2ATM6-FST433Active RFID security tag operating in the 433 MHz band

Fortecho FST433 User Manual Document Reference: FST433 Manual V1.1 Date: 06 th February 2020 1 Overview 3 FT-XXX Usage 4 Technical Specification 4 Contact Details 4 Fitting Instructions 4 Installation 4 Maintenance 5 Cleaning 5 End of Life 5 Environmental 5 FCC Statement 5 FCC WARNING 5 NOTE: 5 Fortecho FST433 User Manual Page 3 of 5 1 Overview The document provides the specification and installation detail for the Fortecho FST433 tag range, FST433 Is the tag type the FT-XXX describes the tag model :- • FT-TGP • FT-TGPS • FT-TGAI Fortecho FST433 User Manual Page 4 of 5 FT-XXX Usage The FT-XXX Tag is a sealed Industrial tag that can be used for tagging indoor assets. The tags are supplied with a either a plastic wallet or an adhesive pad allowing them to be adhered to flat surfaces. Typical applications are for the security monitoring of artwork and high value assets. Technical Specification The FT-XXX tag range operate in the ISM, license free radio band and can be supplied from Fortecho as either 433MHZ or 868MHz devices. These bands are not globally free and there are restrictions on their use in some regions please contact Fortecho or a representative to ensure compliance in your chosen region. Contact Details Fortecho can be contacted on the details below. Matthew Bignell Systems Engineer Solon House 40A Peterborough Road London SW6 3BN Tel: +44 20 7736 3330 DDI: +44 20 7736 8934 Mob: +44 7425 885 474 Web: www.fortecho.com Fitting Instructions Requirements ▪ FT-XXX Tag ▪ Wallet or adhesive pad ▪ Dry Cloth Installation First ensure that the mounting surface is clean and free from debris, remove any dirt using the cloth. Using either the wallet or the adhesive pad, adhere the tag to the asset. The FT-XXX tag should not be installed at a height above 2m from the floor Fortecho FST433 User Manual Page 5 of 5 Maintenance The FT-XXX Tag is a sealed unit and requires no maintenance during its life span. Cleaning The FT-XXX Tag can be cleaned using water applied to a cloth. Solvents and Oils should not be used for cleaning the FT-XXX Tag End of Life At the end of its functional life the tag must be disposed of in a suitable local recycling facility and in accordance with any local laws pertaining to the recycling of waste electronic equipment. The tag consists of an ABS plastic clip housing, electronic components and a lithium battery. The tag contains no substances banned by the European Union’s Restriction of Hazardous Substances (RoHS) directive. Environmental The FT-XXX Tag has an operational temperature range of -20 to +55 Degrees Celsius. FCC Statement This device complies with Part 15 of FCC Rules and standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for an Intentional radiator, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Date 18/02/2020 TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Confidentiality Request FCC ID: 2ATM6-FST433 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commission’s Rules, Fortecho Solutions Ltd hereby requests permanent confidential treatment of information accompanying this application as outlined below: Schematics Bill of Materials Block Diagram The Applicate believes that publishing the above listed detail would provide their competitors with significant advantage substantially harming both the competitive nature of their product and their financial investment it its creation. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely, Name Dr. Mark Winsall Position : CTO Fortecho Solutions Limited UK Telephone Number: +44 20 7736 3330 Email: [email protected] www.fortecho.com

The FST433 range has a number of SKU’s all of which use the same PCBA, different formats are achieved by using different battery sizes and housing. Front Views FT-TGP FT-TGPS FT-TGAI Back Views FT-TGP FT-TGPS FT-TGAI

FST433 Labelling Detail Label is applied to back of product

The FST433 range has a number of SKU’s all of which use the same PCBA, different formats are achieved by using different battery sizes and housing. Front Views FT-TGP FT-TGPS FT-TGAI Back View FT-TGAI

