2ARXKVHH10veeaHub

Installation Guide for VeeaHub™ Pro Outdoor Version 0.3 Veea, Inc. Confidential & Proprietary 1 Introduction The VeeaHub Pro Outdoor (VHH10) is a ruggedized version of the popular VeeaHub Pro intelligent wireless hub. The VHH10 has an IP-65 rating and is designed to be installed in outdoor environments. This document will be your guide to the proper installation of the VHH10. VHH10 Installation Kit The VHH10 installation kit is packed in a separate box from the VHH10 unit itself. The installation kit contains: • 1 x Wall Mounting Bracket (2 pieces) • M8 screws to attach mounting bracket to VHH10 • M8 screw to attach grounding cable • 2 x M12 male connectors with pigtail cables for ethernet • 1 x M12 female connector with pigtail cable for power • 1 x Self-locking tweezers (for SD card insertion) Understanding the VHH10 As you read through this document, please refer to the following diagrams to help you locate the various connections, buttons and Indicators: 1 2 3 4 5 6 7 Figure 1 1. Lower LED 2. Upper LED 3. Power Connector (M12 male) 4. Ethernet Connector (M12 female) – this connection supports PoE 5. Ethernet Connector (M12 female) Veea, Inc. Confidential & Proprietary 2 6. RS232/422/485 (M12 female) – for serial IoT connection 7. Reset button A B C Figure 2 A. LTE Primary Antenna B. Bluetooth Antenna C. LTE Diversity Antenna Understanding the Lights The lights (refer to Figure 1) are named as follows: 1. Lower – This light is the lower of the pair of lights on the side of the unit. 2. Upper – This light is the upper of the pair of lights on the side of the unit. Each of these lights are either off, on or flashing read, green or blue. The resulting pattern provides information about the state of the unit. The following table is a partial listing of the status patterns of the device indicator lights. State Lower Upper Normal Operation On Green On Green No Power Off Off Bootloader Starting On Green Off Linux Starting Off On Green Reset Flashing Red Off Recovery Flashing Red Flashing Red Table 1 In general, when a light is flashing red, some error condition exists. In that case, the specific pattern on the indicator lights will tell more details about the specific error. For a complete listing of all the error conditions and their associated light patterns please refer to the VHH10 User Guide document. Ethernet Ports The VHH10 unit has two ethernet ports. The port labeled #4 in Figure 1 above, accepts 802.3bt power and should be used as the primary gateway connection. The other ethernet port is an optional auxiliary Veea, Inc. Confidential & Proprietary 3 ethernet connection. Use the connectors provided in the installation kit to install the ethernet connection(s), as needed. Refer to Table 3 for the pinout information and cabling recommendations for each connection attaching to the lower edge of the VHH10 unit. Connector Pin Diagram Assignment AWG Twisted Pairs Power Pin1, V+, Red Pin3, V-, Black Pin4, GND, Green/Yellow 24# Pin 1&3 Ethernet/PoE P1, DA+, White/Orange P2, DA-, Orange P3, DB+, White/Green P4, DB-, Green P5, DD+, White/Brown P6, DD-, Brown P7, DC-, White/Blue P8, DC+, Blue 24# CAT5e Pin 1&2 Pin 3&4 Pin 5&6 Pin 7&8 RS232/422/485 Serial Pin1, RTS, White/Orange Pin2, CTS, White/Green Pin3, TXD, Orange Pin4, RXD, Green Pin5, GND, Brown 24# CAT5e Pin 1&3 Pin 2&4 Table 2 Veea, Inc. Confidential & Proprietary 4 For reference, Table 4 shows the pin assignments for the far end of the cables coming from the VHH10 unit. Connector Twisted Pairs Pin Assignments Ethernet/PoE RJ-45 Pin1, DA+, White/Orange Pin2, DA-, Orange Pin3, DB+, White/Green Pin4, DB-, Blue Pin5, DD+, White/Blue Pin6, DD-, Green Pin7, DC-, White/Brown Pin8, DC+, Brown Serial DB-9M Pin1, N/C Pin2, RXD, Green Pin3, TXD, Orange Pin4, N/C Pin5, GND, Brown Pin6, N/C Pin7, RTS, White/Orange Pin8, CTS, White/Green Pin9, N/C Table 3 Mounting the VHH10 The unit may be mounted either on a flat surface (such as a wall) or on a pole (refer to Fig. 3). The wall mount bracket is included in the installation kit. Note that this bracket consists of two pieces: one piece attaches to the VHH10 unit and the other piece gets mounted to the surface of the wall. IMPORTANT: You must ensure that the unit is mounted so that the edge with the antenna connections facing UP, as shown in Fig. 3. Also make sure to orient the wall mounting bracket correctly, as shown in the diagram. Veea, Inc. Confidential & Proprietary 5 Figure 3 Grounding Connection The VHH10 unit must be properly grounded to ensure reliable operation. The grounding connection (see Fig 4) must be securely and effectively connected to an actual earth ground. A grounding stake, grounded pole or similar grounded metal structure may be used. Figure 4, shows the back of the VHH10 unit with the unit piece of the wall mounting bracket attached. The location of the grounding connection is shown in that Figure by the large green arrow. Because it may be difficult to reach this connection after the unit is hung on the wall, it is advisable to connect the grounding lug to the VHH10 unit before hanging the unit on the wall mount. Veea, Inc. Confidential & Proprietary 6 Figure 4 Wall Mounting Procedure 1. Attach the unit piece of the wall mounting bracket to the back of the VHH10 unit with three M8 bolts, as shown in Figure 4. Please notice that a single bolt attaches in the middle at the top of the bracket and two bolts attach the bottom of the bracket. The holes in the top corner of the bracket are unused. 2. Attach the wall piece of the wall mounting bracket to the wall surface so that it is oriented as shown in Figure 5. The side rails must be away from the wall so that the unit lays flat on the wall. The locking flanges must be on the bottom as shown in this figure. 3. Attach the grounding cable to the grounding connection on the unit assembly, as described above. 4. Hang the unit assembly on the wall piece of the bracket by matching up the bracket side flanges and sliding the unit assem…

