2AR2SPDT60True Wireless Earphones

USER MANUAL PDT60 True Wireless Earphones 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your True wireless earphones 3 What's in the box 3 Other devices 3 Overview of your True wireless earphones 4 3 Get started 5 Charge the battery 5 Pair the earpieces with your Bluetooth device for the st time 6 4 Use your headphones 7 Connect the earpieces to your Bluetooth device 7 Control ANC (active noise cancelation) 7 Manage your calls and music 8 LED indicator status 8 Voice Assistant 9 5 Reset the earpieces 10 6 Technical data 10 7 Notice 11 Declaration of conformity 11 Disposal of your old product and battery 11 Remove the integrated battery 11 Compliance with EMF 12 Environmental information 12 Notice of compliance 12 8 Trademarks 14 9 Frequently asked questions 15 Contents 1 Important safety instructions Hearing Safety Danger  To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can't hear what's around you. • You should use caution or temporarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headphones can cause hearing loss. • Using headphones with both ears covered while driving is not recommended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in trac or other potentially dangerous environments. General information To avoid damage or malfunction: Caution  Do not expose headphones to excessive heat  Do not drop your headphones.  Headphones shall not be exposed to dripping , splashing water.  Do not allow your headphones to be submerged in water.  Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.  If cleaning is required use a so doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.  The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.  Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion; • Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of ammable liquid or gas; • A battery subjected to extremely low air pressure that may result in an explosion or the leakage of ammable liquid or gas. About operating and storage temperatures and humidity • Store in a place where temperature is between -20°C (-4°F) and 50°C (122 °F) (up to 90% relative humidity. • Operate in a place where temperature is between 0°C (32°F) and 45°C (113 °F) (up to 90% relative humidity. • Battery life may be shorter in high or low temperature conditions. • Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types); 2 Your True wireless earphones What's in the box Porsche Design True wireless earphones Porsche Design PDT60 Replaceable rubber ear caps x 3 pairs Quick start guide Other devices A mobile phone or device (e.g. notebook, tablet, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see 'Technical data' on page 8). Congratulations on your purchase, and welcome to Porsche Design! With this Porsche Design True wireless earphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music. USB-C charging cable (for charging only) Global Warranty Safety leaet Quick start guide Warranty card Overview of your True wireless earphones Multi-function touch LED indicator (earpieces) LED indicator (charging box) USB-C charging slot 1 1 2 3 4 2 3 4 3 Get started Charge the battery Charging Box Note  Before you use your earpieces for the rst time, place the earpieces in the charging box and charge the battery for 3 hours for optimum battery capacity and lifetime.  Use only the original USB-C charging cable to avoid any damage.  Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces o. Connect one end of the USB cable into the charging box, and another end into the power source. • Charging process is veried by the white LED light on charging box. • When the charging box is fully charged, 4 LED indicators turn on. Tip  The charging box serves as a portable backup battery for charging the earpieces. When the charging box is fully charged, it supports 3 times full recharge cycle for the earpieces. The charging box starts charging. Tip  Normally, a full charge takes 2 hours (for the earpieces or charging box) by USB cable. Earpieces • LED indicator on earpieces turn on for 5s when fully charged. • LED indicator on earpieces turn on for 10s when charging. Place the earpieces in the charging box and close the slide. The earpieces start charging. The LED on both earpieces ash in white & blue alternately. Pair the earpieces with your Bluetooth device for the st time Push out the top cover from charging box. Make sure that the headset is fully charged and powered o. Single earpiece (Mono mode) Take either Right or Le earpiece out from charging box for Mono use. The earpiece will power on automatically. There will be a voice “Power on” from earpiece. Note Note  Aer powering on, if the earpieces cannot nd any previously connected Bluetooth device, it will automatically switch to pairing mode. Note  Take the second Earpiece from the charging box and they will pair each other automatically. …

Text truncated - open the document above for the full version.

MMD Hong Kong Holding Limited Declaration of Product We Name: MMD Hong Kong Holding Limited Address: Units 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon City: Hong Kong Country: China Declare that: Product description: True Wireless Earphones Type designation: PDT60 Trademark: PORSCHE DESIGN Hereby we confirm the Bluetooth 8DPSK modulation technology of this device is disabled by software control and end-users are not able to enable that function. Date: 2021-07-08 City: Hong Kong Name: Tomas Guan Function: Safety & Approbation Manager Signature:

