2AT6QTDC8300Touch Screen Controller

WIFI Channel 12 and 13 Declaration Letter Applicant Letterhead. WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for FCC ID:2AT6QTDC8300 Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels can’t be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note: 1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo-location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following: Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by-case basis Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: Yong-seong Park / Senior Director Signature: Phone: +82-2-6929-3161 Email: [email protected] Date: Aug. 19, 2019

Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 U.S. Agent Designation for Service of Process ATTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Universal Remote Control, Inc Contact Name: Lars Granoe Street Address: 500 Mamaroneck Ave, Suite 502, Harrison, NEW YORK City/Province/Zip: Harrison, NY 10528 Telephone No: 914-835-4484 Email: [email protected] FRN #: 0033571100 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: March 27, 2023 Signed by (Printed Name/Title): Lars Granoe / Vice President of Product Development *This letter must be dated within 1-year of the date the application is submitted to the TCB for device certification The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Summit Technology Grantee Code: 2AT6Q Contact Name: Yong-Seong Park Street Address: 130, Digital-ro, Namsung Plaza suite 611 City/Province/Zip: Geumcheon-gu, Seoul, 08589 Telephone No: +82-2-6929-3161 Email: [email protected] FRN #: 0028688497 Applicant Signature: Date: Mar. 27, 2023 Signed by (Printed Name/Title): Yong-Seong Park / Senior Director

Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 Date: Jun. 24, 2024 Timco Engineering, Inc. 13146 NW 86th Drive Suite 400 Alachua, FL 32615 SUBJECT: Declaration of digital portion for FCC ID: 2AT6QTDC8300 To Whom It May Concern: We, the undersigned, would like to declare that the digital portion catagorized as Other Class B digital devices & peripherals has been authorized under the Supplier's Declaration of Conformity (SDoC) procedures. Regards, __________________________________ Client’s name :Yong-seong Park Title : Senior Director Contact information : +82-2-6929-3161 Address : 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea)

Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 1 / 1 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 APPENDIX A : ATTESTATION STATEMENT Jun. 20, 2024 Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S.A. To whom it may concern: We, the undersigned, hereby authorize GUMI University EMC Center to act on our behalf in all matters relating to applications for equipment authorization, including the signing of all documents relation to these matters. Any and all acts carried out by GUMI University EMC Center on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to the application is subject of a denial of benefits, including FCC benefits, pursuant 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Sincerely, Yong-seong Park / Senior Director Summit Technology

Rev 1/26/2023 Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jun. 24, 2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AT6QTDC8300 Summit Technology (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, __________________________________ Client’s name :Yong-seong Park Title : Senior Director Contact information : +82-2-6929-3161 Address : 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea) Rev 1/26/2023 Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jun. 24, 2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AT6QTDC8300 Summit Technology (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, __________________________________ Client’s name :Yong-seong Park Title : Senior Director Contact information : +82-2-6929-3161 Address : 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea)

Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 Date: Jun. 24, 2024 Timco Engineering, Inc. 13146 NW 86th Drive Suite 400 Alachua, FL 32615 SUBJECT: Application for Certification for FCC: 2AT6QTDC8300 To Whom It May Concern: We, the undersigned, hereby authorize Hyun Kim at GUMI UNIVERSITY EMC CENTER on our behalf, to apply to FCC on our equipment. Any and all acts carried out by Hyun Kim on our behalf shall have the same effect as acts of our own. Regards, __________________________________ Client’s name :Yong-seong Park Title : Senior Director Contact information : +82-2-6929-3161 Address : 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea)

Confidentiality Request Letter Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 Jun. 24, 2024 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AT6QTDC8300 Pursuant to sections 0.457 and 0.459 of CFR 47, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application as: - Schematic Diagram - Block Diagram - Part List - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Client’s name :Yong-seong Park Title : Senior Director Contact information : +82-2-6929-3161 Address : 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Summit Technology 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea Tel: +82-2-6929-3161 Jun. 24, 2024 To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: 2AT6QTDC8300 To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47, and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 days; or for a specified date of / / not to exceed 180 days from the Grant Date. See KDB 726920. - User Manual - Test Setup Photos - External Photos - Internal Photos The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Client’s signature Client’s name :Yong-seong Park Title : Senior Director Contact information : +82-2-6929-3161 Address : 130, Digitial-ro, Namsung Plaza suite 611, Geumcheon-gu, Seoul, South Korea

Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 1 / 2 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 APPENDIX B : ID SAMPLE LABEL & LOCATION Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 2 / 2 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 LABELLING REQUIREMENTS The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase.  ID Label  ID Label Location of EUT ID Label

Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 1 / 11 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 APPENDIX L : RF EXPOSURE EVALUATION Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 2 / 11 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 1. RF Exposure Evaluation Test Result of RF Exposure Evaluation According to the KDB-447498 D01 V06, FCC 47CFR § 2.1093 the following RF exposure evaluation shall to demonstrate RF exposure compliance [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] *[√f(GHz)] 2.4 GHz Band (DTS) 802.11b Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 2412 7.6 8 ± 1 9 7.943 5 2.47 2437 7.8 8 ± 1 9 7.943 5 2.48 2462 7.3 8 ± 1 9 7.943 5 2.49 802.11g Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 2412 7.2 8 ± 1 9 7.943 5 2.47 2437 7.2 8 ± 1 9 7.943 5 2.48 2462 7.2 8 ± 1 9 7.943 5 2.49 802.11n(HT20) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 2412 7.5 8 ± 1 9 7.943 5 2.47 2437 7.7 8 ± 1 9 7.943 5 2.48 2462 6.9 8 ± 1 9 7.943 5 2.49 Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 3 / 11 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 802.11n(HT40) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 2422 6.9 8 ± 1 9 7.943 5 2.47 2442 7.7 8 ± 1 9 7.943 5 2.48 2462 6.8 8 ± 1 9 7.943 5 2.49 Worst case for each channel Frequency Max Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 2412 7.6 8 ± 1 9 7.943 5 2.47 2437 7.8 8 ± 1 9 7.943 5 2.48 2462 7.3 8 ± 1 9 7.943 5 2.49 The Max RF exposure is 2.49 Threshold at which no SAR required is << 3 for 1-g SAR, Separation distance is 5 mm Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 4 / 11 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 5 GHz Band (UNII 1) 802.11a Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5180 5.4 5 ± 1 6 3.981 5 1.81 5200 4.5 5 ± 1 6 3.981 5 1.82 5240 4.7 5 ± 1 6 3.981 5 1.82 802.11n(HT20) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5180 4.4 4 ± 1 5 3.162 5 1.44 5200 3.7 4 ± 1 5 3.162 5 1.44 5240 3.7 4 ± 1 5 3.162 5 1.45 802.11ac(VHT20) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5180 3.2 4 ± 1 5 3.162 5 1.44 5200 4.5 5 ± 1 6 3.981 5 1.82 5240 4.9 5 ± 1 6 3.981 5 1.82 802.11n(HT40) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5190 4.8 5 ± 1 6 3.981 5 1.81 5230 6.5 6 ± 1 7 5.012 5 2.29 802.11ac(VHT40) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5190 3.6 4 ± 1 5 3.162 5 1.45 5230 5.5 5 ± 1 6 3.981 5 1.82 Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 5 / 11 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 802.11ac(VHT80) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5210 4.1 5 ± 1 6 3.981 5 1.82 Worst case for each channel Frequency Max Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5180 5.4 5 ± 1 6 3.981 5 1.81 5190 4.8 5 ± 1 6 3.981 5 1.81 5200 4.5 5 ± 1 6 3.981 5 1.82 5210 4.1 5 ± 1 6 3.981 5 1.82 5230 6.5 6 ± 1 7 5.012 5 2.29 5240 4.9 5 ± 1 6 3.981 5 1.82 The Max RF exposure is 2.29 Threshold at which no SAR required is << 3 for 1-g SAR, Separation distance is 5 mm Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 6 / 11 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 5 GHz Band (UNII 2A) 802.11a Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5260 4.9 5 ± 1 6 3.981 5 1.83 5300 5.2 5 ± 1 6 3.981 5 1.83 5320 4.7 5 ± 1 6 3.981 5 1.84 802.11n(HT20) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5260 4.1 4 ± 1 5 3.162 5 1.45 5300 3.8 4 ± 1 5 3.162 5 1.46 5320 3.9 4 ± 1 5 3.162 5 1.46 802.11ac(VHT20) Frequency Average Conducted Output Power(dBm) Target Power /tolerance (dBm) Max tune up power Tolerance (dBm) Maximum Average Output Power(mW) Separation Destance (mm) RF Exposure 5260 2.8 3 ± 1 4 2.512 5 1.15 5300 5.2 5 ± 1 6 3.981 5 1.83 5320 5.2 5 ± 1 6 3.981 5 1.84 802.11n(HT40) Frequency Average…

Text truncated - open the document above for the full version.

