2ARBZ-KFPXXWAir Purifier

INSTRUCTION MANUAL AIR PURIFIER Model No: KF-P29W Model No: KF-P30W Keep these instructions for further reference Thank you for purchasing the innovative KF-P29W or KF-P30W air purifier. We wish you many ears of healthy indoor air with this efficient and effective product. Ensure that all safety precautions are followed when using this electrical appliance for the proper operation of the device. These instructions describe the safety precautions to be observed during operation. They are designed to prevent injuries or damage to this device. SAFETY PRECAUTIONS: 1.Cleaning the unit, while it is plugged in may result in electric shock, electric spark and serious injury. Unplug the unit before cleaning or maintenance. 2.Our air purifier is used 50 / 60Hz, 50Hz -60Hz. 3.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 4.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ➔Reorient or relocate the receiving antenna. ➔Increase the separation between the equipment and receiver. ➔Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ➔Consult the dealer or an experienced radio/TV technician for help. 5.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. WARING: To reduce the risk of fire, electric shock or injury, read and understand this user guide before operation this appliance. 1.This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. 2.Do not operate unite if cord or plug is damaged. Doing so can result in electric shock. Discard the damaged unite or take if to an authorized service facility for examination and /or repair. 3.Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. DO NOT ROUTE CORD UNDER FURNITURE OR APPLIANCES. Arrange cord away from traffic area and where it will not be tripped over. 4.Only use the air purifier as described in this manual. 5.Do not handle the unit with wet hands. Thoroughly dry your hands before handling any part of the air purifier. 6.Hair, loose clothing and body parts can get caught in the machine resulting in injury. Keep hair, loose clothing and body parts away from openings and moving parts. 7.Do not unplug by pulling on the cord. Doing so may result in electrical spark or fire, Unplug the unit by grasping. And pulling the plug. 8.Do not use an extension cord. 9.Do not place the air purifier near sources of heat, such as: stove tops, ovens, radiators or computers. 10.Unplug the appliance from the power supply before servicing. 11.This equipment should be inspected frequently and the dirt that has collected should be removed regularly to prevent excessive accumulation that may result in flashover or fire. 12.Do not use the air purifier outdoors or on wet surfaces. 13.Do not use the air purifier in an enclosed space where flammable, combustible or explosive gases are present. 14.Do not use in an area where toxic vapors, flammable dust or oxygen tanks are present. Checked the location and make sure these elements are not present. 15.Do not place open flames, including candles, directly in front of the air purifier. 16.It is important to keep all objects away from the air intake grille. 17.Place the air purifier on a flat, solid, stable surface. Always allow 38cm of clearance on all sides of the purifier. Never place the unit on soft surfaces such as a bed or sofa. 18.Position the air purifier so that the dirty air is not drawn across your head or body while sitting or sleeping. 19.Place the air purifier so the plug on the power cord easily reaches a standard electrical outlet for a polarized plug. 20.Children should be supervised when product is in used. Do not allow children to play on or near the air purifier. Keep children’s hair, loose clothing, and body parts away from/ out of the intake grille, bents, holes, or openings. 21.This product is suitable for use with solid-state speed controls. 22.Do not let cord hang over edge of table or counter. 23.RISK OF ELECTRIC Shock-these servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.''(2020 年 9 月新增) 24.This product complies with the maximum allowable concentration of ozone of 0.050 pa by volume (ppmv) in a 24-h period. 25.Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. PRODUCT DIAGRAM: FEATURES AND OPERATION: NEGATIVE IONS: Negative Ions abound in our natural environments such as forests, waterfalls, mountains and seaside. Negative ions are useful for enhancing the metabolism and homeostasis of the human body. This air p…

Text truncated - open the document above for the full version.

