2AOFP-300110Smart Connect Mini

2019.10.25 TP, rev13 Side 1 af 4 Smart Connect Mini user manual Compliance statement Smart Connect Mini and Smart Eye Mini Smart Connect Mini Contains FCC ID XMR201707BG96 Contains FCC ID 2AOFP-E0048 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Smart Eye Mini Contains FCC ID 2AOFP-E0048 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module, Contains FCC ID: 2AOFP-E0048. Information to user if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module, Contains FCC ID: 2AOFP-E0048. Caution: any changes or modifications not expressly approved by Anticimex Innovation Center A/S will void the user’s authority to operate the equipment. This equipment has been tested using a shielded network cable (STP). The Smart Connect Mini and Smart Eye Mini are only in compliance if no changes or modifications is made to the device The Smart Connect Mini and Smart Eye Mini are in compliance with the requirement for RF exposure in US with 20 cm separation distance between the user and/or bystander of the device. The latest version of the manuals and datasheets are always available on anticimexonline.sharepoint.com The antenna is fixed to the device and no change in antenna or fixation of the antenna is acceptable and such modification is considered to violate the Compliance Statement 2019.10.25 TP, rev13 Side 2 af 4 This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This device should be installed and operated with minimum distance of 20 cm from the human body. Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de brouillage, et 2. L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d’en compromettre le fonctionnement. The Smart Connect Mini uses the following frequency bands; FREQUENCY BAND MAX POWER LTE-FDD B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28 23dBm GSM850/EGSM900 33dBm DCS1800/PCS1900 30dBm GSM850/EGSM900 (8-PSK) 27dBm DCS1800/PCS1900 (8-PSK) 26dBm The Smart Connect Mini and Smart Eye mini also communicates using the following free SRD frequency bands; EU: 868 – 868.6 MHz with a maximum transmitting power of 14 dBm. Rest of the world: 917 – 926 MHz with a maximum transmitting power of 14 dBm. If an ethernet cable is used the product shall be connected using a shielded network cable (STP) that is properly grounded. Simplified declaration of conformity Hereby, Anticimex Innovation Center A/S declares that the radio equipment type Smart Connect Mini and Smart Eye Mini is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: anticimex.com/declaration-of-conformity Note: 2019.10.25 TP, rev13 Side 3 af 4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Instructions Only Anticimex service technicians are allowed to install, replace damaged units, and service installations. Replace the Smart Connect Mini or Smart Eye Mini if the device is faulty. To install the Smart Connect Mini system the operator must possess a mobile device such as a smartphone or tablet with access to an internet connection. To install, the operator should have a user in the Anticimex-owned software system “Smart Device Tool”. 1. Use Smart Device Tool to initiate an installation 2. Scan the QR-code of the Smart Connect Mini 3. Apply power to the Smart Connect Mini and await green flashes of the gateway, indicating beacon mode is active: You can now start to set up the sensors a. Start setting up sensors closest to the gateway 4. Push the button of the sensor and await green flashes, indicating connection 5. Continue to set up all the sensors of the installation in the same way 6. When all sensors have been installed, end the installation through Smart Device Tool a. During t…

Text truncated - open the document above for the full version.

External photos FCC ID: 2AOFP-300110 Front side Back side Top Bottom Left side Right side

C L Label to be placed here Text - min. point size 6 Label size: 51x25mm WEEE = min. height of 7mm QR code = Mac address + item no. 300110 + Reference no. CE =min. height of 5mm Production site TÜV logo - min. height of 9mm IP Rating Rev.DescriptionDateSign BContains FCC ID removed2019-08-23KRL C Revision add. ; QR code changed size ; Made in Thailand changed to production site. 2019-11-04KRL D Size changed to 51x25 ; address add. ; IP21 add. TÜV logo added 2019-12-09KRL 2019-12-09TP 1-0180 Non specified messurement according to 3D-file with same number and revision Tol. Non specified tolerances according to DS / ISO 2768-1 DateSign. Check Confidential. This drawing and its related technical information shall not be disclosed to third party without authorization. mm Units mm² Surface: Volume: Weight: g mm³ RSB2019-12-09 Approval Paper Size A41:2 Projection: First angle - Drawing-no.: File name: 1-0180 Label drawing for smart connect mini 300110 Revision General edge: DS/ISO 13715 Design Anticimex Innovation Center Skovgaardsvej 25 DK-3200 Helsinge Phone: +45 48 79 93 78 www.anticimex.com Scale Sheet Part-no.: Material: Description: General surface finish: DS / ISO 1302 KRL2019-06-13 1 / 1 D Label for Smart Connect Mini 300110 Top-coated thermal transfer printable polyester film Value white

