2ANFN-24050510W Bamboo Phone Stand & Wireless Charger

Manual for disassembly of bracket wireless charging Thank you for using this product Please read this manual carefully before use to ensure safe and correct use Product Image: Product parameters: Enter: DC5V/2A|DC9V/1.67A OutputDC9V/1A,7.5V/1A,5V/ 1A Frequency Range: 110-205kHz Wireless Power:Max 10W How to： 1. cross-stitch the ones and twos in the picture; 2. Connect the MICROUSB cable to the MICROUSB port on the wireless charger and connect the other end of the cable to the USB port or the USBAC adapter (which uses the QC3.0 or PD protocol adapter), with a red light indicating that the charger is properly connected and ready to use; 3. Place the device on a wireless charger and make sure it is in a central position; 4. When it is properly charged, the charger indicator lights up blue; Points to note: 1. Keep the charger away from water or other liquids. 2. If you need to clean the charger; make sure it is not connected to the power supply. 3. The ambient temperature for use is approximately 0-40oC. 4. . If your phone has a protective case, you may need to remove it to successfully connect when using a wireless charger. 5. When a non-rechargeable device is placed on the wireless charger; the FDO protection function is triggered, and the indicator light flickers, unable to work properly. 6. When the charging temperature is higher than 60 ° C, the NTC protection function is triggered, and the indicator lamp flickers andean not work normally. / Certificate of \ / Conformity \ Production date Inspector NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Warning Statements: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

Anhui Inno-Sign International Co., Ltd Agent Authorization Company: Anhui Inno-Sign International Co., Ltd Address: Room 1409-1410, Building B, Sky Blue Business Center, No.188 South Qianshan Road, Hefei, Anhui ,China Product Name: 10W Bamboo Phone Stand & Wireless Charger Model Number(s): 240505 Product Description: 10W Bamboo Phone Stand & Wireless Charger We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2022-07-27 Name: Linda Mei Company: Anhui Inno-Sign International Co., Ltd

Report No.: AGC05794220701AP02 Page 1 of 4 EXTERNAL PHOTOS All VIEW OF EUT TOP VIEW OF EUT Report No.: AGC05794220701AP02 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC05794220701AP02 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC05794220701AP02 Page 4 of 4 RIGHT VIEW OF EUT ****************************************End of Report****************************************

FCC ID Label Location 40mm&40mm FCC ID: 2ANFN-240505

Report No.: AGC05794220701AP02 Page 1 of 3 INTERNAL PHOTOS OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC05794220701AP02 Page 2 of 3 OPEN VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 1) Primary coil Antenna Secondary coil Antenna Report No.: AGC05794220701AP02 Page 3 of 3 INTERNAL VIEW OF EUT (FIGURE 2) ****************************************End of Report****************************************

