2APXHIGB5GINFINITY GAME BOARD

Grantee FRN: 0027557156 0033928052

7 / 15 /202 4

Texture on the plastic cover YS 1283A (same as on IGT-32) GLOSS LAST REVISION: 6.4.24 DESIGNER - HK TEAM IGB-I-301202 INFINITY® GAME BOARD - LEGAL ENGRAVING - COPYRIGHT LABEL - ETL LABEL - SERIAL NUMBER LABEL engraving copyright label serial number label ETL label ETL label IGB-I-301202EZQZK-0824-000000 IGB-I-301202 EZQZK-0824-000000 FCC Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Énoncé de la FCC Ce dispositif est conforme à la section 15 des règlements de la FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) le dispositif ne doit pas causer d’interférence nuisible et (2) le dispositif doit pouvoir supporter toute interférence, quelle qu’elle soit, y compris les interférences pouvant causer des effets non désirés. Attention : Tout changement apporté à ce dispositif, non approuvé expressément par la partie responsable de la conformité pourrait annuler le droit d’utilisation du propriétaire. Declaraciones de la FCC Este dispositivo cumple con la Parte 15 de las Reglas de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) este dispositivo no puede causar interferencias, (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas las intererencias que puedan causer un funcionamiento no deseado. Advertencia: los cambios o modificaciones en esta unidad que no estén expresamente aprobados por la parte responsable del cumplimento pueden anular la autoridad del usuario para operar el equipo. The following symbols are used in labels on the game to draw attention to potentially hazardous situations: Les symboles suivants apposés sur la console visent à attirer l’attention sur des situations potentiellement dangereuses: Los siguientes simbolos se utilizan en las etiquetes del juego para llamar la atención sobre situaciones potencialmente peligrosas: WARNING: Failure to avoid the risk may result in death or serious injury. MISE EN GARDE: Le non-respect des mesures de sécurité pourrait entraîner des blessures graves ou mortelles. ADVERTENCIA: si no se evita el riesgo, se pueden producir lesiones graves o incluso la muerte. ELECTRIC SHOCK HAZARD: Disconnect power before removing cover. Should only be done by a qualified operator. RISQUE DE CHOC ÉLECTRIQUE: Débrancher l’appareil avant de retirer le couvercle. Doit être effectué par un technicien qualifié. PELIGRO DE DESCARGA ELÉCTRICA: Desconecte la corriente antes de quitar la tapa. Solo debe hacerlo un operador calificado. INPUT: DC 12V, 3A PUISSANCE D’ENTRÉE: CC 12 V, 3A POTENCIA ENTRADA: DC 12V, 3A SAFETY PRECAUTIONS / PRÉCAUTIONS DE SÉCURITÉ / PRECAUCIONES DE SEGURIDAD CAN ICES-003 (B)/ NMB-003 (B) 5014826 A/V I.C.T.E. TASTEMAKERS, LLC. 51 NE 24th Street, Suite 202, Miami, Florida FL 33137 www.tastemakersllc.com ©2024 Tastemakers, LLC. All rights reserved / Tous les droits sont réservés / Todos los derechos reservados FCC ID: 2APXHIGB5G IC: 24128-IGB5G IGB-I-301202 INFINITY® GAME BOARD MADE IN CHINA / FABRIQUÉ EN CHINE / FABRICADO EN CHINA TM WWW.INFINITYGAMETABLE.COM © 2024 Tastemakers, LLC. All rights reserved /PUF

