2AOWK-3112Mobile Phone

(1} This device may not cause harmful interference, and (2) t his device must accept any interference received, including interference that may cause undesired operation. This Product meets the government's requirements for exposure to radio waves. The guidelines are b ased on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific s tudies. The standards include a substantial safety margin designed to assure the safety of all persons r egardless of age or health. FCC RF Ex posure Information and Statement the SAR limit of USA (FCC) is1 .6 W/kg averaged over one gram of this Device GQ3112(FCC ID: 2AOWK-3112) has been tested against this SAR limit . SAR information on this can be viewed on-line at http://www.fcc.gov/oet/ea/fccid/. Please use the device FCC ID number for search. This device was tested for typical operations 1 0mm from the body. To maintain compliance with FCC RF exposure requirements, 10mm separation distance should. maintained to t he user's bodies NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures 59 IC Caution EN This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference. 2.This device m ust accept any interference, including interference that may cause undesired operation of the device. FR L'emetteur/recepteur exempt de licence contenu dans le present appareil est conforme aux CNR d'lnnovation, Sciences e t Developpement economique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: 1.L'a ppareil ne doit pas produire de b rouillage; 2 .L'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en c ompromeltre le fonctionnement. 60 - - Reorient or relocate the receiving antenna. - - Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from t hat to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Function Operation Frequency Max RF outputpower: BT(BR+EDR) 2402MHz–2480MHz <10dBm BLE 2402MHz–2480MHz <10dBm WIFI 802.11b/g/ n(HT20,HT40) 802.11b/g/n(20MHz): 2412~2472MHz; 802.11n(40MHz):2422~2462MHz <20dBm Wi-Fi 5.2G(802.11a/n20 /n40/ac20/ac40/a c80) 802.11a/ n20/ac20:5180MHz~5240MHz 802.11 n40/ac40: 5190MHz~5230MHz 802.11ac80:5210MHz <20dBm Wi-Fi 5.8G(802.11a/n20 /n40/ac20/ac40/a c80) 802.11a/ n20/ac20:5745MHz~5825MHz 802.11 n40/ac40: 5755MHz~5795MHz 802.11ac80:5775MHz <13.98dBm GSM/GPRS/EGP RS 900 TX(Uplink):880Mϋ915MHZ; RX(Downlink):925M ϋ960MHZ <36dBm GSM/GPRS/EGP RS 1800 TX(Uplink):1710Mϋ1785MHZ; RX(Downlink):1805M ϋ1880MHZ <33dBm WCDMA B1 TX(Uplink):1920-1980MHz; RX(Downlink):2110-2170MHz <25.7dBm WCDMA B8 TX(Uplink): 880-915MHz; RX(Downlink):925-960MHz <25.7dBm LTE FDD B1 TX(Uplink):1920-1980MHz; RX(Downlink):2110-2170MHz <25dBm LTE FDD B3 TX(Uplink) :1710-1785MHz; RX(Downlink):1805-1880MHz <25dBm LTE FDD B7 TX(Uplink) :2500-2570MHz; RX(Downlink):2620-2690MHz <25dBm LTE FDD B8 TX(Uplink): 880MHz to 915 MHz RX(Downlink): 925 MHz to 960 MHz <25dBm LTE FDD B20 TX(Uplink): 832MHz~862MHz; RX(Downlink): 791MHz~821MHz <25dBm LTE FDD B28 TX(Uplink): 703 MHz to 748MHz R X(Downlink): 758 MHz to 803 MHz <25dBm FM Rx(Downlink): 87.5MHz~108MHz -- GPS Rx(Downlink): 1.57542GHz -- NFC 13.56MHz <60dBuA/m@10 m

Shenzhen Gotron Electronic CO.,LTD. Family models difference declaration Mobile Phone Model: GQ3112, Armor X12, Armor X12 Pro, Armor X12 Lite, Armor X12 Plus, Armor X12S, Armor X12P, Armor X12T, Armor X12E Difference declaration: All the model are the same circuit and RF module,only color and model name are different. Regards, Signature Yongbin Tang/ Manager Date/City: 2023-08-15 / Shenzhen Phone: 0755-8389 5989 Fax: 0755-8389 5909 E-mail: [email protected]

(Shenzhen Gotron Electronic CO.,LTD.) (2023.08.15) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for (FCC ID:2AOWK-3112) [Shenzhen Gotron Electronic CO.,LTD.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, tangyongbin (Shenzhen Gotron Electronic CO.,LTD.) (2023.08.15) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for (FCC ID: 2AOWK-3112) [Shenzhen Gotron Electronic CO.,LTD.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, tangyongbin

