2AR2STAH6506Wireless headphones with Noise Canceling

User manual Register your product and get support at www.philips.com/support TAH6506 6000 Series Headphones 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your Bluetooth over-ear headphones 3 What's in the box 3 Other devices 3 Overview of your Bluetooth wireless headphone 4 3 Get started 5 Charge the battery 5 Pair the headphones with your mobile phone 5 4 Use your headphones 6 Connect the headphone to your Bluetooth device 6 Manage your calls and music 6 5 Technical data 8 6 Notice 9 Declaration of conformity 9 Disposal of your old product and battery 9 Remove the integrated battery 9 Compliance with EMF 9 Environmental information 10 Notice of compliance 10 7 Trademarks 11 8 Frequently asked questions 12 Contents 1 Important safety instructions Hearing Safety  To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guide- lines when using your headphone. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can't hear what's around you. • You should use caution or tempo- rarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headphones can cause hearing loss. • Using headphones with both ears covered while driving is not recom- mended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in trac or other potentially dangerous environments. General information To avoid damage or malfunction: Danger  Do not expose headphones to excessive heat  Do not drop your headphones.  Headphones shall not be exposed to dripping or splashing.  Do not allow your headphones to be submerged in water.  Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.  If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.  The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.  Replacement of a battery with an incorrect type that can defeat a safeguard;  Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;  Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of ammable liquid or gas;  A battery subjected to extremely low air pressure that may result in an explosion or the leakage of ammable liquid or gas.  Never use your headphones when you are operating a motor vehicle, riding a bicycl e, running or walking in trac areas. It is dangerous and illegal in many places. About operating and storage temperatures and humidity • Operating temperature: 0°C (32°F) to 40°C (104°F) • Storage temperature: -10°C (14°F) to 45°C (113°F) • Operating humidity: 8% - 90% RH (No condensation) • Storage humidity: 5% - 90% RH (No condensation) • Maximum operating altitude: 3000m • Battery life may be shorter in high or low temperature conditions. Caution 2 Your Bluetooth over-ear headphones What's in the box Philips Bluetooth headphones Philips TAH6506 Quick start guide Other devices A mobile phone or device (e.g. note- book, PAD, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headphone (see 'Technical data' on page 8). Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/support. With this Philips over-ear headphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music; • enjoy noise cancelation. Carrying case USB-C charging cable (for charging only) Global Warranty Safety leaet Overview of your Bluetooth wireless headphone Muiti-Function Button (MFB) USB-C Indicator LED(White/Blue) Voice Mic Power Button ANC Mode Button 3.5mm Audio jack 1 2 3 4 5 6 7 1 2 3 4 5 7 6 3 Get started Charge the battery Note  Before you use your headphone for the rst time, charge the battery for 2 hours for optimum battery capacity and lifetime.  Use only the original USB charging cable to avoid any damage.  Finish your call before charging the headphone, as connecting the headphone for charging will power the headphone o. Connect the supplied USB charging cable to: • The USB type C charging slot on the headphones and; • The charger/USB port of a computer. Tip  Normally, a full charge takes 2 hours. Pair the headphones with your mobile phone Make sure that the headphones are fully charged and turned o. Make sure that the mobile phone is turned on and its Bluetooth feature is activated. The headphone remain in pairing mode for 5 minutes. Before you use the headphones with your mobile phone for the rst time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one. The following example shows you how to pair the headphones with your mobile phone. LED turns white during charging and turns o when the headphones in fully charged. Press and hold for 5 seconds until the blue and white LED ashes alternately. Philips TAH6506 Pair the headphones with the mobile phone. For detailed infor- mation, refer to the user manual of your mobile phone. Activate the Bluetooth feature of your mobile phone, select Philips TAH6506 Wired Connection 4 Use your headphones Connect the headphone to your Bluetooth device Turn on your mobile phone/ Bluetooth device. Press and hold the on/o button to turn the headphones on. Th…

Text truncated - open the document above for the full version.

Authority to Act as Agent [May 13, 2021] Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement (MMD Hong Kong Holding Limited) FCC ID: (2AR2STAH6506) To Whom It May Concern: We, (MMD Hong Kong Holding Limited), hereby authorized Shenzhen UnionTrust Quality and Technology Co., Ltd. to act as our Agent for the purpose of preparing application for FCC ID number (2AR2STAH6506) under all applicable parts of the FCC rules and regulations. We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: 36 months By: __________________________ Tomas Guan (Signature 1 ) (Print name) Title: Manager On behalf of: (MMD Hong Kong Holding Limited) Telephone: 86-755-36358341 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

1(1) [MMD Hong Kong Holding Limited] [May. 13, 2021] Attention: Application Examiner RE: Request for Confidentiality Applicant: [MMD Hong Kong Holding Limited] FCC ID: [2AR2STAH6506] To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request is hereby submitted by [MMD Hong Kong Holding Limited] to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:  Schematics  Detailed Block Diagrams  Detailed Operational/Functional Description Rationale for request for confidentiality: [MMD Hong Kong Holding Limited] has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.] If you have questions or need further information, please contact the undersigned. Sincerely, [Signature] [Tomas Guan] [ Manager] [MMD Hong Kong Holding Limited]

