2AO23-CAB66Wireless charging Car Mount

charging car mount installation The car mount comes in two separate pieces and requires some assembly. dash armcar mount 1 2 To assemble insert the ball joint on the dash arm into the back of the car mount. Be sure not to press too hard so you do not damage either part of the mount. 3 Twist the nut on the on the dash arm to attach it to the car mount. Be sure to twist the nut all the way onto the mount or it will not stay up right when the phone is inserted. nut 4 screw lock Clean the dash board or window and place the assembled mount onto it. Press down the lock under the arm to lock the suction. Then adjust the dash arm and tighten the screw to lock it into the desired position. 6 FCC ID: 2AO23-CAB66 Model: CAB66 Input: 9V 2A 12V 1.5A Output: 10W Max Made in China This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Target Corp. Mpls. MN, 55403 Phone: 612-304-6073 • Remove credit cards and other cards with magnetic strips to prevent damage to the cards • Keep the charger away from heat and direct sunlight • Do not modify or repair this device • Do not use in high temperatures or extreme weather • Do not use chemical detergents to clean your device, use a soft dry cloth • Immediately unplug it from its power source if it gets wet safety • Double check that the USB-C charging cable and car charger are plugged in • Certain phone cases may interfere with wireless charging. Remove the phone case for best results • Double check the placement of the device on the wireless charger. For best results, the center of the device should be on the center of the wireless charger • Wireless charging is compatible with iPhone 8 and newer as well as other Qi-enabled devices. Please consult your devices user manual if you are unsure if your device is compatible troubleshooting Can’t get it to charge? Just have a question? call us at: 877-698-4883 or: 877-MyTgtTech e-mail us at: TargetTechSupport.com need some help? 8 in front back coverpage 4 page 2 page 3 how to fold DO NOT PRINT coverpage 4 5 To open the mount press the two buttons on the bottom of the car mount at the same time. The arms will automatically span out. buttonbutton Place your phone into the mount and press the arms in to secure it. If you need to adjust or remove your phone follow step 5. 7 Certain surfaces may cause issues with the suction lock. If you’re having issues use the mounting plate to create a smooth surface. To use it, clean the desired surface, remove the adhesive backing, press on the desired location, and wait 3-5 minutes before use. Follow step 4 to mount. 7 Driving while distracted is dangerous. Do not use your phone while your vehicle is in motion. Check your states laws on window and dash mounts to ensure you’re not breaking them. warning: • If the mount won’t stay upright be sure that the dash arm is fully screwed into the mount • If you can’t remove the dash arm, make sure the lock is ipped up and use the tabs on the suction cup to help break the seal • If the suction cup is having issues sticking, it may need to be cleaned. Rinse under cold water to wash away any debris and refresh the sticky gel. Wait for it to dry before use. installation tips bottomfront usb-c port charging indicator • Follow the assembly instructions and make sure the mount is secure and in the desired position • Plug the car charger into the aux outlet and connect to the car mount using the USB-C charging cable • If you need to use a dierent power source make sure it is a USB power supply of DC 9V 2A minimum warning: please use UL compliant power supply • Place your QI-enabled device onto the wireless charger and align the device with the center of the charging surface or the device will not charge • Remove credit cards or any card with a magnetic strip to prevent damage to the cards before charging • Charge time will vary by device charging • Alignment matters - centering the device on the charging surface ensures the fastest and most ecient charge • Thick phone cases as well as some materials can interfere with the ability to charge • This is a high speed wireless charger. Make the most of the charger by using the USB-C charging cable and car charger that were packaged with it. Using a dier…

Text truncated - open the document above for the full version.

