2AQ6V-KINSOUNDBARSoundbar

OWNERS MANUAL Totemacoustic.com 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one wider than the other. The wide bladed is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. The equipment shall be used at maximum 35 degree C ambient temperature. 14. Do not open the equipment to reduce the risk of electrical shock. For safety reasons it is only allowed to be opened by qualified service personnel. 15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. And the apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. 16. The MAINS plug or appliance inlet is used as the disconnect device and shall remain readily operable. 17. The product shall be used on open bench. 18. No naked flame sources, such as lighted candles, should be placed on the apparatus. 19. The use of apparatus in tropical climates. - 20. Minimum 10cm distances around the apparatus for sufficient ventilation 21. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. 22. WARNING Do not ingest the battery, Chemical burn hazard (The remote control supplied with) This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. 23. Warning: the apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. Totemacoustic.com FCC Warnings This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC WARNING This radio transmitter has been approved by Industry Canada. This Class B digital apparatus complies with Canadian standard ICES-003. This device complies with Industry Canada License exempt RSS standard(s). Operation is subject to the following two conditions. This device may not cause interference and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industrie Canada (IC) Le present appareil est conforme aux CNR d'Industrie Canada applicablesaux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.AVIS RELATIFS A L'EXPOSITION RF Cet equipement est conforme aux limites d'exposition au rayonnement ISED etablies pour un environnement non controle. Cet equipement doit etre installe et utilise a une distance minimale de 20 cm entre le radiateur et votre corps. CAUTION To prevent electrical shock do not use the electrical plug of your Totem Subwoofer with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent exposure. To protect against the risk of electrical shock do not use near bathtubs, sinks, swimming pools, saunas, in wet basements, near other water sources, or rain. If service is required, please refer to your Totem Authorized Dealer. Totemacoustic.com Discover yours. We sincerely thank you for …

Text truncated - open the document above for the full version.

Totemacoustic.com MANUEL D'UTILISATION Totemacoustic.com 1. Lisez ces instructions. 2. Conservez ces instructions. 3. Observez tous les avertissements. 4. Suivez toutes les instructions. 5. N'utilisez pas cet appareil à proximité de l'eau. 6. Utilisez uniquement un chiffon sec pour le nettoyer. 7. Ne bloquez pas les ouvertures de ventilation. Installez conformément aux instructions du fabricant. 8. Ne l'installez pas à proximité de sources de chaleur telles que des radiateurs, des bouches de chaleur, des poêles ou d'autres appareils (amplificateurs compris) produisant de la chaleur. 9. Ne pas contourner le dispositif de sécurité de la fiche polarisée. Une fiche polarisée possède deux lames dont une plus large que l'autre. La grande lame est fournie pour votre sécurité. Si la fiche fournie ne rentre pas dans votre prise, consultez un électricien pour le remplacement de la prise obsolète. 10. Protégez le cordon d'alimentation, surtout au niveau des fiches, des prises et des points où il sort de l'appareil, pour éviter qu'on ne marche dessus ou qu'on ne le pince. 11. Utilisez uniquement les accessoires spécifiés par le fabricant. 12. Débranchez cet appareil lors d'orage avec foudre ou lorsque vous ne l'utilisez pas pendant des périodes prolongées. 13. Faites-le réparer et entretenir par un personnel de service qualifié. Il est nécessaire de faire réparer l'appareil lorsqu'il a subi des dommages quelconques du type suivant : cordon ou fiche d'alimentation abîmé, liquide renversé ou objets tombés dans l'appareil, exposition de l'appareil à la pluie ou à l'humidité, mauvais fonctionnement ou chute. 14. La température ambiante lors de l'utilisation ne doit pas dépasser 45 degrés Celsius. 15. Afin de réduire les risques d'électrocution, n'ouvrez pas l'équipement. Pour des raisons de sécurité, seul du personnel d'entretien qualifié est autorisé à l'ouvrir. 16. ATTENTION: Pour réduire le risque d'incendie ou d'électrocution, n'exposez pas cet appareil à la pluie ou à l'humidité. De plus, l'appareil ne doit pas être exposé au dégouttement ou aux éclaboussures et aucun objet rempli de liquide, tel qu'un vase, ne doit être posé sur l'appareil. 17. La fiche d'alimentation CA sert de principal dispositif de déconnexion et doit toujours être capable de fonctionner correctement. 18. Ce produit doit être utilisé sur une surface ouverte 19. Aucune source de flame nue, telle, que des bougies allumées, ne doit être placé sur l'appareil. 20. L'utilisation d'appareils dans les climats tropicaux et / ou modérés. 21. Distances minimales 10cm autour de l'appareil pour une ventilation adéquate; 22. La ventilation ne doit pas être gênée en couvrant les ouvertures de ventilation avec des articles tels que des journaux, des nappes, des rideaux, etc. 23. Attention: l'appareil de construction de classe I doit être raccordé à une prise secteur avec une mise à la terre de protection. IMPORTANTES MESURES DE SÉCURITÉ Totemacoustic.com Avertissements de la FCC Cet appareil est conforme à la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences nuisibles, et (2) cet appareil doit accepter toutes les interférences reçues, y compris celles qui peuvent provoquer un fonctionnement indésirable. Tout changement ou modification non expressément approuvé par la partie responsable de la conformité pourrait annuler l'autorité de l'utilisateur à faire fonctionner l'équipement. Remarque : Cet équipement a été testé et jugé conforme aux limites applicables aux appareils numériques de classe B, conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère des utilisations et peut émettre de l'énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément aux instructions, il peut causer des interférences nuisibles aux communications radio. Cependant, il n'y a aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet équipement cause des interférences nuisibles à la réception de la radio ou de la télévision, ce qui peut être déterminé en éteignant et en allumant l'équipement, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes : - Réorientez ou déplacez l'antenne de réception. - Augmentez la séparation entre l'équipement et le récepteur. - Branchez l'équipement sur une prise d'un circuit différent de celui auquel le récepteur est connecté. - Consultez le revendeur ou un technicien radio/TV expérimenté pour obtenir de l'aide. Cet équipement est conforme aux limites d'exposition aux radiations de la FCC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec distance minimale de 20 cm entre le radiateur et votre corps. IC AVERTISSEMENT Cet émetteur radio a été approuvé par Industrie Canada. Cet appareil numérique de classe B est conforme à la norme canadienne ICES-003. Cet appareil est conforme à la (aux) norme(s) RSS exempte(s) de licence d'Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes. Cet appareil ne doit pas causer d'interférences et (2) cet appareil doit accepter toute interférence, y compris celles qui peuvent provoquer un fonctionnement non souhaité de l'appareil. Cet appareil est conforme aux limites d'exposition aux radiations ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec distance minimale de 20 cm entre le radiateur et votre corps. Industrie Canada (IC) Le present appareil est conforme aux CNR d'Industrie Canada applicablesaux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme s…