Page 1 of 3 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS EUT EXTERNAL PHOTOS EUT Photo EUT Photo Page 2 of 3 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo Page 3 of 3 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo

TAH6506 Philips Workmark Screen Printing UV ( TAH6506 Black UV( TAH6506 Black First PGD release for cost and feasibility study v0.1 2020.Sep.24 Authentication information v0.2 2020.Sep.28 Update color and workmark v0.32020.Nov.04 Add Approbation labe v0.42020.Nov.12 Add iconv0.52020.Nov.17 Update addressv0.62020.Nov.30 Add hop-pocketv0.72020.Dec.04 LHS RHS 4.0 20.0 25.0 TAH6506 1/3 2.28 2.00 2.00 1.00 Update information v0.82020.Dec.11 Update information v1.12020.Jan.25 Update workmarkv1.22020.Jan.29 Update hop-pocket workmark v0.92020.Dec.21 Update hop-pocket size v1.02020.Dec.31 12.0 v1.2 v1.2 L & R Workmark Screen Printing Screen Printing material color material color material color Pantone cool gray 9C material color v1.1 v0.8 v0.8 Authentication information A Reces engraving0.03,Gloss - - Authentication information B Radium carving Reces engraving,0.1,Gloss Reces engraving,0.15,Gloss Reces engraving,0.15,Gloss B Ear Can LHS C v1.2 v0.5 D E v0.7 Philips Workmarkhop-pocket I C C ICON PHLIPS workmark on Charging cable Charge workmark on Charging cable G - - v0.8 - - Approbation labe F H TAH6506 2/3 Ear Can RHS Ear Can LHS DD F E GHD DD E DD F 4.4*35 4.00 G H 10.00 TAH6506 3/3 70.0 65.0 170.0 175.0 45.0 10.0 80.9 10.0 I I

Page 1 of 3 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com APPENDIX 2 PHOTOS OF EUT CONSTRUCTIONAL DETAILS EUT INTERNAL PHOTOS EUT Photo EUT Photo Page 2 of 3 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo Page 3 of 3 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com EUT Photo EUT Photo BT Antenna

Page 2 of 9 Report No.: 210318025RFC-3 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-RSS102-V1.1 Version Version No. Date Description V1.0 May 18, 2021 Original Page 3 of 9 Report No.: 210318025RFC-3 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-RSS102-V1.1 CONTENTS 1. GENERAL INFORMATION ....................................................................................................................................... 4 1.1 CLIENT INFORMATION ........................................................................................................................................ 4 1.2 EUT INFORMATION ............................................................................................................................................ 4 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD ................................................................................. 4 1.4 OTHER INFORMATION ......................................................................................................................................... 5 1.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................................................... 5 1.6 DEVIATION FROM STANDARDS ............................................................................................................................ 5 1.7 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................. 5 1.8 OTHER INFORMATION REQUESTED BY THE CUSTOMER ........................................................................................ 5 2. EQUIPMENT LIST .................................................................................................................................................... 6 3. SAR TEST EXCLUSION EVALUATION ................................................................................................................... 6 3.1 REFERENCE DOCUMENTS FOR EVALUATION ........................................................................................................ 6 3.2 EXEMPTION LIMITS FOR ROUTINE EVALUATION – SAR EVALUATION .................................................................... 6 3.2.1 SAR TEST EXCLUSION THRESHOLD ........................................................................................................ 6 3.2.2 TEST PROCEDURE ................................................................................................................................. 8 3.3 MPE CALCULATION RESULTS ............................................................................................................................ 8 3.3.1 FOR BT ................................................................................................................................................. 8 APPENDIX 1 PHOTOS OF TEST SETUP ....................................................................................................................... 9 APPENDIX 1 PHOTOS OF EUT CONSTRUCTIONAL DETAILS ................................................................................... 9 Page 4 of 9 Report No.: 210318025RFC-3 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-RSS102-V1.1 1. GENERAL INFORMATION 1.1 CLIENT INFORMATION Applicant: MMD Hong Kong Holding Limited Address of Applicant: Unit 1006 , 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer: MMD Hong Kong Holding Limited Address of Manufacturer: Unit 1006 , 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong 1.2 EUT INFORMATION Product Name: Wireless headphones with Noise Canceling Model No. / HVIN: TAH6506 Add. Model No. : TAH6506xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Trade Mark: or PHILIPS DUT Stage: Production Unit EUT Supports Function: 2.4 GHz ISM Band: Bluetooth 5.0 Software Version: V0.1 Hardware Version: V03 Sample Received Date: April 23, 2021 Sample Tested Date: April 26, 2021 to May 10, 2021 Note: The additional model TAH6506xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) is identical with the test model TAH6506 except the model number for marketing purpose. 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD For BT_LE Frequency Band: 2400 MHz to 2483.5 MHz Frequency Range: 2402 MHz to 2480 MHz Bluetooth Version: Bluetooth LE Type of Modulation: GFSK Number of Channels: 40 Channel Separation: 2 MHz Antenna Type: PCB Antenna Antenna Gain: 0 dBi Maximum Peak Power: -3.84dBm Page 5 of 9 Report No.: 210318025RFC-3 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng Science and Technology Park, Longhua District, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-RSS102-V1.1 For BT_EDR Frequency Band: 2400 MHz to 2483.5 MHz Frequency Range: 2402 MHz to 2480 MHz Bluetooth Version: Bluetooth BR + EDR Modulation Technique: Frequency Hopping Spread Spectrum(FHSS) Type of Modulation: GFSK, π/4DQPSK, 8DPSK Number of Channels: 79 Channel Separation: 1 MHz Antenna Type: PCB antenna Antenna Gain: 0 dBi Maximum Peak Power: 5.847 dBm 1.4 …

