2AQX5KD-C70Two Way Radio

Scanning： It is convenient for the user to search for calls from other channels.When“Side Key 2” in the software is programmed to the scanning function,long press key for two seconds to enter into the scanning mode,the transceiver will start to scan with the current channel;Operate it again to exit. Chinese/English Voice Prompt： The transceiver has a manual switching function between the Chinese and the English.Switch to Channel 16,turn off the transceiver,then press both the power key and key and meanwhile turn on the transceiver to switch between the Chinese and English. Time Out Timer(TOT)： The purpose of the TOT is to prevent any single person from using a channel for an extended period of time.An alarm will sound if the transmission continues beyond the set time.The transceiver will stop transmission if this occurs.To stop the alarm,release the PTT key and the transceiver will return to standby. Busy Channel Lockout： The function can prevent interference from other transceivers using the same channel. High-Low Power： The transceiver has a high-low power selection,it can be programmed. Keyboard Lockout： Long press key to lock all buttons,operate it again to unlock. Power Display： Short press power key to display the current battery level. Monitoring： Long press key for two seconds to enter into the monitor mode,release it to exit. VOX： This function can be voice activated so the user doesn’t have to press the PTT key. When “VOX level” in the software is selected,short press key twice to enter into the VOX mode,then short press key or key to turn on/off the VOX. Frequency Range Supply Power Antenna Configuration Work Mode Ground Method Output Power Modulation Mode Sparious Radiation Preemphasis Ch aracter Emission Current Sensitivity Audio Power Audio Distortion Intermodulation Interference Resistance Receiving Current Standby Current 462.5500-462.7250MHz 467.5625-467.7125MHz DC3.7V Spring Antenna Co/Differ-frequency Simplex Communication Cathode 30.16dBm FM(F3E） ≤7.5μW Per Octave 6dB ≤1000mA ＜0.16μV（12dB SINAD） ≥300mW ＜5% ≥60dB ≤300mA ≤20mA Technical Parameters SPECIFICATIONS TRANSMITTER RECEIVER UHF Super Receiving Screen Display Scanning Monitoring VOX TOT Chinese/English Voice Prompt Keyboard Lockout Power Display Busy Channel Lockout High-Low Power Selection Power Saving Mode Low Battery Warning Voice Companding/Scrambling Function Programming Encryption Function Special Signaling 50 CTCSS/208 DCS Antenna Display Screen PTT Speaker Function Keys Charging the Battery PackIcons 1.The battery is not charged in the factory,please charge the battery under the environmental temperature 5—40°C before using. 2.After purchasing or long-term storage(more than two months), charging the battery for the first time can not reach its saturation capacity,repeat charge/discharge for twice or three times to make battery capacity achieve the best state. 3.Before charging,please power off the transceiver,using the transceiver during charging may affect correct charging. 4.If the battery has been charged fully,please do not charge it again,otherwise the service life of the battery may be shorten or may be damaged. 5.If the service time is significantly reduced even after compl etely correct charging,the battery can not be used any more,please replace a new battery. Power Key 1.Short press keys to adjust the volume. 2.Short press key to switch to channel mode,then short press keys to adjust the channels. 3.PTT: press this button whenever you wish to talk with the user of the other radio. MENU OPERATION low power channel high power channelvolume scanningchannel lockoutunlocking earphoneearphone volumetransmitting receivingalarmbattery level Belt Clip PTT Earphone USB Charging Port Desktop Charger Connector Desktop Charger Connector Be Familiar With The Machine Functions OperationFunctions Operation Battery Power Saving： If there is no signal or operation,the radio will reduce its power consumption.The battery power-saving function activates when the channel is unoccupied or has not been in operation. Low Battery Warning： If the battery power falls to the predetermined value during transmission,the transceiver will give out a voice prompt,please charge in time. Scrambling： It is a voice encryption mode which is different from sub audio. Companding： It is a function setting which prevents the inter-channel interference. CTCSS/DCS： The transceiver has 50 CTCSS and 208 DCS,also non-standard subaudio can be programmed! Functions Operation CDCSS Mode： It is valid only when you program the CDCSS on the channels. This function has two selections: "normal signaling" and "special signaling".Normal Signaling refers to the CDCSS codes on the channels is ordinary codes,we can�talk to�each other with the same CDCSS;Special Signaling refers to the CDCSS codes on the channels is special processed codes.When the transceivers in one company are programmed the same frequency with the same CDCSS and special signaling,they can avoid the signal interferences from the other companies’ transceivers. Functions Operation ▲We May Change The Specificatio ns For Technical Improvement Without Prior Notice. FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED app…

Text truncated - open the document above for the full version.

