2ARPKDTM-02LTelemetics mangement Terminal

DTM-02L USER’S GUIDE ©All Rights Reserved DTM-02L User’s Guide Rev.: 1.0 +Update: 23/09/19 Rev. 1.0 Page 2 of 17 This page contains confidential information, which is protected by copyright and is proprietary to DIV No part of this document may be used, copied, disclosed or conveyed to another party without prior written consent of DIV Revision History Revision Issue Date Author Scope 1.0 2019/08/14 Lim.J.H Initial Release DTM-02L User’s Guide Rev.: 1.0 +Update: 23/09/19 Rev. 1.0 Page 3 of 17 This page contains confidential information, which is protected by copyright and is proprietary to DIV No part of this document may be used, copied, disclosed or conveyed to another party without prior written consent of DIV Contents 1 WARNINGS FOR SAFETY OPERATION ................................................................ 5 2 INTRODUCTION ...................................................................................................... 8 3 OVERVIEW .............................................................................................................. 9 3.1 Components ................................................................................................................................................... 9 3.3 Features ........................................................................................................................................................ 10 4 HARDWARE DESCRIPTIONS ............................................................................... 11 4.1 DTM-02L ....................................................................................................................................................... 11 4.1.1 I/O Connector ...................................................................................................................................... 12 4.1.2 Status LED .......................................................................................................................................... 14 5 HOW TO USE......................................................................................................... 15 5.1 User Registration ......................................................................................................................................... 15 5.2 LTE Mode Operation ................................................................................................................................... 15 6 SPECIFICATIONS .................................................................................................. 16 6.1 DTM-02L ....................................................................................................................................................... 16 7 LIMITED WARRANTY ............................................................................................ 17 DTM-02L User’s Guide Rev.: 1.0 +Update: 23/09/19 Rev. 1.0 Page 4 of 17 This page contains confidential information, which is protected by copyright and is proprietary to DIV No part of this document may be used, copied, disclosed or conveyed to another party without prior written consent of DIV Figure FIGURE １ LIN-Q SYSTEM .................................................................................................................................. 8 FIGURE ２ DTM-02L TERMINAL ........................................................................................................................ 9 FIGURE ３ DTM-02L TERMINAL ...................................................................................................................... 11 FIGURE ４ I/O CONNECTOR ............................................................................................................................. 12 FIGURE ５ STATUS LED ................................................................................................................................... 14 Table TABLE 1 DESCRIPTIONS FOR EACH PARTS OF DTM-01 ............................................................................ 11 TABLE 2 PIN DESCRIPTIONS FOR I/O CONNECTOR.................................................................................... 13 TABLE 3 STATUS LED....................................................................................................................................... 14 TABLE 4 DTM-02L SPECIFICATIONS .............................................................................................................. 16 DTM-02L User’s Guide Rev.: 1.0 +Update: 23/09/19 Rev. 1.0 Page 5 of 17 This page contains confidential information, which is protected by copyright and is proprietary to DIV No part of this document may be used, copied, disclosed or conveyed to another party without prior written consent of DIV 1 Warnings for safety operation This is to protect your safety and property. Please read this manual carefully before using.  Operational Environment - The operating voltage of this products is between 9Vdc and 34Vdc. Please use the specified operating volgage. - Use within the specified temperature range. - This product is specialized for industrial vehicles.  Insallation Precaustions - Insallation and wiring require professional skills. Be sure to install it with the help of a propessional. Incorrect insallation and wiring can cuase the fire or malfuncation. - When installing the product, install it so that it does not inferfere with the operation of safety devices such as airbags and brake levers...etc. - Insall in a location free from moisture. It may cuase damage or accidents if it is installed in places where water or rain is splashed or dusty. - When wiring, be sure to check the position of pipes, tanks, electric wiring, etc., and pay special attention to avoid interference or contact. - Use specified cables and components. - Be careful not to fall down when installing in a place where the ceiling and vibration of the vehicle are severe. - Do not block the vent or heat sink. It may cause the fire. - Protect…

Text truncated - open the document above for the full version.