Declaration of Authorization We Name: MMD Hong Kong Holding Limited Address: Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon City: Hong Kong State: N/A Country: China Declare that: Name Representative of agent: Ms. Rose Liu Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s): Product description: True Wireless Earphones Type designation: PDT60, PDT60xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Trademark: PORSCHE DESIGN FCC ID : 2AR2SPDT60 on our behalf. Date: 2020-11-06 City: Hong Kong Name: Tomas Guan Function: Safety & Approbation Manager Signature: Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 <2020-11-06> TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AR2SPDT60 PDT60, PDT60xx/yy (xx=AA-ZZ or blank denoted different color, yy=00-99 denoted different country destination) For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, (Signed) Name: Tomas Guan Company: MMD Hong Kong Holding Limited Address: Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Phone: 86-755-36358341 Fax: 86-755-26634642 E-Mail: [email protected]

Model Declaration Letter We, the undersigning company Company Name: MMD Hong Kong Holding Limited Address: Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Hereby confirm that the following products: Product description: True Wireless Earphones Type designation: PDT60,PDT60xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Trademark: PORSCHE DESIGN That all versions of the Model PDT60 and PDT60xx/yy are electrically equal except the following difference: 1. The model PDT60 and PDT60xx/yy are only differ in model name to distinguish between different markets. Date: 2020-11-06 Name: Tomas Telephone: 86-755-36358341 E-mail: [email protected] Signature:

Project No.: 2009C125 Page 2 of 37 Project No.: 2009C125 Page 3 of 37 Project No.: 2009C125 Page 4 of 37 Project No.: 2009C125 Page 5 of 37 Antenna Project No.: 2009C125 Page 6 of 37 Project No.: 2009C125 Page 7 of 37 Project No.: 2009C125 Page 8 of 37

PDT60 中文版 英文版 5.0 7.1 4.66 4 7.0 4.5 5.26 Sliding Cover wordmarks Pad-print on back cover 型号: PDT60 Ref no.: PDT60/00 输入: 5.0V 1A 输出: 5.0V 50mA 2 Battery Capacity: 3.7V 410mAh 1.517Wh 飞生(上海)电子科技有限公司 CMIIT ID: XXXXXXXXXX 中国制造 PTPZ2038000001 型号: PDT60 Ref no.: PDT60/00 输入: 5.0V 1A 输出: 5.0V 50mA 2 Battery Capacity: 3.7V 410mAh 1.517Wh 飞生(上海)电子科技有限公司 CMIIT ID: XXXXXXXXXX 中国制造 PTPZ2038000001 PTPZ2038000001 Model: PDT60 Ref no.: PDT60/00 MMD Hong Kong Holding Limited Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Input: 5.0V 1A Output: 5.0V 50mA 2 Battery Capacity: 3.7V 410mAh 1.517Wh FCC ID:2AR2SPDT60 IC:24589-PDT60 * Model: PDT60 Ref no.: PDT60/00 MMD Hong Kong Holding Limited Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Input: 5.0V 1A Output: 5.0V 50mA 2 Battery Capacity: 3.7V 410mAh 1.517Wh FCC ID:2AR2SPDT60 IC:24589-PDT60 * PTPZ2038000001

Project No.: 2009C125 Page 9 of 37 Project No.: 2009C125 Page 10 of 37 Project No.: 2009C125 Page 11 of 37 Project No.: 2009C125 Page 12 of 37 Project No.: 2009C125 Page 13 of 37 Project No.: 2009C125 Page 14 of 37

Project No.: 2009C125 Page 15 of 37 Project No.: 2009C125 Page 16 of 37 Project No.: 2009C125 Page 17 of 37 Project No.: 2009C125 Page 18 of 37 Left Project No.: 2009C125 Page 19 of 37

Project No.: 2009C125 Page 20 of 37 Project No.: 2009C125 Page 21 of 37 Project No.: 2009C125 Page 22 of 37 Project No.: 2009C125 Page 23 of 37

Project No.: 2009C125 Page 24 of 37 Project No.: 2009C125 Page 25 of 37 Project No.: 2009C125 Page 26 of 37 Right Project No.: 2009C125 Page 27 of 37 Project No.: 2009C125 Page 28 of 37

Project No.: 2009C125 Page 29 of 37 Project No.: 2009C125 Page 30 of 37 Project No.: 2009C125 Page 31 of 37 Project No.: 2009C125 Page 32 of 37 Project No.: 2009C125 Page 33 of 37

Project No.: 2009C125 Page 34 of 37 Project No.: 2009C125 Page 35 of 37 Project No.: 2009C125 Page 36 of 37 Project No.: 2009C125 Page 37 of 37

