2AR2STAH9505Noise Cancellation Pro, Wireless Headphones

User manual Register your product and get support at www.philips.com/support Headphones 9000 Series TAH9505 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your Bluetooth over-ear headphones 3 What's in the box 3 Other devices 3 Overview of your Bluetooth wireless headset 4 3 Get started 5 Charge the battery 5 Pair the headphones with your mobile phone 5 4 Use your headphones 6 Connect the headphones to a Bluetooth device 6 Manage your calls and music 6 5 Technical data 8 6 Notice 9 Declaration of conformity 9 Disposal of your old product and battery 9 Remove the integrated battery 9 Compliance with EMF 9 Environmental information 10 Notice of compliance 10 7 Trademarks 11 8 Frequently asked questions 12 Contents 1 Important safety instructions Hearing Safety  To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guide- lines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts. • Do not turn up the volume so high that you can't hear what's around you. • You should use caution or tempo- rarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headphones can cause hearing loss. • Using headphones with both ears covered while driving is not recom- mended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in trac or other potentially dangerous environments. General information To avoid damage or malfunction: Danger  Do not expose headphones to excessive heat  Do not drop your headphones.  Headphones shall not be exposed to dripping or splashing.  Do not allow your headphones to be submerged in water.  Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.  If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the product.  The integrated battery shall not be exposed to excessive heat such as sunshine, re or the like.  Replacement of a battery with an incorrect type that can defeat a safeguard;  Disposal of a battery into re or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;  Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of ammable liquid or gas;  A battery subjected to extremely low air pressure that may result in an explosion or the leakage of ammable liquid or gas.  Never use your headphones when you are operating a motor vehicle, riding a bicycl e, running or walking in trac areas. It is dangerous and illegal in many places. About operating and storage temperatures and humidity • Operating temperature: 0°C (32°F) to 40°C (104°F) • Storage temperature: -10°C (14°F) to 45°C (113°F) • Operating humidity: 8% - 90% RH (No condensation) • Storage humidity: 5% - 90% RH (No condensation) • Maximum operating altitude: 3000m • Battery life may be shorter in high or low temperature conditions. Caution 2 Your Bluetooth over-ear headphones What's in the box Philips Bluetooth headphones Philips TAH9505 Quick start guide Other devices A mobile phone or device (e.g. note- book, PAD, Bluetooth adapters, MP3 players etc) which supports Bluetooth and is compatible to the headset (see 'Technical data' on page 8). Congratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/welcome. With this Philips over-ear headphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music; • enjoy noise cancelation. Plane Adaptor Carrying case USB charging cable (for charging only) Audio cable Global Warranty Safety leaet Overview of your Bluetooth wireless headset Voice Assistant Button Indicator LED(White/Blue) Touch Pad USB-C Power Button ANC Mode Button 2.5mm Audio jack 1 2 3 4 5 6 7 Voice Mic 8 1 2 3 5 4 6 7 8 9 3 Get started Charge the battery Charging case Note  Before you use your headset for the rst time, place the headsets in the charging case and charge the battery for 2 hours for optimum battery capacity and lifetime.  Use only the original USB charging cable to avoid any damage.  Finish your call before charging the headset, as connecting the headset for charging will power the headset o. Connect the supplied USB charging cable to: • The USB type C charging slot on the headphones and; • The charger/USB port of a computer. Tip  Normally, a full charge takes 2 hours. Pair the headphones with your mobile phone Make sure that the headphones are fully charged and turned o. Make sure that the mobile phone is turned on and its Bluetooth feature is activated. The headphone remain in pairing mode for 2 minutes. Before you use the headphones with your mobile phone for the rst time, pair it with a mobile phone. A successful pairing establishes a unique encrypted link between the headphones and mobile phone. The headphones store the last 8 devices in the memory. If you try to pair more than 8 devices, the earliest paired device is replaced by the new one. The following example shows you how to pair the headphones with your mobile phone. LED turns white during charging and turns o when the headphones in fully charged. Press and hold for 5 seconds until the blue and white LED ashes alternately. Philips TAH9505 Pair the headphones with the mobile phone. For detailed infor- mation, refer to the user manual of your mobile phone. Activate the Bluetooth feature of your mobile phone, select Philips TAH9505 Wired Connection Note  When streaming audio from Device 1, receiving a call from Device 2 will automatically pause D…

Text truncated - open the document above for the full version.

