2ASIN-994720SIFER NFC Card Reader by Inner Range

Inner Range SIFER Smart Card Reader. Installation Manual.Revision 4.0 April. 2020. Inner Range SIFER Smart Card Reader P/N: 994720 (Std) / 994720MF (Multi-format) Features -Suitable for narrow door frames or mullions. - Optical tamper device. - Configurable RGB LEDs and Beeper. - Multi-format version reads CSN or UID data from other 13.56MHz formats. See Data Sheet. - Connects to host Module via multi-drop RS485. - Firmware updates over system wiring in Inner Range systems. Latest firmware recommended. Non-metallic mounting surface recommended. See ‘Mounting Surface’ note on page 2. FCC (North America) This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: 1.This device may not cause interference; and 2.This device must accept any interference, including interference that may cause undesired operation of the device. Class B product: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off & on, the user is encourage to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help Warning: Any changes or modifications not expressively approved by Inner Range Pty Ltd could void the user's authority to operate this equipment ISED Canada L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1.L’appareil ne doit pas produire de brouillage; 2.L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. CAN ICES-3 (B)/NMB-3(B) Extending Cable See “Preliminary Installation Notes 3 & 4” on page 2. The pigtail cable can be extended with twisted-pair multistrand data cable. Pair 1 for Data A/B; Pair 2 for V+/0V. Shielded cable provides additional noise immunity. RS485/RS422 data cable, balanced data cable and multistrand UTP cable are recommended. Specific recommendations are provided below. READER POWER: Remember to allow for voltage drop on V+/ 0V over longer distances and/or when Readers are wired in a daisy chain (multi-drop) configuration. Supply voltage drop on the cable is approx. 17mV per metre per Reader using 7/0.2 (24AWG) cable and assuming each Reader draws 100mA. OVERALL SHIELD (2 Pair) Tycab. DPF4702 or DCK4702Belden. 9842 Electra. EAS7202P or EAS7302PGarland. MCP-2S General Cable. B2002CSAlpha. 6413 Roadworx. RW600224Olex. JD2PS485A OVERALL SHIELD (3 Pair) Belden. 9843Tycab. DPF6702 General Cable. B2003CSGarland. MCP-3S Electra. EAS7203PElectra. EAS7303P INDIVIDUALLY SHIELDED PAIRS (2 Pair) Tycab. DQQ47025Garland. MCP-2IS Alpha. 2466CBelden. 8723 UTP Garland UTPL5EMTP (4 Pair stranded UTP patch cable) If you have a requirement to use other cable types (e.g. short runs of non-twisted cable), please contact Inner Range Technical Support for advice. Parts List - Installation manual. (This document) - Reader body with integrated pigtail cable. - Mounting plate and Countersunk screw. Specifications Environment:Operating Temp: -35°C to +65°C. Ingress Protection: IP67 Physical dimensions.Height: 94 mmWidth: 40 mm Depth: 16 mm (26mm with Spacer) Mounting plate.91.5 mm (H) x 38 mm (W) Power supply input:11-14V DC <500mV ripple. Current consumption:75 - 100mA* typical. 150mA max. *Depends on LED configuration. V+/0V must only be connected to a power-limited circuit. Maximum Cabling Distance using recommended cables. Power (V+/0V). @100mA* per Reader. To 1 Reader using 2-Pair 7/0.2 cable: 100m. To 1 Reader using 2-Pair 14/0.2 cable: 200m. To 2 Readers using 3-Pair (2 pairs for +V/0V)100m. Data (Data A/Data B/0V). Access Module to furthest Reader:1000m. Total data cabling on one “RDR RS485” Port:1000m. For longer cable runs &/or multiple Readers on the same run. One of the following may be required: -Heavier duty 2-pair cable. -Additional pair or separate heavy duty fig. 8 for +V/0V. -A separate battery-backed local power supply. See “READER POWER” below for more details. Page 1 This manual is subject to change without notice. www.innerrange.com.au © 2014 - 2020. Inner Range Pty. Ltd.Doc. Part No: 634720 ytilibitapmoC tcudorPnoisreVeludoMrepsredaeRREFIS CAI/CSIretalro0.4V)YLNOCAI(61 MALIretalro0.2V61 MALSretalro0.2V4 erawtfoSitir getnIretalro0.4Va/n rellortnoCnoitpecnIretalro0.1Vro0.5.1Vebtsumeraw'fREFIS(8 )smetsySnoitpecnIniretal Optional Spacer for metallic surface P/N: 999033 UL Requirements (North America) Refer to the Inner Range host LAN Module Installation manual for details of UL regulatory requirements. Inner Range SIFER Smart Card Reader. Installation Manual.Revision 4.0 April. 2020. V+ 0V A B RedBlackWhiteGreenOrange Factory use only.Not used in the field. Preliminary Installation Notes 1. MOUNTING SURFACE. SIFER Readers should be installed on non-metallic surfaces. Mounting on a metallic surface is not recommended and will impair performance. In circumstances where installatio…

Text truncated - open the document above for the full version.