Page 1 of 12 RF Exposure Report Report No.: AGC05794220701FH01 FCC ID : 2ANFN-240505 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : 10W Bamboo Phone Stand & Wireless Charger BRAND NAME : N/A MODEL NAME : 240505 APPLICANT : Anhui Inno-Sign International Co., Ltd DATE OF ISSUE : Jul. 26, 2022 STANDARD(S) : KDB680106 D01 RF Exposure Wireless Charging Base App v03r01 REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC05794220701FH01 Page 2 of 12 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 26, 2022 Valid Initial Release Report No.: AGC05794220701FH01 Page 3 of 12 TABLE OF CONTENTS 1. GENERAL INFORMATION .............................................................................................................................. 4 2. PRODUCT INFORMATION .............................................................................................................................. 5 2.1 PRODUCT TECHNICAL DESCRIPTION ................................................................................................ 5 2.2 TEST FREQUENCY LIST ........................................................................................................................ 5 3. TEST ENVIRONMENT ..................................................................................................................................... 6 3.1 ADDRESS OF THE TEST LABORATORY .............................................................................................. 6 3.2 TEST FACILITY ....................................................................................................................................... 6 3.3 ENVIRONMENTAL CONDITIONS........................................................................................................... 7 3.4 MEASUREMENT UNCERTAINTY .......................................................................................................... 7 3.5 LIST OF EQUIPMENTS USED ............................................................................................................... 7 4. EQUIPMENT USED IN TESTED SYSTEM ...................................................................................................... 8 5. DESCRIPTION OF TEST MODES ................................................................................................................... 8 6. RF EXPOSURE MEASUREMENT ................................................................................................................... 9 6.1 REFER EVALUATION METHOD ............................................................................................................. 9 6.2 TEST LIMITS ........................................................................................................................................... 9 6.3 MEASUREMENT SETUP ...................................................................................................................... 10 6.4 MEASUREMENT PROCEDURE ........................................................................................................... 11 6.4 MEASUREMENT RESULTS.................................................................................................................. 11 APPENDIX I: PHOTOGRAPHS OF TEST SETUP ............................................................................................ 12 Report No.: AGC05794220701FH01 Page 4 of 12 1. GENERAL INFORMATION Applicant Anhui Inno-Sign International Co., Ltd Address Room 1409-1410, Building B, Sky Blue Business Center, No.188 South Qianshan Road, Hefei, Anhui, China Manufacturer Shenzhen Unite Creation Co., Ltd (Dongguan Branch) Address No.37, Foaosan Street, Xiniupo, Dalang Town, Dongguan City, Guangdong Province, China Factory Shenzhen Unite Creation Co., Ltd (Dongguan Branch) Address No.37, Foaosan Street, Xiniupo, Dalang Town, Dongguan City, Guangdong Province, China Product Designation 10W Bamboo Phone Stand & Wireless Charger Brand Name N/A Test Model 240505 Deviation from Standard No any deviation from the test method Date of Test Jul. 14, 2022 – Jul. 26, 2022 Test Result Pass Prepared By Bibo Zhang (Project Engineer) Jul. 26, 2022 Reviewed By Calvin Liu (Reviewer) Jul. 26, 2022 Approved By Max Zhang (Authorized Officer) Jul. 26, 2022 Report No.: AGC05794220701FH01 Page 5 of 12 2. PRODUCT INFORMATION 2.1 PRODUCT TECHNICAL DESCRIPTION Equipment Specification WPT Operation Frequency 110.1-205KHz Hardware Version S7-V13-T2.0 Software Version D52F1F Modulation Type ASK Number of channels 1 Field Strength of Fundamental 84.29dBuV/m (Max) Antenna Designation Coil Antenna Antenna Gain 0dBi Power Supply Enter: DC5V/2A|DC9V/1.67A OutputDC9V/1A, 7.5V/1A, 5V/1A Wireless Power: Max 10W Adapter Information N/A 2.2 TEST FREQUENCY LIST Frequency Band Channel Number Test Frequency 110.1KHz-205KHz 01 110.5 KHz Report No.: AGC05794220701FH01 Page 6 of 12 3. TEST ENVIRONMENT 3.1 ADDRESS OF THE TEST LABORATORY Laboratory: Attestation of Global Compliance (Shenzhen) Co., Ltd. Address: 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China 3.2 TEST FACILITY The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5488 Attestation of Global Compliance (Shenzhen) Co., Ltd. has been assessed and proved to be in compliance with CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2017 General Requirements) for the Competence of Testing and Calibration Laboratories. A2LA-Lab Cert. No.: 5054.02 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirement…

Text truncated - open the document above for the full version.

Anhui Inno-Sign International Co., Ltd Declaration Letter Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 7/28/2022 FCC ID: 2ANFN-240505 Pursuant to KDB 680106 of the Anhui Inno-Sign International Co., Ltd hereby declare our product which is an inductive wireless power transfer applications that meet all of the following requirements are not required to submit a KDB inquiry for devices approved usinga PAG for equipment approved using certification to address RF exposure compliance. 1) Power transfer frequency is 0.1101-0.205MHz which is less than1 MHz 2) Output power from each primary coil is 10W which is less than 10 watts 3) The transfer system includes only single primary and secondary coils. 4) Client device is placed directly in contact with the transmitter 5) The EUT is a mobile device. 6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Yours sincerely, Anhui Inno-Sign International Co., Ltd Contact person: Linda Mei