Text truncated - open the document above for the full version.

Supplier's Declaration of Conformity 47 CFR § 2.1077 Compliance Information Model Name As stated on agency label FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (3) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Responsible Party – U.S. Contact Information Veea Inc 164 E 83rd Street, New York NY, 10028 + 619-787-5225 https://www.veea.com/ (SIGNATURE / DATE) UL (In use for limited model: VHE09 series and VHE10 Series only) To reduce potential safety issues, only the AC adapter provided with the product, a replacement AC adapter provided by VEEA Inc., or an AC adapter purchased as an accessory from VEEA Inc., should be used with the product. This product is only to be connected to PoE networks without routing to outside plants. Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. Pour réduire les problèmes de sécurité potentiels, seul l’adaptateur secteur fourni avec le produit, un adaptateur secteur de remplacement fourni par VEEA Inc. ou un adaptateur secteur acheté en tant qu’accessoire auprès de VEEA Inc. doit être utilisé avec le produit. Ce produit doit uniquement être connecté à des réseaux PoE (alimentation intégrée) sans routage vers des réseaux extérieurs. Risque d’explosion si la pile est changée avec un type incorrect. Veuillez recycler les piles usages selon les Instructions. Federal Communications Commission NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 28cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. TD-LTE无线数据终端．VHE09L/VHE10L/ VHH10L 安装无线数据终端,将天线电缆移到旁边,插入4G LTE无线数据端卡,如图所示。 安装前示意图 安装后示意图 安装位置依机种不同而有所差异，多数使用者将型号VHE09L,VHE10L安装于室内(例如:卖场、办公室、餐 厅、学校)的使用环境，型号VHH10L则安装于户外的环境。 이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 E mail : sales.eaw@us. bureauveritas.com Product and Gertification Representative Authorl zatlon Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To lnitial Release (obsolete) 1.0 {.0Nov-l4-2006 Revised wording (obsolete) 1.02.0Sept-25-2047 Updated company template (obsolete) 2.03.0 Jan-31 -2012 Updated letter information (obsolete) 3.0 4.0May-23-2014 Added FCC lD field (obsolete) 4.05.0 Sep-l 6-2014 Updated company name & logo (current) 5.0 6.0 Jun-27-2018 SC9F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 6.0 Veea lnc. 164 E 83rd Street, NEW YORK, USA MinorOutlying lslands, 10028 Date: 112/2420 To: BVCPS, lNC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, Veea lnc, hereby authorize Bureau Veritas Consumer Product Services, lnc. to act as a Certification Body for certifying for the following project(s): FCC lD:2ARXKVHH10 Product Description: veeaHub Model: VHHl0XXX(X=A-Z, 0-9, blank or'r) Sincerely, M {u- Richard Kerr / SR VP Veea lnc. Tel: 619-787-5225 E-mail: rich@veea,com SCS-F18:Projectand ProductCertification RepresentativeAuthorization Letter Page2of 2 Rev6,0