Page 2 of 4 Applicant Confidentiality Letter SAMPLE HOIMYUNG ICT Corporation 1203, 8th Daeryungtechnotown, 96, Gamasan‐ro, Geumcheon‐gu Seoul 08501 Korea (Republic Of) Tel. +82 2 6958 3500 / Fax. +82 2 6958 3530 FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 December 30, 2019 Subject: Confidentiality Request for Exhibits under FCC ID: 2ARPKDTM‐02L To Whom It May Concern: Pursuant of Section 0.457 and 0.459 of the Commission’s Rules and KDB 726920 D01 Confidentiality Request Procedures, we hereby request that the exhibits listed below, submitted in support of the certification application for FCC ID: 2ARPKDTM‐02L, be withheld permanently from public disclosure. Exhibit Type Document Number or NameVersion/ or Revision File Name Block Diagram DTM‐02L_Block Diagramn/aDTM‐02L_Block Diagram.pdf Operational Description DTM‐02L_Operational description n/aDTM‐02L_Operational description.pdf Parts list DTM‐02L_Part List n/aDTM‐02L_Part List.pdf Schematics DTM‐02L_Schematicsn/aDTM‐02L_Schematics.pdf This request includes third party confidentiality for items not allowed to be accessed by HOIMYUNG ICT Corporation. The below third party and its confidentiality documents are listed as below: Documents only accessible by Quectel Wireless Solutions Company Limited: Exhibit Type Document Number or NameVersion/ or Revision File Name Schematics EG25‐G_SCH_V2.1_20180723 V2.1 EG25‐G_SCH_V2.1_20180723.pdf Operational Description EG25‐G Operational description n/aEG25‐G Operational description.pdf Block Diagram EG25‐G_Block Diagramn/aEG25‐G_Block diagram.pdf Parts list EG25‐G_V2.1_BOM V2.1 EG25‐G_V2.1_BOM.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04‐1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Page 3 of 4 Exhibit Type Document Number or NameVersion/ or Revision File Name External photos External photos_DTM‐02Ln/aExternal photos_DTM‐02L.pdf Internal photos Internal photos_DTM‐02Ln/aInternal photos_DTM‐02L.pdf Test setup photos Test setup photos_DTM‐02Ln/aTest setup photos_DTM‐02L.pdf User Manual DTM‐02L_User Manualn/aDTM‐02L_User Manual.pdf Best Regards, Jongrak Geun / General Manager HOIMYUNG` ICT Corporation

HOIMYUNG ICT Corporation 1203, 8th Daeryungtechnotown, 96, Gamasan-ro, Geumcheon-gu Seoul 08501 Korea (Republic Of) Tel. +82 2 6958 3500 / Fax. +82 2 6958 3530 December 24, 2019 To : TIMCO ENGENEERING INC. Dear Sir/Madam, Re: Declaration states : EUT uses a previously certified module. We, Hoimyung ICT, hereby declare that this EUT is leveraging previously certified LTE&WCDMA module. It does not operate with the module simultaneously. There is no change to module and that the module when installed into this host system(DTM-02L) is identical to what was previously certified under FCC ID: XMR201903EG25G, IC: 10224A-201903EG25G. There is no change to modules when installed into the host system. The original module test reports accurately represents test results under the new host application. Host: Telemetics mangement Terminal Model name: DTM-02L FCC ID: 2ARPKDTM-02L IC: 24504-DTM02L Certified LTE Module*: LTE Module Model name: EG25-G, EG25-G MINIPCIE FCC ID: XMR201903EG25G IC: 10224A-201903EG25G Test report Number: HR/2019/1001601(FCC), HR/2019/1001603(IC) *Host product will operate in LTE Band 12/5/4/2/7, WCDMA 850/1900 and will disable other bands that were previously listed in original modules filing via software. Sincerely, Client’s signature : Client’s name / title : Jongrak Geun / General Manager Contact information / address : [email protected]

HOIMYUNG ICT Corporation 12F 1203, Gamasanro 96 Geumcheon-gu, Seoul-si, 08501, South Korea Tel. +82 2 6958 3500 / Fax. +82 2 6958 3530 CONFIDENTIALITY REQUEST Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 September 23, 2019 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, HOIMYUNG ICT Corporation, requests confidentiality for the following products: FCC ID Number Product Title/Model 2ARPKDTM-02L Telemetics mangement Terminal / DTM-02L The following exhibits contain trade secrets and proprietary information that could be of benefit to our competitors regarding the design of our product. This material is not customarily available to the general public and we request that it be withheld from public inspection. We request that the following information submitted be held permanent confidential treatment. Permanent Confidential Request -. Schematics -. Block Diagram -. Operational Description -. Parts list We also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give temporary confidentiality of commercially sensitive information prior to product release. Short-Term Confidential Request -. External Photos -. Internal Photos -. Test set-up photo -. User Manual If you have any questions, please feel free to contact me at the address shown below. Sincerely, Client’s signature : Client’s name / title : Jongrak Geun / General Manager Contact information / address : [email protected]

