2ASJH-RVTYR201SmartPressure Sensor

TEAMBMPRO.COM OWNER’S MANUAL ProSmart TEAM BMPRO .COM POWERING YOUR ADVENTURES With over 50 years’ experience in power solutions combined with manufacturing and design facilities in Melbourne, Australia, BMPRO are the leading experts in RV power and control management. Inspired by the great outdoors, we have created a range of rugged, smart and reliable products to power your adventures. Our range of batter y, power and RV management and control systems gives you peace of mind when you are on the road, so that you can relax in even the most far flung destinations, knowing you have control over your power needs. To learn more about the BMPRO range of products, please visit our website teambmpro.com 4 SAFETY PRECAUTIONS Please read the Safety Precautions before installing or using ProSmart. Be sure to observe all precautions without fail. Failure to observe these instructions properly may result in personal damage, or personal injur y which depending on the circumstances may be serious and cause loss of life. Only install the SmartSense gas cylinder/propane gas sensor as described in this manual. No field assembly is required. The sync process to the app on your smart display, as described below, should occur in an area clearly out of any explosive atmosphere. Once SmartSense is synced to your smart display, the device is “in service” and operating normally. Device will then operate continually until batter y is otherwise removed or changed. There is no “Power Off” mode from that point forward. Once in service, the device may then be moved, repositioned, or removed from the tank as needed, without any special instruction or changes to the device. SmartSense is not intended for repair or maintenance, other than changing the batter y per subsequent sections of this manual. Any modification of the SmartSense may result in an unsafe condition. SmartSense should be removed from tank and opened for batter y change, clearly away from any explosive atmosphere. Do not use SmartSense for any other application, other environment, or in any other manner than as stated in this manual. Any misuse may result in an unsafe condition. The operational temperature for the SmartSense ranges from 1ºC to 32ºC (33ºF to 90ºF). 5 6 CONTENTS SAFET Y PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . 4 ABOUT PROSMART . . . . . . . . . . . . . . . . . . . . . . . 8 PROSMART SYSTEM DIAGRAM . . . . . . . . . . . . . . . . . . 9 DESCRIPTION OF PARTS . . . . . . . . . . . . . . . . . . . . . 10 SMARTLINK . . . . . . . . . . . . . . . . . . . . . . . . . 10 MOUNTING THE SMARTLINK . . . . . . . . . . . . . . . . . . . 12 THE PROSMART APP . . . . . . . . . . . . . . . . . . . . . . 13 COMPATIBLE DEVICES . . . . . . . . . . . . . . . . . . . . . 13 USING THE PROSMART APP FOR THE FIRST TIME . . . . . . . . . . 13 HOME SCREEN . . . . . . . . . . . . . . . . . . . . . . . . 16 SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SMARTPRESSURE . . . . . . . . . . . . . . . . . . . . . . . 19 INSTALLING SMARTPRESSURE SENSORS . . . . . . . . . . . . . 19 PAIRING SMARTPRESSURE SENSORS. . . . . . . . . . . . . . . 20 SMARTPRESSURE PAIRING UNSUCCESSFUL . . . . . . . . . . . . 21 PRESSURE SIGNAL NOT DETECTED . . . . . . . . . . . . . . . 22 UNPAIRING SMARTPRESSURE SENSORS . . . . . . . . . . . . . 22 SMARTSENSE . . . . . . . . . . . . . . . . . . . . . . . . . 23 INSTALLING SMARTSENSE SENSORS . . . . . . . . . . . . . . . 23 PAIRING SMARTSENSE SENSORS . . . . . . . . . . . . . . . . 24 SMARTSENSE PAIRING UNSUCCESSFUL . . . . . . . . . . . . . 26 SENSOR READING NOT DETECTED . . . . . . . . . . . . . . . . 26 UNPAIRING SMARTSENSE SENSORS . . . . . . . . . . . . . . . 26 Designed by BMPRO, one of Australia’s leading power solution experts, the BMPRO product range is proudly designed and manufactured in Melbourne, Australia, and represent a high- quality product that will provide years of service. DISCL AIMER: BMPRO accepts no liability for any loss or damage which may occur from the improper or unsafe use of its products. Warranty is only valid if the unit has not been modified or misused by the customer. Copyright © 2021 MANUAL PART 036052 REV 1.0 7 SMARTTEMP . . . . . . . . . . . . . . . . . . . . . . . . . 27 PAIRING SMARTTEMP SENSORS . . . . . . . . . . . . . . . . . 27 SMARTTEMP PAIRING UNSUCCESSFUL . . . . . . . . . . . . . . 29 UNPAIRING SMARTTEMP SENSORS . . . . . . . . . . . . . . . 29 BATTERY REPL ACEMENT . . . . . . . . . . . . . . . . . . . . 30 REPL ACING SMARTPRESSURE SENSOR BATTERIES . . . . . . . . . 30 REPL ACING SMARTSENSE SENSOR BATTERIES . . . . . . . . . . 31 REPL ACING SMARTTEMP SENSOR BATTERIES . . . . . . . . . . . 31 SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . 32 FAQS AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . 32 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . 33 COMPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . 34 WARRANT Y TERMS AND CONDITIONS (AUSTRALIA) . . . . . . . . . 36 LIMITED WARRANT Y TERMS AND CONDITIONS (USA) . . . . . . . . . 37 8 ABOUT PROSMART ProSmart is a system that allows you to easily monitor water levels, gas levels, tyre pressure, temperatures and batter y charge while on your adventures, all from an easy-to-use app on your smartphone. Included in your ProSmart package is SmartLink, a powered node that you can easily install and pair to your phone, which allows you to view both your wired and wireless sensors through a Bluetooth connection. Along with SmartLink, you can connect your battery to the ProSmart system using the included batter y cable. The ProSmart can be used anywhere where you have a 12V power source - such as your RV, truck, boat or 4WD! Up to 40 SmartConnect Blueooth sensors can be paired to the SmartLink and displayed in the official BMPRO ProSmart App, giving you a wealth of information at your fingertips. Several SmartConnect Bluetooth sensors are included in your package, as well as a wired temperature…