[2020.10.19] Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement Foshan Samyoo Electronic Co.,Ltd FCC ID: 2ARBZ-KFXXW (Model for KFP29W , CZAP101SBK , CZAP101SWT， KFP30W ，CZAP102SWT) To Whom It May Concern: We, Foshan Samyoo Electronic Co.,Ltd, hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2ARBZ-KFXXW under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement i s 2020.10.19. The Limited Agency Agreement expires on 2021.3.19, unless sooner terminated or extended by written notice t o Intertek Testing Services and the Federal Communications Commission. This i s t o advise that we are i n full compliance with th e Anti-Drug Abuse Act. The applicant i s not subject t o a denial of federal benefits pursuant t o Section 5301 of the Anti-Drug Act of 1988, 2 1 U.S.C. 862, and no party to th e application is subject t o a denial of federal benefits pursuant t o that section. If you have any questions or comments, please do not hesitate t o contact me. Sincerely, [Signature] [Type Name] Lei Li [Type Title] Manager

1(1) [2020.10.19] Attention: Application Examiner RE: Request for Confidentiality Applicant: Foshan Samyoo Electronic Co.,Ltd FCC ID: 2ARBZ-KFPXXW （ Model for KFP29W，KFP30W， CZAP101SBK， CZAP101SWT， CZAP102SWT） To Whom It May Concern: Permanent Confidentiality [Complete this section if permanent confidentiality is requested] Request is hereby submitted by Foshan Samyoo Electronic Co.,Ltd to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential: [Select one or more of items below, as appropriate] •Schematics •Detailed Block Diagrams •Detailed Operational/Functional Description Rationale for request for confidentiality: Foshan Samyoo Electronic Co.,Ltd has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] If you have questions or need further information, please contact the undersigned. Sincerely, [Signature] [Type Title] Manager Foshan Samyoo Electronic Co.,Ltd

KFP29W KFP30W

Model: KFP29W Model: KFP30W

KFP30W KFP30W and KFP29W KFP30W and KFP29W KFP30W and KFP29W KFP30W and KFP29W KFP30W and KFP29W Power supply KFP30W and KFP29W Power supply KFP29W control board KFP29W control board KFP30W control board KFP30W control board KFP29W and KFP30W Wi-Fi KFP30W and KFP29W motor KFP30W and KFP29W motor KFP30W and KFP29W motor KFP30W and KFP29W KFP30W and KFP29W KFP30W and KFP29W

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Job No.: 200624024GZU FCC ID: 2ARBZ-KFPXXW Version: 08 July 2020 Page 1 of 2 FCC RF Exposure-Mobile (MPE) RF Exposure Compliance Requirement Model no.: KFP30W 1. Standard requirement Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. (a) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)(mW/cm 2 ) Averaging Times ׀E׀ 2 ׀, H׀ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)(mW/cm 2 ) Averaging Times ׀E׀ 2 ׀, H׀ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- F/1500 30 1500-100000 -- -- 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Job No.: 200624024GZU FCC ID: 2ARBZ-KFPXXW Version: 08 July 2020 Page 2 of 2 FCC RF Exposure-Mobile (MPE) 2. MPE Calculation Method E (V/m)=(30*P*G) 0.5 /d Power Density: Pd(W/m 2 )=E 2 /377 E=Electric Field (V/m) P=Peak RF output Power (W) G=EUT Antenna numeric gain (numeric) d= Separation distance between radiator and human body (m) The formula can be changed to Pd= (30*P*G)/(377*d 2 ) From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. 3. Calculated Result and Limit Frequency (MHz) Antenna Gain (dBi) Antenna Gain (Numeric) Maximum Peak Output Power (dBm) Maximum Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 2412-2462 2.5 1.78 17 50.12 0.01773 1 Complies Remark: The antenna gain and maximum peak output power were declared by applicant. Test Location: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch All tests were performed at: Room102/104, No 203, KeZhu Road, Science City, GETDD Guangzhou, China