FST433 Operational Detail The following is the description for the FT-TGAI Model The FT-TGAI Tag is an active tag that continuously transmits a unique ID number, which can be detected by the FS1000 reader. The tag includes a 3 Axial accelerometer with 15 pre-set levels of sensitivity. It can be configured to provide a motion alarm on movement. The FT-TGAI uses a high-quality single circuit board digital Temperature, Relative Humidity and Ambient Light sensors. The sensors are calibrated at manufacture and due to its single board integrated nature does not require recalibration when kept in a clean environment. The tag includes the facility for decontaminating the sensors in the unlikely event that contamination occurs. An internal battery powers the tag and the patented ultra-low power use design ensures longer battery life at higher rates of transmission than any other brand of active RFID tag. Various pre- set transmission intervals are available. Features • Measures Ambient Light, Temperature and Relative Humidity with a high-quality calibration- free digital sensor • Programmable Tag ID, Repetition Rate, RF Power Level, Site or Customer ID • Wireless transmission on a 30 second interval: Motion, Anti-Tamper, Battery Voltage, Ambient Light and T-rH measurements. • The FT-TGAI Tag is equipped with an anti-tamper switch which, when used in conjunction with Fortecho rare-earth tamper contacts, will send an alarm on removal from an asset. Typical Applications The FT-TGAI Tag is ideally suited for protecting 3D objects and high value assets in display cases. Optimum read range is achieved on metal with a 10% reduction on non-metals.

DATA SHEET WIRELESS COMPONENTS FR4 Chip Antenna ANT1204F002R0433A 433MHZ 1204 Series Product S pecification – August 18, 2014 V.0 www.ya geo.co m Aug. 18, 2014 V0 WIRELESS COMPONENTS 2 2 Product specification Ceramic Chip Antenna FEATURES  Compact size  Omni-directional Radiation  Tape & reel automaic mounting  Reflow process compatible  RoHS compliant APPLICATIONS  Smart meter  Industrial remote control  ISM band equipment ORDERING INFORMATION All part numbers are identified by the series, packing type, material, size, antenna type, working frequency and packing quantity. PART NUMBER ANT 1204 F 002 R 0433A (1) (2) (3) (4) (5) (6) ( 1 ) PRODUCT ANT = Antenna ( 2 ) SIZE 1204=12× 4 ( 3 ) ANTENNA TYPE L, F, A=Chip antenna ( 4 ) SERIAL NO. 002 ( 5 ) PACKING STYLE R = Tape and Reel ( 6 ) WORKING FREQUENCY 0433=433 MHz PHYCOMP CTC CAN4311059020431K 12NC 431105902043 www.ya geo.co m Aug. 18, 2014 V0 WIRELESS COMPONENTS 3 3 Product specification Ceramic Chip Antenna SPECIFICATION DESCRIPTION VALUE Centre Frequency 433 M Hz Bandwidth 28M Hz ( Typ. ) Return Loss 6.5 dB min Polarization Linear Azimuth Beamwidth Omni-directional Peak Gain 0.79 dBi ( Typ. ) Impedance 50 Ω Operating Temperature - 40~105 °C Maximum Power 1 W Termination Cu / Au (Environmentally-Friendly Leadless) Resistance to Soldering Heats 260°C , 10sec. NOTE 1. The specification is defined on Yageo evaluation board Table 1 O O U U T T L L I I N N E E S S Fig. 1 Antenna outlines DIMENSIONS DIMENSION L (mm) 12.30 ± 0.20 W (mm) 4.00 ± 0.20 T (mm) 1.60 ± 0.20 A (mm) 0.50 ±0.20 Table 2 Machinical Dimension TERMINAL NAME FUNCTION S1 Feeding Point S2 Soldering Point Table 3 Termination configuration www.ya geo.co m Aug. 18, 2014 V0 WIRELESS COMPONENTS 4 4 Product specification Ceramic Chip Antenna Fig. 3 Outlook and dimension of evaluation board REFERENCE DESIGN OF EVALUATION BOARD Fig. 4 Details of soldering Pad www.ya geo.co m Aug. 18, 2014 V0 WIRELESS COMPONENTS 5 5 Product specification Ceramic Chip Antenna Fig. 5 Return loss Fig. 6 Radiation pattern Frequency= 433 MHz Max gain = 0.79 dBi, at (150,330) MEG (mean effective gain)= -4.84 dBi Directivity (dB) = 6.35 Efficiency = -5.56dB, 27.79 % ELECTRICAL PERFORMANCES Evaluation board and XYZ direction Marker data 1. 419MHz, -6.5dB 2. 433MHz, -16dB 3. 447MHz, -6.5dB www.ya geo.co m Aug. 18, 2014 V0 WIRELESS COMPONENTS 6 6 Product specification Ceramic Chip Antenna REVISION HISTORY REVISION DATE CHANGE NOTIFICATION DESCRIPTION Version 0 Aug. 05, 2013 - - New data sheet for SMD type antenna, 433MHz application, 1204 series

