2ALB6-PALMBLE04Remote control

PALI M4 remote control Take Off Guide 1. Pali M4 Remote Control 2. Turn On Pali M4 Pali M4 remote control arrives with a 2 AAA batteries blister inside a polybag. To turn on your Pali M4 remote control, please follow the instructions below. 1. Turn ON your TV and your Set Top Box. 2. Remove your Pali M4 remote control and its batteries from the plastic bag. 3. Remove the remote’s battery lid. 4. Place the batteries on the Pali M4 remote control as indicated in the image above and replace the battery lid. 5. After inserting the batteries, wait a few seconds and the Pali M4 remote will be ready to operate the Set-Top-Box. FCC Compliance Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televison reception, which can be determinated by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. .Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation expuser limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

T. +351 256 001 930 www.tech4home.pt NIF. 509 195 830 [email protected] Centro Empresarial e Tecnológico de S. João da Madeira Rua de Fundões, nº 151 3700-121 S. João da Madeira Portugal Date: 08/10/2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2ALB6-PALMBLE04 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Tech4home, Lda This authorization is valid until further written notice from the applicant. Print Name: Miguel Valente Title: Total Quality Manager Signature: On behalf of Company: Tech4home, Lda Telephone: +351256001930 E-mail: [email protected]

T. +351 256 001 930 www.tech4home.pt NIF. 509 195 830 [email protected] Centro Empresarial e Tecnológico de S. João da Madeira Rua de Fundões, nº 151 3700-121 S. João da Madeira Portugal To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Tech4home, Lda Rua de Fundoes, No.151, 3700-121 Sao João da Madeira, Portugal Regarding: Confidentiality Request regarding application for FCC ID: 2ALB6-PALMBLE04 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Miguel Valente Title: Total Quality Manager Signature:(08/19/2020) On behalf of Company: Tech4home, Lda Telephone: +351256001930 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 External Photos for SZEM2008007620CR FCC ID: 2ALB6-PALMBLE04 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4

