2ALB6-LMAMBLE01Remote Control

LIMA M1 remote control Take Off Guide 1. Lima M1 Remote Control 2. Turn On Lima M1 Lima M1 remote control arrives with a 2 AAA batteries blister inside a polybag. To turn on your Lima M1 remote control, please follow the instructions below. 1. Turn ON your TV and your Set Top Box. 2. Remove your Lima M1 remote control and its batteries from the plastic bag. 3. Remove the remote’s battery lid. 4. Place the batteries on the Lima M1 remote control as indicated in the image above and replace the battery lid. 5. After inserting the batteries, wait a few seconds and the Lima M1 remote will be ready to operate the Set-Top-Box. FCC Compliance Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determinated by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. .Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation expuser limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION Risk of explosion if the battery is replaced by an incorrect type, disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

T. +351 256 001 930 www.tech4home.pt NIF. 509 195 830 [email protected] Centro Empresarial e Tecnológico de S. João da Madeira Rua de Fundões, nº 151 3700-121 S. João da Madeira Portugal S. João da Madeira, May 28, 2021 Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Tech4home, Lda FCC ID: 2ALB6-LMAMBLE01 To Whom It May Concern: We, Tech4Home, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2ALB6- LMAMBLE01 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is May 28, 2021. The Limited Agency Agreement expires on May 28, 2022, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Miguel Valente Total Quality Manager

Tech4home, Lda Attention: Certification reviewer RE: Request for Confidentiality 2ALB6-LMAMBLE01 To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] Schematics Block Diagrams Operational Description Tune-up Procedure Parts List Internal Photos (see note) Users Manual (see note) Note 1: Internal Photos may be held confidential 1) if the circuit board or internal components are not accessible to users. For example, it is acceptable if the circuit board is enclosed in epoxy. 2) Also, it is acceptable if the device is not accessible to the public, for example, a device mounted on the top of a large tower (or in a fenced enclosure) such that it is only serviceable by professional designated technicians under a Non-Disclosure Agreement (NDA). All sales for these devices must be under a NDA restricting the disclosure of the propriety information, including internal photos. User Manual may be held confidential only when the manual contains proprietary technical information intended for professional technicians obligated under a NDA. All sales and distribution of the user’s manual must be under a NDA that restricts the disclosure of the information. In the application cover letter requesting permanent confidentiality the following additional description and the NDA exhibit is required: 1. Describe in detail how internal photos and/or users manual information are controlled to prevent them from becoming public or disclosed to unauthorized persons. 2. Describe how public access is restricted for products serviceable by professional designated technicians. 3. A statement that all sales of the non-consumer device will be under a NDA to include third party sales and that the final user of the device is subject to the NDA. 4. Provide an example of the NDA between the grantee and a purchaser. The request for confidentiality must Note 2: For scanning receiver, the schematics, block diagrams, operational description, tune-up procedure, parts list and internal photos are always held permanently confidential. Short-term Confidentiality [Complete this section if short-term confidentiality is requested] Request to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept short-term confidential for a period above from the date of the grant [ Select one or more of items below that are not selected in the list above, as appropriate] Schematics Block diagrams Operational Description Tune-up Procedure Parts List Test Setup Photos External Photos Internal Photos Users Manual Rationale for request for confidentiality: We have invested considerable time and materials in research and development to produce the referenced product. Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. Short-term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. If you have questions or need further information, please contact the undersigned. Sincerely, _______________ Miguel Valente TQM May 17, 2021

External photos APPENDIX C Label Artwork Each equipment covered in the certification for equipment authorization shall bear a label listing as the following: 1) An FCC ID, which should be printed in the following format with legible lettering. Eight point type is acceptable. FCC ID: 2ALB6-LMAMBLE01 “FCC ID” - in capital letters on a single line. 2ALB6 - your grantee code as assigned by the FCC (may be three or five). LMAMBLE01 - up to 14 alphanumeric characters you select. Dash or hyphen (-) may be used. No spaces are allowed. 2) Label artwork Note 1: The label shall not be a stick-on paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase. “Permanently affixed” means that the label is etched, engraved, stamped, silkscreened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable. Note 2: Label dimensions in millimeters. Note 3: Above labelling example is for reference only, may have some differences with to actual product.











 



   

 
   




  


 






 


 


 
 
 
 
  


 

 

 




   


!"#
$

 
 


 
 

 

$

 


  



% 



 

 
$


&
    
 

 

"

 
%$





'
 



(










)





 *$
 


)



 


   
 +



 


 
  









,   
 +#
 




 -
 -
  -
 * -
 
 -

  
   
*


   
 



 



   

 -
 -

 
  
  


 

 -
  -


  
 

)



  



+  
  


 


   

 

 


  
 



 
 


.
    