TÜV SÜD, Octagon House, Concorde Way, Segensworth North, Fareham, Hampshire, United Kingdom, PO15 5RL Tel: +44 (0) 1489 558100 Website: www.tuv-sud.co.uk COMMERCIAL-IN-CONFIDENCE SAR EXCLUSION DOCUMENT Approved by Date 26 November 2019 Jonathan Kenny Authorised Signatory ©2019 Not to be reproduced, except in its entirety, without the permission of TÜV SÜD Page 1 of 2 Document 75945973-10 Issue 01 Fortecho RFID Tag 433MHz Transmitter Version: FCC Standalone SAR Test Exclusion Considerations (KDB 447498 D01 v06) Section 4.3.1 a) 100 MHz – 6 GHz – Separation Distance ≤50 mm The 1g SAR Test exclusion thresholds for 100 MHz to 6 GHz test separation distances ≤ 50 mm are determined by: [(max power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] [√f (GHz)] ≤ 3.0 for 1g SAR and ≤ 7.5 for 10g extremity SAR. • f (GHz) is the RF channel transmit frequency in GHz. • Power and distance are rounded to the nearest mW and mm before calculation. • The result is rounded to one decimal place for comparison • When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied. SAR Exclusion Result: Frequency (GHz) Power Output mW Duty Cycle % Maximum Power (Tune up Value) * (mW) Test Separation Distance (mm) SAR Test Exclusion Threshold Limit** SAR Test Exclusion (Yes/No) 0.43305 10 100 10 10 0.7 3.0 Yes 0.43479 10 100 10 10 0.7 3.0 Yes * Maximum power including tolerance of the time averaged declared conducted output power of the device. ** Select ≤ 3.0 for 1g SAR and ≤ 7.5 for 10g extremity SAR. The SAR exclusion threshold has been evaluated using the formula described above from information supplied by the manufacturer below. Based on the calculation above, the EUT is categorically excluded from SAR testing. ©2019 Not to be reproduced, except in its entirety, without the permission of TÜV SÜD Page 2 of 2 Document Number: 75945973-10 | Issue: 01 COMMERCIAL-IN-CONFIDENCE Manufacturer’s Declaration of Product Information: Equipment Description Technical Description: (Please provide a brief description of the intended use of the equipment) Fortecho RFID Tag 433MHz Manufacturer: Fortecho Solutions Ltd Model: FST-433 Part Number: PC-0048-003-03-Cx If more than one frequency band is supported, please confirm which combinations of bands are capable of Simultaneous Transmit. None – single band only Frequency Band 1: ISM Antenna length: Internal 1.4 cm Bottom frequency: 433.05 MHz Middle frequency: 433.92 MHz Top frequency: 434.790 MHz Maximum power (input to the antenna including a tolerance): 10m W Antenna gain (or maximum gain allowed): 2 dBi Separation distance from antenna to the user/bystander: 1 Cm Transmitter Duty Cycle: 100 % Note: the maximum time averaged conducted output power shown in the low power exclusion result is given by: P EIRP = P o x Duty Factor P EIRP = 10 mW x 1 = 10 mW Where: P o = 10 mW Duty factor = 100%/100 = 1