Text truncated - open the document above for the full version.

TOTEM ACOUSTIQUE INC. for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 <2020-06-08> TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AQ6V-KINSOUNDBAR KIN Play Sound Bar For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, ------------------------------------ Name: Vince Bruzzese/President Company: TOTEM ACOUSTIQUE INC. Address: 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Phone: 514-259-1062 Fax: 514-259-4968 E-Mail: [email protected]

TOTEM ACOUSTIQUE INC. 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Tel: 514-259-1062 Fax: 514-259-4968 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2020/06/08 To whom it may concern: We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relati ng to applications for equipment authorization FCC ID: [2AQ6V-KINSOUNDBAR] including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name: Vince Bruzzese/President Company: TOTEM ACOUSTIQUE INC. Address: 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Phone: 514-259-1062 Fax: 514-259-4968 E-Mail: [email protected]

IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR

Label and label location

IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR 5.8G ANT BT ANT IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR FCC ID: 2AQ6V-KINSOUNDBAR

RF Exposure evaluation Exposure category: General population/uncontrolled environment EUT Type: Production Unit Device Type: Mobile Device Refer Standard: KDB 447498 D01 General RF Exposure Guidance v06 FCC Part 2 §2.1091 FCC ID: 2AQ6V-KINSOUNDBAR 1. Reference According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. KDB447498 D01: Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies 2. Limit Limits for Maximum Permissible Exposure (MPE)/Controlled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 6 3.0 – 30 1842/f 4.89/f (900/f 2 )* 6 30 – 300 61.4 0.163 1.0 6 300 – 1500 / / f/300 6 1500 – 100,000 / / 5 6 Limits for Maximum Permissible Exposure (MPE)/Uncontrolled Exposure Frequency Range(MHz) Electric Field Strength(V/m) Magnetic Field Strength(A/m) Power Density (mW/cm²) Averaging Time (minute) Limits for Occupational/Controlled Exposure 0.3 – 3.0 614 1.63 (100) * 30 3.0 – 30 824/f 2.19/f (180/f 2 )* 30 30 – 300 27.5 0.073 0.2 30 300 – 1500 / / f/1500 30 1500 – 100,000 / / 1.0 30 F=frequency in MHz *=Plane-wave equivalent power density 3. MPE Calculation Method Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S=PG/4πR² Where: S=power density P=power input to antenna G=power gain of the antenna in the direction of interest relative to an isotropic radiator R=distance to the center of radiation of the antenna 4. Result As declared by the Applicant, the EUT is a wireless device used in a fix application, at least 20 cm from any body part of the user or nearby persons; from the maximum EUT RF output power, the minimum separation distance, r =20cm, as well as the gain of the used BT antenna is 0.11 dBi and 5.8G antenna is 2dBi, the RF power density can be obtained. EDR Freq. (MHz) Output Power (dBm) Target power W/ tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result GFSK 2402 4.241 4±1.0 5 3.162 0.11 0.00065 1 Pass 2441 4.154 4±1.0 5 3.162 0.11 0.00065 1 Pass 2480 3.998 4±1.0 5 3.162 0.11 0.00065 1 Pass π/4DQPSK 2402 3.891 4±1.0 5 3.162 0.11 0.00065 1 Pass 2441 3.694 4±1.0 5 3.162 0.11 0.00065 1 Pass 2480 3.542 4±1.0 5 3.162 0.11 0.00065 1 Pass 8DPSK 2402 3.456 4±1.0 5 3.162 0.11 0.00065 1 Pass 2441 3.698 4±1.0 5 3.162 0.11 0.00065 1 Pass 2480 3.588 4±1.0 5 3.162 0.11 0.00065 1 Pass BLE Freq. (MHz) Output Power (dBm) Target power W/ tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result GFSK 2402 3.588 4±1.0 5 3.162 0.11 0.00065 1 Pass 2440 3.654 4±1.0 5 3.162 0.11 0.00065 1 Pass 2480 3.725 4±1.0 5 3.162 0.11 0.00065 1 Pass 5.8G Freq. (MHz) Output Power (dBm) Target power W/ tolerance (dBm) Max tune up power tolerance (dBm) Output power to antenna (mW) Ant Gain (dBi) Power Density at R=20cm (mW/cm2) Limit (mW/c m2) Result GFSK 5727 10.25 10±1.0 11 12.589 2 0.00397 1 Pass 5771 10.51 10±1.0 11 12.589 2 0.00397 1 Pass 5804 10.35 10±1.0 11 12.589 2 0.00397 1 Pass Note: The estimation distance is 20cm Summary simultaneous transmission results MPE Ratio BT MPE Ratio 5.8G ∑MPE ratios Limit Results 0.00065 0.00397 0.0046 1.0 PASS 5. Conclusion The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device.