April 2020 The specifications and descriptions of products and services contained in this document were correct at the time of publishing. Inner Range reserves the right to change specifications or withdraw products without notice. 1 /IC 16/04/2020 Subject: Internal photos to be kept confidential; FCC ID:2ASIN-994720 (IC ID: 25850-994720) The Inner Range SIFER Reader 994720 is an IP67 rated weather proof NFC card reader, Designed for external outdoor use in harsh environments. During manufacturing the device’s Printed Circuit Board (PCB) is enlcosed into the external plastic shell, this is then completely filled with black liquid epoxy potting compound. The device is then baked inside an oven in order to harden the epoxy leaving only the 4 core RS-485 interface cable exposed. Therfore there is no possible way for the end user to open or dismantle the product in order to visually inspect or identify the PCB. In the event the device becomes faulty it is then simply disposed of. R&D Testing & Compliance Manager INNER RANGE Pty Ltd Place and Date of Issue: INNER RANGE Pty Ltd 1 Millennium Court, Knoxfield, Victoria, Australia 3180 Ph: +61 (0) 3 9780 4300 Fax: +61 (0) 3 9753 3499 www.innerrange.com

February 2020 The specifications and descriptions of products and services contained in this document were correct at the time of publishing. Inner Range reserves the right to change specifications or withdraw products without notice. 1 POA 26/02/2020 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: 2ASIN-994720 To Whom It May Concern: We, the undersigned, hereby authorize Chris Zombolas at EMC Technologies Pty Ltd to act on our behalf, to apply to the Federal Communications Commission for authorization of our equipment. Any and all acts carried out by Chris Zombolas on our behalf shall have the same effect as acts of our own. In addition, I authorize Mr. Chris Zombolas, Technical Director of EMC Technologies Pty Ltd to sign the Form 731. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, R&D Testing & Compliance Manager INNER RANGE Pty Ltd Place and Date of Issue: INNER RANGE Pty Ltd 1 Millennium Court, Knoxfield, Victoria, Australia 3180 Ph: +61 (0) 3 9780 4300 Fax: +61 (0) 3 9753 3499 www.innerrange.com

May 2020 The specifications and descriptions of products and services contained in this document were correct at the time of publishing. Inner Range reserves the right to change specifications or withdraw products without notice. 1 Request for Confidentiality 18/05/2020 Subject: Confidentiality Request regarding application for certification of; FCC ID:2ASIN-994720 Pursuant to FCC 47 CRF 0.457, 0.459 the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested: Exhibit: Short Term Permanent Block Diagrams Short Term External Photo’s Short Term Permanent Internal Photo’s Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photo’s Short Term Permanent User’s Manual INNER RANGE Pty Ltd has spent substantial effort in developing this high security NFC card reader product and it is one of the few of its kind in industry that uses an inhouse designed proprietary protocol with a unique hardware design. Having the subject information easily available to “the outside world” would negate the advantage of having developed such a high security product. May 2020 The specifications and descriptions of products and services contained in this document were correct at the time of publishing. Inner Range reserves the right to change specifications or withdraw products without notice. 2 Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be withheld from public review due to materials that contain trade secrets and proprietary information. Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify FCC in the event information regarding the product or the product is made available to the public. FCC will then release the documents listed above for public disclosure to FCC Public Notice DA 04-1705 June 15,2004. R&D Testing & Compliance Manager INNER RANGE Pty Ltd Place and Date of Issue: INNER RANGE Pty Ltd 1 Millennium Court, Knoxfield, Victoria, Australia 3180 Ph: +61 (0) 3 9780 4300 Fax: +61 (0) 3 9753 3499 www.innerrange.com

Page 1 of 4 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex A: External - EUT Photographs Inner Range Pty Ltd 994720_RevD SIFER RFID Reader REPORT: E1902-1136A-3 Annex A DATE: March, 2019 EMC Bayswater Test Report E1902-1136A-3 Annex A Page 2 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 EUT – External views 2 3 4 5 6 7 AE – Inception Controller 8 9 AE – RFID tag 10 EMC Bayswater Test Report E1902-1136A-3 Annex A Page 3 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E1902-1136A-3 Annex A Page 4 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9 Photograph 10