GETEC-QP-16-008 (Rev.01) EMC CENTER This test report only contains the result of a specific sample supplied by applicant for the testing. It is not allowed to copy this report even partly without the approval of EMC center GUMI UNIVERSITY EMC CENTER Page 1 of 52 E E V V A A L L U U A A T T I I O O N N R R E E P P O O R R T T f f o o r r C C e e r r t t i i f f i i c c a a t t i i o o n n Rule Part(s) : FCC Part 15 Subpart C-Intentional Radiator § 15.247 Test Method : ANSI C63.10 (2020) Equipment Class : Digital Transmission System(DTS) EUT Type : Touch Screen Controller Type of Authority : Certification Model Name : TDC-8300 This equipment has been shown to be in compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10 (2020) I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the vest of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Tested by, Reviewed by, Jong-Woo, Park, Senior Engineer Hyun Kim, Technical Manager GUMI UNIVERSITY EMC CENTER GUMI UNIVERSITY EMC CENTER M M a a n n u u f f a a c c t t u u r r e e r r : : S S - - T T e e c c h h W W o o n n I I n n c c . . D D a a t t e e o o f f I I s s s s u u e e : : J J u u n n . . 2 2 0 0 , , 2 2 0 0 2 2 4 4 S S a a n n g g g g a a d d o o n n g g - - 3 3 0 0 3 3 , , 4 4 2 2 3 3 , , S S a a n n h h o o - - d d a a e e r r o o , , G G u u m m i i - - s s i i , , O O r r d d e e r r N N u u m m b b e e r r : : G G E E T T E E C C - - C C 1 1 - - 2 2 4 4 - - 2 2 2 2 9 9 G G y y e e o o n n g g s s a a n n g g b b u u k k - - d d o o , , R R e e p p u u b b l l i i c c o o f f K K o o r r e e a a T T e e s s t t R R e e p p o o r r t t N N u u m m b b e e r r : : G G E E T T E E C C - - E E 3 3 - - 2 2 4 4 - - 0 0 6 6 8 8 A A t t t t n n : : M M r r . . S S a a n n g g - - T T a a e e K K i i m m / / C C E E O O T T e e s s t t S S i i t t e e : : G G U U M M I I U U N N I I V V E E R R S S I I T T Y Y E E M M C C C C E E N N T T E E R R C C A A B B D D e e s s i i g g n n a a t t i i o o n n N N u u m m b b e e r r : : K K R R 0 0 0 0 3 3 3 3 A A P P P P L L I I C C A A N N T T : : S S u u m m m m i i t t T T e e c c h h n n o o l l o o g g y y A A D D D D R R E E S S S S : : 1 1 3 3 0 0 , , D D i i g g i i t t i i a a l l - - r r o o , , N N a a m m s s u u n n g g P P l l a a z z a a s s u u i i t t e e 6 6 1 1 1 1 , , G G e e u u m m c c h h e e o o n n - - g g u u , , S S e e o o u u l l , , S S o o u u t t h h K K o o r r e e a a C C O O N N T T A A C C T T P P E E R R S S O O N N : : M M r r . . Y Y o o n n g g - - s s e e o o n n g g P P a a r r k k / / S S e e n n i i o o r r D D i i r r e e c c t t o o r r e032a0d149014106a705542c9d6fa2f2 Order Number : GETEC-C1-24-229 FCC Part 15 Subpart C Test Report Number : GETEC-E3-24-068 Page 2 / 52 GETEC-QP-16-008 (Rev.01) EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 Version Test Report No. Date Description GETEC-E3-24-068 Jun. 20, 2024 - First Approval Report Order Number : GETEC-C1-24-229 FCC Part 15 Subpart C Test Report Number : GETEC-E3-24-068 Page 3 / 52 GETEC-QP-16-008 (Rev.01) EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................... 5 2. INTRODUCTION ........................................................................................................................................................ 6 3. PRODUCT INFORMATION ...................................................................................................................................... 7 3.1 DESCRIPTION OF EUT .............................................................................................................................................. 7 3.2 DEFINITION OF MODELS ........................................................................................................................................... 7 3.3 SUPPORT EQUIPMENT / CABLES USED ..................................................................................................................... 8 3.4 MODIFICATION ITEM(S) ........................................................................................................................................... 8 4. ANTENNA REQUIREMENT - §15.203 ..................................................................................................................... 9 4.1 DESCRIPTION OF ANTENNA ...................................................................................................................................... 9 5. DESCRIPTION OF TESTS ......................................................................................................................................... 9 5.1 TEST CONDITION ...................................................................................................................................................... 9 6. REFERENCES STANDARDS .................................................................................................................................... 9 7. SUMMARY OF TEST RESULTS ............................................................................................................................. 10 8. 6 DB BANDWIDTH MEASUREMENT .................................................................................................................. 11 8.1 OPERATING ENVIRONMENT.................................................................................................................................... 11 8.2 TEST SET-UP (LAYOUT) ..................................................................................................................…

Text truncated - open the document above for the full version.

Order Number : GETEC-C1-24-229 FCC Part 15 subpart C & FCC Part 15 subpart E Test Report Number : GETEC-E3-24-068 Page 1 / 1 EUT Type: Touch Screen Controller FCC ID.: 2AT6QTDC8300 APPENDIX J : ANTENNA SPECIFICATION http:// www.mobinus.com 대 외 비 CONFIDENTIAL •Antenna & matching •Smith Chart & VSWR Smith chart VSWR •Antenna & matching Ant MFWD-J5-AB Matching value Z0 Z1 Z2 Z0 Z2 Z1 2.Test Result http:// www.mobinus.com 대 외 비 CONFIDENTIAL •Passive Efficiency 2.Test Result http:// www.mobinus.com 대 외 비 CONFIDENTIAL •Radiation Pattern 2. Test Result 2.44GHz 5.49GHz