RF_160, Issue 02 Declaration of Authorization We Name: MMD Hong Kong Holding Limited Address: Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon City: Hong Kong Country: China Declare that: Name Representative of agent: Ms. Rose Liu Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s): Product description: Noise Cancellation Pro，Wireless Headphones Type designation: TAH9505,TAH9505xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Trademark: PHILIPS FCC ID : 2AR2STAH9505 on our behalf. Date: 2020-11-09 City: Hong Kong Name: Tomas Guan Function: Safety & Approbation Manager Signature: Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

FCC, Request for non-disclosure Date: 21-Nov-2018 RF_501, Issue 8 Page 1 of 1 Company Name: MMD Hong Kong Holding Limited Address: Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon City: Hong Kong Country: China To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2AR2STAH9505 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (See notes below): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Date: 2020-11-09 Name and signature of applicant: Tomas Guan Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! The planned date should stated in the RF731 application form. 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Model Declaration Letter We, the undersigning company Company Name: MMD Hong Kong Holding Limited Address: Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Hereby confirm that the following products: Product description: Noise Cancellation Pro，Wireless Headphones Type designation: TAH9505,TAH9505xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Trademark: PHILIPS That all versions of the Model TAH9505 and TAH9505xx/yy are electrically equal except the following difference: 1. The model TAH9505 and TAH9505xx/yy are only differ in model name to distinguish between different markets. Date: 2020-11-09 Name: Tomas Telephone: 86-755-36358341 E-mail: [email protected] Signature:

Report No.: 2010C032 Page 2 of 13 Report No.: 2010C032 Page 3 of 13 Report No.: 2010C032 Page 4 of 13

RightLeft Model No.: TAH9505 Refer No.: TAH9505BK/00 CAN ICES-3(B)/NMB-3(B) IC: 24589-TAH9505 FCC ID: 2AR2STAH9505 DC Input: 5V — 0.5A S/N.: JTPQ2044000001 12.096mm 18.508mm 28.948mm 5mm 5mm MMD HK HOLDING LTD. Unit 1006,10/F, C-Bons int'l center, H.K 飞生 (上海) 电子科技有限公司 Made in China 4.875mm 12.828mm 29.004 5mm 5mm 7mm TAH9505BK/00 Right Left Model No.: TAH9505 Refer No.: TAH9505BK/27 CAN ICES-3(B)/NMB-3(B) IC: 24589-TAH9505 FCC ID: 2AR2STAH9505 DC Input: 5V — 0.5A S/N.: JTPR2044000001 MMD HK HOLDING LTD. Unit 1006,10/F, C-Bons int'l center, H.K 飞生 (上海) 电子科技有限公司 Made in China 12.096mm 18.133mm 28.948mm 5mm 5mm 4.875mm 12.828mm 29.004 5mm 5mm 7mm TAH9505BK/27 RightLeft Model No.: TAH9505 Refer No.: TAH9505BK/93 DC Input: 5V — 0.5A CMIIT ID: XXXXXXXXXX MMD HK HOLDING LTD. Unit 1006,10/F, C-Bons int'l center, H.K 飞生 (上海) 电子科技有限公司 Made in China 4.875mm 7.803mm 1.114mm 29.005mm 10.039mm 6.5mm 6.514mm 18.202mm 28.542mm TAH9505BK/93 季紫薇 郭海泉 石成伟 设 计 DRAWN BY 2020.11.06 2020.11.06 2020.11.06 审 核 CHECKED BY 核 准 APPVE BY 零件料号 PART NO. 比 例 SCALE 描述 Describe 规格镭雕 机 型 MODEL NO. 图纸名称 DWG NAME BH-1056 ############# 绘图视角 PROJECTION 单 位 METRIC MM 1:1 3NOD DIGITAL TECHNOLOGY ■REACH■RoHs■CA65CFRl303PFOSPAHsFORMALDEHYDE/甲醛≤***PPM HALOGEN FREE/无卤 THIS DRAWING，AND IT'S INHERANT DESIGN CONCEPTS，ARE THE PROPERTY OF 3NOD AND AS SUCH MAY NOT BE COPIED，REPRODUCED，0R GIVEN TO THIRD PARTIES WITHOUT THE WRITTEN CONSENT OF 3NOD． 技术要求: 1. 图中标注 尺寸为FAI尺寸。 2. 图中标注 尺寸为重点检验尺寸, 要求CPK≥1。 FAI ** * FORM NO:FM-QMP005-36 A.0 版本/Rev修订描述/REVISION DESCRIPTION 第一次发行 修正地址删除"-07" V.0 V.1 2020.10.28 2020.11.06 修订/REVISED BY日期/DATE 控制复印 注: TAH9505BK/00 & TAH9505BK/27只有Refer No与SN差别