Text truncated - open the document above for the full version.

Page 2 of 32 Report No.: 210318025RFC-1 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng science and technology park, Longhua district, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-RSS247-V1.1 Version Version No. Date Description V1.0 May 18, 2021 Original Page 3 of 32 Report No.: 210318025RFC-1 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng science and technology park, Longhua district, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] http://www.uttlab.com UTTR-RF-RSS247-V1.1 CONTENTS 1. GENERAL INFORMATION ....................................................................................................................................... 4 1.1 CLIENT INFORMATION ........................................................................................................................................ 4 1.2 EUT INFORMATION ............................................................................................................................................ 4 1.2.1 GENERAL DESCRIPTION OF EUT ............................................................................................................ 4 1.2.2 DESCRIPTION OF ACCESSORIES .............................................................................................................. 5 1.3 PRODUCT SPECIFICATION SUBJECTIVE TO THIS STANDARD ................................................................................. 5 1.4 OTHER INFORMATION ......................................................................................................................................... 5 1.5 DESCRIPTION OF SUPPORT UNITS ...................................................................................................................... 5 1.6 TEST LOCATION ................................................................................................................................................. 6 1.7 TEST FACILITY ................................................................................................................................................... 6 1.8 DEVIATION FROM STANDARDS ............................................................................................................................ 6 1.9 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................. 6 1.10 OTHER INFORMATION REQUESTED BY THE CUSTOMER ........................................................................................ 6 1.11 MEASUREMENT UNCERTAINTY ........................................................................................................................... 7 2. TEST SUMMARY ...................................................................................................................................................... 8 3. EQUIPMENT LIST .................................................................................................................................................... 9 4. TEST CONFIGURATION ........................................................................................................................................ 10 4.1 ENVIRONMENTAL CONDITIONS FOR TESTING ...................................................................................................... 10 4.1.1 NORMAL OR EXTREME TEST CONDITIONS ............................................................................................. 10 4.1.2 RECORD OF NORMAL ENVIRONMENT..................................................................................................... 10 4.2 TEST CHANNELS ............................................................................................................................................. 10 4.3 EUT TEST STATUS .......................................................................................................................................... 10 4.4 TEST SETUP .................................................................................................................................................... 11 4.4.1 FOR RADIATED EMISSIONS TEST SETUP ................................................................................................ 11 4.4.2 FOR CONDUCTED EMISSIONS TEST SETUP ............................................................................................ 12 4.4.3 FOR CONDUCTED RF TEST SETUP ........................................................................................................ 13 4.5 SYSTEM TEST CONFIGURATION ........................................................................................................................ 13 4.6 DUTY CYCLE ................................................................................................................................................... 14 5. RADIO TECHNICAL REQUIREMENTS SPECIFICATION .................................................................................... 15 5.1 REFERENCE DOCUMENTS FOR TESTING ............................................................................................................ 15 5.2 ANTENNA REQUIREMENT ................................................................................................................................. 15 5.3 CONDUCTED PEAK OUTPUT POWER ................................................................................................................. 16 5.4 6 DB BANDWIDTH & OCCUPIED BANDWIDTH ..................................................................................................... 17 5.5 POWER SPECTRAL DENSITY ............................................................................................................................ 19 5.6 CONDUCTED OUT OF BAND EMISSION ...............................…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng science and technology park, Longhua district, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com APPENDIX 1 PHOTOS OF TEST SETUP Radiated emission Test Setup (30 MHz~1 GHz) Radiated emission Test Setup (Above 1 GHz) Page 2 of 2 FCC ID: 2AR2STAH6506 IC: 24589-TAH6506 Shenzhen UnionTrust Quality and Technology Co., Ltd. Address: Unit D/E of 9/F and 16/F, Block A, Building 6, Baoneng science and technology park, Longhua district, Shenzhen, China Tel: +86-755-28230888 Fax: +86-755-28230886 E-mail: [email protected] Http://www.uttlab.com RF Conducted Test Setup