TÜV SÜD is a trading name of TUV SUD Ltd Registered in Scotland at East Kilbride, Glasgow G75 0QF, United Kingdom Registered number: SC215164 TUV SUD Ltd is a TÜV SÜD Group Company Phone: +44 (0) 1489 558100 Fax: +44 (0) 1489 558101 www.tuv-sud.co.uk TÜV SÜD Octagon House Concorde Way Fareham Hampshire PO15 5RL United Kingdom TÜV SÜD SIGNATURE NAME JOB TITLE RESPONSIBLE FOR ISSUE DATE Simon Bennett Innovations Manager Authorised Signatory 30 April 2020 Signatures in this approval box have checked this document in line with the requirements of TÜV SÜD document control rules. ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC 47 CFR Part 15C. The sample tested was found to comply with the requirements defined in the applied rules. SIGNATURE NAME JOB TITLE RESPONSIBLE FOR ISSUE DATE Graeme Lawler Test Engineer Testing 30 April 2020 Nandhini Mathivanan Test Engineer Testing 30 April 2020 FCC Accreditation 90987 Octagon House, Fareham Test Laboratory EXECUTIVE SUMMARY A sample of this product was tested and found to be compliant with FCC 47 CFR Part 15C: 2018 for the tests detailed in section 1.3. Report on the FCC Testing of: Fortecho Solutions Ltd 433 MHz RFiD Reader, Model: FS-1000-433 433 MHz Tag, Model: FST433 In accordance with FCC 47 CFR Part 15C Prepared for: Fortecho Solutions Ltd Solon House, 40A Peterborough Road London, SW6 3BN UNITED KINGDOM FCC ID: 2ATM6-FS1000 (Reader) and 2ATM6-FST433 (Tag) COMMERCIAL-IN-CONFIDENCE Document Number: 75945973-04 | Issue: 02 DISCLAIMER AND COPYRIGHT This non-binding report has been prepared by TÜV SÜD with all reasonable skill and care. The document is confidential to the potential Client and TÜV SÜD. No part of this document may be reproduced without the prior written approval of TÜV SÜD. © 2020 TÜV SÜD. This report relates only to the actual item/items tested. ACCREDITATION Our UKAS Accreditation does not cover opinions and interpretations and any expressed are outside the scope of our UKAS Accreditation. Results of tests not covered by our UKAS Accreditation Schedule are marked NUA (Not UKAS Accredited). Document Number: 75945973-04 | Issue: 02 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 1 of 32 Contents 1 Report Summary .........................................................................................................................2 1.1 Report Modification Record ...........................................................................................................2 1.2 Introduction ....................................................................................................................................2 1.3 Brief Summary of Results .............................................................................................................3 1.4 Application Form ...........................................................................................................................4 1.5 Product Information .......................................................................................................................8 1.6 Deviations from the Standard ........................................................................................................8 1.7 EUT Modification Record ..............................................................................................................8 1.8 Test Location .................................................................................................................................8 2 Test Details ..................................................................................................................................9 2.1 Manually Activated Transmitter .....................................................................................................9 2.2 Field Strength of Emissions ....................................................................................................... 10 2.3 20 dB Bandwidth ........................................................................................................................ 26 3 Photographs ............................................................................................................................. 28 3.1 Test Setup Photographs ............................................................................................................ 28 4 Measurement Uncertainty ....................................................................................................... 32 Document Number: 75945973-04 | Issue: 02 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 2 of 32 1 Report Summary 1.1 Report Modification Record Alterations and additions to this report will be issued to the holders of each copy in the form of a complete document. Issue Description of Change Date of Issue 1 First Issue 27 November 2019 2 Amendment to error in table 2. Update to section 2.1 30 April 2020 Table 1 1.2 Introduction Applicant Fortecho Solutions Ltd Manufacturer Fortecho Solutions Ltd Model Number(s) 433 MHz RFiD Reader, Model: FS-1000-433 433 MHz Tag, Model: FST433 Serial Number(s) Reader: 0048-003-097 Tag: Not Serialised (75945973-TSR0041) Tag: Not Serialised (75945973-TSR0051) Hardware Version(s) Reader: HW-03 Tag: PC-0048-003-03-XX Software Version(s) Reader: 1.74 Tag: 0.044 Number of Samples Tested 1 reader and 2 tags Test Specification/Issue/Date FCC 47 CFR Part 15C: 2018 Order Number Date 0429 01-May-2019 Date of Receipt of EUT 10-June-2019 and 25-July-2019 Start of Test 09-July-2019 Finish of Test 13-August-2019 Name of Engineer(s) Graeme Lawler and Nandhini Mathivanan Related Document(s) ANSI C63.10: 2013 Document Number: 75945973-04 | Issue: 02 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE Page 3 of 32 1.3 Brief Summary of Results A brief summary of the tests carried out in accordance with FCC 47…

Text truncated - open the document above for the full version.

1 Photographs 1.1 Test Setup Photographs Figure 1 – 30 MHz to 1 GHz (Tag) Figure 2 – 1 GHz to 5 GHz (Tag) Figure 3 – 30 MHz to 5 GHz (Reader) Figure 4 – 1 GHz to 5 GHz (Reader)