2AO23-BTSP68Sound Bar

included • Sound Bar • Remote Control • Power Adapter • AUX Cable • Optical Cable • AUX to RCA Cable indicators Rapid Flashing White - Pairing Solid Blue - Paired with playback Solid Yellow - AUX mode Solid Green - Optical mode Flashing Blue - Muted in bluetooth mode Flashing Yellow - Muted in AUX mode Flashing Green - Muted in optical mode Solid Red - Charging mode No Light - Power o/charging complete • Ascending Tones - Power on • Descending Tones - Power o • Two Rapid Dings - Low battery • Double Chime - Paired • Medium Pitched Double Chime - AUX connected • High Pitched Double Chime - Optical connected • Three Rapid Tones - Disconnected • Quick Ascending Tone - Max volume • Quick Descending Tone - Min. volume • Two Beeps - Incoming call using bluetooth • Press the power button to turn on the sound bar • When turning on the sound bar for the rst time it will automatically enter pairing mode • The indicator light will ash white when it is ready to pair • Use the bluetooth settings on your device to pair with HEYDAY SOUNDBAR 01 • The sound bar is connected the indicator light will start to ash blue, followed by a chime; the light will turn solid with playback • The sound bar will automatically reconnect to the device it was most recently paired to when you turn the sound bar on and it is in bluetooth mode • To re-enter paring mode disconnect from your device using the bluetooth menu • You can also re-enter pairing by holding the bluetooth button until you hear two rapid dings and the indicator light is ashing white; follow the above steps to connect your device again optical • Remove the protective tip on the connectors • Insert the optical cable into the back of the sound bar optical port • Insert the opposite end of the optical cable into the back of your device • Press the input button to switch to the optical function, and switch your device to optical note: If optical is selected on your device and no sound comes out you may need to activate PCM audio output on your device • When in optical mode and the sound bar is powered o, it will power back on in optical mode • Place the sound bar on a sturdy at surface • Plug the included power adapter into the power port and into a grounded wall outlet • If you need to use a dierent power source make sure it is a power supply of DC 15V 1.6A minimum warning: please use UL compliant power supply • Full charge requires approximately 3 hours and will provide 8 hours of use at 50% volume • When the charging indicator turns o, charging is completed note: The light will not indicate it is charging when the sound bar is in use charging • Insert 3.5mm AUX cable or AUX to RCA cable into the sound bar AUX port • Insert opposite end of the AUX cable into your device • Press the input button to switch to the AUX function, and switch your device to AUX AUX/line in/RCA • Press the play/pause button to answer/end incoming calls • Hold the play/pause button to reject incoming calls phone calls • The tablet holder ts most tablets, when using the holder be sure that the tablet is in landscape mode for the best stabilization using the tablet holder input • Press the input button to switch from bluetooth,AUX, and optical sound bar hey! welcome to your heyday™ sound bar. let’s get you set up. top microphone press - vol. up hold - next track press - vol. down hold - prev. track play/ pause input button bluetooth button power button tablet holder back power port AUX port optical port front indicator light NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Target Corp. Mpls. MN, 55403 Phone: 1-612-304-6073 FCC ID: 2AO23-BTSP68 Model: BTSP68 Input: 15V 1.6A Max AC/DC Adapter Input: 100-240V~50/60Hz 0.8A Output: 15.0V 1.6A Battery Capacity: 7.4V/ 2500mAh/ 18.5Wh Remote Connection Distance: 3 meters (9.84 feet) Made in China This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • Do not use near any water source • Do not modify or repair this device • Do not use in high temperatures or extreme weather • Do not use chemical detergents to clean your device, use a soft dry cloth • Do not drop the product and do not expose it to any major shocks. • Do not operate the product outside the power limits given in the specications. • Protect the product from dirt, moisture and overheating and use it in dry rooms only. • As with all electrical devices, this device should be kept out of the reach of children. safety Can’t get the sound bar to pair? Have a question or comment? call us at: 877-698-4883 or: 877-MyTgtTech online at: TargetTechSupport.com need some help? • If the sound bar…

Text truncated - open the document above for the full version.

