2AOKM-HD09BSmart Key

User’s Manual Smart Key FCC ID:2AOKM-HD09B IC:24223-HD09B MODEL:RT-HD094B This remote has lock, unlock, and panic buttons; you can lock and unlock the vehicle doors and trunk/hatch with the remote transmitter. LOCK Button: When you press the LOCK button, it locks all the doors. UNLOCK Button: Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. PANIC Button: When you press the PANIC button, the vehicle will start sounding the horn and flushing the hazard lamp. To stop the alarm, press any button on the electronic key. REMOTE START Button: Press the remote start button twice within 5 seconds. The vehicle will stay in the Remote Start mode for a 15-minute cycle. Press and release remote start button once to exit Remote Start mode. TRUNK Button: Pressing the button opens and closes the trunk. FCC COMPLIANCE STATEMENT: 1.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC WARNING: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device ADVERTENCIA IC Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis auxdeux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles deprovoquer un fonctionnement indésirable de l'appareil.

Rev 1/26/2023 Remote Tech LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 9/7/2026 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AOKM-HD09B Applicant FRN: 0027073436 Remote Tech LLC (“the applicant”) certifies that, as of the date of the filing of the application, Remote Tech LLC is our designated U.S. agent for service of process for the above referenced FCC ID. Remote Tech LLC accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Remote Tech LLC accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Remote Tech LLC U.S. Agent FRN: 0027073436 Address: 310 ALDER RD, DOVER DE 19904 USA Contact Person: John Strong Tel.: 302-336-8136 Email: [email protected] Sincerely, Remote Tech LLC John Strong

Remote Tech LLC Rev 2026-04-24 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 9/9/2026 Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) FCC ID: 2AOKM-HK54 Part 2.911(d)(5)(i) [Remote Tech LLC] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment and does not contain anti-virus software or cybersecurity software prohibited from receiving an equipment authorization pursuant to 47 CFR 2.903, KDB 986446 D01 Covered Equipment Guidance, and FCC Covered List (www.fcc.gov/supplychain/coveredlist). Part 2.911(d)(5)(ii) [Remote Tech LLC] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Signed: Printed name: John Strong Title: Manager Company Name: Remote Tech LLC Date: 9/9/2026

C:\Users\ZJ01\Desktop\新建文件夹 (2)\遥控器\ACT-RF-2608014 遥控器 RT-HD094B FCC ID\letter\FCC\FCC POA Letter.docx Remote Tech LLC Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Date: 9/7/2026 SUBJECT: FCC Application for FCCID : 2AOKM-HD09B To Whom It May Concern: We, the undersigned, hereby authorize Winner Zhang at Shenzhen Acote TechnologyCo., Ltd. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by _ Winner Zhang _ on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, John Strong /Manager

Rev 11/20/07 Remote Tech LLC Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AOKM-HK54 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name 1. Schematic 2. Block Diagram; 3. Circuit Description, 4. BOM SCH Block Operational Description BOM The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name* (ie- External Photos, Internal Photos, Test Setup Photos, Manual) (ie- “1100_external photos.pdf”) Sincerely, John Strong /Manager

Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 31 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) 7 EUT Constructional Details EUT External Photos Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 32 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 33 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715)

Label : Size: 33*25 mm FCC ID:2AOKM-HD09B IC:24223-HD09B MODEL:RT-HD094B P/N: RT-HDG94N

Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 34 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) EUT Internal Photos Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 35 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 36 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 37 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 38 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) ------ End of Report ------ ANT