Page 1 of 35 Report No.: UNIA20060114FR-02 FCC RADIO TEST REPORT FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR Product： Soundbar Trade Name： Totem Model Name： KIN Play Sound Bar Serial Model： N/A Report No.： UNIA20060114FR-02 Prepared for TOTEM ACOUSTIQUE INC. 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China Page 2 of 35 Report No.: UNIA20060114FR-02 TEST RESULT CERTIFICATION Applicant’s name ................. : TOTEM ACOUSTIQUE INC. Address ................................. : 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Manufacture's Name ............ : TOTEM ACOUSTIQUE INC. Address ................................. : 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Product description Product name ............................ : Soundbar Trade Mark ............................ : To t e m Model and/or type reference : KIN Play Sound Bar Standards ............................. : FCC Rules and Regulations Part 15 Subpart C Section 15.247, RSS-247 Issue 2: February 2017, RSS-Gen Issue 5 April 2018 ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test ........................................... : Date (s) of performance of tests ............. : May 4 ~ Jun. 8, 2020 Date of Issue .......................................... : Jun. 9, 2020 Test Result.............................................. : Pass Tested by: Kahn yang/Engineer Reviewer: Sherwin Qian/Supervisor Approved & Authorized Signer: Liuze/Manager Page 3 of 35 Report No.: UNIA20060114FR-02 Table of Contents Page 1. TEST SUMMARY ....................................................................................................... 5 1.1 TEST PROCEDURES AND RESULTS ........................................................................ 5 1.2 TEST FACILITY ........................................................................................................... 5 1.3 MEASUREMENT UNCERTAINTY ............................................................................... 5 2. GENERAL INFORMATION ........................................................................................ 6 2.1 GENERAL DESCRIPTION OF EUT ............................................................................ 6 2.2 Carrier Frequency of Channels .................................................................................... 7 2.3 Operation of EUT during testing .................................................................................. 7 2.4 DESCRIPTION OF TEST SETUP ............................................................................... 7 2.5 MEASUREMENT INSTRUMENTS LIST...................................................................... 8 3. CONDUCTED EMISSIONS TEST ............................................................................. 9 3.1 Conducted Power Line Emission Limit .......................................................................... 9 3.2 Test Setup ..................................................................................................................... 9 3.3 Test Procedure .............................................................................................................. 9 3.4 Te s t Result .................................................................................................................... 9 4. RADIATED EMISSION TEST ................................................................................... 12 4.1 Radiation Limit ............................................................................................................ 12 4.2 Test Setup ................................................................................................................... 12 4.3 Test Procedure ............................................................................................................ 13 4.4 Test Result .................................................................................................................. 13 5. BAND EDGE ............................................................................................................ 18 5.1 Limits .......................................................................................................................... 18 5.2 Test Procedure ............................................................................................................ 18 5.3 Test Result .................................................................................................................. 18 6. OCCUPIED BANDWIDTH MEASUREMENT ........................................................... 19 6.1 Test Limit ..................................................................................................................... 19 6.2 Test Procedure ............................................................................................................ 19 6.3 Measurement Equipment Used ................................................................................... 19 6.4 Test Result .................................................................................................................. 19 7. POWER SPECTRAL DENSITY TEST ..................................................................... 23 7.1 Test Limit ..................................................................................................................... 23 7.2…