C5266091_X8_Ed.1 1/1 Letter of Authorization Chug, Inc. Company: Chug, Inc. Address: 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Product Name: Sound Bar Model Number: BTSP68 FCC Identifier: 2AO23-BTSP68 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Michael Clemmer Date: 7/7/2021 Title: General manager Signature of applicant:

C5266091_X10_Ed.1 1/1 Chug, Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 7/7/2021 Subject: Request for Confidentiality FCC ID: 2AO23-BTSP68 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Michael Clemmer Date: 7/7/2021 Title: General manager

1 - Page 1 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] APPENDIX 1- EUT PHOTO Photo 1 (For model BTSP68) Photo 2 1 - Page 2 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 1 - Page 3 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 1 - Page 4 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 7 ----END OF REPORT----

1 - Page 1 of 5 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] APPENDIX 1- EUT PHOTO Photo 1 (For model BTSP68) Photo 2 1 - Page 2 of 5 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 BT ANT 1 - Page 3 of 5 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 1 - Page 4 of 5 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 7 Photo 8 1 - Page 5 of 5 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 9 Photo 10 ----END OF REPORT----

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] RF EXPOSURE Test Report Report No.: MTi210608017-02E2 Date of issue: July 05, 2021 Applicant: Chug, Inc. Product name: Sound Bar Model(s): BTSP68 FCC ID: 2AO23-BTSP68 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 6- Report No.: MTi210608017-02E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 6- Report No.: MTi210608017-02E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] TEST RESULT CERTIFICATION Applicant’s name .................... Chug, Inc. Address .................................. 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Manufacturer's Name ............. Shenzhen SeeMeHere Electronic Co., Ltd. Address .................................. 1st, 2nd, 3rd and 5th FL, Buiding B, TongFuYu Industrial, No.32 Hangkong Road, Sanwei Community, Hangcheng St. Bao'an, Shenzhen, Guangdong, China Product description Product name ........................... Sound Bar Trademark ............................. heyday Model Name .......................... BTSP68 Serial Model ........................... N/A Standards ............................... N/A Test procedure ....................... KDB 447498 D01 v06 Date of Test Date (s) of performance of tests ............ : June 23, 2021 ~July 05, 2021 Test Result ............................................. : Pass This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Testing Engineer : (Danny Xu) Technical Manager : (Leo Su) Authorized Signatory : (Tom Xue) - Page 4 of 6- Report No.: MTi210608017-02E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1. STANDALONE SAR TEST EXCLUSION CONSIDERATIONS ............................................................................................ 5 2. SAR TEST EXCLUCSION THRESHOLDS ........................................................................................................................ 6 - Page 5 of 6- Report No.: MTi210608017-02E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] 1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance defined in 4.1 f) is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified, typically in the SAR measurement or SAR analysis report, by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting are required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions. a) For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where  f (GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison  The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm, and for transmission f…

Text truncated - open the document above for the full version.

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi210608017-02E1 Date of issue: July 05, 2021 Applicant: Chug, Inc. Product name: Sound Bar Model(s): BTSP68 FCC ID: 2AO23-BTSP68 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 69 - Report No.: MTi210608017-02E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 69 - Report No.: MTi210608017-02E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1 GENERAL INFORMATION .......................................................................................................................................... 6 1.1 DESCRIPTION OF EUT ................................................................................................................................................... 6 1.2 OPERATION CHANNEL LIST .............................................................................................................................................. 6 1.3 TEST CHANNEL LIST ....................................................................................................................................................... 7 1.4 ANCILLARY EQUIPMENT LIST ........................................................................................................................................... 7 1.5 DESCRIPTION OF SUPPORT UNITS .................................................................................................................................... 7 2 SUMMARY OF TEST RES U LT S .................................................................................................................................... 8 3 TEST FACILITIES AND ACCREDITATIONS ..................................................................................................................... 9 3.1 TEST LABORATORY ........................................................................................................................................................ 9 3.2 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 9 3.3 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 9 3.4 TEST SOFTWARE ........................................................................................................................................................... 9 4 EQUIPMENT LIST .................................................................................................................................................... 10 5 TEST RESULT ........................................................................................................................................................... 11 5.1 ANTENNA REQUIREMENT ............................................................................................................................................. 11 5.1.1 Standard requirement ....................................................................................................................................... 11 5.1.2 EUT antenna ..................................................................................................................................................... 11 5.2 PEAK OUTPUT POWER ................................................................................................................................................. 12 5.2.1 Limit .................................................................................................................................................................. 12 5.2.2 Test setup .......................................................................................................................................................... 12 5.2.3 Test procedure ................................................................................................................................................... 12 5.2.4 Test results......................................................................................................................................................... 12 5.3 CONDUCTED EMISSION ................................................................................................................................................ 19 5.3.1 Limits ................................................................................................................................................................. 19 5.3.2 Test setup .......................................................................................................................................................... 19 5.3.3 Test procedure ................................................................................................................................................... 20 5.3.4 Test results.......................…

Text truncated - open the document above for the full version.

Model: BTSP68 Radiated emission Conducted emission