2ALAI19MT103Weighing terminal

Installation Manual IND256x Weighing Terminal Installation Manual | Guía de instalación | Installationshandbuch | Guide d’installation | Guida all’installazione | Guia de instalação IND256x Weighing Terminal Essential Services for Dependable Performance of Your IND256x Weighing Terminal Congratulations on choosing the quality and precision of METTLER TOLEDO. Proper use of your new equipment according to this Manual and regular calibration and maintenance by our factory- trained service team ensures dependable and accurate operation, protecting your investment. Contact us about a service agreement tailored to your needs and budget. Further information is available at www.mt.com/service. There are several important ways to ensure you maximize the performance of your investment: 1. Register your product: We invite you to register your product at www.mt.com/productregistration so we can contact you about enhancements, updates and important notifications concerning your product. 2. Contact METTLER TOLEDO for service: The value of a measurement is proportional to its accuracy – an out of specification scale can diminish quality, reduce profits and increase liability. Timely service from METTLER TOLEDO will ensure accuracy and optimize uptime and equipment life. a. Installation, Configuration, Integration and Training: Our service representatives are factory- trained, weighing equipment experts. We make certain that your weighing equipment is ready for production in a cost effective and timely fashion and that personnel are trained for success. b. Initial Calibration Documentation: The installation environment and application requirements are unique for every industrial scale so performance must be tested and certified. Our calibration services and certificates document accuracy to ensure production quality and provide a quality system record of performance. c. Periodic Calibration Maintenance: A Calibration Service Agreement provides on-going confidence in your weighing process and documentation of compliance with requirements. We offer a variety of service plans that are scheduled to meet your needs and designed to fit your budget. d. GWP ® Verification: A risk-based approach for managing weighing equipment allows for control and improvement of the entire measuring process, which ensures reproducible product quality and minimizes process costs. GWP (Good Weighing Practice), the science- based standard for efficient life-cycle management of weighing equipment, gives clear answers about how to specify, calibrate and ensure accuracy of weighing equipment, independent of make or brand. © METTLER TOLEDO 2020 No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of METTLER TOLEDO. U.S. Government Restricted Rights: This documentation is furnished with Restricted Rights. Copyright 2020 METTLER TOLEDO. This documentation contains proprietary information of METTLER TOLEDO. It may not be copied in whole or in part without the express written consent of METTLER TOLEDO. METTLER TOLEDO reserves the right to make refinements or changes to the product or manual without notice. COPYRIGHT METTLER TOLEDO ® is a registered trademark of Mettler-Toledo, LLC. All other brand or product names are trademarks or registered trademarks of their respective companies. METTLER TOLEDO RESERVES THE RIGHT TO MAKE REFINEMENTS OR CHANGES WITHOUT NOTICE. FCC Notice This device complies with Part 15 of the FCC Rules and the Radio Interference Requirements of the Canadian Department of Communications. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. Declaration of Conformity is available at http://glo.mt.com/global/en/home/search/compliance.html/compliance/. FCC RF Safety Statement To satisfy FCC RF exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The device has been evaluated to meet general RF exposure requirement. IC Notice This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is sub…

Text truncated - open the document above for the full version.

FIGURE 1 WEIGHING TERMINAL (M/N: IND256X) G ENERAL APPEARANCE (TOP VIEW) F IGURE 2 WEIGHING TERMINAL (M/N: IND256X) GENERAL APPEARANCE (FRONT VIEW) FIGURE 3 WEIGHING TERMINAL (M/N: IND256X) G ENERAL APPEARANCE (LEFT VIEW) F IGURE 4 WEIGHING TERMINAL (M/N: IND256X) GENERAL APPEARANCE (BACK VIEW) FIGURE 5 WEIGHING TERMINAL (M/N: IND256X) G ENERAL APPEARANCE (RIGHT VIEW) F IGURE 6 WEIGHING TERMINAL (M/N: IND256X) GENERAL APPEARANCE (BOTTOM VIEW) FIGURE 7 WEIGHING TERMINAL (M/N: IND256X) G ENERAL APPEARANCE (ANTENNA LOCATED) F IGURE 8 WEIGHING TERMINAL (M/N: IND256X) ANTENNA Antenna

Label Location Information Refer to the below red arrow: (For example)

FIGURE 9 WEIGHING TERMINAL (M/N: IND256X) C OVER REMOVED F IGURE 10 WEIGHING TERMINAL (M/N: IND256X) DISPLAY BOARD (COMPONENT SIDE) FIGURE 11 WEIGHING TERMINAL (M/N: IND256X) D ISPLAY BOARD (SOLDERED SIDE) F IGURE 12 WEIGHING TERMINAL (M/N: IND256X) MAIN BOARD (COMPONENT SIDE) FIGURE 13 WEIGHING TERMINAL (M/N: IND256X) M AIN BOARD (SOLDERED SIDE) F IGURE 14 WEIGHING TERMINAL (M/N: IND256X) CRYSTAL & CHIP ON MAIN BOARD FIGURE 15 WEIGHING TERMINAL (M/N: IND256X) C RYSTAL & CHIP ON MAIN BOARD F IGURE 16 WEIGHING TERMINAL (M/N: IND256X) RF BOARD (COMPONENT SIDE) FIGURE 17 WEIGHING TERMINAL (M/N: IND256X) RF BOARD (SOLDERED SIDE) F IGURE 18 WEIGHING TERMINAL (M/N: IND256X) CRYSTAL & CHIP ON RF BOARD FIGURE 19 WEIGHING TERMINAL (M/N: IND256X) RF MODULE (BACK VIEW)