5IJT
XPVME
CF
B
QMBTUJD
MBCFM
XJUI
B
QFSNBOFOU
BEIFTJWF













5IF
MBCFM
JT
QMBDFE
PO
UIF
CBDL
PG
UIF
UBCMF

UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0036 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. SAR EVALUATION REPORT FCC 47 CFR § 2.1093 IEEE Std. 1528-2013 For INFINITY GAME BOARD FCC ID: 2APXHIGB5G Model: IGB-I-301202 Report Number: 4791327949.2-SAR-1 Issued Date: June 23, 2024 Prepared for WF Tastemakers Trading Limited Unit 05 and unit 06, 6th Floor, Greenfield Tower Concordia Plaza, 1 Science Museum Road, TST East, Hong Kong Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi-Tech Development Zone Dongguan, People’s Republic of China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4791327949.2-SAR-1 Page 2 of 30 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0036 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 June 23, 2024 Initial Issue \ Note: 1.This test report is only published to and used by the applicant, and it is not for evidence purpose in China. 2. The measurement result for the sample received is <Pass> according to < IEEE Std. 1528> when < Simple Acceptance> decision rule is applied. REPORT NO.: 4791327949.2-SAR-1 Page 3 of 30 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0036 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Table of Contents 1. Attestation of Test Results .......................................................................................................... 5 2. Test Specification, Methods and Procedures ............................................................................ 6 3. Facilities and Accreditation......................................................................................................... 7 4. SAR Measurement System & Test Equipment ........................................................................... 8 4.1. SAR Measurement System ............................................................................................................ 8 4.2. SAR Scan Procedures .................................................................................................................... 9 4.3. Test Equipment ............................................................................................................................ 12 5. Measurement Uncertainty ......................................................................................................... 13 6. Device Under Test (DUT) Information ....................................................................................... 14 6.1. DUT Description ........................................................................................................................... 14 6.2. Wireless Technology .................................................................................................................... 14 6.3. Antenna Gain ............................................................................................................................... 14 7. Conducted Output Power Measurement and tune-up tolerance ............................................ 15 7.1. Power measurement result of 2.4GHz Wi-Fi. ................................................................................ 15 7.2. Power measurement result of 5GHz Wi-Fi. ................................................................................... 16 7.3. Duty cycle: .................................................................................................................................... 17 8. Test Configuration ..................................................................................................................... 18 8.1. Wi-Fi Test Configuration ............................................................................................................... 18 8.1.1. Initial Test Position Procedure ............................................................................................... 18 8.1.2. Initial Test Configuration Procedure ....................................................................................... 18 8.1.3. Sub Test Configuration Procedure......................................................................................... 18 8.1.4. 2.4GHz Wi-Fi SAR Test Procedures ...................................................................................... 19 8.1.5. 5GHz Wi-Fi SAR Test Procedures......................................................................................... 20 8.1.6. OFDM Transmission Mode and SAR Test Channel Selection ............................................... 21 9. RF Exposure Conditions ........................................................................................................... 22 9.1. SAR exclusion analysis ................................................................................................................ 25 10. Dielectric Property Measurements & System Check ............................................................... 26 10.1. Dielectric Property Measurements ............................................................................................ 26 REPORT NO.: 4791327949.2-SAR-1 Page 4 of 30 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0036 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. 10.2. System Check .................................................................................................…

Text truncated - open the document above for the full version.