Veea Inc. 164 E 83rd Street, NEWYORK, NY usA, 10028 Date: January 21 2020 Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Su bject: Request for Confi dentiality FCC ID:2ARXKVHH10 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR$$0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. O Schematic Diagram a Block Diagram a Operational Description o Software Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disolosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission' s policy, in order to comply with the marketing regulations in 47 CFR $2.803 and the importation rules in 47 CFR 52.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. a Extemal Photos a Internal Photos a Test SetupPhotos a Users Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, /-* Richard Kerr I SR VP Veea fnc. Tel: 619-787-5225 E-mail: [email protected]

Veea Inc. 164 E 83rd Street, NEW YORK, USA Minor Outlying Islands, 10028 Date: 2020-01 -02 FCC lD: 2ARXKVHH1O AUTHORITATION LETTER To Whom lt May Concern: Veea lnc. hereby authorizes Amanda Wu / Senior Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch ("BV CPS Taoyudr"), to act on its behatf in aLl matters retating to the Federal Communication Commission ("FCC") application for equipment authorization in connection with the FCC lD tisted above, inctuding signing of att documents retating to these matters. Any and alt acts carried out by Amanda Wu / Senior Specialist of BV CPS Taoyuan on Veea lnc.'s behalf, within the scope of the powers granted herein, shatl have the same effect as acts of its own. lf you have any questions regarding the authorization, ptease don't hesitate to contact us. Sincerety yours, M/r*_ Richard Kerr I SR VP Veea lnc. Tet: 619-787-5225 E-mai[: [email protected]

Veea Inc. 164 E 83rd Street, NEW YORK, USA Minor Outlying Islands, 10028 Professional Installation Attestation Date: 2020-01-14 FCC ID: 2ARXKVHH10 We, Veea Inc. hereby declare that requirements of KDB 353028 D01 Antennas Part 15 Transmitters v01 have been met and shown on the following questions. Further we declare that the info listed below are correct and represent the product in consideration under this filing. 1. Professional installation must be justified. Description: Device is outdoor Access Point and must need special trained professional in configuring and installing the product, more details please refer to user manual exhibit. 2. Professional installation does not permit use of any antenna with the transmitter; the permitted types of antenna specified as below. Description: Below listed of Antennas has been compliance FCC Rule Part 15 requirement, more details please refer to test reports. Ant. Type Connecter Antenna Gain (dBi) Frequency (GHz) Bluetooth Zigbee WLAN 2.4 5.150-5.850 PIFA 2.2 N/A N/A N/A Dipole N type 4.1 N/A N/A N/A CHIP 6 3.2 3.2 2.1 3. The applicant should address the following items when justifying professional installation. (1) To qualify for professional installation, please explain why the hardware is not readily available to average consumer. Description: Due to this product and will not be sold directly to the general public through retail store, therefore the hardware is not readily available to average consumer. Veea Inc. 164 E 83rd Street, NEW YORK, USA Minor Outlying Islands, 10028 (2) Marketing — Applicant must ensure device cannot be sold via retail to the general public or by mail order. Description: This product and will not be sold directly to the general public through retail store. It will be sold to authorized dealers or installers only. (3) Applicant must show that device intended use is not for consumers and general public. Description: Device is for industrial/commercial use. (4) Explain what is unique, sophisticated, complex, or specialized about the equipment that REQUIRES it to be installed by a professional installer? Description: Device is outdoor Access Point, which may be installed on a high place or on the exterior wall of a building, and must be installed by a professional installer. 4. Other professional installation requirements (1) Installation must be controlled. Description: The product will be distributed through controlled distribution channel which has special trained professional to install this product (2) Installed by licensed professionals. Description: Device sold to dealer who hires installers and need special trained professional in configuring and installing the product. (3) Installation requires special training. Description: The product need special programming, access to keypad, field strength measurements made, so must need special trained professional in configuring and installing the product. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! _____________________ Richard Kerr / SR VP Veea Inc. Tel: 619-787-5225 E-mail: [email protected]