  


/
 
+ 


 
 -


 
  
 

 
 

Internal photos Antenna

INTERTEK TESTING SERVICES RF Exposure The equipment under test (EUT) is a Remote Control with Bluetooth function operating in 2402-2480MHz. The EUT is powered by DC 3.0V(2*1.5V AAA batteries), For more detail information pls. refer to the user manual. Bluetooth Version: 5.0 BLE (Single Mode) Antenna Type: Integral antenna Modulation Type: GFSK Antenna Gain: 0.0dBi Max The nominal conducted output power specified: 2.0dBm (+/-1dB) The nominal radiated output power(e.i.r.p) specified: 2.0dBm (+/-1dB) According to the KDB 447498: The Maximum peak radiated emission for the EUT is 97.5 dBμV/m at 3m in the frequency 2440MHz The EIRP = [(FS*D) ^2 / 30] mW = 2.27dBm which is within the production variation. The Minimum peak radiated emission for the EUT is 97.1 dBμV/m at 3m in the frequency 2480MHz The EIRP = [(FS*D) ^2 / 30] mW = 1.87dBm which is within the production variation. The maximun conducted output power specified is 3dBm = 2.0mW The source- based time-averaging conducted output power = 2.0 * Duty factor mW (where Duty Factor≤1) = 2.0 mW The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mW Since the source-based time-averaging conducted output power is well below the SAR low threshold level, so the EUT is considered to comply with SAR requirement without testing. FCC ID: 2ALB6-LMAMBLE01

Tech4home, Lda TEST REPORT SCOPE OF WORK FCC TESTING–T4HU2052 31k Lima M1, Lima M1 BLE, LMAMBLE01 REPORT NUMBER 210519017SZN-001 ISSUE DATE [REVISED DATE] 29 June 2021 [---------------------] PAGES 23 DOCUMENT CONTROL NUMBER FCC ID 249_C © 2017 INTERTEK Intertek Report No.: 210519017SZN-001 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Version: 01-November-2017 Page: 1 of 23 FCC ID 249_C Test Report Tech4home, Lda Application For Certification FCC ID: 2ALB6-LMAMBLE01 Remote Control Model: T4HU2052 31k Lima M1, Lima M1 BLE, LMAMBLE01 Brand Name: Tech4home 2.4GHz Transceiver Report No.: 210519017SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-19] Prepared and Checked by: Approved by: Ron Fan Engineer Peter Kang Sr. Technical Supervisor Date: 29 June 2021 Intertek Report No.: 210519017SZN-001 Version: 01-November-2017 Page: 2 of 23 FCC ID 249_C Test Report MEASUREMENT/TECHNICAL REPORT This report concerns (check one:) Original Grant X Class II Change Equipment Type: DXX - Part 15 Low Power Communication Device Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator − the new 47 CFR [10-1-19 Edition] provision. Report prepared by: Ron Fan Intertek Testing Services Shenzhen Ltd. Longhua Branch 101, 201, Building B, No. 308 Wuhe Avenue, Zhangkengjing Community, GuanHu Subdistrict, LongHua District, ShenZhen, P.R. China Tel / Fax: 86-755-8614 0680/86-755-8601 6661 Intertek Report No.: 210519017SZN-001 Version: 01-November-2017 Page: 3 of 23 FCC ID 249_C Test Report Table of Contents 1.0 Summary of Test Result ................................................................................................. 4 2.0 General Description ...................................................................................................... 5 2.1 Product Description .................................................................................................... 5 2.2 Related Submittal(s) Grants ......................................................................................... 5 2.3 Test Methodology ...................................................................................................... 5 2.4 Test Facility ............................................................................................................... 5 3.0 System Test Configuration ............................................................................................. 6 3.1 Justification ............................................................................................................... 6 3.2 EUT Exercising Software .............................................................................................. 6 3.3 Special Accessories ..................................................................................................... 6 3.4 Equipment Modification .............................................................................................. 6 3.5 Measurement Uncertainty .......................................................................................... 7 3.6 Support Equipment List and Description ........................................................................ 7 4.0 Emission Results ........................................................................................................... 8 4.1 Radiated Test Results .................................................................................................. 8 4.1.1 Field Strength Calculation ......................................................................................... 8 4.1.2 Radiated Emission Configuration Photograph .............................................................. 9 4.1.3 Radiated Emissions .................................................................................................. 9 4.1.4 Transmitter Spurious Emissions ............................................................................... 12 5.0 Equipment Photographs .............................................................................................. 16 6.0 Product Labelling ........................................................................................................ 16 7.0 Technical Specifications ............................................................................................... 16 8.0 Instruction Manual ..................................................................................................... 16 9.0 Miscellaneous Information .....................................................…

Text truncated - open the document above for the full version.

Radiated photos The EUT was placed at the center of turntable The EUT was placed at the center of turntable