. Measurement Report for Device, , , UID 0 -, Channel 0 (2450.000MHz) Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, N/A x N/A x N/A Dipole Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL , CW, 0-- 2450.000, 0 7.98 1.86 40.1 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - xxxx HBBL-600-10000 Charge:xxxx, 2024-Jun-12 EX3DV4 - SN7733, 2024-02-21 DAE4 Sn1739, 2024-01-23 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 40.0 x 80.0 30.0 x 30.0 x 30.0 Grid Steps [mm] 10.0 x 10.0 5.0 x 5.0 x 1.5 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.5 MAIA N/A N/A Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-06-12, 12:15 2024-06-12, 12:24 psSAR1g [W/kg] 4.85 5.04 psSAR10g [W/kg] 2.26 2.33 Power Drift [dB] 0.04 0.01 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 80.6 Dist 3dB Peak [mm] 9.0 Warning(s) / Error(s) Details Area Scan Zoom Scan Warning(s) Error(s) . Measurement Report for Device, , , UID 0 -, Channel 0 (5250.000MHz) Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, N/A x N/A x N/A Dipole Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL , CW, 0-- 5250.000, 0 5.64 4.60 35.2 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - xxxx HBBL-600-10000 Charge:xxxx, 2024-Jun-12 EX3DV4 - SN7733, 2024-02-21 DAE4 Sn1739, 2024-01-23 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 40.0 x 80.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 10.0 x 10.0 4.0 x 4.0 x 1.4 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.4 MAIA N/A N/A Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-06-12, 13:01 2024-06-12, 13:11 psSAR1g [W/kg] 6.58 7.23 psSAR10g [W/kg] 1.85 2.15 Power Drift [dB] 0.09 0.12 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 64.6 Dist 3dB Peak [mm] 7.2 Warning(s) / Error(s) Details Area Scan Zoom Scan Warning(s) Error(s) Measurement Report for Device, , , UID 0 -, Channel 0 (5750.000MHz) Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, N/A x N/A x N/A Dipole Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL , CW, 0-- 5750.000, 0 5.05 5.23 36.2 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - xxxx HBBL-600-10000 Charge:xxxx, 2024-Jun-12 EX3DV4 - SN7733, 2024-02-21 DAE4 Sn1739, 2024-01-23 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 40.0 x 80.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 10.0 x 10.0 4.0 x 4.0 x 1.4 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.4 MAIA N/A N/A Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-06-12, 13:25 2024-06-12, 13:35 psSAR1g [W/kg] 6.99 7.92 psSAR10g [W/kg] 2.09 2.31 Power Drift [dB] 0.07 0.11 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 60.0 Dist 3dB Peak [mm] 7.6 Warning(s) / Error(s) Details Area Scan Zoom Scan Warning(s) Error(s)

. Measurement Report for Device, BACK, WLAN 2.4GHz, UID 10114 CAE, Channel 1 (2412.000MHz) Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, 200.0 x 200.0 x 30.0 Other Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL BACK, 0.00 WLAN 2.4GHz WLAN, 10114-CAE 2412.000, 1 7.98 1.81 42.1 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - xxxx HBBL-600-10000 Charge:xxxx, 2024-Jun-12 EX3DV4 - SN7733, 2024-02-21 DAE4 Sn1739, 2024-01-23 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 240.0 x 240.0 30.0 x 30.0 x 30.0 Grid Steps [mm] 10.0 x 10.0 5.0 x 5.0 x 1.5 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.5 MAIA Y N/A Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-06-12, 15:15 2024-06-12, 15:24 psSAR1g [W/kg] 0.152 0.156 psSAR10g [W/kg] 0.066 0.067 Power Drift [dB] -0.01 -0.01 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 78.1 Dist 3dB Peak [mm] 9.3 Warning(s) / Error(s) Details Area Scan Zoom Scan Warning(s) Error(s) . Measurement Report for Device, BACK, U-NII-1, UID 10062 CAE, Channel 36 (5180.000MHz) Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, 200.0 x 200.0 x 30.0 Other Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL BACK, 0.00 U-NII-1, U-NII-2A WLAN, 10062-CAE 5180.000, 36 5.64 4.54 35.4 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - xxxx HBBL-600-10000 Charge:xxxx, 2024-Jun-12 EX3DV4 - SN7733, 2024-02-21 DAE4 Sn1739, 2024-01-23 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 240.0 x 240.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 10.0 x 10.0 4.0 x 4.0 x 1.4 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.4 MAIA Y Y Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-06-12, 16:10 2024-06-12, 16:19 psSAR1g [W/kg] 0.209 0.219 psSAR10g [W/kg] 0.083 0.087 Power Drift [dB] -0.11 -0.08 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 67.5 Dist 3dB Peak [mm] 9.7 Warning(s) / Error(s) Details Area Scan Zoom Scan Warning(s) Error(s) . Measurement Report for Device, BACK, U-NII-3, UID 10062 CAE, Channel 165 (5825.000MHz) Device under Test Properties Model, Manufacturer Dimensions [mm] IMEI DUT Type Device, 200.0 x 200.0 x 30.0 Other Exposure Conditions Phantom Section, TSL Position, Test Distance [mm] Band Group, UID Frequency [MHz], Channel Number Conversion Factor TSL Conductivity [S/m] TSL Permittivity Flat, HSL BACK, 0.00 U-NII-2C, U-NII-3 WLAN, 10062-CAE 5825.000, 165 5.05 5.34 35.9 Hardware Setup Phantom TSL, Measured Date Probe, Calibration Date DAE, Calibration Date Twin-SAM V8.0 (30deg probe tilt) - xxxx HBBL-600-10000 Charge:xxxx, 2024-Jun-12 EX3DV4 - SN7733, 2024-02-21 DAE4 Sn1739, 2024-01-23 Scan Setup Area Scan Zoom Scan Grid Extents [mm] 240.0 x 240.0 22.0 x 22.0 x 22.0 Grid Steps [mm] 10.0 x 10.0 4.0 x 4.0 x 1.4 Sensor Surface [mm] 3.0 1.4 Graded Grid N/A Yes Grading Ratio N/A 1.4 MAIA Y Y Surface Detection VMS + 6p VMS + 6p Scan Method Measured Measured Measurement Results Area Scan Zoom Scan Date 2024-06-12, 16:36 2024-06-12, 16:44 psSAR1g [W/kg] 0.607 0.615 psSAR10g [W/kg] 0.231 0.226 Power Drift [dB] 0.04 0.15 Power Scaling Disabled Disabled Scaling Factor [dB] TSL Correction No correction No correction M2/M1 [%] 58.3 Dist 3dB Peak [mm] 10.8 Warning(s) / Error(s) Details Area Scan Zoom Scan Warning(s) Error(s)

