2ANX3-ELT01LoRa device

Operating manual Publish Date: 2023-XX-XX v1.0 Wireless sensor ElektronikSystem i Umeå AB Tvistevägen 48C, 90736 Umeå, Sweden E-mail: [email protected] ǀ Web: www.elsys.se Specifications in this document are subject to change without notice. ©ElektronikSystem i Umeå AB 2022 Operating manual ELT series Operating manual ELT series ElektronikSystem i Umeå AB Tvistevägen 48C, 90736 Umeå, Sweden E-mail: [email protected] ǀ Web: www.elsys.se Important safety information Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, ElektronikSystem i Umeå AB will not be held responsible for any loss or damage resulting from not following the instructions of this operating manual. • The device must not be dismantled or modified in any way. • The device is not intended to be used as a reference sensor, and ElektronikSystem i Umeå AB will not be held liable for any damage which may result from inaccurate readings. • The battery should be removed from the device if it is not to be used for an extended period. Otherwise, the battery might leak and damage the device. Never leave a discharged battery in the battery compartment. • The device must never be subjected to shocks or impacts. • To clean the device, wipe with a soft moistened cloth. Use another soft, dry cloth to wipe dry. Do not use any detergent or alcohol to clean the device. Disposal note in accordance with Waste from Electrical and Electronic Equipment (WEEE) Directive 2012/19/EU The device, as well as all the individual parts, must not be disposed of with household waste or industrial waste. You are obliged to dispose of the device at the end of its service life in accordance with the requirements of RoHS 2012/19/EU to protect the environment and to reduce waste through recycling. For additional information and how to carry out disposal, please contact the certified disposal service providers. The sensors contain a lithium battery, which must be disposed of separately. Operating manual ELT series ElektronikSystem i Umeå AB Tvistevägen 48C, 90736 Umeå, Sweden E-mail: [email protected] ǀ Web: www.elsys.se Contents 1. Product information .................................................................................... 1 1.1 Description ........................................................................................ 1 1.2 ELT Series attributes ......................................................................... 1 1.3 Label ................................................................................................. 1 1.4 Dimensions (mm) ............................................................................. 2 1.5 Main features of the ELT series ......................................................... 3 2. Mounting guidelines ................................................................................... 4 2.1 Ultrasonic and Snow ......................................................................... 4 3. Installation .................................................................................................. 5 3.1 NFC Configuration ............................................................................. 6 3.2 Over the air configuration .................................................................. 7 3.3 Application parameters ...................................................................... 7 4. Sensor behavior ......................................................................................... 8 4.1 Sensor startup .................................................................................. 8 4.2 Sampling mode / Periodic measurement ........................................... 8 4.3 Scheduled transmission .................................................................... 8 4.4 LED indication ................................................................................... 9 5. Internal sensors ........................................................................................ 10 5.1 Temperature ................................................................................... 11 5.2 Humidity ......................................................................................... 11 5.3 Atmospheric Pressure ..................................................................... 12 5.4 Accelerometer ................................................................................. 12 Operating manual ELT series ElektronikSystem i Umeå AB Tvistevägen 48C, 90736 Umeå, Sweden E-mail: [email protected] ǀ Web: www.elsys.se 6 External Sensors....................................................................................... 14 7 Device specifications ................................................................................ 15 8 Sensor payload format ............................................................................. 16 9 Regulations............................................................................................... 16 a. Legal Notices ...................................................................................... 16 b. Declaration of conformity .................................................................... 16 c. Federal Communication Commission Interference Statement .............. 16 10 Revision History ................................................................................... 18 Operating manual ELT series 1 ElektronikSystem i Umeå AB Tvistevägen 48C, 90736 Umeå, Sweden E-mail: [email protected] ǀ Web: www.elsys.se 1. Product information 1.1 Description The ELT series of sensors are universal LoRaWAN ® industrial sensors for both in- and outdoor use. The internal sensors measure, depending on model, temperature, humidity, atmospheric pressure, distance, and acceleration. The ELT series are also equipped with multi-purpose I/O for connection to external sensors and equipment. The sensors are equipped with NFC…

Text truncated - open the document above for the full version.

