2AR2SAZ700T37CD Sound Machine

AZ700T_37_QSG_Sheet 1 .indd 1 W592 x H315mm Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited.or one of its affiliates, and MMD Hong Kong Holding Limited. is the warrantor in relation to this product. AZ700T_37_QSG_V1.0 AZ700T AZ700T_37_QSG_Sheet 1 .indd 2 1. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 2. A warning that batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. 3. where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readi ly operable 4. Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.50, dated June 24, 2007 CLASS 1 LASER PRODUCT MMD Hong Kong Holding Limited Units 1006-1007,10th Floor, C-Bons International Center,108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong FCC Regulatory ComplianceThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may n ot cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire d operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to oper ate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful in terference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equi pment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.ISED Regulatory ComplianceThis device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1 )This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit accepter tout brouillage radioélectr ique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.RF Exposure ComplianceThis equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated w ith minimum distance 20cm between the radiator and your body. ce matériel est conforme aux limites de dose d'exposition aux rayonnements FCC/IC énoncées pour un autre environnement.cet émet teur ne doit pas être situées ou opérant conjointement avec toute autre antenne ou l'émetteur. ce matériel doit être installé et ex ploité avec distance minimale 20cm entre le radiateur et votre corps. W592 x H315mm 120V~60Hz; 120V~60Hz; 120V~60Hz; 100 100 100 2.402GHz - 2.48GHz 7.52dBm 2.402GHz - 2.48GHz 7.52dBm 7.52dBm 2.402GHz - 2.48GHz （ for EU compliance ） （ for EU compliance ） （ for EU compliance ）

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name MMD Hong Kong Holding Limited Address Unit 1006, 10th Floor, C-Bons International Center 108 Wai Yip Street, Kwun Tong, Kowloon Grantee Code 2AR2S FCC ID Authorized Contact Name Tomas Guan Contact Email [email protected] Contact Phone 86-755-36358341 I, the unde rsigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and b elief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this applicati on, the Applicant is res ponsible for: ( 1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensur e that pr oduction units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsib le par ty and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accept s and agr ees to abide by the post market surveillance requirements . (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of th e Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. S ee 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and con ditions. Link to CFRs: htt ps://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature: Date: 2021-02-09 Print Name: Tomas Guan Title: Safety & Approbation Manager *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database 2AR2SAZ700T37

MMD Hong Kong Holding Limited Date: 2021‐02‐09 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID 2AR2SAZ700T37 To who m it may concern: We, the undersigned, hereby authorize SGS‐CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS‐CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, he reby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti‐Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge th at all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with MMD Hong Kong Holding Limited This authorization is valid until further written notice from the applicant. Print Name: Tomas Guan Title:Safety & Approbation Manager Signature: On behalf of Company: MMD Hong Kong Holding Limited Telephone: 86‐755‐36358341 E‐mail: tomas.guan@tpv‐tech.com

MMD Hong Kong Holding Limited TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: 2AR2SAZ700T37 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of th e documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY （Remark：如下资料需要短期保密请选择天数0，45,90或者180天，短期保密期间产品不能在美国市场上售卖。 Additionally, the applicant requests the following documents be held confidential until the device is marketed or 0 days from the grant date, whichever is less. If the device is marketed within 0 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. Delete any document that is NOT included in your application External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Tomas Guan Title:Safety & Approbation Manager Signature: On behalf of Company: MMD Hong Kong Holding Limited Telephone: 86‐755‐36358341 E‐mail: tomas.guan@tpv‐tech.com

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 6 External Photos for SZEM2101001463CR FCC ID: 2AR2SAZ700T37 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 6 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 6

Rating Label FCC Statement Label

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 9 Internal Photos for SZEM2101001463CR FCC ID: 2AR2SAZ700T37 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 9 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 9 Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 8 of 9 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 9 of 9