Text truncated - open the document above for the full version.

Page 1 of 34 Report No.: UNIA20060114FR-03 FCC RADIO TEST REPORT FCC ID: 2AQ6V-KINSOUNDBAR IC: 24314-KINSOUNDBAR Product： Soundbar Trade Name： Totem Model Name： KIN Play Sound Bar Serial Model： N/A Report No.： UNIA20060114FR-03 Prepared for TOTEM ACOUSTIQUE INC. 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China Page 2 of 34 Report No.: UNIA20060114FR-03 TEST RESULT CERTIFICATION Applicant’s name ................. : TOTEM ACOUSTIQUE INC. Address ................................. : 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Manufacture's Name ............ : TOTEM ACOUSTIQUE INC. Address ................................. : 9165, Champ d’Eau, St. Leonard, Quebec, H1P3M3, Canada Product description Product name ............................ : Soundbar Trade Mark ............................ : To t e m Model and/or type reference : KIN Play Sound Bar Standards ............................. : FCC Rules and Regulations Part 15 Subpart C Section 15.247, RSS-247 Issue 2: February 2017, RSS-Gen Issue 5 April 2018 ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test ........................................... : Date (s) of performance of tests ............. : May 4 ~ Jun. 8, 2020 Date of Issue .......................................... : Jun. 9, 2020 Test Result.............................................. : Pass Tested by: Kahn yang/Engineer Reviewer: Sherwin Qian/Supervisor Approved & Authorized Signer: Liuze/Manager Page 3 of 34 Report No.: UNIA20060114FR-03 Table of Contents Page 1. TEST SUMMARY ....................................................................................................... 5 1.1 TEST PROCEDURES AND RESULTS ........................................................................ 5 1.2 TEST FACILITY ........................................................................................................... 5 1.3 MEASUREMENT UNCERTAINTY ............................................................................... 5 2. GENERAL INFORMATION ........................................................................................ 6 2.1 GENERAL DESCRIPTION OF EUT ............................................................................ 6 2.2 Carrier Frequency of Channels .................................................................................... 6 2.3 Operation of EUT during testing .................................................................................. 6 2.4 DESCRIPTION OF TEST SETUP ............................................................................... 6 2.5 MEASUREMENT INSTRUMENTS LIST...................................................................... 7 3. CONDUCTED EMISSIONS TEST ............................................................................. 8 3.1 Conducted Power Line Emission Limit .......................................................................... 8 3.2 Test Setup ..................................................................................................................... 8 3.3 Test Procedure .............................................................................................................. 8 3.4 Te s t Result .................................................................................................................... 8 4. RADIATED EMISSION TEST ................................................................................... 11 4.1 Radiation Limit ............................................................................................................ 11 4.2 Test Setup ................................................................................................................... 11 4.3 Test Procedure ............................................................................................................ 12 4.4 Test Result .................................................................................................................. 12 5. BAND EDGE ............................................................................................................ 17 5.1 Limits .......................................................................................................................... 17 5.2 Test Procedure ............................................................................................................ 17 5.3 Test Result .................................................................................................................. 17 6. OCCUPIED BANDWIDTH MEASUREMENT ........................................................... 18 6.1 Test Limit ...........…

Text truncated - open the document above for the full version.