R（Ω）X（jΩ）R（Ω）X（jΩ）R（Ω）X（jΩ） 56.400.96059.220.855 2.82-0.11 Annual Verification Result Measure Date -24.288-21.44-11.7% 16-Dec-22 Return loss(dB) Dipole2450 Head TSL Target ValueMeasure ValueDifference Impedance Annual Verification Result Dipole2450 Head TSL Target Value Measure Value Difference R （Ω） X （jΩ） R （Ω） X （jΩ） R （Ω） X （jΩ） Impedance 56.40 0.960 58.31 -0.127 1.91 -1.09 Return loss(dB) -24.288 -22.3 -8.2% Measure Date 16-Dec-23 Annual Verification Result Dipole5250 Head TSL Target Value Measure Value Difference R（Ω） X（jΩ） R （Ω） X （jΩ） R （Ω） X （jΩ） Impedance 48.99 -5.890 45.94 -5.120 -3.05 0.77 Return loss(dB) -24.399 -23.35 -4.3% Measure Date 14-Dec-22 Annual Verification Result Dipole5600 Head TSL Target Value Measure Value Difference R（Ω） X（jΩ） R （Ω） X （jΩ） R （Ω） X （jΩ） Impedance 50.56 -1.177 49.59 1.540 -0.97 2.72 Return loss(dB) -37.744 -35 -7.3% Measure Date 14-Dec-22 Annual Verification Result Dipole5750 Head TSL Target Value Measure Value Difference R（Ω） X（jΩ） R （Ω） X （jΩ） R （Ω） X （jΩ） Impedance 54.72 0.028 55.70 -1.100 0.98 -1.13 Return loss(dB) -26.929 -25.2 -6.4% Measure Date 14-Dec-22 Annual Verification Result Dipole5250 Head TSL Target Value Measure Value Difference R（Ω） X（jΩ） R（Ω） X（jΩ） R（Ω） X（jΩ） Impedance 48.99 -5.890 49.57 -4.560 0.58 1.33 Return loss(dB) -24.399 -26.75 9.6% Measure Date 14-Dec-23 Annual Verification Result Dipole5600 Head TSL Target Value Measure Value Difference R（Ω） X（jΩ） R（Ω） X（jΩ） R（Ω） X（jΩ） Impedance 50.56 -1.177 48.98 0.191 -1.58 1.37 Return loss(dB) -37.744 -39.56 4.8% Measure Date 14-Dec-23 Annual Verification Result Dipole5750 Head TSL Target Value Measure Value Difference R（Ω） X（jΩ） R（Ω） X（jΩ） R（Ω） X（jΩ） Impedance 54.72 0.028 55.22 -1.440 0.50 -1.47 Return loss(dB) -26.929 -25.78 -4.3% Measure Date 14-Dec-23