\\kdata\Project\2019(일반)\KP19-03001~03500\KP19-03075_회명정보통신_DTM-02L\시험성적서(RF)\FCC\2. Word\접수자료\POA_Letter_140225.docx HOIMYUNG ICT Corporation 12F 1203, Gamasanro 96 Geumcheon-gu, Seoul-si, 08501, South Korea Tel. +82 2 6958 3500 / Fax. +82 2 6958 3530 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: September 23, 2019 SUBJECT: FCC Application for 2ARPKDTM-02L To Whom It May Concern: We, the undersigned, hereby authorize Ms. Athena Kim at KCTL Inc. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Ms. Athena Kim at KCTL Inc. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, Client’s signature : Client’s name / title : Jongrak Geun / General Manager Contact information / address : [email protected]

Page3of3 ThirdPartyConfidentialityLetterSAMPLE FCCLaboratory 7435OaklandMillsRoad Columbia,MD21046 DateJanuary3,2020 Subject:ThirdPartyConfidentialityRequestforExhibitsunderFCCID:XMR201903EG25G ToWhomItMayConcern: PursuantofSection0.457and0.459oftheCommission’sRulesandKDB726920D01 ConfidentialityRequestProcedures,weherebyrequestthattheexhibitslistedbelow,submittedin supportofthecertificationapplicationforFCCID:2ARPKDTM-02L,bewithheldpermanentlyfrom publicdisclosure: ExhibitTypeDocumentNumberorNameVersion/or Revision FileName SchematicsEG25-G_SCH_V2.1_20180723n/aEG25-G_SCH_V2.1_20180723 Operational Description EG25-GOperationaldescriptionn/aEG25-GOperationaldescription BlockDiagramEG25-G_BlockDiagramn/aEG25-G_BlockDiagram BOMEG25-G_V2.1_BOMn/aEG25-G_V2.1_BOM Theaboveexhibits,ownedsolelybyQuectelWirelessSolutionsCo.,Ltd.andpreviously submittedtotheCommissionspermanentconfidentialexhibitsforthecertificationofthe QuectelWirelessSolutionsCo.,Ltd.modulewithFCCID:XMR201903EG25G,containtradesecretsand proprietaryinformationnotcustomarilyreleasetothepublic.Thepublicdisclosureofthesematerials maybeharmfultoQuectelWirelessSolutionsCo.,Ltd.andprovideunjustifiedbenefitstoits competitors.GranteeofFCCID:2ARPKDTM-02Lisauthorizedtoreferencetheseexhibitsinits applicationbutnotauthorizedtoaccessthem.TimcoEngineering,Inc.,asaTCB,isauthorizedtoaccess theseexhibitsandincludetheminthefilingforFCCID:2ARPKDTM-02Lunderpermanentconfidentiality. BestRegards, Signature Signee’sPrintedNameJeanHu TitleManager

Page 1 of 5 1 Photographs - EUT Constructional Details FCC ID.: XMR201903EG25G Test PCB board Photo EG25-G Page 2 of 5 Page 3 of 5 EG25-G MINIPCIE Page 4 of 5 Page 5 of 5

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval External photos of EUT http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval

1 Photographs - EUT Constructional Details FCC ID.: XMR201903EG25G EG25-G This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only. EG25-G MINIPCIE This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

http://www.kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Internal photos of EUT http://www .kctl.co.kr This test report shall not be reproduced, except in full, without the written approval http://www .kctl.co.kr This test report shall not be reproduced, except in full, without the written approval Chip Antenna (Bluetooth Low Energy) Chip Antenna (LTE, WCDMA)