Report No.: ACT-RF-260801402 This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Cover Page RF Exposure Evaluation Report Applicant: Remote Tech LLC Address of Applicant: 310 ALDER RD, DOVER DE 19904 USA Product Name: Smart Key Model No.: RT-HD094B Brand Name: / FCC ID: 2AOKM-HD09B Test Standards: FCC CFR Title 47 Part 2 (§2.1093) KDB 447498 D01 General RF Exposure Guidance v06 Date of Sample Receipt: Aug. 19, 2026 Date of Test: Aug. 20 to 27, 2026 Date of Report Issue: Aug. 28, 2026 Prepared By: Shenzhen Acote Technology Co., Ltd. Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Winner Zhang / Manager Approved by Aron Wu / Senior Engineer Reviewed by Report No.: ACT-RF-260801402 Shenzhen Acote Technology Co., Ltd. Page 2 of 7 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report Revision History Rev. Issue Date Description V00 Aug. 28, 2026 Initial Release Report No.: ACT-RF-260801402 Shenzhen Acote Technology Co., Ltd. Page 3 of 7 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Table of Contents Cover Page ............................................................................................................................. 1 Report Revision History ........................................................................................................ 2 Table of Contents................................................................................................................... 3 1 Laboratory Introduction .................................................................................................. 4 Laboratory Location................................................................................................................................... 4 1.1 Laboratory Facility ..................................................................................................................................... 4 1.2 Announcement .......................................................................................................................................... 4 1.3 Disclaimer .................................................................................................................................................. 4 1.4 2 Equipment Under Test Information ................................................................................ 5 Application Information .............................................................................................................................. 5 2.1 Product Information ................................................................................................................................... 5 2.2 EUT Technical Parameters ....................................................................................................................... 5 2.3 3 Test Information ............................................................................................................... 6 Test Methodology ...................................................................................................................................... 6 3.1 Additions to, Deviations, or Exclusions from the Method .......................................................................... 6 3.2 Test Mode ................................................................................................................................................. 6 3.3 Worst-case ................................................................................................................................................ 6 3.4 4 Technical requirements specification ............................................................................ 7 Limits ......................................................................................................................................................... 7 4.1 Result ........................................................................................................................................................ 7 4.2 Conclusion ................................................................................................................................................. 7 4.3 Report No.: ACT-RF-260801402 Shenzhen Acote Technology Co., Ltd. Page 4 of 7 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) 1 Laboratory Introduction Laboratory Location 1.1 Company Name: Shenzhen Acote Technology Co., Ltd. Address of Laboratory: Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China. 101, F1, building 15, zhongda 365, Xincheng Road No.9, Songshanhu, Dongguan, Guangdong, China. Website: www.acotelabs.com Email: [email protected] Tel.: +86-0755-2788 9963 Laboratory Facility 1.2 Our company’s laboratory facilities have received accreditation, certification, or authorization from the following organizations:  FCC - Designation No.: CN1450 Shenzhen Acote Technology Co., Ltd. has been certified by t…

Text truncated - open the document above for the full version.

Report No.: ACT-RF-260801401 This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Cover Page FCC RF Test Report (SRD) Applicant: Remote Tech LLC Address of Applicant: 310 ALDER RD, DOVER DE 19904 USA Product Name: Smart Key Model No.: RT-HD094B Brand Name: / FCC ID: 2AOKM-HD09B Test Standards: FCC CFR Title 47 Part 15C (§15.231(a)) Date of Sample Receipt: Aug. 19, 2026 Date of Test: Aug. 20 to 27, 2026 Date of Report Issue: Aug. 28, 2026 Prepared By: Shenzhen Acote Technology Co., Ltd. Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Winner Zhang / Manager Approved by Aron Wu / Senior Engineer Reviewed by Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 2 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Report Revision History Rev. Issue Date Description V00 Aug. 28, 2026 Initial Release Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 3 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) Table of Contents Cover Page ............................................................................................................................. 1 Report Revision History ........................................................................................................ 2 Table of Contents................................................................................................................... 3 1 Laboratory Introduction .................................................................................................. 4 Laboratory Location................................................................................................................................... 4 1.1 Laboratory Facility ..................................................................................................................................... 4 1.2 Announcement .......................................................................................................................................... 4 1.3 Disclaimer .................................................................................................................................................. 4 1.4 2 Equipment Under Test Information ................................................................................ 5 Application Information .............................................................................................................................. 5 2.1 Product Information ................................................................................................................................... 5 2.2 EUT Technical Parameters ....................................................................................................................... 5 2.3 3 Test Information ............................................................................................................... 6 Test Methodology ...................................................................................................................................... 6 3.1 Test Result Summary ................................................................................................................................ 6 3.2 Environment of test site ............................................................................................................................. 6 3.3 Measurement Uncertainty ......................................................................................................................... 7 3.4 Description of Support Units ..................................................................................................................... 7 3.5 Additions to, Deviations, or Exclusions from the Method .......................................................................... 7 3.6 Test Instruments List ................................................................................................................................. 8 3.7 4 Test Configuration of EUT ............................................................................................. 10 Test Mode ............................................................................................................................................... 10 4.1 Test Configuration ................................................................................................................................... 10 4.2 Test Setup Block ..................................................................................................................................... 11 4.3 5 Technical requirements specification .......................................................................... 12 Antenna Requirement ............................................................................................................................. 12 5.1 AC Power Line Conducted Emission ...................................................................................................... 13 5.2 20dB Bandwidth ...................................................................................................................................... 14 5.3 Field Strength of Fundamental ...................…

Text truncated - open the document above for the full version.

Antenna Specification Model Name 433.92MHz Antennal Gain -12.88 dBi Polarization Horizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance 50 Ohm Manufacture Remote Tech LLC Manufacture Address 310 ALDER RD, DOVER DE 19904 USA Antenna Photo

Report No.: ACT-RF-260801401 Shenzhen Acote Technology Co., Ltd. Page 30 of 38 Project No.: ACT-RF-2608014 Room 719, Excellence Times Building, No. 27, Xinqiao 3rd Road, Xinqiao Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong Province, China Report Template No.: ACT-4-FM-RF-001 Version A1 (20260715) 6 Test Setup Photos Radiated Spurious Emission Below 1GHz Above 1GHz