CONFIDENTIA LIT Y REQUEST fo r Certif ication Service in USA Fede ral Commun ication Commission Equ ipment Autho riza tion Divisi on , App lication Processing Bran ch 74 35 Oaklan d Mills Roa d Col umbia, MD 21 04 8 September 27, 20 24 TO WHOM IT MAY CONCERN Pursuant to Paragrap hs §0 .45 7 an d 0.45 9 of the Commission ’s Rul es (47 C.F.R.) an d Section §5 52 (b)(4) of the Freedom of Infor mation Act , we req ue st s confide ntialit y for the fol lowing products: FCC ID Mod el na me 2ANX03-ELT01 ELT se ri es For the prod uct st ated ab ove, we req ue st pe rman en t confide ntial ity for exhibi ts whi ch contai n Ope ration al Des cr iption, Block Diagram, Schematics, Parts Li sts or Tune Up Information . The ab ove exhibi ts contai n our trad e secrets an d proprietary infor mation tha t cou ld be of be ne fit to our competitor s. If you ha ve any qu es tion s, pl ea se fee l free to contact me at the ad dress sho wn below. Sincerel y, Name: Peter Björk Company: El ektron iks ystem I Umeå AB Add ress: Tvist eväge n 48 , 90 73 6, Umeå Pho ne : +4690-100500 Email: peter.bjork@elsy s.se

Annex A101 - Photographs No.1-7227-23-01-01_TR1-A101-R01 September 24, 2024 DescriptionExternal photographs of EUT This document is electronically signed and valid without handwritten signature. Public keys for verification of the electronic signatures can be requested at the testing laboratory. Authorized Hans-Joachim Wolsdorfer Lab Manager Radio Labs cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A101-R01 Release 1 - Page 1 of 4 Photo 1 Photo 2 cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A101-R01 Release 1 - Page 2 of 4 Photo 3 Photo 4 cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A101-R01 Release 1 - Page 3 of 4 Photo 5 Photo 6 - END OF DOCUMENT - cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A101-R01 Release 1 - Page 4 of 4

Internal and external photos, label location ELT series External difference is in label and cable gland ELT series with antenna ELT lite top ELT 2 top FCC ID 2ANX3-ELT01 IC ID: 26904-ELT01 ELT lite bottom, label location ELT 2 bottom, label location ELT lite back ELT 2 back ELT series front ELT 2 internal Difference on ELT lite compared to ELT2 Left pic: 3 pin connector instead of 4 pin and unpopulated components in red oval (for missing I/O 2). Right pic: Unpopulated internal sensors in red circle. (Populated in pic)

Annex A102 - Photographs No.1-7227-23-01-01_TR1-A102-R01 September 24, 2024 DescriptionInternal photographs of EUT This document is electronically signed and valid without handwritten signature. Public keys for verification of the electronic signatures can be requested at the testing laboratory. Authorized Hans-Joachim Wolsdorfer Lab Manager Radio Labs cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A102-R01 Release 1 - Page 1 of 3 Photo 1 Photo 2 cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A102-R01 Release 1 - Page 2 of 3 Photo 3 - END OF DOCUMENT - cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A102-R01 Release 1 - Page 3 of 3