The results reported herein have been performed in accordance with the laboratory’s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. CFR 47 FCC PART 15 SUBPART C ISED RSS-247 Issue 3 TEST REPORT For INFINITY GAME BOARD MODEL NUMBER: IGB-I-301202 REPORT NUMBER: 4791327949.2-RF-1 ISSUE DATE: June 19, 2024 FCC ID: 2APXHIGB5G IC: 24128-IGB5G Prepared for WF Tastemakers Trading Limited FCC Address: Unit 05 and unit 06, 6th Floor, Greenfield Tower Concordia Plaza, 1 Science Museum Road, TST East, Hong Kong ISED Address: 347 Fifth Avenue Suite 1402-199, New York NY 10018 United States Of America (Excluding The States Of Alaska) Prepared by UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch Building 10, Innovation Technology Park, No. 1, Li Bin Road, Song Shan Lake Hi- Tech Development Zone Dongguan, 523808, People’s Republic of China Tel: +86 769 22038881 Fax: +86 769 33244054 Website: www.ul.com REPORT NO.: 4791327949.2-RF-1 Page 2 of 106 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Revision History Rev. Issue Date Revisions Revised By V0 June 19, 2024 Initial Issue REPORT NO.: 4791327949.2-RF-1 Page 3 of 106 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. Summary of Test Results Test Item Clause Limit/Requirement Result Antenna Requirement N/A FCC Part 15.203/15.247 (c) RSS-GEN Clause 6.8 Pass AC Power Line Conducted Emission ANSI C63.10-2013, Clause 6.2 FCC Part 15.207 RSS-GEN Clause 8.8 Pass Conducted Output Power ANSI C63.10-2013, Clause 11.9.2.3.1 FCC Part 15.247 (b)(3) RSS-247 Clause 5.4 (d) Pass 6dB Bandwidth and 99% Occupied Bandwidth ANSI C63.10-2013, Clause 11.8.1 FCC Part 15.247 (a)(2) RSS-247 Clause 5.2 (a) ISED RSS-Gen Clause 6.7 Pass Power Spectral Density ANSI C63.10-2013, Clause 11.10.5 FCC Part 15.247 (e) RSS-247 Clause 5.2 (b) Pass Conducted Band edge and spurious emission ANSI C63.10-2013, Clause 11.11 FCC Part 15.247(d) RSS-247 Clause 5.5 Pass Radiated Band edge and Spurious Emission ANSI C63.10-2013, Clause 11.12 & Clause 11.13 FCC Part 15.247 (d) FCC Part 15.205/15.209 RSS-247 Clause 5.5 RSS-GEN Clause 8.9 Pass Duty Cycle ANSI C63.10-2013, Clause 11.6 None; for reporting purposes only. Pass *This test report is only published to and used by the applicant, and it is not for evidence purpose in China. *The measurement result for the sample received is <Pass> according to <CFR 47 FCC PART 15 SUBPART C，ISED RSS-247 Issue 3> when <Simple Acceptance> decision rule is applied. REPORT NO.: 4791327949.2-RF-1 Page 4 of 106 UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch FORM NO: 10-SL-F0035 This report shall not be reproduced except in full, without the written approval of UL Verification Services (Guangzhou) Co., Ltd, Song Shan Lake Branch. CONTENTS 1. ATTESTATION OF TEST RESULTS ..................................................................................... 6 2. TEST METHODOLOGY ......................................................................................................... 8 3. FACILITIES AND ACCREDITATION ..................................................................................... 8 4. CALIBRATION AND UNCERTAINTY ................................................................................... 9 4.1. MEASURING INSTRUMENT CALIBRATION ........................................................... 9 4.2. MEASUREMENT UNCERTAINTY ............................................................................ 9 5. EQUIPMENT UNDER TEST ................................................................................................ 10 5.1. DESCRIPTION OF EUT ......................................................................................... 10 5.2. CHANNEL LIST ...................................................................................................... 10 5.3. MAXIMUM POWER ................................................................................................ 10 5.4. TEST CHANNEL CONFIGURATION ...................................................................... 10 5.5. THE WORSE CASE POWER SETTING PARAMETER .......................................... 11 5.6. DESCRIPTION OF AVAILABLE ANTENNAS ......................................................... 12 5.7. SUPPORT UNITS FOR SYSTEM TEST ................................................................. 13 6. MEASURING EQUIPMENT AND SOFTWARE USED......................................................... 14 7. ANTENNA PORT TEST RESULTS ..................................................................................... 17 7.1. CONDUCTED OUTPUT POWER ........................................................................... 17 7.2. 6DB BANDWIDTH AND 99% OCCUPIED BANDWIDTH ........................................ 18 7.3. POWER SPECTRAL DENSITY .............................................................................. 20 7.4. CONDUCTED BAND EDGE AND SPURIOUS EMISSION ..................................... 22 7.5. DUTY CYCLE ......................................................................................................... 24 8. RADIATED TEST RESULTS ............................................................................................... 25 8.1. RESTRICTED BANDEDGE .................................................................................... 33 8.2. SPURIOUS EMISSIONS(1 GHZ~3 GHZ) ............…

