2AOKM-GV23Smart Key

User’s Manual Smart Key FCC: 2AOKM-GV23 IC: 24223-GV23 Model: RT-LXPT003 P/N : RT-G2783 This remote has lock, unlock, Remote Start ,Trunk,Power door release and panic buttons; you can lock and unlock the vehicle doors and Remote Start /Power door release with the remote transmitter. LOCK Button: When you press the LOCK button, it locks all the doors. Once: Some exterior lights flash, all the doors and fuel fill door lock, and the security system sets. Twice:(within five seconds after the first push): Some exterior lights flash, the beeper sounds and verifies the security system is set. UNLOCK Button: Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Once: Some exterior lights flash twice, and the driver’s door and fuel fill door unlocks Twice: Some exterior lights flash twice, and the remaining doors unlock. Remote Start Button: Press and release LOCK and then immediately press and hold this button for at least four seconds to start the vehicle's heating or air conditioning systems and rear window defogger from outside the vehicle using the remote key RUNK Button: Press the trunk release button for approximately one second to unlock and open the trunk Power door release Button: Press the Hatch release button for approximately one second to unlock and open the Power door release PANIC Button: Press and release one time to initiate vehicle locator. The exterior lamps flash and the horn chirps three times. Press and hold the button for at least three seconds to sound the panic alarm. The horn sounds and the turn signals flash for about 30 seconds or until this button is pressed again or the vehicle is started. FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the user’s body and the handset, including the antenna. IC WARNING: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device ADVERTENCIA IC Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis auxdeux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles deprovoquer un fonctionnement indésirable de l'appareil.

Remote Tech LLC Covered Equipment Certification Attestation Letter 8/11/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AOKM-GV23 Remote Tech LLC (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List , the applicant should include an explanation on why the equipment is not “covered” equipment. Remote Tech LLC (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Remote Tech LLC (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: John Strong Title: Company Name: Remote Tech LLC Date: 8/11/2026

Remote Tech LLC * the applicant must designate a contact located in the United States for purposes of acting as the applicant’s agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. U.S. Agent Designation for Service of Process - Certification Attestation Letter 7/10/2026 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2AOKM-GV23 FRN of applicant: 0027073436 Per section 2.911(d)(7) of the FCC rules, [Remote Tech LLC] (“the applicant”) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process: Company Name: Remote Tech LLC FCC Registration Number (FRN): 0027073436 Physical U.S. Company Address: 310 ALDER RD, DOVER DE 19904 USA Contact Person: John Strong Agent Email Address: [email protected] The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed: Agent Signed (if different from Applicant): Signed: Printed name: John Strong Title: Company Name: Remote Tech LLC Date: 8/11/2026 Signed: Printed name: Title: Company Name: Date:

Remote Tech LLC 2026/8/11 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen Acote TechnologyCo., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, John Strong Name, function, signature Telephone: 302-336-8136

Remote Tech LLC 2026/8/11 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (Smart Key/ RT-LXPT003) FCC ID: 2AOKM-GV23 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the required to be submitted with this application be permanently withheld from public review. Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation SPECIFY REASON FOR REQUEST (i.e. the above documents are company proprietary information that could never get into the possession of your competition). Please contact me if there is any information you may need. Sincerely, John Strong

Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 32 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) 7 EUT Constructional Details EUT External Photos Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 33 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 34 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715)

Label : FCC ID: 2AOKM-GV23 IC ID : 24223-GV23 MODEL: RT-LXPT003 PN: RT-G2783

Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 35 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) EUT Internal Photos Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 36 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 37 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 38 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 39 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) ------ End of Report ------ ANT