Report No.: 2010C032 Page 5 of 13 Report No.: 2010C032 Page 6 of 13 ANT Report No.: 2010C032 Page 7 of 13 Report No.: 2010C032 Page 8 of 13 Report No.: 2010C032 Page 9 of 13 Report No.: 2010C032 Page 10 of 13 Report No.: 2010C032 Page 11 of 13 Report No.: 2010C032 Page 12 of 13 Report No.: 2010C032 Page 13 of 13

Report No.: BTL-FCCP-3-2010C032 Page 1 of 4 FCC RF EXPOSURE REPORT FCC ID: 2AR2STAH9505 Project No. : 2010C032 Equipment : Noise Cancellation Pro, Wireless Headphones Brand Name : PHILIPS or Test Model : TAH9505 Series Model : TAH9505xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Applicant : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Factory : Shenzhen 3nod Digital Technology Co., Ltd Address : 4/F, And Section A, 1/F, Workshop 15, Zhongfu Road, Tangxiayong Community, Songgang Neighbourhood, Bao’An District, Shenzhen City, Guangdong Province, P.R.C Date of Receipt : Oct. 13, 2020 Date of Test : Oct. 13, 2020 ~ Oct. 26, 2020 Issued Date : Nov. 18, 2020 Report Version : R00 Test Sample : Engineering Sample No.: DG2020101462 Standard(s) : FCC Guidelines for Human Exposure IEEE C95.1 & KDB447498 D01 The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. Prepared by : Vincent Tan Approved by : Ethan Ma Add: No.3, Jinshagang 1st Road, Shixia, Dalang Town,Dongguan, Guangdong, China. Te l : +86-769-8318-3000 Web: www.newbtl.com Report No.: BTL-FCCP-3-2010C032 Page 2 of 4 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue. Nov. 18, 2020 Report No.: BTL-FCCP-3-2010C032 Page 3 of 4 1. TEST FACILITY The test facilities used to collect the test data in this report is at the location of No.3,Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China. BTL's Test Firm Registration Number for FCC: 357015 BTL's Designation Number for FCC: CN1240 2. GENERAL CONCULUSION According to FCC KDB447498 D01, Appendix A, SAR Test Exclusion Thresholds for 100 MHz – 6 GHz and ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where  f(GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison Appendix A - SAR Test Exclusion Thresholds for 100 MHz - 6 GHz and < 50 mm MHz 5 10 15 20 25 30 35 40 45 50 mm 150 39 77 116 155 194 232 271 310 349 387 SAR Test Exclusion Thresholds (mW) 300 27 55 82 110 137 164 192 219 246 274 450 22 45 67 89 112 134 157 179 201 224 835 16 33 49 66 82 98 115 131 148 164 900 16 32 47 63 79 95 111 126 142 158 1500 12 24 37 49 61 73 86 98 110 122 1900 11 22 33 44 54 65 76 87 98 109 2450 10 19 29 38 48 57 67 77 86 96 3600 8 16 24 32 40 47 55 63 71 79 5200 7 13 20 26 33 39 46 53 59 66 5400 6 13 19 26 32 39 45 52 58 65 5800 6 12 19 25 31 37 44 50 56 62 Report No.: BTL-FCCP-3-2010C032 Page 4 of 4 3. TABLE FOR FILED ANTENNA Ant. Manufacturer Model Name Antenna Type Connector Gain (dBi) 1 Shenzhen Kaipushen Communication Technology Co. LTD N/A PCBA N/A 1.57 4. TEST RESULTS Tune up tolerance (dBm) BT LE ≤3.5 ≤0.0 For BT: Max. Output Power (dBm) Max. Output Power (mW) Limit (mW) 3.5 2.24 10 For LE: Max. Output Power (dBm) Max. Output Power (mW) Limit (mW) 0.0 1.00 10 Note: (1) Output power including tune up tolerance. (2) The maximum measured output peak power of this EUT is 2.24mW, less than 10mW at 5mm distance. Conclusion: No SAR evaluation required since transmitter power is below FCC threshold. End of Test Report

