2AO23-BTSP22Portable Wireless Radio

wireless retro speaker NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Target Corp. Mpls. MN, 55403 Phone: 612-304-6073 For qualied repair specialists requesting repair information and parts please contact the original manufacturer at customersupport@gemsndyours.com Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. FCC ID: 2AO23-BTSP22 Model: BTSP22 Input: 5V 1A Made in China This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. sidefr ont M SW SW AM FM MHz KHz MHz AM FM BT OFFON press - pre. t rack press - next. track press - play/pause power on/off vol. - /+ control USB TF AUX CHARGE DC 5V aux port charging port/ USB-C port charging indicator microSD card slot USB-A port (for USB ash disk) antenna mode selection Bluetooth indicator station tuning • Three Rapid Tones - Ready to pair • Single Chime - Paired • Two Rapid Dings - Low battery radio function • Switch Bands: Turn the left knob to cycle through SW (Shortwave), AM, FM • Tune In: Rotate the large front dial to nd your favorite station • Pull out the telescopic antenna fully for clearer reception—this works great for FM and SW signals media playback • USB/TF Card: Plug a USB drive into the USB port or insert a TF (Micro SD) card into the TF slot The speaker will play audio les from the device when using the “M” button to switch • AUX Input: Use a 3.5mm audio cable to connect your media source to the AUX port charging • Full charge requires approximately 3 hours • Charging is complete when charging indicator red light turns off • Plug USB-C end of charging cable into side of speaker • Plug USB-A end of charging cable into a power supply of at least DC 5V 1A Warning: please use UL compliant power supply troubleshooting • If the speaker is not working correctly, turn it on/off to restart • If the speaker won’t turn on, recharge the battery and try again • If the speaker won’t charge, make sure the supply works, is 5V 1A, and not damaged • If the speaker makes no sound or does not show as an available device, make sure it is not paired to other devices, if so unpair the device and repair the desired device • Radio Has Static? Extend the antenna all the way and try moving the speaker to an area with less interference (like away from Wi-Fi routers) safety • The speaker is splash resistant, do not submerge under water • Do not modify or repair this device • Do not use in high temperatures or extreme weather • Do not use chemical detergents to clean your device, use a soft dry cloth included • Wireless Retro Speaker • USB-C Charging Cable • 3.5mm AUX Cable Bluetooth Pairing Mode • Turn the right knob clockwise to power on • Turn the mode selector knob (left knob) to “BT”. The Bluetooth indicator will rapid ashing red light • Use Bluetooth settings on your phone to pair with H&H Retro • White light turns solid followed by a chime - pairing successful • Once paired, it will automatically connect next time you turn it on indicators Charging indicator: Solid Red - Charging No Red Light - Fully Charged Bluetooth indicator: Rapid Flashing Red - Pairing Mode Solid Red - Bluetooth Connected Slow Flashing Red - Play Music • Ascending Tones - Power on • Descending Tones - Power off hold - switch modes (Bluetooth/aux/USB/microSD card)

Chug, Inc. 7157 Shady Oak Rd, Eden Prairie MN 55344, United States 092723-17 rev 10 Certification Application Attestation Statements Date: March 14, 2026 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) ______Chug,Inc.______ certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) _____Chug,Inc.______ (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is /  - is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates – see KDB 986446 Question 5) as an entity producing “covered” equipment. The applicant also certifies that the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc or any of its successors and assignees identified on the covered list installed on the device, nor will it be installed by the applicant at any time after certification. Thank you, By: __________________________ ________Michael Clemmer__________ (Signature 2 ) (Print name) Title: ______general manager________ Company: _______Chug,Inc.________ Telephone: _____612-868-2191_ 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