Internal photos FCC ID: 2AOFP-300110 With antenna outside Copa-Cell board – Front side Copa-Cell board – Back side Copa-Mesh board – Front side Copa-Mesh board – Back side

Internal photos FCC ID: 2AOFP-E0048 With shieldcan Without shieldcan

Internal photo Model name：BG96, BG96 MINIPCIE sheilding No sheilding Front Side Back Side

Produkte Products Prüfbericht-Nr.: 60263491-003 Test Report No.: Seite 2 von 7 Page 2 of 7 Revisions Revisions Revision Revision Datum Date Anmerkung Remark Verfasser Author 001 2019-07-23 First Release Niall Forrester 002 2019-12-19 Updated power levels and calculations Niall Forrester 003 2020-01-21 Removed support for LTE NB-IoT Håkan Sjöberg Note: Latest revision report will replace all previous reports TABLE OF CONTENTS Table of Contents ................................................................................................................... 2 Product Information ................................................................................................................ 3 1.1 Equipment under Test (EUT) description ............................................................................................... 3 1.2 Wireless Technologies and Frequency Bands supported by the DUT .................................................. 3 1.3 Conducted Power and Antenna Gain ..................................................................................................... 4 Evaluation .............................................................................................................................. 4 1.4 Summary ................................................................................................................................................ 4 1.5 Limits ...................................................................................................................................................... 5 1.6 Stand-alone Calculations ....................................................................................................................... 6 1.7 Simultaneous Transmission Calculations .............................................................................................. 7 Produkte Products Prüfbericht-Nr.: 60263491-003 Test Report No.: Seite 3 von 7 Page 3 of 7 PRODUCT INFORMATION 1.1 Equipment under Test (EUT) description Model name: Smart Connect Mini Manufacturer: Anticimex Innovation Center A/S Model number: 300110 FCC ID: 2AOFP-300110 Description: Cellular and sub-GHz gateway for the smart Connect system 1.2 Wireless Technologies and Frequency Bands supported by the DUT Technology Band Frequency Range (Tx) Evaluation Performed GSM (GPRS) 850 824.2 MHz – 848.8 MHz YES GSM (GPRS) 900 880.2 MHz – 914.8 MHz NO GSM (GPRS) 1800 1710.2 MHz – 1784.8 MHz NO GSM (GPRS) 1900 1850.2 MHz – 1909.8 MHz YES LTE CAT-M1 B1 1920 MHz – 1980 MHz NO LTE CAT-M1 B2 1850 MHz – 1910 MHz YES LTE CAT-M1 B3 1710 MHz – 1785 MHz NO LTE CAT-M1 B4 1710 MHz – 1755 MHz YES LTE CAT-M1 B5 824 MHz – 849 MHz YES LTE CAT-M1 B8 880 MHz – 915 MHz NO LTE CAT-M1 B12 699 MHz – 716 MHz YES LTE CAT-M1 B13 777 MHz – 787 MHz YES LTE CAT-M1 B20 832 MHz – 862 MHz NO LTE CAT-M1 B28 703 MHz – 748 MHz NO ‘Sub GHz’ Proprietary 868.3 MHz 868.3 MHz NO ‘Sub GHz’ Proprietary 917-926 MHz 917 MHz – 926 MHz YES Produkte Products Prüfbericht-Nr.: 60263491-003 Test Report No.: Seite 4 von 7 Page 4 of 7 1.3 Conducted Power and Antenna Gain Technology Band Maximum Conducted Output Power (dBm) Antenna Gain (dBi) GSM (GPRS) 850 32.5 -1.9 GSM (GPRS) 1900 29.5 1.3 LTE CAT-M1 B2 25.7 1.0 LTE CAT-M1 B4 25.7 0.9 LTE CAT-M1 B5 25.7 -1.9 LTE CAT-M1 B12 25.7 1.4 LTE CAT-M1 B13 25.7 -1.6 ‘Sub GHz’ Proprietary 917-926 MHz 14.0 1.3 Maximum Power and Antenna Gain are based on details supplied by the device manufacturer. EVALUATION 1.4 Summary At 20cm, the device is compliant with the “General Population / Uncontrolled” requirements set out in FCC 47 CFR §1.1310 Table 1 (B) for all supported combinations of wireless technologies. Produkte Products Prüfbericht-Nr.: 60263491-003 Test Report No.: Seite 5 von 7 Page 5 of 7 1.5 Limits 47 CFR § 1.1310 - Radiofrequency radiation exposure limits Table 1B Limits for Maximum Permissible Exposure (MPE) (Limits for general Population / Uncontrolled Exposure) Frequency Range (MHz) Electric Field strength (V/m) Magnetic Field strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3 - 1.34 614 1.63 *100 30 1.34 - 30 824/f 2-19/f *180/f 2 30 30 - 300 27.5 0.073 0.2 30 300 - 1500 - - f/1500 30 1500 - 10000 - - 1.0 30 Notes: 1. ƒ = frequency in MHz 2. * = Plane-wave equivalent power density Produkte Products Prüfbericht-Nr.: 60263491-003 Test Report No.: Seite 6 von 7 Page 6 of 7 1.6 Stand-alone Calculations The Power Density at 20cm separation distance has been calculated for each of the transmitter technologies supported by the device according to a re-arrangement of the Friis formula, as below: 푆= 푃∗퐺 4휋∗푟² Where:  “S” is power density in mW/cm²  “P” is maximum avg. conducted power (incl. tolerances) in mW according to data from the manufacturer  “G” is the peak antenna gain (numerical) according to data from the manufacturer  “r” is the separation distance (20 cm) Power Density (S) at 20cm Distance for Each Transmitter Technology Band Frequency (MHz)* Power (dBm) P (mW) Gain (dBi) G (Numerical) r (cm) S (mW/cm 2 ) Limit** (mW/cm 2 ) GSM (GPRS) 850 824.2 32.5 1778.28 -1.9 0.65 20 0.23 0.55 GSM (GPRS) 1900 1850.2 29.5 891.25 1.3 1.35 20 0.24 1.00 LTE CAT-M1 B2 1850 25.7 371.54 1.0 1.26 20 0.09 1.00 LTE CAT-M1 B4 1710 25.7 371.54 0.9 1.23 20 0.09 1.00 LTE CAT-M1 B5 824 25.7 371.54 -1.9 0.65 20 0.05 0.55 LTE CAT-M1 B12 699 25.7 371.54 1.4 1.38 20 0.10 0.47 LTE CAT-M1 B13 777 25.7 371.54 -1.6 0.69 20 0.05 0.52 ‘Sub GHz’ Proprietary 917-926 MHz 917 14.0 25.12 1.3 1.35 20 0.01 0.61 *The lowest frequency in each band has been chosen, to give the most conservative limit **The limits listed are from FCC 47 CFR §1.1310 Table 1 (B): “Limits for General Population/Uncontrolled” From 300MHz to 1500MHz, the limit is f/1500 mW/cm 2 where “f” is the frequency in MHz From 1500MHz to 100000MHz, the limit is 1.0 mW/cm 2 Produkte Products Prüfbericht-Nr.: 60263491-003 Test Report No.: Seite 7 von 7 Page 7 of 7 1.7 Simultaneous Transmission Calculations The device can transmit on…

Text truncated - open the document above for the full version.