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146303 Page: 1 of 6 Keny Xu EMC Laboratory Manager SAR Evaluation Report Application No.: SZEM2102001463CR Applicant: MMD Hong Kong Holding Limited Address of Applicant: Unit 1006, 10th Floor, C-Bons International Center 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong, China Manufacturer: MMD Hong Kong Holding Limited Address of Manufacturer: Unit 1006, 10th Floor, C-Bons International Center 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong, China Factory: Yusan Technology(Shenzhen) Limited Address of Factory: Haoyi Technology Park, Nan Huan Road, Shajing West, Baoan Shenzhen, Guang Dong P.R. China Equipment Under Test (EUT): EUT Name: CD Sound Machine Model No.: AZ700T/37, AZ700T   Please refer to section 3 of this report which indicates which model was actually tested and which were electrically identical. Trade mark: FCC ID: 2AR2SAZ700T37 Standards: 47 CFR Part 1.1307 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2021-02-02 Date of Test: 2021-02-04 to 2021-03-04 Date of Issue: 2021-03-04 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146303 Page: 2 of 6 1 Version Revision Record Version Chapter Date Modifier Remark 01 2021-03-04 Original Authorized for issue by: Harry Wu /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146303 Page: 3 of 6 2 Contents Page 1 VERSION ................................................................................................................................................ 2 2 CONTENTS ............................................................................................................................................ 3 3 GENERAL INFORMATION ..................................................................................................................... 4 3.1 GENERAL DESCRIPTION OF EUT ......................................................................................................... 4 3.2 TEST LOCATION ................................................................................................................................ 5 3.3 TEST FACILITY .................................................................................................................................. 5 3.4 DEVIATION FROM STANDARDS ............................................................................................................ 5 3.5 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................... 5 3.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER .......................................................................... 5 4 SAR EVALUATION ................................................................................................................................. 6 4.1 RF EXPOSURE COMPLIANCE REQUIREMENT ........................................................................................ 6 4.1.1 Standard Requirement ................................................................................................................ 6 4.1.2 Limits .......................................................................................................................................... 6 4.1.3 EUT RF Exposure ....................................................................................................................... 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146303 Page: 4 of 6 3 General Information 3.1 General Description of EUT Power supply: AC120V 50/60Hz Cable(s): AC Power Cable:1.5m, Unshielded Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V3.0 Modulation Type: GFSK, pi/4DQPSK, 8DPSK Number of Channels: 79 Channel Spacing: 1MHz Spectrum Spread Technology: Frequency Hopping Spread Spectrum(FHSS) Antenna Type: Integral Antenna Antenna Gain: 0.54dBi Declaration of EUT Family Grouping: Model No.: AZ700T/37, AZ700T Only the model AZ700T was tested, since according to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model name, color and plug. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146303 Page: 5 of 6 3.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 3.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED a…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146302 Page: 1 of 86 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM2102001463CR Applicant: MMD Hong Kong Holding Limited Address of Applicant: Unit 1006, 10th Floor, C-Bons International Center 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong, China Manufacturer: MMD Hong Kong Holding Limited Address of Manufacturer: Unit 1006, 10th Floor, C-Bons International Center 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong, China Factory: Yusan Technology(Shenzhen) Limited Address of Factory: Haoyi Technology Park, Nan Huan Road, Shajing West, Baoan Shenzhen, Guang Dong P.R. China Equipment Under Test (EUT): EUT Name: CD Sound Machine Model No.: AZ700T/37, AZ700T   Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: FCC ID: 2AR2SAZ700T37 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2021-02-02 Date of Test: 2021-02-04 to 2021-03-04 Date of Issue: 2021-03-04 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146302 Page: 2 of 86 Revision Record Version Chapter Date Modifier Remark 01 2021-03-04 Original Authorized for issue by: Harry Wu/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146302 Page: 3 of 86 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.247(a)(1),(g),(h) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.5 47 CFR Part 15, Subpart C 15.247(b)(1) Pass 20dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.7 47 CFR Part 15, Subpart C 15.247(a)(1) Pass Carrier Frequencies Separation 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.2 47 CFR Part 15, Subpart C 15.247a(1) Pass Hopping Channel Number 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.3 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Dwell Time 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.6 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 7.8.8 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Emission Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146302 Page: 4 of 86 Declaration of EUT Family Grouping: Model No.: AZ700T/37, AZ700T Only the model AZ700T was tested, since according to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model name, color and plug. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM210200146302 Page: 5 of 86 3 Contents Page 1 COVER PAGE ..................................................................................................................................... 1 2 TEST SUMMARY ................................................................................................................................. 3 3 CONTENTS ......................................................................................................................................... 5 4 GENERAL INFORMATION .................................................................................................................. 7 4.1 DETAILS OF E.U.T. ......................................................................................................................... 7 4.2 DESCRIPTION OF SUPPORT UNITS .................................................................................................... 7 4.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 7 4.4 TEST LOCATION ............................................................................................................................. 8 4.5 TEST FACILITY ............................................................................................................................... 8 4.6 DEVIATION FROM STANDARDS ......................................................................................................... 8 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................. 8 5 EQUIPMENT LIST ............................................................................................................................... 9 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................13 6.1 ANTENNA REQUIREMENT ................................................................................................................13 6.1.1 Test Requirement: ..................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZEM2101001463CR FCC ID: 2AR2SAZ700T37 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs Conducted Emissions at AC Power Line (150kHz-30MHz) Radiated Emissions which fall in the restricted bands SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 Radiated Spurious Emissions