Chug,Inc. 7157ShadyOakRd,EdenPrairieMN55344,UnitedStates 092723-17Rev9 U.S.AgentDesignationforServiceofProcess (ApplicantisBothGranteeandU.S.Agent) TO:AmericanCertificationBody,Inc. 313ParkAvenue Suite300 FallsChurch,VA22046 ATTENTION:FCCCertification–Section2.911(d)(7)Information ThisletteristoconfirmthattheApplicantwillalsoserveastheU.S.AgentforServiceof Processasrequiredby47CFR2.911(d)(7).TheApplicantacknowledgesthatthey mustmaintainanagentfornolessthanoneyearafterterminatingallmarketingand importationORtheconclusionofanyCommission-relatedproceedinginvolvingthe equipment.TheApplicantfurtheracknowledgestheirresponsibilitytoinformtheFCC whenevertheDesignatedU.S.Agentinformationchanges. Applicant Companyname:Chug,Inc. FRN#:0027222264 GranteeCode: 2AO23 ContactName:MichaelClemmer StreetAddress:7157ShadyOakRd,EdenPrairieMN55344,UnitedStates City/Province/Zip:Wshington,55344 TelephoneNo: 612-868-2191 Email:[email protected] ApplicantSignature 2 : Date:2025-10-13 Signedby(PrintedName/Title):MichaelClemmer,generalmanager 2 - Lettersmustbeplacedonappropriateletterhead.Thesigneefortheapplicantmustbeoneofthefollowing:Applicant(grantee) contactofrecordintheFCC’sauthorizationsystem,orauthorizedofficersoremployeeoftheapplicant(grantee).

Chug, Inc. 7157 Shady Oak Rd, Eden Prairie MN 55344, United States 050222-17 Authority to Act as Agent Date: March 14, 2026 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: ____Shenzhen UnionTrust Quality and Technology Co., Ltd.______ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____12 months__ By: __________________________ __________Michael Clemmer____ (Signature 1 ) (Print name) Title: __________general manager___ On behalf of: ___________Chug,Inc. (Company Name) Telephone: _612-868-2191_______ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Chug, Inc. 7157 Shady Oak Rd, Eden Prairie MN 55344, United States 050222-17 Request for Confidentiality Date: March 14, 2026 Subject: Confidentiality Request for: ____2AO23-BTSP22 Pursuant to FCC 47 CFR 0.457(d) and 0.459 and/or IC RSP-100, Section 12.4, the applicant requests that a part of the subject application(s) be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term --------------------------- External Photos ☐ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☐ Permanent Parts List & Placement/BOM ☐ Short Term ☐ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☐ Short Term --------------------------- Test Setup Photos ☐ Short Term ☐ Permanent * 1 User’s Manual ______Chug,Inc.______ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality for FCC Applications: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of __N/A__ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Short Term Confidentiality for Industry Canada Applications: Starting May 2022, ISED will recognize short term confidentiality on certain exhibits until the intended date of marketing. The applicant requests the exhibits selected above as short term confidential be withheld from public view until: (specify ISED expiration date / date of marketing) . Sincerely, By: ____________general manager_ Michael Clemmer (Signature/Title 2 ) (Print name) The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Page 1 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS EUT EXTERNAL PHOTOS EUT Photo EUT Photo Page 2 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo Page 3 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo Page 4 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo

26.5 mm 比例：1:1 12.8 mm 尺寸：26.5 X 12.8 mm 字体颜色：乳白色 工艺：移印 22.5 mm 22.5 mm 15.70 mm 比例：1:1 尺寸：45.6X 32.8mm 字体颜色：乳白色 工艺：移印 45.6 mm 32.8 mm

Page 1 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS EUT INTERNAL PHOTOS EUT Photo EUT Photo FM Ant Page 2 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo BT Antenna Page 3 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo Page 4 of 4 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo

Page 1 of 8 Report No.: 26012122079RFC-2 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART1-V1.1 SAR TEST EXCLUSION EVALUATION REPORT Product Name: Portable Wireless Radio Trade Mark: Hearth & Hand with Magnolia Model No.: BTSP22 Report Number: 26012122079RFC-2 Test Standards: FCC 47 CFR Part 2.1093 FCC ID: 2AO23-BTSP22 Test Result: PASS Date of Issue: March 14, 2026 Prepared for: Chug, Inc. 7157 Shady Oak Rd, Eden Prairie MN 55344, United States Prepared by: Shenzhen UnionTrust Quality and Technology Co., Ltd. 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China TEL: +86-755-2823 0888 FAX: +86-755-2823 0886 Prepared by: Reviewed by: David Chen Henry Lu Senior Project Engineer Team Leader Approved by: Date: March 14, 2026 Billy Li Technical Director Page 2 of 8 Report No.: 26012122079RFC-2 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART1-V1.1 Version Version No. Date Description V1.0 March 14, 2026 Original Page 3 of 8 Report No.: 26012122079RFC-2 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART1-V1.1 CONTENTS 1. GENERAL INFORMATION ....................................................................................................................................... 4 1.1 CLIENT INFORMATION ........................................................................................................................................ 4 1.2 EUT INFORMATION ............................................................................................................................................ 4 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD ................................................................................. 4 1.4 OTHER INFORMATION ......................................................................................................................................... 5 1.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................................................... 5 1.6 DEVIATION FROM STANDARDS ............................................................................................................................ 5 1.7 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................. 5 1.8 OTHER INFORMATION REQUESTED BY THE CUSTOMER ........................................................................................ 5 2. EQUIPMENT LIST .................................................................................................................................................... 5 3. SAR TEST EXCLUSION EVALUATION ................................................................................................................... 6 3.1 REFERENCE DOCUMENTS FOR EVALUATION ........................................................................................................ 6 3.2 EXEMPTION LIMITS FOR ROUTINE EVALUATION – SAR EVALUATION ................................................................... 6 3.2.1 SAR TEST EXCLUSION THRESHOLD ....................................................................................................... 6 3.2.2 TEST PROCEDURE ................................................................................................................................. 7 3.3 MPE CALCULATION RESULTS ............................................................................................................................ 7 3.3.1 FOR BT ................................................................................................................................................. 7 APPENDIX 1 PHOTOS OF TEST SETUP ....................................................................................................................... 8 APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS ................................................................................... 8 Page 4 of 8 Report No.: 26012122079RFC-2 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART1-V1.1 1. GENERAL INFORMATION 1.1 CLIENT INFORMATION Applicant: Chug, Inc. Address of Applicant: 7157 Shady Oak Rd, Eden Prairie MN 55344, United States Manufacturer 1: Hunan XuanTong Technology Co., Ltd. Address of Manufacturer 1: B2 Building, Standard Factory, Caojiapeng Four Phases, Baofeng Street, Shimen County, Changde City, Hunan Province, China Manufacturer 2: Dongguan Roker Intelligent Technology Co., Ltd. Address of Manufacturer 2: Building 3, No. 35, Dongping Road Changping Section, Changping Town, Dongguan, Guangdong, China Manufacturer 3: Rocker Technology Co., Ltd. Address of Manufacturer 3: Building S3, 2nd Floor, Area A, Star Maiya Innovation Science and Technology Park, Prey Roka Village, Chok Chheu Neang Commune, Ang Snoul District, National Road 4, Kandal Province, Phnom Penh, Cambodia 1.2 EUT INFORMATION Product Name: Portable Wireless Radio Model No.: BTSP22 Trade Mark: Hearth & Hand with Magnolia DUT Stage: Identical Prototype EUT Supports Function:…

Text truncated - open the document above for the full version.

Antenna Specification Summary ITEM ANT SPEC Model Name 2.4G ANT Center Frequency Horizontal Vertical 2400MHz 2400MHz 2500MHz 2400MHz 2400MHz 2500MHz -1.26-0.76-0.58-5.25-2.46-1.86 MAX. Gain -0.58dBi Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Antenna Type PCB Antenna Antenna Length 38.20mm Manufacture SHENZHEN BLUETUM TECHNOLOGY CO.,LTD Adress 1301-1 Building A,Zhihui Square,No.4068 Qiaoxiang Road,GaofaCommunity,Shahe Street,Nanshan District,Shenzhen,P.R.China Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Frequency (MHz) Gain(dBi) Max Min Avg 2400 -1.26174 -30.0801 -7.18716 2450 -0.765802 -36.5604 -7.48023 2500 -0.585582 -22.0315 -6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Frequency (MHz) Gain(dBi) Max Min Avg 2400 -5.2537-22.1424-12.4294 2450 -2.4652-24.5837-10.4702 2500 -1.86120-29.5214-9.20432

