2AO7C-81000001Energy Harvesting Sensor Node

2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com User’s Manual FCC warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada (IC) warning: Canada Low-power license-exempt radio communication devices (RSS-247) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF Exposure and Separation Distance: For safe operation, the minimum separation distance should be 20cm. Pour un fonctionnement en toute sécurité, la distance de séparation minimale doit être de 20 cm. 2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com Note: The Silver Glade hardware is part of a service package sold by Everactive and is not for sale as an individual standalone product and as such is not open for end customers to program or configure. The following User’s Guide is an instruction set used to program and control Boomerang to prepare it for integration with Everactive’s service, or test and debug. Hardware setup for test mode Hardware needs: 1. SVG Prog 2.0 Programming board 2. Silver Glade Hardware 3. Everactive USB-C attachment cable Note: for programming and SW control, harvesting mode is bypassed, eliminating the need for the energy harvesting puck. Later sections will describe the install of a Silver Glade unit onto a motor. Connect SVG Prog. 2.0 into a USB 3.0 input on a computer or USB Hub. Then connect the Everactive USB C attachment cable from the IO ‘MAIN USB-C’ to the USB C input on Silver Glade (see Figure below). Figure 1: Silver Glade connected to programming device 2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com Software control for running tests and performing debug Unzip the following package to your computer: svg_fcc_scripts_b7cb02ed.zip Go to the unzipped folder and run program Silver Glade using the fcc.py python script. python fcc.py –-h % view all available configuration options Figure 2: Options for programming Silver Glade for wireless communication For conducted wireless tests the top cap of Silver Glade can be unscrewed and the cap plus antenna removed. This will allow a conducted connection to a spectrum analyzer or network analyzer (see Figure X). Otherwise, leaving the cap and antenna connected will leave Silver Glade ready for over the air testing (see Figure X). Figure 3: Silver Glade with cap and antenna removed for conducted wireless testing 2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com In order to run SW tests on a PC confirm which COM port the Silver Glade HW is assigned to. Go to the device manager. One ‘USB Serial Port’ is for SVG Prog 2.0 and one is for Silver Glade. Figure 4: Identify the USB Serial Port In our examples, the COM port for Silver Glade is COM15. Knowing that a user can configure Silver Glade to perform wireless tests using the options above. Examples: Measure transmitted output power on various channels: python fcc.py –-serport COM15 –-cw –-channels “0, 16, 32, 48, 63” –-power 10 Run in frequency hopping mode: python fcc.py –-serport COM15 –-freq_hop –-power 10 Installation on a motor Installation on a motor is designed to be fast and easy. On any motor that has sufficient heat differential between the motor body to ambient room, meeting product specifications, a Silver Glade unit can be adhered to the motor, either through its magnetic base or attached with an epoxy or glue. Attaching the energy harvesting puck to Silver Glade using the USB-C port and required cable will be sufficient to power the Silver Glade unit. The Silver Glade unit can then be paired via the Evergateway. Figure 5: Silver Glade unit paired with both PV and TEG energy harvesting modules

2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com March 10, 2020 Federal Communications Commission Equipment Authorization branch 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resoluti on of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contai ns any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specifie d standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; 2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance wi th requirements of the relevant standard and to make these records available to the when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, David D. Wentzloff Everactive

2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: 2AO7C-81000001 To Whom It May Concern: Pursuant to th e provisions of Sections 0.457 and 0.459 of th e Commission’s rule s (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Antenna Specification Above mentioned document contains detailed system and equipment description ar e considered as proprietary information in operation of t he e quipment. The public disclosure of a bove documents might be h armful to our company and woul d give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in o rder to c omply with t he marketing regulations in 47 C FR § 2.803 and t he importation rules in 47 C FR § 2.1204, while ensuring t hat business sensitive information remains confidential until the actual marketing of n ewly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until Aug. 31, 20 20 External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com Best Regards David D. Wentzloff Co- CTO March 10, 2020

2348 Walsh Avenue Santa Clara, CA 95051 [email protected] www.everactive.com Proposed ID Label and Location Proposed ID Label: Proposed Location Hardware