Reference No.: 190918C14-3 Page No. 1 / 4 CONSTRUCTION PHOTOS OF EUT Reference No.: 190918C14-3 Page No. 2 / 4 Reference No.: 190918C14-3 Page No. 3 / 4 Reference No.: 190918C14-3 Page No. 4 / 4

Reference No.: 190918C14-1 Page No. 1 / 3 CONSTRUCTION PHOTOS OF EUT Reference No.: 190918C14-1 Page No. 2 / 3 Reference No.: 190918C14-1 Page No. 3 / 3

VHH10 Serial Number: XXXXXXXXXXXXXXXXXXXX MAC Number: XX:XX:XX:XX:XX:XX ID Number: XXXX-XXXX-XXXX-XXXX Model ・型号・ VHH10 FCC ID:2ARXKVHH10 Contains FCC ID:2ATM8EC25A R-C-Vee-VHH10 Manufactured date · 制造日期· 申请商 前海爱讯科技（深圳）有限公司 Country of Origin・生产地・ / Veea Inc/Taiwan/台湾制造 E352974 Input・输入・ 48V 1.35A TD-LTE无线数据终端

VHH10 Serial Number: XXXXXXXXXXXXXXXXXXXX MAC Number: XX:XX:XX:XX:XX:XX ID Number: XXXX-XXXX-XXXX-XXXX Model ・型号・ VHH10 FCC ID:2ARXKVHH10 Contains FCC ID:2ATM8EC25V R-C-Vee-VHH10 Manufactured date · 制造日期· 申请商 前海爱讯科技（深圳）有限公司 Country of Origin・生产地・ / Veea Inc/Taiwan/台湾制造 E352974 Input・输入・ 48V 1.35A TD-LTE无线数据终端

Reference No.: 190918C14-5 Page No. 1 / 18 CONSTRUCTION PHOTOS OF EUT 5G WiFi 5G WiFi 5G WiFi 5G WiFi 5G WiFi 5G WiFi 5G WiFi 2.4G WiFi 5G WiFi 2.4G WiFi BT Chip Zigbee Zigbee Reference No.: 190918C14-5 Page No. 2 / 18 Reference No.: 190918C14-5 Page No. 3 / 18 Reference No.: 190918C14-5 Page No. 4 / 18 Reference No.: 190918C14-5 Page No. 5 / 18 Reference No.: 190918C14-5 Page No. 6 / 18 Reference No.: 190918C14-5 Page No. 7 / 18 Reference No.: 190918C14-5 Page No. 8 / 18 Reference No.: 190918C14-5 Page No. 9 / 18 Reference No.: 190918C14-5 Page No. 10 / 18 Reference No.: 190918C14-5 Page No. 11 / 18 Reference No.: 190918C14-5 Page No. 12 / 18 Reference No.: 190918C14-5 Page No. 13 / 18 Reference No.: 190918C14-5 Page No. 14 / 18 Reference No.: 190918C14-5 Page No. 15 / 18 Reference No.: 190918C14-5 Page No. 16 / 18 Reference No.: 190918C14-5 Page No. 17 / 18 Reference No.: 190918C14-5 Page No. 18 / 18

Reference No.: 190918C14-2 Page No. 1 / 13 CONSTRUCTION PHOTOS OF EUT BT PIFA 5G WiFi 5G WiFi 2.4G WiFi 5G WiFi 5G WiFi 5G WiFi BT Chip 5G WiFi Zigbee Zigbee 5G WiFi 5G WiFi 2.4G WiFi Reference No.: 190918C14-2 Page No. 2 / 13 Reference No.: 190918C14-2 Page No. 3 / 13 Reference No.: 190918C14-2 Page No. 4 / 13 Reference No.: 190918C14-2 Page No. 5 / 13 Reference No.: 190918C14-2 Page No. 6 / 13 Reference No.: 190918C14-2 Page No. 7 / 13 Reference No.: 190918C14-2 Page No. 8 / 13 Reference No.: 190918C14-2 Page No. 9 / 13 Reference No.: 190918C14-2 Page No. 10 / 13 Reference No.: 190918C14-2 Page No. 11 / 13 Reference No.: 190918C14-2 Page No. 12 / 13 Reference No.: 190918C14-2 Page No. 13 / 13