T. +351 256 001 930 w ww.tech4home.pt NI F. 509 195 830 gera [email protected] Cen tro Empresarial e Tecnológico de S. João da Madeira Ru a de Fundões, nº 151 3 700-121 S. João da Madeira Portugal F CC Label Artwork Each equipment covered in the certification for equipment authorization shall bear a label listing as the following: 1)An FCC ID, which should be printed in the following format with legible lettering. Eight point type is acceptable. FCC ID: 2ALB6-PALMBLE04 “FCC ID” - in capital letters on a single line. 2ALB6 - grantee code as assigned by the FCC (may be three or five). PALMBLE04 - alphanumeric characters selected specific to this product 2 )Label artwork (for products such as RF remote controller / receiver) FCC ID: 2ALB6-PALMBLE04 Note 1: The FCC ID is laser printed on the battery compartment. Note 2: The label shall not be a stick-on paper label. The label on these products shall be permanently affixed to the product and shall be readily visible to the purchaser at the time of purchase. “Permanently affixed” means that the label is etched, engraved, stamped, silkscreened, indelibly printed, or otherwise permanently marked on a permanently attached part of the equipment or on a nameplate of metal, plastic, or other material fastened to the equipment by welding, riveting, or a permanent adhesive. The label must be designed to last the expected lifetime of the equipment in the environment in which the equipment may be operated and must not be readily detachable.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Internal Photos for SZEM2008007620CR FCC ID: 2ALB6-PALMBLE04 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762003 Page: 1 of 6 Keny Xu EMC Laboratory Manager 1 Cover page SAR Evaluation Report Application No.: SZEM2008007620CR Applicant: Tech4home, Lda Address of Applicant: Rua de Fundoes, No.151, 3700-121 Sao Joao da Madeira, Portugal Manufacturer: Guangdong Seneasy Intelligent Technology Co., Ltd Address of Manufacturer: 63, Huitai Industrial Park, Huicheng District, Huizhou Factory: Guangdong Seneasy Intelligent Technology Co., Ltd Address of Factory: 63, Huitai Industrial Park, Huicheng District, Huizhou Equipment Under Test (EUT): EUT Name: Remote control Model No.: T4HU2001/ 35k, T4HU2031/ 35k, PALMBLE04, Pali M4 BLE   Please refer to section 1.1 of this report which indicates which item was actually tested and which were electrically identical. FCC ID: 2ALB6-PALMBLE04 Standards: 47 CFR Part 1.1307 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2020-08-07 Date of Test: 2020-08-08 to 2020-08-14 Date of Issue: 2020-08-21 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762003 Page: 2 of 6 2 Version Revision Record Version Chapter Date Modifier Remark 01 2020-08-21 Original Authorized for issue by: Gebin Sun /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762003 Page: 3 of 6 3 Contents Page 1 COVER PAGE .............................................................................................................................................. 1 2 VERSION ...................................................................................................................................................... 2 3 CONTENTS .................................................................................................................................................. 3 4 GENERAL INFORMATION .......................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF EUT ............................................................................................................. 4 4.2 TEST LOCATION ...................................................................................................................................... 5 4.3 TEST FACILITY ........................................................................................................................................ 5 4.4 DEVIATION FROM STANDARDS ................................................................................................................. 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 5 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 5 5 SAR EVALUATION ...................................................................................................................................... 6 5.1 RF EXPOSURE COMPLIANCE REQUIREMENT ............................................................................................ 6 5.1.1 Standard Requirement ..................................................................................................................... 6 5.1.2 Limits ................................................................................................................................................ 6 5.1.3 EUT RF Exposure ............................................................................................................................ 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762003 Page: 4 of 6 4 General Information 4.1 General Description of EUT Power Supply: 3V DC(1.5V x 2 "AAA" Size Batteries) Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: BLE V4.2 Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: Integral Antenna Gain: 0dBi Remark: Model No.: T4HU2001/ 35k, T4HU2031/ 35k, PALMBLE04, Pali M4 BLE Only the model T4HU2001/35k was tested. According to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on names due to different buyers or other cosmetic changes (print colors, logos, etc). SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762003 Page: 5 of 6 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762002 Page: 1 of 48 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM2008007620CR Applicant: Tech4home, Lda Address of Applicant: Rua de Fundoes, No.151, 3700-121 Sao Joao da Madeira, Portugal Manufacturer: Guangdong Seneasy Intelligent Technology Co., Ltd Address of Manufacturer: 63, Huitai Industrial Park, Huicheng District, Huizhou Factory: Guangdong Seneasy Intelligent Technology Co., Ltd Address of Factory: 63, Huitai Industrial Park, Huicheng District, Huizhou Equipment Under Test (EUT): EUT Name: Remote control Model No.(EUT): T4HU2001/ 35k, T4HU2031/ 35k, PALMBLE04, Pali M4 BLE   Please refer to section 1.1 of this report which indicates which item was actually tested and which were electrically identical. FCC ID: 2ALB6-PALMBLE04 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2020-08-07 Date of Test: 2020-08-08 to 2020-08-14 Date of Issue: 2020-08-21 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762002 Page: 2 of 48 Revision Record Version Chapter Date Modifier Remark 01 2020-08-21 Original Authorized for issue by: Gebin Sun /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762002 Page: 3 of 48 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Minimum 6dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Power Spectrum Density 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Remark: Model No.: T4HU2001/ 35k, T4HU2031/ 35k, PALMBLE04, Pali M4 BLE Only the model T4HU2001/35k was tested. According to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on names due to different buyers or other cosmetic changes (print colors, logos, etc). SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200800762002 Page: 4 of 48 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 6 4.4 TEST LOCATION .................................................................................................................................... 7 4.5 TEST FACILITY ...................................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 7 5 EQUIPMENT LIST ...................................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 12 6.1 ANTENNA REQUIREMENT .................................................................................................................... 12 6.1.1 Test Requirement: ....................................................................................................................... 12 6.1.2 Conclusion ................................................................................................................................... 12 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 13 7.1 MINIMUM 6DB BANDWIDTH .................................................................................................................. 13 7.1.1 E.U.T. Operation .......................................................................................................................... …

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZEM2008007620CR FCC ID: 2ALB6-PALMBLE04 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs 1.1 Radiated Emissions which fall in the restricted bands Test Setup SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 1.2 Radiated Spurious Emissions Test Setup