Page 1 of 65 Report No.: 26012122079RFC-1 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART15.247-V1.1 FCC TEST REPORT Product Name: Portable Wireless Radio Trade Mark: Hearth & Hand with Magnolia Model No.: BTSP22 Report Number: 26012122079RFC-1 Test Standards: FCC 47 CFR Part 15 Subpart C FCC ID: 2AO23-BTSP22 Test Result: PASS Date of Issue: March 14, 2026 Prepared for: Chug, Inc. 7157 Shady Oak Rd, Eden Prairie MN 55344, United States Prepared by: Shenzhen UnionTrust Quality and Technology Co., Ltd. 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China TEL: +86-755-2823 0888 FAX: +86-755-2823 0886 Prepared by: Reviewed by: David Chen Henry Lu Senior Project Engineer Team Leader Approved by: Date: March 14, 2026 Billy Li Technical Director Page 2 of 65 Report No.: 26012122079RFC-1 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART15.247-V1.1 Version Version No. Date Description V1.0 March 14, 2026 Original Page 3 of 65 Report No.: 26012122079RFC-1 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-FCCPART15.247-V1.1 CONTENTS 1. GENERAL INFORMATION ....................................................................................................................................... 4 1.1 CLIENT INFORMATION ........................................................................................................................................ 4 1.2 EUT INFORMATION ............................................................................................................................................ 4 1.2.1 GENERAL DESCRIPTION OF EUT ............................................................................................................ 4 1.2.2 DESCRIPTION OF ACCESSORIES ............................................................................................................. 4 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD ................................................................................. 5 1.4 OTHER INFORMATION ......................................................................................................................................... 5 1.5 DESCRIPTION OF SUPPORT UNITS ...................................................................................................................... 6 1.6 TEST LOCATION ................................................................................................................................................. 6 1.7 TEST FACILITY................................................................................................................................................... 6 1.8 DEVIATION FROM STANDARDS ............................................................................................................................ 6 1.9 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................. 6 1.10 OTHER INFORMATION REQUESTED BY THE CUSTOMER ........................................................................................ 7 1.11 MEASUREMENT UNCERTAINTY ........................................................................................................................... 7 2. TEST SUMMARY ...................................................................................................................................................... 8 3. EQUIPMENT LIST .................................................................................................................................................... 9 4. TEST CONFIGURATION ........................................................................................................................................ 10 4.1 ENVIRONMENTAL CONDITIONS FOR TESTING ...................................................................................................... 10 4.1.1 NORMAL OR EXTREME TEST CONDITIONS ............................................................................................. 10 4.1.2 RECORD OF NORMAL ENVIRONMENT AND TEST SAMPLE ........................................................................ 10 4.2 TEST CHANNELS ............................................................................................................................................. 10 4.3 EUT TEST STATUS .......................................................................................................................................... 10 4.4 PRE-SCAN .................................................................................................................................................... 11 4.4.1 WORST-CASE DATA PACKETS ................................................................................................................ 11 4.4.2 TESTED CHANNEL DETAIL ..................................................................................................................... 11 4.5 TEST SETUP .................................................................................................................................................... 12 4.5.1 FOR RADIATED EMISSIONS TEST SETUP ................................................................................................ 12 4.5.2 FOR CONDU…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com APPENDIX 1 PHOTOS OF TEST SETUP Radiated emission Test Setup (30 MHz~1 GHz) Radiated emission Test Setup (Above 1 GHz) Page 2 of 2 FCC ID: 2AO23-BTSP22 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua Street, Longhua District, Shenzhen,Guangdong,China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com RF Conducted Test Setup Conducted Emission Test Setup