QA-FR-170-B Company: QUANZHOU KAILI ELECTRONICS CO., LTD. Ad d: Kaili Electronic Industrial Park(Photoelectric Information Base), Xiamei Town, Nanan, Quanzhou City, Fujian Province, China Tel: +86-595-26666977 Fax : +86-595-26666979 E-mail: [email protected] FCC Autho rization Date: 2020-04-20 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, QUANZHOU KAILI ELECTRONICS CO., LTD., hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratories Corp. on our b ehalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sinc erely Yours, Signature: Typed or Printed Name: Jacky Wang Title: Manager

QA-FR-171-A Company: QUANZHOU KAILI ELECTRONICS CO., LTD. Add: Kaili Electronic Industrial Park(Photoelectric Information Base), Xiamei Town, Nanan, Quanzhou City, Fujian Province, China Tel: +86-595-26666977 Fax: +86-595-26666979 E-mail: [email protected] FCC Confide ntial Authorization 2020-04-20 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AQX5KD-C70 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, QUANZHOU KAILI ELECTRONICS CO., LTD., hereby requests long-term confidential treatment of in formation accompanying this application as outlined below: •Block Diagram •Schematics •Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Typed or Printed Name: Jacky Wang Title: Manager

EXHIBIT A - EUT EXTERNAL PHOTOGRAPHS UHF Antenna

EXHIBIT B - EUT INTERNAL PHOTOGRAPHS

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “*”. SAR EVALUATION REPORT For QUANZHOU KAILI ELECTRONICS CO., LTD. Kaili Electronic Industrial Park(Photoelectric Information Base),Xiamei Town,Nanan,Quanzhou City,Fujian Province,China FCC ID: 2AQX5KD-C70 Report Type: Original Report Product Type: two way radio Report Number: RXM200420051-20A Report Date: 2020-06-16 Reviewed By: Rocky Xiao RF Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RXM200420051-20A SAR Evaluation Report 2 of 36 Attestation of Test Results EUT Information EUT Description two way radio Tested Model KD-C70 FCC ID 2AQX5KD-C70 Serial Number RXM200420051-SA-S1 Test Date 2020-04-21 MODE Max. SAR Level(s) Reported(W/kg) Limit (W/kg) PTT 1g Head SAR (Face Up) 0.74 1.6 1g Body SAR (Body Back) 1.18 Applicable Standards FCC 47 CFR part 2.1093 Radiofrequency radiation exposure evaluation: portable devices RF Exposure Procedures: TCB Workshop April 2019 IEEE1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques IEC 62209-1:2016 Measurement procedure for the assessment of specific absorption rate of human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices – Part 1: Devices used next to the ear (Frequency range of 300 MHz to 6 GHz) KDB procedures KDB 447498 D01 General RF Exposure Guidance v06 KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04 KDB 865664 D02 RF Exposure Reporting v01r02 Note: This wireless device has been shown to be capable of compliance for localizedspecific absorption rate (SAR) for General Population/Uncontrolled Exposure limits specified in FCC 47 CFR part 2.1093 and has been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and RF exposure KDB procedures. The results and statements contained in this report pertain only to the device(s) evaluated. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RXM200420051-20A SAR Evaluation Report 3 of 36 TABLE OF CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 4 EUT DESCRIPTION .................................................................................................................................................... 5 TECHNICAL SPECIFICATION ......................................................................................................................................... 5 REFERENCE, STANDARDS, AND GUIDELINES .................................................................................................. 6 SAR LIMITS ................................................................................................................................................................. 7 FACILITIES .................................................................................................................................................................. 8 DESCRIPTION OF TEST SYSTEM .......................................................................................................................... 9 EQUIPMENT LIST AND CALIBRATION ............................................................................................................. 14 EQUIPMENTS LIST & CALIBRATION INFORMATION .................................................................................................... 14 SAR MEASUREMENT SYSTEM VERIFICATION .............................................................................................. 15 LIQUID VERIFICATION ............................................................................................................................................... 15 SYSTEM ACCURACY VERIFICATION ........................................................................................................................... 16 SAR SYSTEM VALIDATION DATA ..................................................................................................................... 17 EUT TEST STRATEGY AND METHODOLOGY ................................................................................................. 18 TEST POSITIONS FOR DEVICE OPERATING NEXT TO A PERSON’S EAR........................................................................ 18 CHEEK/TOUCH POSITION ........................................................................................................................................... 19 EAR/TILT POSITION ................................................................................................................................................... 19 TEST POSITIONS FOR BODY-WORN AND OTHER CONFIGURATIONS .............................................................................. 20 TEST DISTANCE FOR SAR EVALUATION .................................................................................................................... 20 SAR EVALUATION PROCEDURE ................................................................................................................................. 21 OUTPUT POWER MEASUREMENT...................................................................................................................... 22 PROVISION APPLICABLE .…

