2AQM6SYNCself-balance scooter

Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interf e rence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit diff e rent from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interf e rence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the usefs authority to operate this equipment. IMPORTANT NOTES Co-location warning: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCCID:2AQM6SYNC

LabelLocationOnEUT Label ProductName:self-balancescooter ModelNo.:EL-ES28 FCCID:2AQM6SYNC ThisdevicecomplieswithPart15oftheFCCRules. Operationissubjecttothefollowingtwoconditions: (1)Thisdevicemaynotcauseharmfulinterference,and (2)Thisdevicemustacceptanyinterferencereceived, includinginterferencethatmaycauseundesired operation.

FCCID:2AQM6SYNC ANT

version01 JetsonElectricBikesLLC DeclarationconcerningAntennaSpecification Itisherebydeclaredthattheproduct ModelNo.: EL-ES28,JSYNC-BLK,JSYNC-VIO,JSYNC-TEL,JSYNC-BLU,SYNC，JSYNC-GRN, JSYNC-ELC,JSYNC-RED FCCID:2AQM6SYNC fulfillstherequirementinFCCtestrelatingtotheantennatype. ThedevicespecifiedaboveconfirmstotheFCCrecommendationsforinternalantennatype(s) describedbelow: ModelNo.ofantenna:N/A Typeofantenna: PCBAntenna Gainoftheantenna: -0 dBi Frequencyrange: 2402-2480MHz Themountingoftheantennaisfixedtotheradiomoduleandnootherantennashouldbeused. Sincerely, MichaelStrange DirectorOfProductDevelopment CompanyName:JetsonElectricBikesLLC CompanyAddress:1ReweStreetBrooklynNY11211UnitedStates

RFEXPOSUREEVALUATION FCCID:2AQM6SYNC AccordingtoFCC1.1310:Thecriterialistedinthefollowingtableshallbeused toevaluatetheenvironmentimpactofhumanexposuretoradiofrequency(RF) Radiationasspecifiedin§1.1307(b): RoutineSARevaluationreferstothatspecificallyrequiredby§2.1093,using measurementsorcomputersimulation.WhenroutineSARevaluationisnot required,portabletransmitterswithoutputpowergreaterthantheapplicable lowthresholdrequireSARevaluationtoqualifyforTCBapproval. Channel (MHz) Maximum output power (dBm) Tuneup tolerance (dBm) MaxTuneUp Power(dBm) Distance (mm) Calculation results Limit Operating Mode 2402 2.1932.193 ±1 3.19350.6473 BDR 2441 2.4832.483 ±1 3.48350.6973 2480 1.7471.747 ±1 2.74750.5933 2402 2.7492.749 ±1 3.74950.7353 EDR 2441 3.0243.024 ±1 4.02450.7893 2480 2.2462.246 ±1 3.24650.6653 TestResults:PASS.

Report No.: 18220WC100917 FCC ID: 2AQM6SYNC Page 1 of 61 Code:AB-RF-05-a FCC TEST REPORT Client Name : Jetson Electric Bikes LLC Address : 1 Rewe Street Brooklyn NY 11211 United States Product Name : self-balance scooter Date : May 21, 2021 Shenzhen Anbotek Compliance Laboratory Limited Report No.: 18220WC100917 FCC ID: 2AQM6SYNC Page 2 of 61 Code:AB-RF-05-a Contents 1. General Information ............................................................................................................................................ 5 1.1. Client Information ..................................................................................................................................... 5 1.2. Description of Device (EUT) ................................................................................................................... 5 1.3. Auxiliary Equipment Used During Test ................................................................................................. 6 1.4. Description of Test Modes ...................................................................................................................... 6 1.5. List of channels ........................................................................................................................................ 7 1.6. Description Of Test Setup ....................................................................................................................... 8 1.7. Test Equipment List ................................................................................................................................. 9 1.8. Measurement Uncertainty .................................................................................................................... 10 1.9. Description of Test Facility .................................................................................................................... 10 2. Summary of Test Results ................................................................................................................................. 11 3. Conducted Emission Test ................................................................................................................................ 12 3.1. Test Standard and Limit ........................................................................................................................ 12 3.2. Test Setup ............................................................................................................................................... 12 3.3. Test Procedure ....................................................................................................................................... 12 3.4. Test Data ................................................................................................................................................. 12 4. Radiation Spurious Emission and Band Edge .............................................................................................. 17 4.1. Test Standard and Limit ........................................................................................................................ 17 4.2. Test Setup ............................................................................................................................................... 17 4.3. Test Procedure ....................................................................................................................................... 18 4.4. Test Data ................................................................................................................................................. 19 5. Maximum Peak Output Power Test ................................................................................................................ 27 5.1. Test Standard and Limit ........................................................................................................................ 27 5.2. Test Setup ............................................................................................................................................... 27 5.3. Test Procedure ....................................................................................................................................... 27 5.4. Test Data ................................................................................................................................................. 27 6. 20DB Occupy Bandwidth Test ......................................................................................................................... 31 6.1. Test Standard ......................................................................................................................................... 31 6.2. Test Setup ............................................................................................................................................... 31 6.3. Test Procedure ....................................................................................................................................... 31 6.4. Test Data ................................................................................................................................................. 31 7. Carrier Frequency Separation Test................................................................................................................. 35 7.1. Test Standard and Limit ........................................................................................................................ 35 7.2. Test Setup ............................................................................................................................................... 35 7.3. Test Procedure ....................................................................................................................................... 35 7.4. Test Data ................................................................................................................…

Text truncated - open the document above for the full version.

FCCID:2AQM6SYNC PhotoofConductedEmissionTest PhotoofRadiationEmissionTest