Data sheet of Multilayer Chip Antenna Part No. : ALA931C5 January 23, 2008 AMOTECH Co., LTD. 5B 1L, Namdong Industrial complex, 617 Namchondong, Namdonggu, Incheon, Korea Notes The contents of this data sheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. AMOTECH - 2 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 1. SPECIFICATIONS 1.1 Electrical Specifications No ITEM SPEC. Remark 1 Frequency Range 2.4 ~2.485 GHz for ISM 2 VSWR 2.5 : 1 max. 3 Gain Avg. -3 dBi min. 4 Polarization Linear 5 Azimuth Beam Pattern Omni-directional 6 Impedance Nominal 50 Ω ※ These values are measured on the matched reference test board. ※ ALA931C5 has higher self-resonance-frequency than ALA931C4. 1.2 Mechanical Specifications No ITEM SPEC. Remark 1 Internal Electrode Ag Pb-free 2 External Electrode Ag/Ni/Sn Pb-free 3 Dimensions (L x W x H) 9.0 x 3.0 x 1.2 mm 4 Unit Weight 97 ± 9 mg 5 Operating Temperature -35 ~ +85 °C 1.3 Appearance and Dimensions No Name Function Material 1 External Electrode Soldering, Input Port Ag/Ni/Sn 2 Direction index Indication of Input Port Ceramic 4 Ceramic Body - Ceramic 3 Model & Serial No. index - Ceramic 5 External Electrode Soldering Ag/Ni/Sn AMOTECH - 3 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 2. MEASUREMENT 2.1 Reference Test Board for Measurement Chip Antenna Matching Stage SMA Connector GND [Unit : mm] 2.2 Diagram for VSWR measurement Network Analyzer Styrofoam AUT AMOTECH - 4 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 2.3 Diagram for radiation gain and pattern measurements iMac A. Anechoic chamber spec. Parameters Condition Unit Chamber size 8x4x4 m Temperature 21.5 °C Humidity 55 % RH Measurement S21 (8753ES) System software Midas (Orbit/FR) B. Measurement coordinates Measurement Plane Symbol Rotating direction Azimuth Azimuth x→y Elevation1 E1 z→x Elevation2 E2 z →-y x y z -y Azimuth E1 E2 AMOTECH - 5 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 3. MEASUREMENT RESULT 3.1 VSWR & Smithchart A. Matching Value (recommend for reference testboard only) ③① ② ① N/C ② 2.7 nH ③ 1.2 nH B. Measured data (for ALA931C5) AMOTECH - 6 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 3.2 Radiation Gain and Pattern [Measured data table] Peak Gain (dBi) Average Gain (dBi) Remark Azimuth 2.8 1.0 @2.45 GHz Elevation1 3.5 -0.7 @2.45 GHz Elevation2 1.7 -1.6 @2.45 GHz [ ALA931C5 radiation pattern : [email protected] ] AMOTECH - 7 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) [ ALA931C5 radiation pattern : [email protected] ] [ALA931C5 Radiation Pattern : [email protected] ] AMOTECH - 8 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 4. SUGGESTED LAYOUT & MATCHING CIRCUIT 4.1 Layout (recommend only) 4.2 Matching Circuit (recommend only) L – type T - type π- type For usable matching, the ground stability must be guaranteed with sufficient via holes and the case effects should be considered. Finally, using one or more lumped chip elements and a tuning stub are recommended for better results. AMOTECH - 9 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 5. RELIABILITY TEST No ITEM TEST CONDITION TEST REQUIREMENTS 1 Adhesive Strength of Termination 1. Applied force on SMD chip till detached point from PCB. F SMD PAD PCB 1. No mechanical damage by forces applied on the right. 