Report No.: BTL-FCCP-3-2009C125 Page 1 of 4 FCC RF EXPOSURE REPORT FCC ID: 2AR2SPDT60 Project No. : 2009C125 Equipment : True Wireless Earphones Brand Name : PORSCHE DESIGN Test Model : PDT60 Series Model : PDT60xx/yy (xx=AA-ZZ or blank denoted different color, yy=00-99 denoted different country destination) Applicant : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Factory : Eastech (Huizhou) Co., Ltd. Address : Dong Fong District, Xin Xu, Hui Yang, Hui Zhou City, Guang Dong 516226, China Date of Receipt : Sep. 16, 2020 Date of Test : Sep. 22, 2020 ~ Jun. 21, 2021 Issued Date : Jul. 06, 2021 Report Version : R00 Test Sample : Engineering Sample No.: DG20200917111 Standard(s) : FCC Guidelines for Human Exposure IEEE C95.1 & FCC Part 2.1091 FCC Title 47 Part 2.1091, OET Bulletin 65 Supplement C The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. Prepared by : Vincent Tan Approved by : Ethan Ma Add: No.3, Jinshagang 1st Road, Shixia, Dalang Town,Dongguan, Guangdong, China. Te l : +86-769-8318-3000 Web: www.newbtl.com Report No.: BTL-FCCP-3-2009C125 Page 2 of 4 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue Jul. 06, 2021 Report No.: BTL-FCCP-3-2009C125 Page 3 of 4 1. TEST FACILITY The test facilities used to collect the test data in this report is at the location of No.3,Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China. BTL's Test Firm Registration Number for FCC: 357015 BTL's Designation Number for FCC: CN1240 2. GENERAL CONCULUSION According to FCC KDB447498 D01, Appendix A, SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison Appendix A - SAR Test Exclusion Thresholds for 100 MHz - 6 GHz and < 50 mm MHz 5 10 15 20 25 30 35 40 45 50 mm 150 39 77 116 155 194 232 271 310 349 387 SAR Test Exclusion Thresholds (mW) 300 27 55 82 110 137 164 192 219 246 274 450 22 45 67 89 112 134 157 179 201 224 835 16 33 49 66 82 98 115 131 148 164 900 16 32 47 63 79 95 111 126 142 158 1500 12 24 37 49 61 73 86 98 110 122 1900 11 22 33 44 54 65 76 87 98 109 2450 10 19 29 38 48 57 67 77 86 96 3600 8 16 24 32 40 47 55 63 71 79 5200 7 13 20 26 33 39 46 53 59 66 5400 6 13 19 26 32 39 45 52 58 65 5800 6 12 19 25 31 37 44 50 56 62 Report No.: BTL-FCCP-3-2009C125 Page 4 of 4 3. TABLE FOR FILED ANTENNA Ant. Brand Model Name Antenna Type Connector Gain (dBi) Note 1 N/A Metal N/A -4.0 Left 2 N/A Metal N/A -4.5 Right Note: The antenna gain is provided by the manufacturer. 4. TEST RESULTS Tune up tolerance(dBm) BT LE ≤5 ≤1 For BT: Frequency (MHz) Max Tune-up power (dBm) Max Tune-up power (mW) Result Limit 2402 5 3.162 0.980 3.0 For LE: Frequency (MHz) Max Tune-up power (dBm) Max Tune-up power (mW) Result Limit 2440 1 1.259 0.393 3.0 Note: (1) Output power including tune up tolerance. (2) The maximum measured output peak power of this EUT is 3.162mW, less than 10mW at 5mm distance. Conclusion: No SAR evaluation required since transmitter power is below FCC threshold. End of Test Report