Text truncated - open the document above for the full version.

1/12 深圳市联航数码科技有限公司 United Digital Technology Co., Limited IGB18-WiFi Antenna Specification 客户： CUSTOMER ： 客 户 案 号： *CUSTOMER P/N ： 本 厂 编 号： OUR MODELNO ： 品 名 / 规 格： SPECIFICATIONS ： IGB185-2458-WiFiantenna 样 品 数： QTY ： 日期： Date:2024-05-08 ShenzhenYuchen Technology Co. , Ltd Customer客户承认 射频 RF 结构 Structural 核准 Approved 签名（盖章） Wand JiaxiZhou Lei Dai Wenzheng Address: 11th Floor, Mingteng Center Building, Qinghu Road, Qinghua Community, Longhua Street, Longhua District, Shenzhen 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 2/12 目录 一.封面(Cover）......................................................1 二.目录（Index）......................................................2 三.基本参数（Thebasicparameters）...........................3 四.工程图纸（ProductDrawing）..............................4 五.测试设备（TheEquipment&Conditions）..................4 六.性能测试报告（TheReport）.................................7 七.环境测试（environmentaltesting）...........................9 八.安装方式（installationmethod）..............................10 九.包装（packaging）................................................11 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 3/12 三基本参数Thebasicparameters 主要技术指标Maintechnicalspecifications 频率范围 （MHz） 2400-2500 5150-5850 FrequencyRange (MHz) 2400-2500 5150-5850 特性阻抗(Ω)50Impedance(Ω)50 峰值增益(dBi)＞4PeakGain(dBi)＞4 电压驻波比≤2.5VSWR≤2.5 最大功率10WAdmittedPower10W 极化方式 线极化 Polarization Linear polarization 连接方式IPEX-1ConnectorTypeIPEX-1 物理性能PhysicalProperties 天线本体材料FPCAntennaBaseFPC 颜色黑色ColourBlack 天线尺寸30.5*43.2mm Antenna Dimensions 30.5*43.2mm 连接线长度200mm Connectingline length 200mm 工作温度-20°C~+85°COperatingTemp-20°C~+85°C 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 4/12 四工程图纸ProductDrawing 五测试设备TheEquipment&Conditions 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 5/12 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 6/12 EquipmentManufacturerModelNo.LastCal.DueDate Communication comprehensive tester R&SCMW5002023.11.042024.11.03 NetworkanalyzerAgilent5071C2023.11.042024.11.03 NetworkanalyzerR&SZVB82023.11.042024.11.03 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 7/12 六性能测试报告（TheReport） 6.1驻波（SWR） Frequency2400MHz2450MHz2500MHz5150MHz5500MHz5850MHz EquipmentManufacturerModelNo.Factory number Softwareversion Communication comprehensivetester R&SCMW500135128WLAN:3.5.40 NetworkanalyzerAgilent5071C1192117A.11.31 NetworkanalyzerR&SZVB81010872.71 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 