2. Strength (F) > 7 kgf 2 Tensile Strength 1. Wire : 0.6~0.8 tined Cu wire F Clamp Wire 1. No mechanical damage by forces applied on the right. 2. Strength (F) > 3 kgf 3 Thermal Shock (Temperature Cycle) 1. 1 cycle / step 1 : -40 ± 3°C, 30 min step 2 : +125 ± 3°C, 30 min 2. Number of cycle : 30 3. Measure after left for 48 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) 4 High Temperature Resistance 1. Temperature : +125 ± 5°C 2. Time : 1000 ± 24 hrs 3. Measure f C after left for 24 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) 5 Low Temperature Resistance 1. Temperature : -40 ± 5°C 2. Time : 1000 ± 24 hrs 3. Measure f C after left for 48 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) 6 Humidity (Steady Condition) 1. Humidity : 85 % RH 1. Temperature : +85 ± 3°C 2. Time : 1000 ± 24 hrs 3. Measure f C after left for 48 hrs min. at room temperature 1. No visual damage 2. Within electric spec (VSWR) AMOTECH - 10 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 6. SOLDERING RECOMMENDATIOS 6.1 Reflow Soldering Profile [ Soldering Reflow Profile for Pb-free ] 6.2 Soldering Land Pattern 10.2 1.3 3.2 7.6 (unit : mm) AMOTECH - 11 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 7. PACKING 7.1 Tape Dimension (unit : mm) A0 3.30±0.10 P0 4.00±0.10 E 1.75±0.10 B0 9.30±0.10 P1 8.00±0.10 F 7.50±0.10 K0 1.30±0.10 P2 2.00±0.10 W 16.00±0.30 D0 1.55±0.05 t 0.30±0.05 7.2 Taping Style 7.3 Packing Unit Quantity Size Reel 1,000 ea Φ7” x 16mm Small Box 3,000 ea (3 reel*1,000ea/reel) 185 * 185 * 68 (mm 3 ) Medium Box 15,000 ea (5 small box*3,000ea/small box) 365 * 200 * 200 (mm 3 ) Large Box 42,000 ea (14 small box*3,000ea/small box) 390 * 390 * 280 (mm 3 ) AMOTECH - 12 - MULTILAYER CHIP ANTENNA Januay 2008 (Rev5.0) 7.4 Description of Packing Label AMOTECH CO., LTD. Name of Company 617 5B 1LT, Namchon-Dong, Namdong-Gu, Inchon, Korea Address of Manufacture Multilayer Chip Antenna Name of Component Type : ALA931C5 Lot No : MA09A4050101 Quantity : 1,000 pcs Quantity : 1,000 pcs Date : 2007/10/01 Date : 2007/10/01 8. STORAGE CONDITION A. Storage environment must be at an ambient temperature of 15~35°C and an ambient humidity of 45~75 % RH. (MSL Level 2) B. Chip antenna can experience degradation of termination solderability when subjected to high temperature of humidity, or if exposed to sulfur or chlorine gases. C. Avoid mechanical shock (ex. falling) to the chip antenna to prevent mechanical cracking inside of the ceramic dielectric due to its own weight. ALA : Amotech LTCC Antenna 931 : Chip Size C5 : Version & Frequency index MA : Mass-product Antenna 09 : Chip Size A5 : Version & F…