Report No.: BTL-FCCP-2-2010C032 Page 1 of 62 FCC Radio Test Report FCC ID: 2AR2STAH9505 This report concerns: Original Grant Project No. : 2010C032 Equipment : Noise Cancellation Pro, Wireless Headphones Brand Name : PHILIPS or Test Model : TAH9505 Series Model : TAH9505xx/yy (xx=AA-ZZ or blank denoted different color; yy=00-99 denoted different country destination) Applicant : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Manufacturer : MMD Hong Kong Holding Limited Address : Unit 1006, 10th Floor, C-Bons International Center, 108 Wai Yip Street, Kwun Tong, Kowloon, Hong Kong Factory : Shenzhen 3nod Digital Technology Co., Ltd Address : 4/F, And Section A, 1/F, Workshop 15, Zhongfu Road, Tangxiayong Community, Songgang Neighbourhood, Bao’An District, Shenzhen City, Guangdong Province, P.R.C Date of Receipt : Oct. 13, 2020 Date of Test : Oct. 13, 2020 ~ Oct. 26, 2020 Issued Date : Nov. 18, 2020 Report Version : R00 Test Sample : Engineering Sample No.: DG2020101462 for conducted, DG2020101463 for radiated. Standard(s) : FCC Part15, Subpart C (15.247) ANSI C63.10-2013 FCC KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliance with the requirement of the relative standards by BTL Inc. Prepared by : Vincent Ta n Approved by : Ethan Ma Add: No.3, Jinshagang 1st Road, Shixia, Dalang Town,Dongguan, Guangdong, China. Te l : +86-769-8318-3000 Web: www.newbtl.com Report No.: BTL-FCCP-2-2010C032 Page 2 of 62 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, A2LA, or any agency of the U.S. Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO/IEC 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Report No.: BTL-FCCP-2-2010C032 Page 3 of 62 Table of Contents Page REPORT ISSUED HISTORY 6 1 . SUMMARY OF TEST RESULTS 7 1.1 TEST FACILITY 8 1.2 MEASUREMENT UNCERTAINTY 8 1.3 TEST ENVIRONMENT CONDITIONS 9 2 . GENERAL INFORMATION 10 2.1 GENERAL DESCRIPTION OF EUT 10 2.2 DESCRIPTION OF TEST MODES 12 2.3 PARAMETERS OF TEST SOFTWARE 12 2.