Text truncated - open the document above for the full version.

SETEC BMPRO PTY LTD 19 Henderson Road, Knoxfield, Victoria 3180, Australia --------------------------------------------------------------------------------------------------------------------- Date: 2021-04-20 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2ASJH-RVTYR201 Confidentiality Request To whom it may concern, Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of the information accompanying this application as outlined below: ☒ Block Diagram ☐ Tune-Up Information ☒ Operational Description ☐ Security Information ☒ Schematics ☐ Software Defined Radio (SDR) Information ☐ Parts List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, SETEC BMPRO PTY LTD ------------------------------- (Cecilio Dimasacat) (Compliance Engineer)

SETEC BMPRO PTY LTD 19 Henderson Road, Knoxfield, Victoria 3180, Australia -------------------------------------------------------------------------------- (FCC ID：2ASJH-RVTYR201) POWER OF ATTORNEY DATE: 2021-04-20 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, SETEC BMPRO PTY LTD are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, SETEC BMPRO PTY LTD ------------------------------- (Cecilio Dimasacat) (Compliance Engineer)

Reference No.: WTX21X02013773W-1 Page 2 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Reference No.: WTX21X02013773W-1 Page 3 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EUT View 3 EUT View 4 Reference No.: WTX21X02013773W-1 Page 4 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EUT View 5 EUT View 6

Reference No.: WTX21X02013773W-1 Page 1 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2ASJH-RVTYR201 Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the device’s expected lifetime. Proposed Label Location on EUT FCC ID Label Location