Applicant: Mettler Toledo (Changzhou) Measurement Technology Co., Ltd. Product Name: Weighing terminal Model Number: IND256x FCC ID: 2ALAI19MT103 RADIO FRREQUENCY EXPOSURE COMPLIANCE RESULT: Test Standard: FCC CFR 47 §1.1310 : Radiofrequency radiation exposure limits. Note: (1) Occupational/controlled exposure limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for occupational/controlled exposure also apply in situations when a person is transient through a location where occupational/controlled limits apply provided he or she is made aware of the potential for exposure. (2) General population/uncontrolled exposure limits apply in situations in which the general public may be exposed, or in which persons who are exposed as a consequence of their employment may not be fully aware of the potential for exposure or cannot exercise control over their exposure. MPE Calculation Standard: MPEሺSሻ ൌ PG/ሺ4ܴߨ ଶ ) where: S = power density (in appropriate units, e.g. mW/ cm 2 ) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) Calculation Result: For this EUT, General population/uncontrolled exposure limits applied. The limit value 1.0mW/cm 2 is available for this EUT. Modulation Peak Output Power Antenna Gain MPE Limit Verdict (dBm) (mW) (dBi) (Numeric)(mW/cm 2 ) (mW/cm 2 ) 802.11b 16.47 44.3609 3 1.99526 0.01761 1.0 Compliant 802.11g 20.93 123.88 3 1.99526 0.04917 1.0 Compliant 802.11n20 20.37 108.893 3 1.99526 0.04322 1.0 Compliant For R = 20cm

Mettler Toledo (Changzhou) Measurement Technology Co., Ltd. FCC ID: 2ALAI19MT103 Page 1 of 71 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F20011 Prepared For: Mettler Toledo (Changzhou) Measurement Technology Co., Ltd. No. 111 West Taihu Road, Changzhou City, Jiangsu Province, China. Prepared By: Audix Technology (Shanghai) Co., Ltd. 3F and 4F, 34Bldg, 680 Guiping Rd., Caohejing Hi-Tech Park, Shanghai 200233, China Tel: +86-21-64955500 Fax: +86-21-64955491 File No. : C1D1912002 Report No. : ACI-F20011 Date of Test : 2019.12.09-2020.01.06 Date of Report : 2020.01.15 TEST REPORT On behalf of Mettler Toledo (Changzhou) Measurement Technology Co., Ltd. Product Name: Weighing terminal Model No.: IND256x FCC ID: 2ALAI19MT103 The statement is based on a single evaluation of one sample of the above-mentioned products. It does not imply an assessment of the whole production and does not permit the use of the test lab logo. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TESTING NVLAP LAB CODE 200371-0 Mettler Toledo (Changzhou) Measurement Technology Co., Ltd. FCC ID: 2ALAI19MT103 Page 2 of 71 Audix Technology (Shanghai) Co., Ltd. Report No.: ACI-F20011 TABLE OF CONTENTS Page 1SUMMARY OF STANDARDS AND RESULTS .......................................................................... 5 1.1Description of Standards and Results ......................................................................................... 5 2GENERAL INFORMATION .......................................................................................................... 6 2.1Description of Equipment Under Test ........................................................................................ 6 2.2EUT Specifications Assessed in Current Report ........................................................................ 7 2.3Test Information ......................................................................................................................... 7 2.4Supported equipment .................................................................................................................. 7 2.5Description of Test Facility ........................................................................................................ 8 3RADIATED EMISSION TEST ....................................................................................................... 9 3.1Test Equipment ........................................................................................................................... 9 3.2Block Diagram of Test Setup ..................................................................................................... 9 3.3Radiated Emission Limit (§15.209) ......................................................................................... 10 3.4Test Configuration .................................................................................................................... 10 3.5Operating Condition of EUT .................................................................................................... 11 3.6Test Procedures ........................................................................................................................ 11 3.7Test Results .............................................................................................................................. 12 46 DB BANDWIDTH MEASUREMENT ...................................................................................... 23 4.1Test Equipment ......................................................................................................................... 23 4.2Block Diagram of Test Setup ................................................................................................... 23 4.3Specification Limits (§15.247(a)(2)) ........................................................................................ 23 4.4Operating Condition of EUT .................................................................................................... 23 4.5 Test Procedure .......................................................................................................................... 23 4.6Test Results .............................................................................................................................. 24 5MAXIMUM PEAK OUTPUT POWER MEASUREMENT ...................................................... 30 5.1Test Equipment ......................................................................................................................... 30 5.2Block Diagram of Test Setup ................................................................................................... 30 5.3Specification Limits ((§15.247(b)(3)) ...................................................................................... 30 5.4Operating Condition of EUT .................................................................................................... 30 5.5Test Procedure .......................................................................................................................... 30 5.6Test Results .............................................................................................................................. 31 6EMISSION LIMITATIONS MEASUREMENT ......................................................................... 37 6.1Test Equipment ......................................................................................................................... 37 6.2Block Diagram of Test Setup ................................................................................................... 37 6.3Specification Limits (§15.247(d)) ............................................................................................ 37 6.4Operating Condition of EUT .........................................…

Text truncated - open the document above for the full version.

Test Set-Up Photos 1. Radiated Test (B ELOW 1GHZ) (A BOVE 1GHZ) 2. Antenna-port Conducted Test