© cetecom advanced GmbH Page 1 of 12 TEST REPORT Test report no.: 1-7227-23-01-04_TR1-R02 Testing laboratory Applicant cetecom advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://cetecomadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS). The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12047-01-00. ISED Testing Laboratory Recognized Listing Number: DE0001 FCC designation number: DE0002 Elektroniksystem i Umeå AB Tvistevägen 48 90736 Umeå / SWEDEN Phone: +46 901 00500 Contact: Johan Haake e-mail: [email protected] Manufacturer Elektroniksystem i Umeå AB Tvistevägen 48 90736 Umeå / SWEDEN Test Item Kind of test item: LoRa Device Model name: ELT lite, ELT 2 FCC ID: 2ANX3-ELT01 Frequency: 902-928 MHz Technology tested: LoRa This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: Alexander Hnatovskiy Eric Tuettmann Lab Manager Testing Manager Radio Labs Radio Labs Test report no.: 1-7227-23-01-04_TR1-R02 © cetecom advanced GmbH Page 2 of 12 1 Table of contents 1 Table of contents ............................................................................................................................................. 2 2 General Information ......................................................................................................................................... 3 2.1 Notes and Disclaimer ............................................................................................................................ 3 2.2 References ............................................................................................................................................ 3 2.3 Structure of this Document ................................................................................................................... 3 3 General RF Exposure Test Exemptions ............................................................................................................ 4 3.1 1 mW Test Exemption ........................................................................................................................... 5 3.2 MPE-Based Test Exemption ................................................................................................................. 5 3.3 SAR-Based Test Exemption .................................................................................................................. 5 3.4 Simultaneous Transmission ............................................................................................................... 6 4 1 mW Test Exemption ...................................................................................................................................... 7 4.1 Detailed Description .............................................................................................................................. 7 4.2 Results ................................................................................................................................................... 7 5 MPE-Based Test Exemption ............................................................................................................................ 8 5.1 Detailed Description .............................................................................................................................. 8 5.2 Results ................................................................................................................................................... 9 6 SAR-Based Test Exemption ........................................................................................................................... 10 6.1 Detailed Description ............................................................................................................................ 10 6.2 Results ................................................................................................................................................. 10 7 Simultaneous Transmission .......................................................................................................................... 11 7.1 Detailed Description ............................................................................................................................ 11 7.2 Result................................................................................................................................................... 11 8 Conclusion ...................................................................................................................................................... 12 Annex A: Document History .......................................................................................................................... 12 Test report no.: 1-7227-23-01-04_TR1-R02 © cetecom advanced GmbH Page 3 of 12 2 General Information 2.1 Notes and Disclaimer The test results of this test report relate exclusively to the test item specified in this test report. cetecom advanced GmbH does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of cetecom advanced GmbH. The testing service provided by cetecom advanced GmbH has been rendered under the current "General Terms and Conditions for cetecom advanced GmbH". ce…

Text truncated - open the document above for the full version.

AMEISONCOMMUNICATIONEQUIPMENTCO.,LTD. HongKongheadoffice: FOXTENNACOMMUNICATIONLIMITED ChinaFactory:33-2#,FajiafuIndustrialZone,Shantangwei,Pingdi,Longgang,Shenzhen,518117,P.R.China. Tel:86–755-89914346Fax:86-755-89914746 Website: http://www.ameison.cc 915MHzRubberDuckWhipTerminalAntenna AMXT-900-3 Features: Highgain，stronganti-interferenceability Fulldayworking Exquisiteappearance Optimizeddimension Applications: Applicabletoterminals CanbeaddedtowirelessLAN,USBadapterorrouter,AccessPointConverage AMXT-900-3 ElectricalSpecifications Frequencyrange(MHz) 902-928 Bandwidth(MHz)26 Gain(dBi)3 VSWR≤2.0 InputImpedance(Ω)50 PolarizationVertical Maximuminputpower(W)50 InputconnectortypeSMAMaleorRequested MechanicalSpecifications Dimensions(mm) Φ13.5x210 Antennaweight(g)20 RadomecolorBlack Operatingtemperature(°c) -40～60