THREE STONES MEDIA LLC U.S. Agent Letter of Attestation To: Federal Communications Commission 7435 Oakland Mills Road, Columbia, MD 21046, USA Date: 8/10/2023 Ref: Attestation Statement – Part2.911(d)(7) filing FCC ID：2AOWK-3112 Shenzhen Gotron Electronic CO.,LTD (“the applicant”) certifies that, as of the date of the filing of the application, THREE STONES MEDIA LLC(“the agent”) is our designated U.S. agent for service of process for the abovereference FCC ID. The applicant accepts to maintain an agent for service of process in the United States forno less than one year after either the grantee has permanently terminated all marketing and importation of theapplicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicialproceeding involving the equipment, whichever is later. The applicant further acknowledges it is ourresponsibility to inform the FCC whenever the agent information changes. THREE STONES MEDIA LLC ("the agent) understand it is the agent's obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address. Designated U.S. Agent Company Name: THREE STONES MEDIA LLC FRN: 0033401761 GC: 2A99E Address: 1200 Broadway St. APT 329, Los Angeles, CA90015 Signature: Contact Person: Sijie Zhang Tel: +1 267 909 3692 Email: [email protected] Applicant Company Name: Shenzhen Gotron Electronic CO.,LTD Address: 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China Signature: Contact Person: Yongbin Tang Tel: +86-755-83895989 Email: [email protected]

Shenzhen Gotron Electronic CO.,LTD. Agent Authorization Letter (2023-08-15) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park Sanwei, Xixiang, Bao'an District, Shenzhen, Guangdong, China Alex.li [email protected] to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Yongbin Tang/ Manager Date/City: 2023-08-15 / Shenzhen Phone: 0755-8389 5989 Fax: 0755-8389 5909 E-mail: [email protected]

Shenzhen Gotron Electronic CO.,LTD. Long Term Confidentiality Request Letter (2023-08-15) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR Product: Mobile Phone Model: GQ3112, Armor X12, Armor X12 Pro, Armor X12 Lite, Armor X12 Plus, Armor X12S, Armor X12P, Armor X12T, Armor X12E FCC ID: 2AOWK-3112 To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the  Schematic Diagram  Block Diagram  Part List / BOM List / PCB Layout  Operational Description  Tune-up Procedure  FCC Software Configuration Control Declaration  FCC Software Security Requirements for UNII devices Required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Please contact me if there is any information you may need. Sincerely, Yongbin Tang / Manager Date/City: 2023-08-15 / Shenzhen Phone: 0755-8389 5989 Fax: 0755-8389 5909 E-mail: [email protected]

Shenzhen Gotron Electronic CO.,LTD. Short Term Confidentiality Request Letter (2023-08-15) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Short Term Confidentiality Request For Product: Mobile Phone Model: GQ3112, Armor X12, Armor X12 Pro, Armor X12 Lite, Armor X12 Plus, Armor X12S, Armor X12P, Armor X12T, Armor X12E FCC ID: 2AOWK-3112 To Whom It May Concern: In accordance with sections 0.457 and 0.459 of CFR 47, < Shenzhen Gotron Electronic CO.,LTD. >. requests short-term Confidentiality of following sections of this application for a period of 180 days after grant is issued. Test setup photos External photos Internal photos User’s manual These documents contain detailed system and equipment descriptions and related information about the product, which < Shenzhen Gotron Electronic CO.,LTD. > considers to be proprietary, confidential, and a custom design and otherwise, would not release to the general public. Since this design is a basis from which future technological products will evolve, < Shenzhen Gotron Electronic CO.,LTD. > feels that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give our competitors an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Yongbin Tang / Manager Date/City: 2023-08-15 / Shenzhen Phone: 0755-8389 5989 Fax: 0755-8389 5909 E-mail: [email protected]

ATTACHMENT PHOTOGRAPHS OF EUT Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Adapter 1# Photo 9 Adapter 2#

Photo 10 Photo 11 Photo 12 Photo 13 Photo 14 Photo 15 Photo 16 Photo 17 Photo 18 Photo 19 Photo 20 Photo 21 Photo 22 Photo 23 Photo 24 2/3/4G Main Ant 4G Div Ant FM RX Ant Photo 25 Photo 26 BT/WIFI Ant