Report No.: ACT-RF-260701102 This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Cover Page RF Exposure Evaluation Report Applicant: Remote Tech LLC Address of Applicant: 310 ALDER RD, DOVER DE 19904 USA Product Name: Smart Key Model No.: RT-LXPT003 Brand Name: / FCC ID: 2AOKM-GV23 Test Standards: FCC CFR Title 47 Part 2 (§2.1093) KDB 447498 D01 General RF Exposure Guidance v06 Date of Sample Receipt: Jul. 27, 2026 Date of Test: Jul. 28 to Aug. 06, 2026 Date of Report Issue: Aug. 07, 2026 Prepared By: Shenzhen Acote Technology Co., Ltd. Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Winner Zhang / Manager Approved by Aron Wu / Senior Engineer Reviewed by Report No.: ACT-RF-260701102 Shenzhen Acote Technology Co., Ltd. Page 2 of 7 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report Revision History Rev. Issue Date Description V00 Aug. 07, 2026 Initial Release Report No.: ACT-RF-260701102 Shenzhen Acote Technology Co., Ltd. Page 3 of 7 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Table of Contents Cover Page ............................................................................................................................. 1 Report Revision History ........................................................................................................ 2 Table of Contents................................................................................................................... 3 1 Laboratory Introduction .................................................................................................. 4 Laboratory Location................................................................................................................................... 4 1.1 Laboratory Facility ..................................................................................................................................... 4 1.2 Announcement .......................................................................................................................................... 4 1.3 Disclaimer .................................................................................................................................................. 4 1.4 2 Equipment Under Test Information ................................................................................ 5 Application Information .............................................................................................................................. 5 2.1 Product Information ................................................................................................................................... 5 2.2 EUT Technical Parameters ....................................................................................................................... 5 2.3 3 Test Information ............................................................................................................... 6 Test Methodology ...................................................................................................................................... 6 3.1 Additions to, Deviations, or Exclusions from the Method .......................................................................... 6 3.2 Test Mode ................................................................................................................................................. 6 3.3 Worst-case ................................................................................................................................................ 6 3.4 4 Technical requirements specification ............................................................................ 7 Limits ......................................................................................................................................................... 7 4.1 Result ........................................................................................................................................................ 7 4.2 Conclusion ................................................................................................................................................. 7 4.3 Report No.: ACT-RF-260701102 Shenzhen Acote Technology Co., Ltd. Page 4 of 7 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) 1 Laboratory Introduction Laboratory Location 1.1 Company Name: Shenzhen Acote Technology Co., Ltd. Address of Laboratory: Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China. 101, F1, building 15, zhongda 365, Xincheng Road No.9, Songshanhu, Dongguan, Guangdong, China. Website: www.acotelabs.com Email: [email protected] Tel.: +86-0755-2788 9963 Laboratory Facility 1.2 Our company’s laboratory facilities have received accreditation, certification, or authorization from the following organizations:  FCC - Designation No.: CN1450 Shenzhen Acote Technology Co., Ltd. has been certified…

Text truncated - open the document above for the full version.

Antenna Specification Model Name 315MHz Antennal Gain -12.88 dBi Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Manufacture Remote Tech LLC Manufacture Address 310 ALDER RD, DOVER DE 19904 USA Antenna Photo

Report No.: ACT-RF-260701101 This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Cover Page FCC RF Test Report (SRD) Applicant: Remote Tech LLC Address of Applicant: 310 ALDER RD, DOVER DE 19904 USA Product Name: Smart Key Model No.: RT-LXPT003 Brand Name: / FCC ID: 2AOKM-GV23 Test Standards: FCC CFR Title 47 Part 15C (§15.231(a)) Date of Sample Receipt: Jul. 27, 2026 Date of Test: Jul. 28 to Aug. 06, 2026 Date of Report Issue: Aug. 07, 2026 Prepared By: Shenzhen Acote Technology Co., Ltd. Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Winner Zhang / Manager Approved by Aron Wu / Senior Engineer Reviewed by Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 2 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report Revision History Rev. Issue Date Description V00 Aug. 07, 2026 Initial Release Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 3 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Table of Contents Cover Page ............................................................................................................................. 1 Report Revision History ........................................................................................................ 2 Table of Contents................................................................................................................... 3 1 Laboratory Introduction .................................................................................................. 4 Laboratory Location................................................................................................................................... 4 1.1 Laboratory Facility ..................................................................................................................................... 4 1.2 Announcement .......................................................................................................................................... 4 1.3 Disclaimer .................................................................................................................................................. 4 1.4 2 Equipment Under Test Information ................................................................................ 5 Application Information .............................................................................................................................. 5 2.1 Product Information ................................................................................................................................... 5 2.2 EUT Technical Parameters ....................................................................................................................... 5 2.3 3 Test Information ............................................................................................................... 6 Test Methodology ...................................................................................................................................... 6 3.1 Test Result Summary ................................................................................................................................ 6 3.2 Environment of test site ............................................................................................................................. 6 3.3 Measurement Uncertainty ......................................................................................................................... 7 3.4 Description of Support Units ..................................................................................................................... 7 3.5 Additions to, Deviations, or Exclusions from the Method .......................................................................... 7 3.6 Test Instruments List ................................................................................................................................. 8 3.7 4 Test Configuration of EUT ............................................................................................. 10 Test Mode ............................................................................................................................................... 10 4.1 Test Configuration ................................................................................................................................... 10 4.2 Test Setup Block ..................................................................................................................................... 11 4.3 5 Technical requirements specification .......................................................................... 12 Antenna Requirement ............................................................................................................................. 12 5.1 AC Power Line Conducted Emission ...................................................................................................... 13 5.2 20dB Bandwidth ...................................................................................................................................... 14 5.3 Field Strength of Fundamental ..............…

Text truncated - open the document above for the full version.

Report No.: ACT-RF-260701101 Shenzhen Acote Technology Co., Ltd. Page 31 of 39 Project No.: ACT-RF-2607011 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) 6 Test Setup Photos Radiated Spurious Emission Below 1GHz Above 1GHz