BNetzA - CAB - 02/21 - 102 TEST REPORT Test report no.: 1-7227_23-01-03 Testing laboratory Applicant cetecom advanced GmbH Untertuerkheimer Strasse 6 – 10 66117 Saarbruecken / Germany Phone: + 49 681 5 98 - 0 Fax: + 49 681 5 98 - 9075 Internet: https://cetecomadvanced.com e-mail: [email protected] Accredited Testing Laboratory: The testing laboratory (area of testing) is accredited according to DIN EN ISO/IEC 17025 (2018-03) by the Deutsche Akkreditierungsstelle GmbH (DAkkS). The accreditation is valid for the scope of testing procedures as stated in the accreditation certificate with the registration number: D-PL-12047-01-00. ISED Testing Laboratory Recognized Listing Number: DE0001 FCC designation number: DE0002 Elektroniksystem i Umeå AB Tvistevägen 48 90736 Umeå / SWEDEN Phone: +46 901 00500 Contact: Johan Haake e-mail: [email protected] Manufacturer Elektroniksystem i Umeå AB Tvistevägen 48 90736 Umeå / SWEDEN Test standard/s FCC - Title 47 CFR Part 15 FCC - Title 47 of the Code of Federal Regulations; Chapter I; Part 15 - Radio frequency devices RSS - 247 Issue 3 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices For further applied test standards please refer to section 3 of this test report. Test Item Kind of test item: LoRa device Model name: ELT lite, ELT 2 FCC ID: 2ANX3-ELT01 ISED certification number: 26904-ELT01 Frequency: 902.0 MHz – 928.0 MHz Technology tested: LoRa Antenna: external antenna (RP-SMA connector Power supply: 3.2 V to 3.7 V DC by battery Temperature range: -20°C to +55°C This test report is electronically signed and valid without handwritten signature. For verification of the electronic signatures, the public keys can be requested at the testing laboratory. Test report authorized: Test performed: Christoph Schneider Hans-Joachim Wolsdorfer Lab Manager Lab Manager Radio Labs Radio Labs Test report no.: 1-7227_23-01-03 © cetecom advanced GmbH Page 2 of 49 1 Table of contents 1 Table of contents ....................................................................................................................................... 2 2 General information ................................................................................................................................... 3 2.1 Notes and disclaimer ...................................................................................................................... 3 2.2 Application details .......................................................................................................................... 3 2.3 Test laboratories sub-contracted .................................................................................................... 3 3 Test standard/s, references and accreditations ......................................................................................... 4 4 Reporting statements of conformity – decision rule .................................................................................. 5 5 Test environment ....................................................................................................................................... 6 6 Test item ................................................................................................................................................... 6 6.1 General description ......................................................................................................................... 6 6.2 Additional information .................................................................................................................... 6 7 Description of the test setup ...................................................................................................................... 7 7.1 Shielded semi anechoic chamber .................................................................................................... 8 7.2 Shielded fully anechoic chamber ................................................................................................... 10 7.3 Conducted measurements ............................................................................................................ 11 8 Sequence of testing ................................................................................................................................. 12 8.1 Sequence of testing radiated spurious 9 kHz to 30 MHz ............................................................... 12 8.2 Sequence of testing radiated spurious 30 MHz to 1 GHz ............................................................... 13 8.3 Sequence of testing radiated spurious 1 GHz to 10 GHz................................................................ 14 9 Measurement uncertainty ........................................................................................................................ 15 10 Additional comments ........................................................................................................................... 16 11 Summary of measurement results ....................................................................................................... 17 12 Measurement results ........................................................................................................................... 18 12.1 Maximum output power ............................................................................................................. 18 12.2 Antenna gain ............................................................................................................................. 21 12.3 Power spectral density .............................................................................................................. 22 12.4 Spectrum bandwidth – 6 dB bandwidth and 99% bandwidth ...................................................... 25 12.5 Detailed spurious emissions @ the band edge – conducted and radiated .................................. 29…

Text truncated - open the document above for the full version.

Annex A103 - Photographs No.1-7227-23-01-01_TR1-A103-R01 September 23, 2024 DescriptionTest set-up photographs This document is electronically signed and valid without handwritten signature. Public keys for verification of the electronic signatures can be requested at the testing laboratory. Authorized Hans-Joachim Wolsdorfer Lab Manager Radio Labs cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A103-R01 Release 1 - Page 1 of 4 Photo 1 Photo 2 cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A103-R01 Release 1 - Page 2 of 4 Photo 3 Photo 4 cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A103-R01 Release 1 - Page 3 of 4 Photo 5 - END OF DOCUMENT - cetecom advanced GmbH Untertürkheimer Str. 6-10, 66117 Saarbrücken Document No. 1-7227-23-01-01_TR1-A103-R01 Release 1 - Page 4 of 4