Page 1 of 242 Report No.: S23060904203001 FCC SAR EVALUATION REPORT In accordance with the requirements of FCC 47 CFR Part 2(2.1093), ANSI/IEEE C95.1-1992 and IEEE Std 1528-2013 Product Name： Mobile Phone Brand Name： ulefone Model Name： GQ3112 Family Model： Armor X12, Armor X12 Pro, Armor X12 Lite, Armor X12 Plus, Armor X12S, Armor X12P, Armor X12T, Armor X12E Report No.： S23060904203001 FCC ID： 2AOWK-3112 Prepared for Shenzhen Gotron Electronic CO.,LTD 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community, Xixiang Street, Bao'an District, Shenzhen 518126 P.R.China. Tel. 400-800-6106, 0755-2320 0050, 0755-2320 0090 Website: http://www.ntek.org.cn Page 2 of 242 Report No.: S23060904203001 TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Gotron Electronic CO.,LTD Address .................................. : 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China Manufacturer's Name .......... : Shenzhen Gotron Electronic CO.,LTD Address .................................. : 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China Product description Product name ........................ : Mobile Phone Brand Name ......................... : ulefone Model and/or type reference .............................. : GQ3112 Family Model ......................... : Armor X12, Armor X12 Pro, Armor X12 Lite, Armor X12 Plus, Armor X12S, Armor X12P, Armor X12T, Armor X12E Standards ............................. : FCC 47 CFR Part 2(2.1093) ANSI/IEEE C95.1-1992 IEEE Std 1528-2013 Published RF exposure KDB procedures This device described above has been tested by Shenzhen NTEK. In accordance with the measurement methods and procedures specified in IEEE Std 1528-2013 and KDB 865664 D01. Testing has shown that this device is capable of compliance with localized specific absorption rate (SAR) specified in FCC 47 CFR Part 2(2.1093) and ANSI/IEEE C95.1-1992. The test results in this report apply only to the tested sample of the stated device/equipment. Other similar device/equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. This report shall not be reproduced except in full, without the written approval of Shenzhen NTEK, this document may be altered or revised by Shenzhen NTEK, personal only, and shall be noted in the revision of the document. Test Sample Number ............................. S230609042003 Date of Test Date (s) of performance of tests .............. : Jun. 20, 2023 ~ Jul. 03, 2023 Date of Issue ........................................... : Jul. 31, 2023 Test Result ............................................... : Pass Prepared By (Test Engineer) : (Jack Li) Approved By (Lab Manager) : (Alex Li) Page 3 of 242 Report No.: S23060904203001 ※ ※ Revision History ※ ※ REV. DESCRIPTION ISSUED DATE REMARK Rev.1.0 Initial Test Report Release Jul. 31, 2023 Jack Li Page 4 of 242 Report No.: S23060904203001 TABLE OF CONTENTS 1. General Information ............................................................................................ 6 1.1. RF exposure limits .................................................................................... 6 1.2. Statement of Compliance ........................................................................ 7 1.3. EUT Description ....................................................................................... 7 1.4. Test specification(s) .................................................................................. 8 1.5. Ambient Condition ................................................................................... 9 2. SAR Measurement System ................................................................................. 10 2.1. SATIMO SAR Measurement Set-up Diagram .......................................... 10 2.2. Robot ..................................................................................................... 11 2.3. E-Field Probe .......................................................................................... 12 2.3.1. E-Field Probe Calibration ................................................................. 12 2.4. SAM phantoms ...................................................................................... 13 2.4.1. Technical Data .................................................................................. 14 2.5. Device Holder ........................................................................................ 15 2.6. Test Equipment List ................................................................................ 16 3. SAR Measurement Procedures .......................................................................... 19 3.1. Power Reference ................................................................................... 19 3.2. Area scan & Zoom scan .......................................................................... 19 3.3. Description of interpolation/extrapolation scheme .............................. 21 3.4. Volumetric Scan ..................................................................................... 21 3.5. Power Drift ............................................................................................ 21 4. System Verification Procedure .......................................................................... 22 4.1. Tissue Verification ................................................................................. 22 4.1.1. Tissue Dielectric Parameter Check Results ...................................... 23 4.2. System Verification Procedure .............................................................. 24 4.2.1. System Verification Results .............................................................. 25 5. SAR Measu…

Text truncated - open the document above for the full version.