NVLAP Lab code: 200065-0 TEST REPORT Report Number. : 13257051-E3V3 Applicant : EVERACTIVE 2986 OAKMEAD VILLAGE CT SANTA CLARA, CA 95051 U.S.A. Model : 810-00001 FCC ID : 2AO7C-81000001 ISED ID : 23743-81000001 EUT Description : Energy harvesting sensor node Test Standard(s) : FCC Part 1 Subpart I FCC Part 2 Subpart J INDUSTRY CANADA RSS 102 ISSUE 5 Date Of Issue: May 27, 2020 Prepared by: UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538 U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 13257051-E3V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 2 of 11 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By V1 5/06/2020 Initial Issue - V2 5/22/2020 Report revised based on reviewer’s comments. Bobby Bayani V3 5/27/2020 Report revised based on reviewer’s comments. Sec. 2 updated. Bobby Bayani REPORT NO: 13257051-E3V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 3 of 11 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. REFERENCES ................................................................................................................... 5 4. FACILITIES AND ACCREDITATION ................................................................................. 5 5. MAXIMUM PERMISSIBLE RF EXPOSURE ....................................................................... 6 5.1. FCC RULES ................................................................................................................ 6 5.2. IC RULES .................................................................................................................... 7 5.3. EQUATIONS ................................................................................................................ 8 5.4. LIMITS AND IC EXEMPTION .....................................................................................10 6. RF EXPOSURE RESULTS ................................................................................................11 REPORT NO: 13257051-E3V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 4 of 11 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: EVERACTIVE 2986 OAKMEAD VILLAGE CT SANTA CLARA, CA 95051 U.S.A. EUT DESCRIPTION: Energy harvesting sensor node MODEL: 810-00001 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Pass INDUSTRY CANADA RSS 102 ISSUE 5 Pass UL Verification Services Inc. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of the U.S. government. Approved & Released For UL Verification Services Inc By: Prepared By: Thu Chan Bobby Bayani Operations Leader Lead Project Engineer UL Verification Service Inc. UL Verification Services Inc. REPORT NO: 13257051-E3V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 5 of 11 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 2. TEST METHODOLOGY All calculations were made in accordance with the following: • KDB 447498 D01 • KDB 447498 D03 3. REFERENCES All measurements were made as documented in test report no. 13257051-E1V3. Duty cycle, Antenna gain, and output power data is excerpted from the applicable test reports. 4. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0. REPORT NO: 13257051-E3V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 6 of 11 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 5. MAXIMUM PERMISSIBLE RF EXPOSURE 5.1. FCC RULES §1.1…

Text truncated - open the document above for the full version.

NVLAP LAB CODE 200065-0 TEST REPORT Report Number. : 13257051-E1V3 Applicant : EVERACTIVE 2986 OAKMEAD VILLAGE CT SANTA CLARA, CA 95051 U.S.A. Model : 810-00001 FCC ID : 2AO7C-81000001 ISED ID : 23743-81000001 EUT Description : Energy harvesting sensor node Test Standard(s) : FCC 47 CFR ISED RSS-247 ISED RSS-GEN Date Of Issue: May 27, 2020 Prepared by: UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 2 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By V1 05/06/2020 Initial Issue ---- V2 05/21/2020 Revised based on reviewer’s comments. Bobby Bayani V3 05/27/2020 Report revised based on reviewer’s comments. Sec. 8.2 updated. Bobby Bayani REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 3 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST METHODOLOGY ..................................................................................................... 7 3. FACILITIES AND ACCREDITATION ................................................................................. 7 4. DECISION RULES AND MEASUREMENT UNCERTAINTY .............................................. 8 4.1. METROLOGICAL TRACEABILITY .............................................................................. 8 4.2. DECISION RULES ....................................................................................................... 8 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 8 4.4. SAMPLE CALCULATION ............................................................................................ 8 5. EQUIPMENT UNDER TEST ............................................................................................... 9 5.1. EUT DESCRIPTION .................................................................................................... 9 5.2. MAXIMUM OUTPUT POWER...................................................................................... 9 5.3. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 9 5.4. SOFTWARE AND FIRMWARE .................................................................................... 9 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 9 5.6. DESCRIPTION OF TEST SETUP ...............................................................................10 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................13 7. MEASUREMENT METHODS ............................................................................................14 8. ANTENNA PORT TEST RESULTS ...................................................................................15 8.1. ON TIME AND DUTY CYCLE .....................................................................................15 8.2. 20 dB AND 99% BANDWIDTH ...................................................................................16 8.2.1. 99% OCCUPIED BANDWIDTH ...........................................................................17 8.2.2. 20dB BANDWIDTH ..............................................................................................18 8.3. HOPPING FREQUENCY SEPARATION ....................................................................19 8.4. NUMBER OF HOPPING CHANNELS .........................................................................20 8.5. AVERAGE TIME OF OCCUPANCY............................................................................21 8.6. OUTPUT POWER.......................................................................................................22 8.7. CONDUCTED SPURIOUS EMISSIONS .....................................................................23 9. RADIATED TEST RESULTS .............................................................................................26 9.1. TRANSMITTER ABOVE 1 GHz ..................................................................................27 9.2. TRANSMITTER BELOW 1 GHz ..................................................................................33 9.3. WORST CASE BELOW 30 MHz .................................................................................43 SPURIOUS EMISSIONS 9 kHz TO 30 MHz (WORST-CASE CONFIGURATION) .............43 REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 4 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 10. SETUP PHOTOS ...........................................................................................................44 REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 5 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: EVERACTIVE 2986 OAKMEAD VILLAGE CT SANTA CLARA, CA 95051 U.S.A. EUT DESCRIPTION: Energy harvesting sensor node MODEL: 810-00001 SERIAL NUMBER: 13118 (Radiated Sample) 13115 (Cond…

Text truncated - open the document above for the full version.

REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 44 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 10. SETUP PHOTOS ANTENNA PORT SETUP REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 45 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. RADIATED RF MEASUREMENT SETUP BELOW 1GHz (FRONT) BELOW 1GHz (BACK) ABOVE 1GHz (FRONT) ABOVE 1GHz (BACK) BELOW 30MHz (FRONT) ABOVE 30MHz (BACK) REPORT NO: 13257051-E1V3 DATE: 5/27/2020 FCC ID: 2AO7C-81000001 ISED ID: 23743-81000001 Page 46 of 46 UL VERIFICATION SERVICES INC. 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. ORIENTATIONS X-ORIENTATION Y-ORIENTATION Z-ORIENTATION END OF REPORT