Foshan Samyoo Electronic Co.,Ltd TEST REPORT SCOPE OF WORK EMC TESTING–REFER TO PAGE 2 REPORT NUMBER 200624024GZU-001 ISSUE DATE [REVISED DATE] 06-January-2021 [---------------------] PAGES 72 DOCUMENT CONTROL NUMBER FCC WIFI-d © 2017 INTERTEK TEST REPORT Room 02, & 101/E201/E301/ E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Telephone: +86 20 8213 9688 Facsimile: +86 20 3205 7538 www.intertek.com.cn This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Version: 10 June 2019 Page 2 of 72 FCC WIFI-d Applicant Name & Address : Foshan Samyoo Electronic Co.,Ltd No.2, 6th East Road Jiangcun Industrial Zone, Leliu, Shunde Foshan, Guangdong China Manufacturing Site : Same as applicant Intertek Report No: FCC ID: 200624024GZU-001 2ARBZ-KFPXXW Test standards 47 CFR PART 15 Subpart C: 2019 section 15.247 Sample Description Product : Air Purifier Model No. : KFP29W, KFP30W, CZAP101SBK, CZAP101SWT, CZAP102SWT Electrical Rating : 120 VAC, 60 Hz, 0.25 A, 12 W Serial No. : Not Labeled Date Received : 24 June 2020 Date Test Conducted : 10 September 2020-21 September 2020 Prepared and Checked By Dean Liu Project Engineer Approved By: Helen Ma Team Leader TEST REPORT Intertek Report No.: 200624024GZU-001 Version: 10 June 2019 Page 3 of 72 FCC WIFI-d CONTENT TEST REPORT ........................................................................................................................... 1 CONTENT ............................................................................................................................. 3 1.0 TEST RESULT SUMMARY ............................................................................................ 4 2.0 GENERAL DESCRIPTION ............................................................................................. 5 2.1 P RODUCT DESCRIPTION ........................................................................................................ 5 2.2 RELATED SUBMITTAL(S) GRANTS ........................................................................................... 6 2.3 TEST METHODOLOGY .......................................................................................................... 6 2.4 TEST FACILITY ..................................................................................................................... 6 3.0 SYSTEM TEST CONFIGURATION ................................................................................. 6 3.1 J USTIFICATION .................................................................................................................... 6 3.2 EUT EXERCISING SOFTWARE ................................................................................................. 7 3.3 S PECIAL ACCESSORIES .......................................................................................................... 8 3.4 MEASUREMENT UNCERTAINTY .............................................................................................. 8 3.5 E QUIPMENT MODIFICATION ................................................................................................. 8 3.6 SUPPORT EQUIPMENT LIST AND DESCRIPTION .......................................................................... 9 4.0 MEASUREMENT RESULTS ........................................................................................ 10 4.1 ANTENNA REQUIREMENT ................................................................................................... 10 4.2 6 DB BANDWIDTH (DTS BANDWIDTH).................................................................................. 11 4.3 MAXIMUM PEAK CONDUCTED OUTPUT POWER ..................................................................... 18 4.4 P EAK POWER SPECTRAL DENSITY ......................................................................................... 25 4.5 OUT OF BAND CONDUCTED EMISSIONS ................................................................................ 32 4.6 O UT OF BAND RADIATED EMISSIONS .................................................................................... 38 4.7 RADIATED EMISSIONS IN RESTRICTED BANDS ......................................................................... 39 4.8 BAND EDGES REQUIREMENT ............................................................................................... 63 4.9 C ONDUCTED EMISSION TEST ............................................................................................... 67 5.0 TEST EQUIPMENT LIST ............................................................................................. 71 TEST REPORT Intertek Report No.: 200624024GZU-001 Version: 10 June 2019 Page 4 of 72 FCC WIFI-d 1.0 TEST RESULT SUMMARY Test Item Test Requirement Test Method Result Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15.203 FCC PART 15 C section 15.247 (c) and Section 15.203 PASS 6 dB Bandwidth (DTS bandwidth) FCC PART 15 C section 15.2…

Text truncated - open the document above for the full version.

Radiated Emission (Below 1GHz) Radiated Emission (Above 1GHz) AC Conducted Emission