8/12 SWR1.421.581.781.871.581.43 6.2无源增益、效率(Passivegain,efficiency) FrequencyID123456789101112 Frequency(MHz)240024202440245024602480250051505350550056505850 Efficiency(dBi)-1.55-1.81-1.80-1.63-1.68-1.47-1.76-1.93-1.59-2.00-1.84-1.40 Gain(dBi)1.451.651.651.661.661.681.61.851.821.751.941.95 Efficiency(%)69.9265.9266.1368.7067.9371.3566.6164.0869.4163.1365.4472.48 6.3辐射方向图(Radiationpattern) 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 9/12 6.4 有源测试数据（ ActiveTestData ） 802.11bch1ch6ch11802.11gch1ch6ch11 TRP-11M12.5613.1113.51TRP-6M12.3412.1712.16 TIS-11M-82.47-82.25-82.35TIS-54M-70.41-70.36-70.22 802.11nch1ch6ch11802.11ach149Ch157Ch165 TRP-MCS012.3712.5612.18TRP-54M10.0210.3310.58 TIS-MCS7-67.72-67.12-67.57TIS-54M-69.06-69.48-69.68 七、环境可靠性试验报告 environmentaltesting 1 、可靠性测试报告Reliadilitytestreport 测试项目测试方法要求结果 C1 V.S.W.R.电性驻波比网路分析仪参数进行测试符合待测物规范 pass M1天线增益天线暗室参数进行测试符合待测物规范pass M2Vibration震动 GB/T2423.48-2008 Amplitude:0.03inch(1.5mm);Freq:20to 80to20Hz3directions;2hoursforeach direction振幅1.5mm；频率20~80~20Hz；3 个方向各2H 1.NoVisualDamage 2.FrequencyTol.≤5% 无明显外观不良;频率偏 移≤5% pass 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 10/12 M6RandomDrop跌落 GB/T2423.8-1995Single：Height:1.0 Meter;3directions;1timeforeach direction单支天线，高1m；3个方向各1次 1.Nopartsseparated、 fracture 2.FrequencyTol.≤5% 产品无脱落、断裂;频率偏 移≤5% pass E3Dimension尺寸 Inspectionofdimension,color,material, package,surfaceprocess.检查尺寸,颜色,材 料,包装,表面处理 DirectiveDUT specification 符合待测物规范 pass M1RoHS WithReferencetoIEC62321:2008withflow chart 参考IEC62321测试流程 DirectiveRoHS 2015/863/EU 符合RoHS 2015/863/EU标准 pass 八安装方式（installationmethod） 1、将天线贴在支撑棉上。（Attachtheantennatothesupportcotton.） 2、参考样机，将支撑棉和天线贴在指定位置。（Refertotheprototype,stickthesupportcottonandthe antennainthedesignatedposition.） 深圳市联航数码科技有限公司 UnitedDigitalTechnologyCo.,Limited 11/12 3、天线外露焊盘处贴上导电布。（Affixaconductiveclothtotheexposedpadoftheantenna.） 4、在同轴电缆中剥位置对应的金属板位置贴上导电海绵。（Aconductivespongeispastedonthemetal platecorrespondingtothestrippingpositioninthecoaxialcable.） 5、将同轴电缆中剥位置放置在导电海绵居中位置，然后贴上导电布并压实导电布，让同轴电缆中剥部分 与金属板充分接触。（Placethestrippingpositionofthecoaxialcableinthecenterofthe conductivesponge,andthenpastetheconductiveclothandcompacttheconductivecloth,so thatthestrippingpartofthecoaxialcableisinfullcontactwiththemetalplate.） 九包装（ packaging ） 一、装箱要求(Thepackingrequirements) 作业说明(jobdescription)： 1.内包装(innerpacking；insidepacking；make-up)： 产品100PCS/小袋(Product100PCS/pouch) 2.外包装(externalpackin…

Text truncated - open the document above for the full version.