Chug, Inc. Statement Product Name: Wireless charging Car Mount Model No.: CAB66, PW014 We( Chug, Inc. ; 7157 Shady Oak Road, Eden Prairie, MN 55344, USA ) hereby state that all models above are identical in interior structure, electrical circuits and components, and just the model names are different for marking requirement. Signature: Name / title:Michael Clemmer / General M anager Tel: ++8613798203746 Date: 2020/8/1

C5266091_X8_Ed.1 1/1 Letter of Authorization Chug, Inc. Company: Chug, Inc. Address: 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Product Name: Wireless charging Car Mount Model Number: CAB66, PW014 FCC Identifier: 2AO23-CAB66 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Michael Clemmer Date: 8/3/2020 Title: general manager S ignature of applicant:

C5266091_X10_Ed.1 1/1 Chug, Inc. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 8/3/2020 Subject: Request for Confidentiality FCC ID: 2AO23-CAB66 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Michael Clemmer Date: 8/3/2020 Title: general manager

- Page 1 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China APPENDIX 1: EUT PHOTO Photo 1 (For model CAB66) Photo 2 - Page 2 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 3 Photo 4 - Page 3 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 5 Photo 6 - Page 4 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 7 Photo 8 - Page 5 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 9 Photo 10 - Page 6 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 11 Photo 12 - Page 7 of 7 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 13 ----END OF REPORT----

PW01420200706-1 A 2020/6/5 丘伟金 2020/7/6 FST- PW014 -- - FSD-024 BACK SIDE OF MOUNT

- Page 1 of 5 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China APPENDIX 1: EUT PHOTO Photo 1 (For model CAB66) Photo 2 - Page 2 of 5 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 3 Photo 4 - Page 3 of 5 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 5 Photo 6 Coil antenna - Page 4 of 5 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 7 Photo 8 - Page 5 of 5 - Report No.: MTi20071508-1E1-1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Photo 9 ----END OF REPORT----

This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China EXPOSURE REPORT FCC ID:2AO23-CAB66 Date of issue: July 23, 2020 Report Number: MTi20071508-1E2 Sample Description: Wireless charging Car Mount Mo d e l( s ) : CAB66, PW014 Applicant: Chug, Inc. Address: 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Date of Test: July 15, 2020 – July 23, 2020 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 9 - Report No.: MTi20071508-1E2 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Test Result Certification Applicant’s name: Chug, Inc. Address: 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Manufacture's name: SHENZHEN RIHUIDA ELECTRONICS CO., LTD. Address: The 01st, 02nd, 03rd and 04th floors of the fourth building & the 02nd, 03rd and 04th floors of the third building of Fuzhong Industrial Park, Huaide Community, Fuyong Street, Bao’an District, Shenzhen City, Guangdong Province, China. Product name: Wireless charging Car Mount Trademark: heyday Model name: CAB66, PW014 Standard: FCC CFR 47 PART 1 , 1.1310 RF Exposure Procedures: KDB 680106 D01 RF Exposure Wireless Charging App v03 This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Tested by: Demi Mu July 23, 2020 Reviewed by: Leo Su July 23, 2020 Approved by: Tom Xue July 23, 2020 - Page 3 of 9 - Report No.: MTi20071508-1E2 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China 1 General Information 1.1 Description of EUT Product name: Wireless charging Car Mount Brand name: heyday Model name: CAB66 Series model: PW014 Deference in serial model: All the models are of the same circuit and RF module, except the model No.. Operation frequency: 115–205 kHz Operational mode: Wireless charging Modulation type: ASK Antenna type: Coil Antenna Power source: DC 12V from Car charger Battery: N/A Adapter information: N/A 1.2 Ancillary equipment list Equipment Model S/N Manufacturer / / / / / / / / 1.3 Measurement uncertainty Measurement Uncertainty for a Level of Confidence of 95 %, U=2xUc(y) Radiated emission(150kHz~30MHz) ± 2.5 dB Radiated emission(30MHz~1GHz) ± 4.2 dB Radiated emission (above 1GHz) ± 4.3 dB Temperature ±1 degree Humidity ± 5 % - Page 4 of 9 - Report No.: MTi20071508-1E2 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China 2 Testing site Test Site Shenzhen Microtest Co., Ltd Test Site Location No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China FCC Registration No.: 448573 - Page 5 of 9 - Report No.: MTi20071508-1E2 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China 3 List of test equipment Equipment No. Equipment Name Manufacturer Model Serial No. Calibration date Due date MTI-E068 Broadband Field Meter Narda Safety Test Solutions GmbH NBM- 520 D-1699 2020/07/13 2021/07/12 MTI-E069 Probe E-Field Narda Safety Test Solutions EF0691 H-0571 2020/07/13 2021/07/12 - Page 6 of 9 - Report No.: MTi20071508-1E2 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China 4 Test Results 4.2 Maximum permissible exposure 4.2.1 Limit Frequency range(MHz) Electric field strength(V/m) Magnetic field strength(A/m) Power density(mW/cm2) Averaging time(minutes) (A) Limits for Occupational/Controlled Exposure 0.3-3.0 614 1.63 *100 6 3.0-30 1842/f 4.89/f *900/f 2 6 30-300 61.4 0.163 1.0 6 6 300-1500 f/300 6 1500-100000 5 6 (B) Limits for General Population/Uncontrolled Exposure 0.3-1.34 614 1.63 *100 30 1.34-30 824/f 2.19/f *180/f 2 30 30-300 27.5 0.073 0.2 30 300-1500 f/1500 30 1500-100000 1 30 f = frequency in MHz * = Plane-wave equivalent power density 4.2.2 Test Procedures E and H-field measurements should be made with the center of the probe at a distance of 15 cm surrounding the device and 20 cm above the top surface of the primary/client pair. These measurements should be repeated for three different client battery levels, 1%, 50%, and 99%. Record the test results. KDB 680106 D01 RF Exposure Wireless Charging App v03: (1) Power transfer frequency is less than 1MHz. (2) Output power from each primary coil is less than or equal to 15 watts. (3) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils. (4) Client device is placed directly in contact with the transmitter. (5) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion). (6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the M…