Page 181 of 242 Report No.: S23060904203001 Page 182 of 242 Report No.: S23060904203001 Page 183 of 242 Report No.: S23060904203001 Page 184 of 242 Report No.: S23060904203001 Page 185 of 242 Report No.: S23060904203001 Page 186 of 242 Report No.: S23060904203001 Page 187 of 242 Report No.: S23060904203001 Page 188 of 242 Report No.: S23060904203001 Page 189 of 242 Report No.: S23060904203001 Page 190 of 242 Report No.: S23060904203001 Page 191 of 242 Report No.: S23060904203001 Page 192 of 242 Report No.: S23060904203001 Page 193 of 242 Report No.: S23060904203001 Page 194 of 242 Report No.: S23060904203001 Page 195 of 242 Report No.: S23060904203001 Page 196 of 242 Report No.: S23060904203001 Page 197 of 242 Report No.: S23060904203001 Page 198 of 242 Report No.: S23060904203001 Page 199 of 242 Report No.: S23060904203001 Page 200 of 242 Report No.: S23060904203001 Page 201 of 242 Report No.: S23060904203001 Page 202 of 242 Report No.: S23060904203001 Page 203 of 242 Report No.: S23060904203001 Page 204 of 242 Report No.: S23060904203001 Page 205 of 242 Report No.: S23060904203001 Page 206 of 242 Report No.: S23060904203001 Page 207 of 242 Report No.: S23060904203001 Page 208 of 242 Report No.: S23060904203001 Page 209 of 242 Report No.: S23060904203001 Page 210 of 242 Report No.: S23060904203001 Page 211 of 242 Report No.: S23060904203001 Page 212 of 242 Report No.: S23060904203001 Page 213 of 242 Report No.: S23060904203001 Page 214 of 242 Report No.: S23060904203001 Page 215 of 242 Report No.: S23060904203001 Page 216 of 242 Report No.: S23060904203001 Page 217 of 242 Report No.: S23060904203001 Page 218 of 242 Report No.: S23060904203001 Page 219 of 242 Report No.: S23060904203001 Page 220 of 242 Report No.: S23060904203001 Page 221 of 242 Report No.: S23060904203001 Page 222 of 242 Report No.: S23060904203001 Page 223 of 242 Report No.: S23060904203001 Page 224 of 242 Report No.: S23060904203001 Page 225 of 242 Report No.: S23060904203001 Page 226 of 242 Report No.: S23060904203001 Page 227 of 242 Report No.: S23060904203001 Page 228 of 242 Report No.: S23060904203001 Page 229 of 242 Report No.: S23060904203001 Page 230 of 242 Report No.: S23060904203001

OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page1 OTA TEST REPORT Applicant Shenzhen General Test System Co., Ltd ProductRayZone1800 Issue Date June21,2023 Shenzhen Fu Bang Wireless Technology Co., Ltd. tested the above equipment in accordance with the requirements in ANTI/IEEE Std 149-2008.The test results show that the equipment tested is capable of demonstrating compliance with theRequirements as documented in this report. Prepared by: Lunkang Yan Approved by: Zhanghong Lai Shenzhen Fu Bang Wireless Technology Co., Ltd. Room 302, lianjian Industry Part, Huarong road, Longhua District, Shenzhen, P.R. China OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page2 1. Test Laboratory 1.1 Notes of the Test report This report shall not be reproduced in full or partial. The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. Measurement Uncertainties were not taken into account and are published for informational purposesonly. This report is written to support regulatory compliance of applicable standards stated above. 1.2 Test facility GTS1800Microwave Anechoic Chamber ：testing frequency ranges from 600MHz to 6GHz . 1.3 Testing Location Company: Shenzhen Maya Communication Equipment Co. LTD Address: 2nd Floor, Building 1, Guanghui Science Park, Longhua New District, ShenzhenShenzhen, P.R. China Contact: Feng Guojun Telephone: 13425109220 E-mail: [email protected] 1.4 Laboratory Environment 2. General Description of Equipment under Test Temperature Min.= 19°C, Max.=25°C Relative humidity Min.=40%，Max.=72% Shield effect 0.6-7GHz >100dB Ground resistance <0.5Ω OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page3 2.1 Applicant and Manufacturer information Applicant Name Shenzhen General Test System Co., Ltd Applicant address Building C-A7 Suite 805,2190 Liuxian Avenue, Nanshan District, Shenzhen, P.R. China Manufacturer Name Shenzhen General Test System Co., Ltd Manufacturer address Building C-A7 Suite 805,2190 Liuxian Avenue, Nanshan District, Shenzhen, P.R. China 2.2 General information EUT Description Product Name RayZone1800 Model MVG HW Version RayZone1800 V1.0 SW Version MaxSign 100 Antenna Type PCB Antenna Antenna Manufacturer Shenzhen Maya Communication Equipment Co. LTD Test Frequency 700MHz-5.8GHz 2.3 Applied Standards According to the specifications of the manufacturer, it must comply with the requirements of the following standards: Test Method: ANSI/IEEE Std 149-2008 3. Test Conditions 3.1 Test Configuration The method is used to measure the antenna 3D GAIN of EUT in OTA qualified anechoic chamber. Equipment Under Test (EUT) geometry centre vertical projection at the centre of platform, the distance from EUT to measurement antenna is 1m. 3.2 Test Measurement Spherical coordinate system OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page4 Figure 1 Test coordinate system Note: Theta is from 0-180degree.Phi is from EUT and record the Date, the step of rotation is 15 degree. Test Setup 4. Test Results 4.1 Gain and Efficiency OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page5 OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page6 OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page7 5. Equipment List Type of Equipment Manufacture Model Number Network Analyzer Key sight E5071C Switch control System MVG RayZone1800 Software MVG MaxSign 100 Patten Measurement software OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page8 ANNEX A 3-D Patten Plots OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page9 OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page10 NFC antenna size diagram ANNEX B: The EUT Appearance and Test Configuration B.1 EUT Appearance OTA Test Report Shenzhen Fu Bang Wireless Technology Co., Ltd. This report shall not be reproduced except in full, without the written approval of Shenzhen Fu Bang Wireless Technology Co., Ltd. Page11