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 2.5 SUPPORT UNITS 13 3 . AC POWER LINE CONDUCTED EMISSIONS TEST 14 3.1 LIMIT 14 3.2 TEST PROCEDURE 14 3.3 DEVIATION FROM TEST STANDARD 14 3.4 TEST SETUP 15 3.5 EUT OPERATING CONDITIONS 15 3.6 TEST RESULTS 15 4 . RADIATED EMISSION TEST 16 4.1 LIMIT 16 4.2 TEST PROCEDURE 17 4.3 DEVIATION FROM TEST STANDARD 17 4.4 TEST SETUP 18 4.5 EUT OPERATING CONDITIONS 19 4.6 TEST RESULT - 9 KHZ TO 30 MHZ 19 4.7 TEST RESULT - 30 MHZ TO 1000 MHZ 19 4.8 TEST RESULT - ABOVE 1000 MHZ 19 5 . BANDWIDTH TEST 20 5.1 LIMIT 20 5.2 TEST PROCEDURE 20 5.3 DEVIATION FROM STANDARD 20 5.4 TEST SETUP 20 Report No.: BTL-FCCP-2-2010C032 Page 4 of 62 Table of Contents Page 5.5 EUT OPERATION CONDITIONS 20 5.6 TEST RESULTS 20 6 . MAXIMUM OUTPUT POWER 21 6.1 LIMIT 21 6.2 TEST PROCEDURE 21 6.3 DEVIATION FROM STANDARD 21 6.4 TEST SETUP 21 6.5 EUT OPERATION CONDITIONS 21 6.6 TEST RESULTS 21 7 . CONDUCTED SPURIOUS EMISSION 22 7.1 LIMIT 22 7.2 TEST PROCEDURE 22 7.3 DEVIATION FROM STANDARD 22 7.4 TEST SETUP 22 7.5 EUT OPERATION CONDITIONS 22 7.6 TEST RESULTS 22 8 . POWER SPECTRAL DENSITY TEST 23 8.1 LIMIT 23 8.2 TEST PROCEDURE 23 8.3 DEVIATION FROM STANDARD 23 8.4 TEST SETUP 23 8.5 EUT OPERATION CONDITIONS 23 8.6 TEST RESULTS 23 9 . MEASUREMENT INSTRUMENTS LIST 24 10 . EUT TEST PHOTO 26 APPENDIX A - AC POWER LINE CONDUCTED EMISSIONS 30 APPENDIX B - RADIATED EMISSION - 9 KHZ TO 30 MHZ 33 APPENDIX C - RADIATED EMISSION - 30 MHZ TO 1000 MHZ 38 APPENDIX D - RADIATED EMISSION - ABOVE 1000 MHZ 41 APPENDIX E - BANDWIDTH 54 APPENDIX F - MAXIMUM OUTPUT POWER 56 Report No.: BTL-FCCP-2-2010C032 Page 5 of 62 Table of Contents Page APPENDIX G - CONDUCTED SPURIOUS EMISSION 58 APPENDIX H - POWER SPECTRAL DENSITY 61 Report No.: BTL-FCCP-2-2010C032 Page 6 of 62 REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue. Nov. 18, 2020 Report No.: BTL-FCCP-2-2010C032 Page 7 of 62 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standard(s): FCC Part15, Subpart C (15.247) Standard(s) Section Test Item Test Result Judgment Remark 15.207 AC Power Line Conducted Emissions APPENDIX A PA S…

Text truncated - open the document above for the full version.

Report No.: BTL-FCCP-1-2010C032 Page 29 of 87 12. EUT TEST PHOTO AC Power Line Conducted Emissions Test Photos Report No.: BTL-FCCP-1-2010C032 Page 30 of 87 Radiated Emissions Test Photos 9 kHz to 30 MHz Report No.: BTL-FCCP-1-2010C032 Page 31 of 87 Radiated Emissions Test Photos 30 MHz to 1000 MHz Report No.: BTL-FCCP-1-2010C032 Page 32 of 87 Radiated Emissions Test Photos Above 1 GHz