Text truncated - open the document above for the full version.

PROBE CALIBRATION CERTIFICATES

Report No.: RXM200420051-20A Page 1 of 2 APPENDIX B EUT TEST POSITION PHOTOS Liquid depth ≥ 15cm Report No.: RXM200420051-20A Page 2 of 2 Face Up Setup Photo(25mm) BodyBack Setup Photo(0mm) 30mm 10mm 25mm

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. FCC PART 95 TEST REPORT For QUANZHOU KAILI ELECTRONICS CO., LTD. Kaili Electronic Industrial Park(Photoelectric Information Base), Xiamei Town, Nanan, Quanzhou City, Fujian Province, China Report Type: Original Report Product Type: two way radio Test Engineer: Stone Zhan g Re port Number: RXM200420051-00A Re port Date: 2020-06-15 Reviewed B y: Oscar Ye EMC Mana ger Prepared By: Bay Area Compliance Laboratories Corp. (Kunshan) No.248 Chenghu Road, Kunshan, Jiangsu province, China Tel: +86-0512-86175000 Fax: +86-0512-88934268 www.baclcorp.com.cn FCC ID: 2AQX5KD-C70 Bay Area Compliance Laboratories Corp. (Kunshan) Report No.: RXM200420051-00A FCC Part 95 Page 2 of 26 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 RELATED SUBMITTAL(S)/GRANT(S) ............................................................................................................................. 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 4 TEST FACILITY ............................................................................................................................................................. 4 SYSTEM TEST CONFIGURATION .......................................................................................................................... 5 DESCRIPTION OF TEST CONFIGURATION ...................................................................................................................... 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL I/O CABLE .................................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULTS ............................................................................................................................... 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 FCC §2.1093 - RF EXPOSURE .................................................................................................................................... 9 MEASUREMENT RESULT .............................................................................................................................................. 9 FCC §2.1046, §95.567 - RF OUTPUT POWER ........................................................................................................ 10 APPLICABLE STANDARD ............................................................................................................................................ 10 TEST PROCEDURE ...................................................................................................................................................... 10 TEST DATA ................................................................................................................................................................ 10 FCC §2.1047, §95.575 - MODULATION CHARACTERISTIC ............................................................................. 12 APPLICABLE STANDARD ............................................................................................................................................ 12 TEST PROCEDURE ...................................................................................................................................................... 12 TEST DATA ................................................................................................................................................................ 12 FCC §2.1049, §95.573, §95.579 - AUTHOURIZED BANDWIDTH AND EMISSION MASK ............................ 19 APPLICABLE STANDARD ............................................................................................................................................ 19 TEST PROCEDURE ...................................................................................................................................................... 19 TEST DATA ................................................................................................................................................................ 19 FCC §2.1053 & §95.579 - RADIATED SPURIOUS EMISSION ............................................................................ 23 APPLICABLE STANDARD ............................................................................................................................................ 23 TEST PROCEDURE ...............…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS Radiated Emissions (Below 1GHz) Radiated Emissions (Above 1GHz)