LAB N° 1356 TRF FCC_15.247_000 07/10/2016 Page 1 of 33 Test Report 47 CFR FCC Part 15 subpart C Intentional Radiators Report reference no. ...................... : 28118556-003 FCC Designation Number ............. : IT0008 FCC Test Firm Registration # ....... : 804595 Tested by (name + signature)..........: Andrea Bortolotti \ Tester Approved by (name + signature)......: Giovanni Molteni \ TM Date of issue .................................... : October, 2019-31 Total number of pages ..................... : 33 Pages Testing Laboratory ........................ : TÜV Rheinland Italia S.r.l. Address ............................................ : Via Mattei 3 - 20010 - Pogliano Milanese (MI) – Italy Applicant’s name ........................... : Anticimex Innovation Center A/S Address ............................................ : Skovgaardsvej 25 Test item description ..................... : COPA Mesh Trade Mark ....................................... : Manufacturer .................................... : Anticimex Innovation Center A/S Model/Type reference ...................... : COPA Mesh FCC ID ............................................. : 2AOFP- E0048 Ratings ............................................. : 3,6Vdc (internal battery) Sample ............................................ : Samples received on ....................... : 05/06/2019 TUV reference samples ................... : 190212 (sampled by the customer) Samples tested n. ............................ : 1 Testing ............................................ : Start Date: ....................................... : 06/06/2019 End Date: ........................................ : 07/06/2019 The results in this Test Report are exclusively referred to the tested samples. Without the written authorization of TÜV Rheinland Italia S.r.l., this document can be reproduced only integrally LAB N° 1356 Report No. 28118556-003 TRF FCC_15.247_000 07/10/2016 Page 2 of 33 SUMMARY 1. Release Control Record 3 2. Reference Standards 3 3. Summary of testing 4 4. General product information 5 5. General Chipset information 6 6. General Antenna information 7 7. Equipment Used During Test 8 8. Input/Output Ports 8 9. Power Interface 8 10. Derived model(s) 9 11. EUT Operation Modes 9 12. EUT Configuration Modes 10 13. Test Conditions and Results 11 12. MEASUREMENT UNCERTAINTY 33 LAB N° 1356 Report No. 28118556-003 TRF FCC_15.247_000 07/10/2016 Page 3 of 33 1. Release Control Record Test report Number Reason of change Date of Issue 28118556-001 Original release 05/09/2019 28118556-002 Re-tested: 15.247 (a) (2): 6dB Minimum Bandwidth for systems using digitally modulation 15:247 (d): 100 kHz Bandwidth of Frequency Band Edges 15:247 (e): Power Spectral Density Update test report with measure acquisition 23/09/2019 28118556-003 Re-tested: §15.247 (d): Out-of-band emissions §15.247 (d): 100 kHz Bandwidth of Frequency Band Edges Update test report with measure acquisition 31/10/2019 