Report No.: S23060904201001 Version.1.3 Page 1 of 95 RADIO TEST REPORT FCC ID: 2AOWK-3112 Product: Mobile Phone Trade Mark: ulefone Model No.: GQ3112 Family Model: Armor X12, Armor X12 Pro, Armor X12 Lite, Armor X12 Plus, Armor X12S, Armor X12P, Armor X12T, Armor X12E Report No.: S23060904201001 Issue Date: Aug 02, 2023 Prepared for Shenzhen Gotron Electronic CO.,LTD. 7B01, Building A, Block 1, Anhongji Tianyao Plaza, Longhua District, Shenzhen City, Guangdong Province China Prepared by Shenzhen NTEK Testing Technology Co., Ltd. 1/F, Building E, Fenda Science Park, Sanwei Community,Xixiang StreetBao’an District, Shenzhen 518126 P.R. China Tel. 400-800-6106, 0755-2320 0050, 0755-2320 0090 Website: http://www.ntek.org.cn Report No.: S23060904201001 Version.1.3 Page 2 of 95 Table of Contents Page 1 TEST RESULT CERTIFICATION ...................................................................................................................... 3 2 SUMMARY OF TEST RESULTS ......................................................................................................................... 4 3 FACILITIES AND ACCREDITATIONS ............................................................................................................. 5 3.1 FACILITIES ..................................................................................................................................................... 5 3.2 LABORATORY ACCREDITATIONS AND LISTINGS ................................................................................. 5 3.3 MEASUREMENT UNCERTAINTY ............................................................................................................... 5 4 GENERAL DESCRIPTION OF EUT .................................................................................................................. 6 5 DESCRIPTION OF TEST MODES...................................................................................................................... 8 6 SETUP OF EQUIPMENT UNDER TEST ........................................................................................................... 9 6.1 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ....................................................................... 9 6.2 SUPPORT EQUIPMENT ............................................................................................................................... 10 6.3 EQUIPMENTS LIST FOR ALL TEST ITEMS .............................................................................................. 11 7 TEST REQUIREMENTS .................................................................................................................................... 13 7.1 CONDUCTED EMISSIONS TEST ............................................................................................................... 13 7.2 RADIATED SPURIOUS EMISSION ............................................................................................................ 16 7.3 NUMBER OF HOPPING CHANNEL ........................................................................................................... 25 7.4 HOPPING CHANNEL SEPARATION MEASUREMENT ........................................................................... 26 7.5 AVERAGE TIME OF OCCUPANCY (DWELL TIME)................................................................................. 27 7.6 20DB BANDWIDTH TEST ........................................................................................................................... 29 7.7 PEAK OUTPUT POWER .............................................................................................................................. 30 7.8 CONDUCTED BAND EDGE MEASUREMENT ......................................................................................... 31 7.9 SPURIOUS RF CONDUCTED EMISSION .................................................................................................. 32 7.10 ANTENNA APPLICATION .......................................................................................................................... 33 7.11 FREQUENCY HOPPING SYSTEM (FHSS) EQUIPMENT REQUIREMENTS.......................................... 34 8 TEST RESULTS ................................................................................................................................................... 35 8.1 DWELL TIME ................................................................................................................................................... 35 8.2 MAXIMUM CONDUCTED OUTPUT POWER .......................................................…

Text truncated - open the document above for the full version.