994720 9 9 6 0 0 2 7

Page 1 of 37 EMC Bayswater Pty Ltd EMC ENGINEERS & LABORATORIES 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 EMC COMPLIANCE REPORT Certification Test Report In accordance with: CFR47 FCC Part 15, Subpart C Inner Range Pty Ltd 994720_RevD SIFER RFID Reader REPORT: E1902-1136A-2 Rev1 DATE: May, 2020 This report replaces the previously issued report E1902-1136A-2. Please refer to section 2 of this report for details of any previously issued reports. Accreditation Number: 18553 Accredited for compliance with ISO/IEC 17025 The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing and calibration reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. EMC Bayswater Test Report E1902-1136A-2 Rev1 Page 2 of 37 Prepared & tested by: Approved by: 21/05/2020 10:42 Fabio D’Amico (EMC Test Engineer) Neville Liyanapatabendige (Manager) Date Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. Certificate of Compliance EMC Bayswater Test Report: E1902-1136A-2 Rev1 Issue Date: May, 2020 Test Sample(s): SIFER RFID Reader Model No: SIFER RFID Reader Serial No: None stated Part No: 994720_RevD FCC ID: 2ASIN-994720 Client Details: Mr Thomas Kowalczyk Inner Range Pty Ltd 1 Millennium Court Knoxfield, Victoria, 3180, Australia Phone No: 03 9780 4300 e-mail: [email protected] Test Specification: CFR47 FCC Part 15, Subpart C Results Summary: 15.203 – Antenna Requirement Complied 15.225 (a) - Field Strength within the band 13.553 - 13.567MHz Complied 15.225 (b) - Field Strength within the bands 13.410-13.553 MHz and 13.567-13.710 MHz Complied 15.225 (c) - Field Strength within the bands 13.110-13.410 MHz and 13.710-14.010 MHz Complied 15.225 (d) - Field Strength outside the band 13.110-14.010 MHz Complied 15.225 (e) - Frequency tolerance of the carrier signal Complied 15.215 (c) - 20dB Emission Bandwidth Complied Test Date(s): 11 th to the 20 th of February, 2019 Test House (Issued By) EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South Victoria, 3136 Australia FCC Accredited Test Firm Registration number: 527798 Phone No: +61 3 9761 5888 e-mail: [email protected] Fax No: +61 3 8761 6547 Web: www.emcbayswater.com.au This is to certify that the necessary measurements were made by EMC Bayswater Pty Ltd, and that the Inner Range Pty Ltd, 994720_RevD, SIFER RFID Reader (Serial No: None stated), has been tested in accordance with requirements contained in the appropriate commission regulations. EMC Bayswater Test Report E1902-1136A-2 Rev1 Page 3 of 37 Accreditation number: 18553. The results of the tests, calibrations and/or measurements included in this document are traceable to Australian/national standards. NATA is a signatory to the ILAC Mutual Recognition Arrangement for the mutual recognition of the equivalence of testing, calibration and inspection reports. This document may not be reproduced except in full without approval from EMC Bayswater, with the exception of the certificate on page 2. EMC Compliance Report for Inner Range Pty Ltd Contents 1. Introduction ..................................................................................................................................... 4 2. Test Report Revision History ......................................................................................................... 4 3. Report Information .......................................................................................................................... 4 4. Summary of Results ....................................................................................................................... 5 5. Product Sample, Configuration & Modifications ......................................................................... 6 5.1. EUT Description ........................................................................................................................ 6 5.2. Product description .................................................................................................................... 6 5.3. Support Equipment .................................................................................................................... 6 5.4. Product operating modes .......................................................................................................... 7 5.5. Product operating mode for testing ........................................................................................... 7 5.6. Configuration ............................................................................................................................. 7 5.1. Modifications ............................................................................................................................. 7 6. Test Facility & Equipment .............................................................................................................. 8 6.1. Test Facility ............................................................................................................................... 8 6.2. Test Equipment ......................................................................................................................... 8 7. Referenced Standards .................…

Text truncated - open the document above for the full version.

Page 1 of 4 EMC ENGINEERS & LABORATORIES EMC Bayswater Pty Ltd 18/88 Merrindale Drive Croydon South, Victoria, 3136, Australia Telephone: +61 3 9761 5888 Facsimile: +61 3 8761 6547 Email: [email protected] ABN: 49 112 221 333 Photograph Annex C: Test Configuration Photographs Inner Range Pty Ltd 994720_RevD SIFER RFID Reader REPORT: E1902-1136A-3 Annex C DATE: March, 2019 EMC Bayswater Test Report E1902-1136A-3 Annex C Page 2 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photographs Number Photograph Description 1 Radiated measurements – EUT X Orientation 2 Radiated measurements – EUT Y Orientation 3 Radiated measurements – EUT Z Orientation 4 Radiated measurements – 9kHz to 30MHz – X Antenna orientation 5 Radiated measurements – 9kHz to 30MHz – Y Antenna orientation 6 Radiated measurements – 9kHz to 30MHz – Z Antenna orientation 7 Radiated measurements – 30MHz to 1000MHz 8 Radiated measurements – 1GHz to 2GHz 9 Carrier Frequency Stability – Test configuration 10 EMC Bayswater Test Report E1902-1136A-3 Annex C Page 3 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 1 Photograph 2 Photograph 3 Photograph 4 Photograph 5 Photograph 6 EMC Bayswater Test Report E1902-1136A-3 Annex C Page 4 of 4 This document may not be reproduced, except in full, without written approval from EMC Bayswater Pty Ltd. Photograph 7 Photograph 8 Photograph 9 Photograph 10