2. Reference Standards Standard Description FCC Part 15 (Subpart C) §15.247 Operation within the bands 902-928 MHz, 2400-2483,5 MHz, and 5725-5850 MHz. FCC Part 15 (Subpart C) §15.207 Conducted Limits FCC Part 15 (Subpart C) §15.209 Radiated emission limits; general requirements FCC Part 15 (Subpart C) §15.203 Antenna Requirement ANSI C63.4:2014 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz ANSI C63.10:2013 American National Standard for Testing Unlicensed Wireless Devices 558074 D01 DTS Meas Guidance v05 - August 24, 2018 Guidance for performing compliance measurements on digital transmission systems (DTS) operating under §15.247 LAB N° 1356 Report No. 28118556-003 TRF FCC_15.247_000 07/10/2016 Page 4 of 33 3. Summary of testing § 15.203 § 15.247 (b)(4)(i) Antenna Requirements PASS § 15.207 (a) Power Line Conducted Emission Not performed § 15.209 (a) (f) Radiated Emission Not performed § 15.215 (a) (b) (c) Additional provisions to the general radiated emission limitations PASS § 15.247 (a) Frequency Hopping Spread Spectrum Specifications: § 15.247 (a) (1) 20 dB Bandwidth N.A. 1 § 15.247 (a) (1) (i) Number of Hopping Channels Used, Carrier frequency Separation and Time occupancy in band 902÷908MHz N.A. 1 § 15.247 (a) (1) (ii) Number of Hopping Channels Used, Carrier frequency Separation and Time occupancy in band 5725÷ 5850 MHz N.A. 1 § 15.247 (a) (1) (iii) Number of Hopping Channels Used, Carrier frequency Separation and Time occupancy in band 2400÷2483,5 MHz N.A. 1 § 15.247 (a) (2) 6dB Minimum Bandwidth for systems using digitally modulation PASS § 15.247 (b) Maximum Peak Output Power: § 15.247 (b) (1) Peak Output Power (conducted) in band 2400÷2483,5 MHz and 5725÷ 5850 MHz (Hopping systems) N.A. 1 § 15.247 (b) (2) Peak Output Power (conducted) in band 902÷908MHz (Hopping systems) N.A. 1 § 15.247 (b) (3) RF power output (conducted) for systems using digitally modulation PASS § 15.247 (b) (4) Antenna gain PASS § 15.247 (c) Operation with directional antenna gains greater than 6 dBi N.A 3 § 15.247 (d) Out-of-band emissions PASS § 15.247 (d) 100 kHz Bandwidth of Frequency Band Edges PASS § 15.247 (e) Power Spectral Density PASS § 15.247 (f) Hybrid systems N.A. 2 § 15.247 (g) FHSS Transmission characteristics N.A. 1 § 15.247 (h) Recognition of occupied channel and multiple transmission system N.A. 1 Note 1 Not applicable for DTS equipment Note 2 No hybrid system Note 3 Antenna gain: 1,3dBi LAB N° 1356 Report No. 28118556-003 TRF FCC_15.247_000 07/10/2016 Page 5 of 33 Possible test case verdicts: - test case does not apply to the test object .... : N/A - test object does meet the requirement .......... : PASS - test object does not meet the requirement ... : FAIL General remarks: The test results presented in this report relate only to the object tested. The results contained in this report reflect the results for this particular model and serial number. It is the responsibility of the manufactur…