Reference No.: WTX21X02013773W-1 Page 5 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View 1 EUT Housing and Board View 2 Reference No.: WTX21X02013773W-1 Page 6 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Solder Board-Component View 1 Solder Board-Component View 2 Reference No.: WTX21X02013773W-1 Page 7 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Solder Board-Component View 3 Antenna View

Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Page 1 of 25 TEST REPORT Reference No. .................... : WTX21X02013773W-1 FCC ID ................................ : 2ASJH-RVTYR201 Applicant ........................... : Setec BMPRO Pty Ltd. Address ............................. : 19 Henderson Rd, Knoxfield, Victoria 3180, Ausralia Product Name ................... : SmartPressure Sensor Test Model. ........................ : RVTYR201 Standards .......................... : FCC Part 15.249 Date of Receipt sample .... : Feb.26, 2021 Date of Test........................ : Feb.26, 2021 to Apr.14, 2021 Date of Issue ..................... : Apr.14, 2021 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Testing Group (Shenzhen) Co., Ltd. Address: 1/F., Room 101, Building 1, Hongwei Industrial Park, Liuxian 2nd Road, Block 70 Bao'an District, Shenzhen, Guangdong, China Tel.: +86-755-33663308 Fax.: +86-755-33663309 Tested by: Reviewed By: Approved & Authorized By: Mike Shi / Project Engineer Lion Cai / RF Manager Silin Chen / Manager Reference No.: WTX21X02013773W-1 Page 2 of 25 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn TABLE OF CONTENTS 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 TEST STANDARDS ................................................................................................................................................... 5 1.3 TEST METHODOLOGY ............................................................................................................................................. 5 1.4 TEST FACILITY ....................................................................................................................................................... 5 1.5 EUT SETUP AND TEST MODE ................................................................................................................................. 6 1.6 MEASUREMENT UNCERTAINTY .............................................................................................................................. 7 1.7 TEST EQUIPMENT LIST AND DETAILS ..................................................................................................................... 8 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 10 3. ANTENNA REQUIREMENTS .............................................................................................................................. 11 3.1 STANDARD APPLICABLE ....................................................................................................................................... 11 3.2 TEST RESULT........................................................................................................................................................ 11 4. RADIATED EMISSIONS ....................................................................................................................................... 12 4.1 STANDARD APPLICABLE ....................................................................................................................................... 12 4.2 TEST PROCEDURE ................................................................................................................................................. 12 4.3 CORRECTED AMPLITUDE & MARGIN CALCULATION ............................................................................................ 14 4.4 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 14 5. OUT OF BAND EMISSIONS ................................................................................................................................. 19 5.1 STANDARD APPLICABLE ....................................................................................................................................... 19 5.2 TEST PROCEDURE ................................................................................................................................................. 19 5.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 19 6. EMISSION BANDWIDTH ..................................................................................................................................... 22 6.1 STANDARD APPLICABLE ....................................................................................................................................... 22 6.2 TEST PROCEDURE ................................................................................................................................................. 22 6.3 SUMMARY OF TEST RESULTS/PLOTS .................................................................................................................... 22 7. CONDUCTED EMISSIONS .................................................................................................................................. 24 7.1 TEST PROCEDURE ................................................................................................................................................. 24 7.2 BASIC TEST SETUP BLOCK DIAGRAM ................................................................................................................... 24 7.3 TEST RECEIVER SETU…

Text truncated - open the document above for the full version.

Reference No.: WTX21X02013773W-1 Page 8 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn EXHIBIT 4 - TEST SETUP PHOTOGRAPHS Radiation Emission Test Setup (Below 30MHz) Radiation Emission Test Setup (30MHz to 1GHz) Reference No.: WTX21X02013773W-1 Page 9 of 9 Waltek Testing Group (Shenzhen) Co., Ltd. http://www.semtest.com.cn Radiation Emission Test Setup (1GHz to 18GHz) Radiation Emission Test Setup (Above 18GHz) ***** END OF REPORT *****