Page 1 of 30 FCC Test Report Report No.: AGC05794220701FE10 FCC ID : 2ANFN-240505 APPLICATION PURPOSE Original Equipment PRODUCT DESIGNATION : 10W Bamboo Phone Stand & Wireless Charger BRAND NAME : N/A MODEL NAME : 240505 APPLICANT : Anhui Inno-Sign International Co., Ltd DATE OF ISSUE : Jul. 26, 2022 STANDARD(S) : FCC Part 15 Subpart C REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC05794220701FE10 Page 2 of 30 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 26, 2022 Valid Initial Release Report No.: AGC05794220701FE10 Page 3 of 30 TABLE OF CONTENTS 1. GENERAL INFORMATION .............................................................................................................................. 5 2. PRODUCT INFORMATION .............................................................................................................................. 6 2.1 PRODUCT TECHNICAL DESCRIPTION ................................................................................................ 6 2.2 TEST FREQUENCY LIST ........................................................................................................................ 6 2.3 RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................. 7 2.4 TEST METHODOLOGY .......................................................................................................................... 7 2.5 SPECIAL ACCESSORIES ....................................................................................................................... 7 2.6 EQUIPMENT MODIFICATIONS .............................................................................................................. 7 2.7 ANTENNA REQUIREMENT .................................................................................................................... 7 3. TEST ENVIRONMENT ..................................................................................................................................... 8 3.1 ADDRESS OF THE TEST LABORATORY .............................................................................................. 8 3.2 TEST FACILITY ....................................................................................................................................... 8 3.3 ENVIRONMENTAL CONDITIONS........................................................................................................... 9 3.4 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 3.5 LIST OF EQUIPMENTS USED ............................................................................................................. 10 4.SYSTEM TEST CONFIGURATION ................................................................................................................. 11 4.1 EUT CONFIGURATION ......................................................................................................................... 11 4.2 EUT EXERCISE ..................................................................................................................................... 11 4.3 CONFIGURATION OF TESTED SYSTEM ............................................................................................ 11 4.4 EQUIPMENT USED IN TESTED SYSTEM........................................................................................... 11 4.5 SUMMARY OF TEST RESULTS ........................................................................................................... 12 5. DESCRIPTION OF TEST MODES ................................................................................................................. 13 6. RADIATED SPURIOUS EMISSION ............................................................................................................... 14 6.1 PROVISIONS APPLICABLE .................................................................................................................. 14 6.3 FIELD STRENGTH CALCULATION ...................................................................................................... 16 6.4 MEASUREMENT SETUP (BLOCK DIAGRAM OF CONFIGURATION) ............................................... 17 6.5 MEASUREMENT RESULTS.................................................................................................................. 18 7. 20 DB BANDWIDTH ....................................................................................................................................... 24 7.1 PROVISIONS APPLICABLE .................................................................................................................. 24 7.2 MEASUREMENT PROCEDURE ........................................................................................................... 24 7.3 MEASUREMENT SETUP (BLOCK DIAGRAM OF CONFIGURATION) ............................................... 24 7.4 MEASUREMENT RESULTS.................................................................................................................. 25 8. AC POWER LINE CONDUCTED EMISSION TEST ...................................................................................... 26 8.1 LIMITS OF LINE CONDUCTED EMISSION TEST ............................................................................... 26 8.2 MEASUREMENT SETUP (BLOCK DIAGRAM OF CONFIGURATION) ............................................... 26 Report No.: AGC05794220701FE10 Page 4 of 30 8.3 PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST .......................................... 27 8.4 FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST ........................................................ 27 8.5 MEASUREMENT RESULTS.................................................................................................................. 27 APPENDIX I: PHOTOGRAPHS OF TEST SETUP ..............................................…

Text truncated - open the document above for the full version.

Report No.: AGC05794220701AP01 Page 1 of 4 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 30MHz RADIATED EMISSION TEST SETUP BELOW 1GHz Report No.: AGC05794220701AP01 Page 2 of 4 AC POWER LINE CONDUCTED TEST SETUP RF EXPOSURE TEST SETUP Position E Report No.: AGC05794220701AP01 Page 3 of 4 Position A Position B Report No.: AGC05794220701AP01 Page 4 of 4 Position C Position D ****************************************End of Report*************************************