Text truncated - open the document above for the full version.

Produkte Products Prüfbericht-Nr.: 60301233-003 Test Report No.: Seite 2 von 34 Page 2 of 34 Revisions Revisions Revision Revision Datum Date Anmerkung Remark Verfasser Author 001 2019-10-17 First release Fariborz Abasi 002 2019-11-04 Peak emissions added to results above 1GHz Fariborz Abasi 003 2019-11-06 - Pages 18,23 and 23: added legends in the graphs - Pages 23 and 28: Corrected column titles in the result tables - Pages 29-32: Corrected the second column’s title (from average to QuasiPeak) Fariborz Abasi Note: Latest revision report will replace all previous reports Produkte Products Prüfbericht-Nr.: 60301233-003 Test Report No.: Seite 3 von 34 Page 3 of 34 Summary of Test Results FCC Rule Part Test item Result Remarks 15.107 15.207 Power Line Conducted Emission N/A Battery powered § 15.209 (a) (f) Radiated Emission PASS § 15.215 (a) (b) (c) Additional provisions to the general radiated emission limitations Not performed § 15.247 (a) Frequency Hopping Spread Spectrum Specifications: § 15.247(a) 20 dB Bandwidth N/A Not applicable for DTS equipment § 15.247 (a) (1) (i) Number of Hopping Channels Used, Carrier frequency Separation and Time occupancy in band 902÷908MHz N/A Not applicable for DTS equipment § 15.247 (a) (1) (ii) Number of Hopping Channels Used, Carrier frequency Separation and Time occupancy in band 5725÷ 5850 MHz N/A Not applicable for DTS equipment § 15.247 (a) (1) (iii) Number of Hopping Channels Used, Carrier frequency Separation and Time occupancy in band 2400÷2483,5 MHz N/A Not applicable for DTS equipment § 15.247 (a) (2) 6dB Minimum Bandwidth for systems using digitally modulation Not performed § 15.247 (b) Maximum Peak Output Power: § 15.247 (b) (1) Peak Output Power (conducted) in band 2400÷2483,5 MHz and 5725÷ 5850 MHz (Hopping systems) N/A Not applicable for DTS equipment § 15.247 (b) (2) Peak Output Power (conducted) in band 902÷908MHz (Hopping systems) N/A Not applicable for DTS equipment § 15.247 (b) (3) RF power output (conducted) for systems using digitally modulation Not performed § 15.247 (b) (4) Antenna gain Not performed § 15.247 (c) Operation with directional antenna gains greater than 6 dBi N/A § 15.247 (d) Out-of-band emissions Not performed § 15.247 (d) 100 kHz Bandwidth of Frequency Band Edges Not performed § 15.247 (e) Power Spectral Density Not performed § 15.247 (f) Hybrid systems N/A No hybrid system § 15.247 (g) FHSS Transmission characteristics N/A Not applicable for DTS equipment § 15.247 (h) Recognition of occupied channel and multiple transmission system N/A Not applicable for DTS equipment Possible test case verdicts: - test case does not apply to the test object ....: N/A - test object does meet the requirement ..........: PASS - test object does not meet the requirement ....: FAIL - test case not performed on the test object ....: n.p. Produkte Products Prüfbericht-Nr.: 60301233-003 Test Report No.: Seite 4 von 34 Page 4 of 34 Table of contents 1 Test Sites ............................................................................................................................... 5 2 Product Information ................................................................................................................ 6 2.1 General description ........................................................................................................................................ 6 2.2 Radio specific details ...................................................................................................................................... 6 2.2.1 Sub-GHz radio ........................................................................................................................................ 6 2.3 Equipment Under Test (EUT) identification .................................................................................................... 7 2.4 Ancillary equipment identification ................................................................................................................... 7 3 Test Methods and Operation modes ...................................................................................... 8 3.1 Test Methods .................................................................................................................................................. 8 3.2 Operation modes ............................................................................................................................................ 8 3.3 Tested channels/Frequencies ........................................................................................................................ 8 4 Test Methodology .................................................................................................................. 9 4.1 Radiated Emission Test ................................................................................................................................. 9 5 Test Results – Radiated Emissions ..................................................................................... 12 5.1 Summary - Radiated emissions ................................................................................................................... 12 5.2 Test setups ................................................................................................................................................... 13 5.3 Detailed Test results - Radiated Emission ................................................................................................... 14 5.3.1 917 MHz proprietary radio frequency.................................................................................................... 14 5.3.2 922 MHz proprietary radio frequency.................................................................................................... 19 5.3.3 926 MHz proprietary radio frequency.................................................................................................... 24 5.4 Test results, Band edge restricted band m…

Text truncated - open the document above for the full version.

Produkte Products Prüfbericht-Nr.: 60338060-001 Appendix 1 Test Report No.: Seite 1 von 4 Page 1 of 4 1 APPENDIX 1 – TEST SETUP PHOTOS 1.1 Radiated Emissions Photos 1.1.1 Test setup for 30 MHz – 1 GHz Produkte Products Prüfbericht-Nr.: 60338060-001 Appendix 1 Test Report No.: Seite 2 von 4 Page 2 of 4 Produkte Products Prüfbericht-Nr.: 60338060-001 Appendix 1 Test Report No.: Seite 3 von 4 Page 3 of 4 1.1.2 Test setup for 1 GHz – 18 GHz (Performed on axis 3) Produkte Products Prüfbericht-Nr.: 60338060-001 Appendix 1 Test Report No.: Seite 4 von 4 Page 4 of 4