Text truncated - open the document above for the full version.

Notes The contents of this data sheet are subject to change without notice. Please confirm the specifications and delivery conditions when placing your order. Data sheet Main Internal Antenna Part No. : AMMAL004 Revision no Content Page Date Name 0 First, documented - 2016.12.22 H.W. Oh Designed Checked Approved Date / / / / AMOTECH CO., LTD 5B-1L, 617, NAMCHON-DONG, NAMDONG-GU, INCHOEN-CITY, KOREA TEL : 82-32-821-0363 FAX : 82-32-811-0283 Designed Checked Approved 12 / 22 12 / 22 12 / 22 AMOTECH Patent Pending - 3 - MAIN CHIP ANTENNA 1.2. Mechanical Specifications Electrode Copper - Dimensions (L x W x H) 35.0(L) x 9.0(W) x 3.2(H) mm Operating Temperature -40 ~ +85 °C 1.3 Marking ● : 1 pin positon L004 : Model No. YY : Year (ex: 2015 → 15 ) WW : Week (ex: 1 st week→01, 7 th week→07) 2-Ø1.6 Via ●L004_YYWW AMOTECH AMOTECH Patent Pending - 4 - MAIN CHIP ANTENNA 2. MEASUREMENT 2.1. SET for Measurement Board size mm: 141x50x1.6T Antenna Radiation coordinate system 2.2. Electrical Characteristic ◆ S 11 (VSWR) - VSWR @ EV Board - AMOTECH Patent Pending - 7 - MAIN CHIP ANTENNA LTE23 LTE40 XY plane XZ plane YZ plane AMOTECH Patent Pending - 8 - MAIN CHIP ANTENNA LTE7, LTE41 XY plane XZ plane YZ plane AMOTECH Patent Pending - 9 - MAIN CHIP ANTENNA GSM850 LTE5 GSM900 LTE8 XY plane XZ plane YZ plane AMOTECH Patent Pending - 10 - MAIN CHIP ANTENNA DCS LTE3 PCS LTE2 XY plane XZ plane YZ plane AMOTECH Patent Pending - 11 - MAIN CHIP ANTENNA WCDMA1 LTE1 XY plane XZ plane YZ plane AMOTECH Patent Pending - 12 - MAIN CHIP ANTENNA 3. SOLDERING RECOMMENDATIONS 3.1. Soldering Land Pattern * PCB Thickness (mm): FR4 1.6T AMOTECH Patent Pending - 13 - MAIN CHIP ANTENNA 3.2. Matching circuit 3.3. Soldering Profile Solder paste : Sn/Ag/Cu:96.5/3.0/0.5 This product is designed for reflow soldering only. Do not use flow (wave) soldering. ① Use non-activated flux (Cl content 0.2% max.) ② Follow the recommended soldering conditions to avoid damage. ③ Reflow-cycle is max. 3times. C1 (Series) 2.2 pF C2 (Shunt) 0.5 pF C3 (Shunt) NC L2 (Series) 1.8 nH AMOTECH Patent Pending - 14 - MAIN CHIP ANTENNA 4. PACKING 4.1 Tape Dimension (unit : mm) 4.1.1 Size P2 2.00±0.15 P0 4.00±0.10 E W D0 P1 16.00±0.1 F t A0 MAX 6°이하 K0 B0 *10P0 40.00±0.20 A0 9.40±0.10 E 1.75±0.10 B0 35.50±0.10 F 26.20±0.10 K0 3.70±0.10 W 56.00±0.30 D0 1.50+0.1 -0.0 t 0.40±0.05 4.1.2 Surface resistance 1) Carrier tape : Max 10 11 Ω 2) Cover tape : Max 10 11 Ω 3) Reel : Max 10 11 Ω AMOTECH Patent Pending - 15 - MAIN CHIP ANTENNA 4.2 Description of Reel 4.2.1 Size ITEM DIA WIDTH CORE DIA HOLE Size(mm) 330.0 ±2 57.5 ± 1.0 80.0 ± 1.0 13.0 ± 0.3 4.2.2 Material 1) Plastic reel : GPPS (General Purpose Poly Styrene) resin 4.3 Description of Packing Box 4.3.1 Reel Size: 56 (W), Dia. Φ330 (mm) Quantity: 1,000ea/reel 4.3.2 Inner Box Size: 368 (W) x 346 (D) x 65 (T) (mm) Quantity: 1 reel (1,000 ea/reel × 1 reel = 1,000 ea) DIA WIDTH CORE DIA HOLE RoHS Compliance Label AMOTECH Patent Pending - 16 - MAIN CHIP ANTENNA 4.3.3 Outer Box Size: 405 (W) x 360 (D) x 300 (T) (mm) Quantity: 4 Inner Box (1,000 ea/Inner Box × 4 Inner Box=4,000 ea) RoHS Compliance Label AMOTECH Patent Pending - 17 - MAIN CHIP ANTENNA 5. Reliability Test No. Test Items Test Condition Requirement 1 High Temperature Exposure +85±3°C, 1000hrs 1. No visible defects. 2. Satisfy VSWR spec. 2 Temperature Cycling -40°C/30min ↔ +85°C/30min, 1000 Cycle 1. No visible defects. 2. Satisfy VSWR spec. 3 Biased Humidity - Humidity: 85%RH - Temperature: 85°C - Time: 1000Hrs 1. No visible defects. 2. Satisfy VSWR spec. 4 Mechanical Shock - Acceleration: 40㎨ - Duration Time: 11min - X.Y.Z each 3 times 1. No visible defects. 2. Satisfy VSWR spec. 5 Vibration - 5-55-5㎐, 1 Octave/min - Amp.=1.5mm,acceleration=2x9.8㎨(G) - Crossover Freq.=18㎐ 1. No visible defects. 2. Satisfy VSWR spec. 6 ESD - ESD Level: 8KV, - Mode: Contact discharge, 100 times 1. No visible defects. 2. Satisfy VSWR spec. 7 Adhesion Strength of Soldering - Used of push pull gauge 1. Spec (Min: 5Kgf) 8 Solderability - Dipping 250±5°C / 5 sec 1. No visible defects. 9 Board Flex - 2mm, Duration time: 1min - No open parts, No crack at soldering points 1. No visible defects. 2. Satisfy VSWR spec.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: HR/2019/1001602 Page: 1 of 7 Authorized Signature: Derek Yang Wireless Laboratory Manager Cover PRF Exposure Evaluation Report Application No.: HR/2019/10016 Applicant: Quectel Wireless Solutions Co., Ltd. Address of Applicant: 7th Floor, Hongye Building, No.1801 Hongmei Road, Xuhui District, Shanghai 200233, China Manufacturer: Quectel Wireless Solutions Co., Ltd. Address of Manufacturer: 7th Floor, Hongye Building, No.1801 Hongmei Road, Xuhui Distri…

Text truncated - open the document above for the full version.