No 23063001 Revision 1.0 Wuhan Guide Sensmart Tech Co., Ltd CUSTOMER: CUSTOMER NO: ZC17A WIFI Antenna L 110mm MHFWIFI Antenna L=110mm MHF YJT01.220.019.301A PART NAM E: SUPPLIER NO: Date: CUS TOMER APPROVED BY APPROVALCHIEFSUPERVISOR S UPPLIER SIGNATURE APPROVALCHECKDESIGN add：Yuanfu Industrial Zone, 59 Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax :0769-82586086 APPROVALCHECKDESIGN ChenGuoqiangXieLiLiaoGuangxi YJ-RD-F04-A Admission book item table NO . Contents Number of Page PageCode 111 Spec Cover） 2 Spec Item 12 3 Drawing 13 4 Antenna Specification 14 5 S Parameter 15 6 Pass ive Test 16 7 Radiation Pattern 17 8- -- 99--- 10--- 11--- add：Yuanfu Industrial Zone, 59 Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax:0769-82586086 12--- 13--- -2 RoHS | C(）1I兀门口p| -3--4 5- CUSTOMER PART NO -6- 詈 7 DESCRIPTION initial issue 8 DATE 2023-04-18 EE 24.2 DI Cl 110.0士4.0 B Notes: 1.0 Electrical: 1.1 Frequency：2400~2500MHz 1.2 Impedance：50 O hm Nominal 1.3 V.S.W.R：S2.0 1.4 Gain：3.4dB 1.5 Radiation：Omni-directional 1.6 P olarization：Linear 2.0 Enviromental: 2 . 1 S t o r a g e T e m p e r a t u r e R a n g e ： － 4 0 T o + 8 5 ° C 2.2 Operating Temperature Range：－40 T o +85 ° C 3.0 All material must meet ROHS Request. L i | 三 ＾ az D 吵 Dongguan YiJia Electronics Communication Technology Co.,Ltd. Fax:0769 -82586086 PART NAME: WIFI Antenna L=110mm MHF PART NO.： YJT01.220.019.301A | DATE: 2023-04-18 c B A l 3 FPC 24.2*22.2mm FPC FPC10510A.P01 2 Coaxial Cable O.D.1.13 Black O.D.1.13 COA100X邓．P01 1 1 Mini Connector Au Plated Cu TER100XXA.P01 1 NO PART NAME DESCRIPTION Material Part Number Q.TY 2 I 3 APPROVED BY CHECKED BY DESIGNED BY ， Tolerance A x.x 士0.50 x.xx 土0.15 -5- -6--7- UNITS: mm SCALE: 1/1 RE VIS|O N: A | X ° 土3 0 8 Antenna Specification Electrical Properties Frequency 2.4-2.5GHz qy Impedance50 Ohm Nominal V.S.W.R2.0 Max Gain 34dBi Gain 3.4 dBi RadiationOmni-directional PolarizationLinear Physical Properties Connector First generation IPEX Cable TypeO.D.1.13mm Cable Length110mm Cable ColorBlack add：Yuanfu Industrial Zone, 59 Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax :0769-82586086 Operating Temp.-40 ~ +85 ̊C Storage Temp / Humidity 25±5 ̊C / <70% AntennaPerformance Test Agilent Antenna Performance Te s t Agilent E5071B SS Parameter Test // WiFi Antenna add：Yuanfu Industrial Zone, 59 Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax :0769-82586086 AntennaPassive Test Passive Test For WiFi Antenna FreqEffiEffiGain Antenna Passive Te s t (MHz)(%)(dB)(dBi) 2400 54.9-2.62.3 2410 54.9-2.62.4 2420 55.1-2.62.6 2430 57.6-2.42.7 2440 57.8-2.42.7 2450 58.2-2.43.4 2460 54.2-2.73.2 2470 53.9-2.73.0 2480 53.8-2.72.8 add：Yuanfu Industrial Zone, 59 Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax :0769-82586086 2490 53.6-2.72.7 2500 53.5-2.72.6 Radiation Pattern For WiFi Antenna(2450MHz) add：Yuanfu Industrial Zone, 59 Muyu Road, Shatou Community, Changan Town, Dongguan City Tel:0769-82586086 Fax :0769-82586086

TEST SETUP PHOTOGRAPHS 1.1. Photos of Conducted Emission Measurement 1.2. Photos of Radiation Emission Measurement Spurious Emission Test Setup (Below 1GHz) Spurious Emission Test Setup (Above 1GHz) ----------------The end----------------