Report No.: BTL-FCCP-2-2009C125 Page 1 of 78 FCC Radio Test Report FCC ID: 2AR2SPDT60 This report concerns: Original Grant Project No. : 2009C125 Equipment : True Wireless Earphones Brand Name : PORSCHE DESIGN Test Model : PDT60 Series Model : PDT60xx/yy (xx=AA-ZZ or blank denoted different color, yy=00-99 denoted different country destination) Applicant : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Factory : Eastech (Huizhou) Co., Ltd. Address : Dong Fong District, Xin Xu, Hui Yang, Hui Zhou City, Guang Dong 516226, China Date of Receipt : Sep. 16, 2020 Date of Test : Sep. 22, 2020 ~ Jun. 21, 2021 Issued Date : Jul. 06, 2021 Report Version : R00 Test Sample : Engineering Sample No.:DG20200917111 for conducted, DG20200917112 for radiated. Standard(s) : FCC Part15, Subpart C (15.247) ANSI C63.10-2013 FCC KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. Prepared by : Vincent Tan Approved by : Ethan Ma Add: No.3, Jinshagang 1st Road, Shixia, Dalang Town,Dongguan, Guangdong, China. Te l : +86-769-8318-3000 Web: www.newbtl.com Report No.: BTL-FCCP-2-2009C125 Page 2 of 78 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, A2LA, or any agency of the U.S. Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO/IEC 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Report No.: BTL-FCCP-2-2009C125 Page 3 of 78 Table of Contents Page REPORT ISSUED HISTORY 6 1 . SUMMARY OF TEST RESULTS 7 1.1 TEST FACILITY 8 1.2 MEASUREMENT UNCERTAINTY 8 1.3 TEST ENVIRONMENT CONDITIONS 9 2 . GENERAL INFORMATION 10 2.1 GENERAL DESCRIPTION OF EUT 10 2.2 DESCRIPTION OF TEST MODES 12 2.3 PARAMETERS OF TEST SOFTWARE 13 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 14 2.5 SUPPORT UNITS 14 3 . AC POWER LINE CONDUCTED EMISSIONS TEST 15 3.1 LIMIT 15 3.2 TEST PROCEDURE 15 3.3 DEVIATION FROM TEST STANDARD 15 3.4 TEST SETUP 16 3.5 EUT OPERATING CONDITIONS 16 3.6 TEST RESULTS 16 4 . RADIATED EMISSION TEST 17 4.1 LIMIT 17 4.2 TEST PROCEDURE 18 4.3 DEVIATION FROM TEST STANDARD 18 4.4 TEST SETUP 19 4.5 EUT OPERATING CONDITIONS 20 4.6 TEST RESULT - 9 KHZ TO 30 MHZ 20 4.7 TEST RESULT - 30 MHZ TO 1000 MHZ 20 4.8 TEST RESULT - ABOVE 1000 MHZ 20 5 . BANDWIDTH TEST 21 5.1 LIMIT 21 5.2 TEST PROCEDURE 21 5.3 DEVIATION FROM STANDARD 21 5.4 TEST SETUP 21 Report No.: BTL-FCCP-2-2009C125 Page 4 of 78 Table of Contents Page 5.5 EUT OPERATION CONDITIONS 21 5.6 TEST RESULTS 21 6 . MAXIMUM OUTPUT POWER 22 6.1 LIMIT 22 6.2 TEST PROCEDURE 22 6.3 DEVIATION FROM STANDARD 22 6.4 TEST SETUP 22 6.5 EUT OPERATION CONDITIONS 22 6.6 TEST RESULTS 22 7 . CONDUCTED SPURIOUS EMISSION 23 7.1 LIMIT 23 7.2 TEST PROCEDURE 23 7.3 DEVIATION FROM STANDARD 23 7.4 TEST SETUP 23 7.5 EUT OPERATION CONDITIONS 23 7.6 TEST RESULTS 23 8 . POWER SPECTRAL DENSITY TEST 24 8.1 LIMIT 24 8.2 TEST PROCEDURE 24 8.3 DEVIATION FROM STANDARD 24 8.4 TEST SETUP 24 8.5 EUT OPERATION CONDITIONS 24 8.6 TEST RESULTS 24 9 . MEASUREMENT INSTRUMENTS LIST 25 10 . EUT TEST PHOTO 27 APPENDIX A - AC POWER LINE CONDUCTED EMISSIONS 31 APPENDIX B - RADIATED EMISSION - 9 KHZ TO 30 MHZ 34 APPENDIX C - RADIATED EMISSION - 30 MHZ TO 1000 MHZ 39 APPENDIX D - RADIATED EMISSION - ABOVE 1000 MHZ 42 APPENDIX E - BANDWIDTH 67 APPENDIX F - MAXIMUM OUTPUT POWER 70 Report No.: BTL-FCCP-2-2009C125 Page 5 of 78 Table of Contents Page APPENDIX G - CONDUCTED SPURIOUS EMISSION 72 APPENDIX H - POWER SPECTRAL DENSITY 77 Report No.: BTL-FCCP-2-2009C125 Page 6 of 78 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue. Jul. 06, 2021 Report No.: BTL-FCCP-2-2009C125 Page 7 of 78 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s): FCC Part15, Subpart C (15.247) Standard(s) Section Test Item Test Result Judgment Remark 15.207 AC Power Line Conducted Emissions APPENDIX A PASS ------ 15.247(d) 15.205(a) 15.209(a) Radiated Emissions APPENDIX B APPENDIX C APPENDIX D PASS ------ 15.247(a)(2) …

Text truncated - open the document above for the full version.

Report No.: BTL-FCCP-1-2009C125 Page 29 of 86 12. EUT TEST PHOTO AC Power Line Conducted Emissions Test Photos Report No.: BTL-FCCP-1-2009C125 Page 30 of 86 Radiated Emissions Test Photos 9 kHz to 30 MHz Report No.: BTL-FCCP-1-2009C125 Page 31 of 86 Radiated Emissions Test Photos 30 MHz to 1000 MHz Report No.: BTL-FCCP-1-2009C125 Page 32 of 86 Radiated Emissions Test Photos Above 1 GHz