Text truncated - open the document above for the full version.

This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Test Report FCC ID:2AO23-CAB66 Date of issue: July 31, 2020 Report number: MTi20071508-1E1 Sample description: Wireless charging Car Mount Mo d e l( s ) : CAB66, PW014 Applicant: Chug, Inc. Address: 7157 Shady Oak Road, Eden Prairie, MN 55344, USA Date of test: July 15, 2020 – July 23, 2020 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 19 - Report No.: MTi20071508-1E1 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China Table of Contents 1 GENERAL INFORMATION ................................................................................................................................... 4 1.1 FEATURE OF EQUIPMENT UNDER TEST (EUT) ................................................................................................................... 4 1.2 TEST MODE .............................................................................................................................................................. 4 1.3 EUT TEST SETUP........................................................................................................................................................ 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 SUMMARY OF TEST RESULT ............................................................................................................................... 6 2.1 OPERATION CHANNEL LIST ........................................................................................................................................... 6 2.2 TEST CHANNEL .......................................................................................................................................................... 6 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 7 3.1 TEST LABORATORY ..................................................................................................................................................... 7 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 7 3.3 MEASUREMENT UNCERTAINTY ...................................................................................................................................... 7 3.4 TEST SOFTWARE ........................................................................................................................................................ 7 4 LIST OF TEST EQUIPMENT .................................................................................................................................. 8 5 TEST RESULTS ..................................................................................................................................................... 9 5.1 ANTENNA REQUIREMENT ............................................................................................................................................ 9 5.1.1 Standard requirement ................................................................................................................................. 9 5.1.2 EUT Antenna ............................................................................................................................................... 9 5.2 CONDUCTED EMISSION ............................................................................................................................................. 10 5.2.1 Limits ......................................................................................................................................................... 10 5.2.2 Test Procedures ......................................................................................................................................... 10 5.2.3 Test Setup .................................................................................................................................................. 10 5.2.4 Test Result ................................................................................................................................................. 10 5.3 RADIATED EMISSION ................................................................................................................................................. 11 5.3.1 Limits ......................................................................................................................................................... 11 5.3.2 Test Procedures ......................................................................................................................................... 12 5.3.3 Test Setup .................................................................................................................................................. 13 5.3.4 Test Result ................................................................................................................................................. 13 5.4 OCCUPIED BANDWIDTH............................................................................................................................................. 17 5.4.1 Test method ............................................................................................................................................... 17 5.4.2 Test resu…

Text truncated - open the document above for the full version.

Model: CAB66 Radiated emission