Report No.: SA190918C14 Page No. 1 / 7 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA190918C14 FCC ID: 2ARXKVHH10 Contains module FCC ID: 2ATM8EC25A 2ATM8EC25V Test Model: VHH10 Series Model: VHH10XXX (X=A-Z, 0-9, blank or "-") Received Date: Sep. 18, 2019 Test Date: Oct. 29 ~ Nov. 29, 2019 Issued Date: Dec. 11, 2019 Applicant: Veea Inc Address: 164 E 83rd Street, New York NY, 10028, USA Applicant of Contained Module: Hawkeye Tech Co., Ltd. Address of Contained Module: 13F. No. 736, Zhongzheng Rd., Zhonghe Dist., New Taipei City 235, Ta i w a n Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Ta i w a n Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth ourfindings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA190918C14 Page No. 2 / 7 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 3 Calculation Result of Maximum Conducted Power ........................................................................... 6 Report No.: SA190918C14 Page No. 3 / 7 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA190918C14 Original release Dec. 11, 2019 Report No.: SA190918C14 Page No. 4 / 7 Report Format Version: 6.1.1 1 Certificate of Conformity Product: veeaHub Brand: Test Model: VHH10 Series Model: VHH10XXX (X=A-Z, 0-9, blank or "-") Sample Status: Engineering sample Applicant: Veea Inc Applicant of Contained Module: Hawkeye Tech Co., Ltd. Test Date: Oct. 29 ~ Nov. 29, 2019 Standards: FCC Part 2 (Section 2.1091) References Test Guidance: IEEE C95.3 -2002 KDB 447498 D01 General RF Exposure Guidance v06 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date:Dec. 11, 2019 Celine Chou / Senior Specialist Approved by : , Date:Dec. 11, 2019 Bruce Chen / Senior Project Engineer Report No.: SA190918C14 Page No. 5 / 7 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 28cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA190918C14 Page No. 6 / 7 Report Format Version: 6.1.1 3 Calculation Result of Maximum Conducted Power Frequency Band (MHz) Max Power (dBm) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) WLAN, CDD Mode 2412-2462 29.90 6.21 28 0.4145 1 5180-5240 18.78 8.12 28 0.0497 1 5745-5825 26.37 8.12 28 0.2854 1 WLAN, Beamforming Mode 5180-5240 12.76 8.12 28 0.0124 1 5745-5825 19.96 8.12 28 0.0652 1 Bluetooth LE 2402-2480 -5.02 6.00 28 0.0001 1 Bluetooth EDR 2402-2480 7.77 6.00 28 0.0024 1 Zigbee 2405-2475 19.18 3.20 28 0.0176 1 WWAN (module model: EC25-A) WCD…

Text truncated - open the document above for the full version.

Report No.: RF190918C14-4 Page No. 1 / 76 Report Format Version:6.1.2 FCC Test Report Report No.: RF190918C14-4 FCC ID: 2ARXKVHH10 Test Model: VHH10 Series Model: VHH10XXX (X=A-Z, 0-9, blank or "-") Received Date: Sep. 18, 2019 Test Date: Oct. 29 ~ Nov. 29, 2019 Issued Date: Dec. 11, 2019 Applicant: Veea Inc Address: 164 E 83rd Street, New York NY, 10028, USA Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF190918C14-4 Page No. 2 / 76 Report Format Version:6.1.2 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT ................................................................................................................ 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Duty Cycle of Test Signal .................................................................................................................. 12 3.4 Description of Support Units ............................................................................................................. 13 3.4.1 Configuration of System under Test .................................................................................................. 13 3.5 General Description of Applied Standards and References ............................................................. 13 4 Test Types and Results ...................................................................................................................... 15 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 15 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 15 4.1.2 Test Instruments ................................................................................................................................ 16 4.1.3 Test Procedures ...................................................…

Text truncated - open the document above for the full version.