2ATPS-G18EB3D VR VIRTUAL REALITY GLASSES

FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. * RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2ATPS-G18EB G18EB, G18, G18E, G18EA, E06, E06EB We hereby acknowledge as follows: i. both signees confirm that the point of contact accepts responsibility to act as a US- American Representative on behalf of the applicant ii. the point of contact provides the physical U.S. address and email as listed below iii. both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. iv. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. US-American Point of Contact Applicant/Approval Holder Signature Date: 2026-1-7 Signature Date: 2026-1-7 Company Name: GLOCERTS TECHNOLOGY INC Dongguan Shinecon Industrial Co., Ltd FRN: 0036339737 0028581742 Contact Name: Huiying Fan Keqiang Yang Address: 19784 SUNKISSED RIDGE DR, RIVERSIDE, CA 92507 NO.9 SHIBEI ROAD TANGLI DISTRICT, FENGGANG DONGGUAN, China Phone: (626) 588-8039 13528577662 Email: [email protected] [email protected]

Page 1 of 2 FCC ID: 2ATPS-G18EB External Photos Page 2 of 2 FCC ID: 2ATPS-G18EB

Label FCC ID: 2ATPS-G18EB

Page 1 of 2 FCC ID: 2ATPS-G18EB Internal photos Antenna Page 2 of 2 FCC ID: 2ATPS-G18EB

Page 1 of 7 Report No.: AiTSZ-251219058FW2 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. RF Exposure evaluation Product Name : 3D VR VIRTUAL REALITY GLASSES Brand Name : N/A Model : G18EB Series Model : G18, G18E, G18EA, E06, E06EB FCC ID : 2ATPS-G18EB Applicant : Dongguan Shinecon Industrial Co., LTD Address : NO.9 SHIBEI ROAD TANGLI DISTRICT, FENGGANG DONGGUAN, China Manufacturer : Dongguan Shinecon Technology Co., LTD Address : NO.33 Shibei Road Tangli Fenggang Town, Dongguan City, Guangdong China Standard(s) : 47CFR §1.1310, 47CFR §2.1093 KDB447498 D01 General RF Exposure Guidance v06 Date of Receipt : Dec.19, 2025 Date of Test : Dec.19, 2025~ Dec.23, 2025 Issued Date : Dec.23, 2025 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Aalen.Ye Allen Wang Page 2 of 7 Report No.: AiTSZ-251219058FW2 Report Revise Record Report Version Issued Date Notes M0 Dec.23, 2025 Initial Release Page 3 of 7 Report No.: AiTSZ-251219058FW2 Contents 1 GENERAL INFORMATION ....................................................................................................................................... 4 1.1 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 4 1.2 GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 4 1.3 TEST FACILITY .............................................................................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2 METHOD OF MEASUREMENT ................................................................................................................................ 6 2.1 APPLICABLE STANDARD .................................................................................................................................................. 6 2.2 EVALUATION METHOD AND LIMIT .................................................................................................................................... 6 2.3 MANUFACTURING TOLERANCE ........................................................................................................................................ 7 2.4 EVALUATION RESULT ..................................................................................................................................................... 7 2.5 CONCLUSION ............................................................................................................................................................... 7 Page 4 of 7 Report No.: AiTSZ-251219058FW2 1 GENERAL INFORMATION 1.1 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature: 25°C Relative Humidity: 55 % Air Pressure: 101 kPa 1.2 General Description of EUT Product Name: 3D VR VIRTUAL REALITY GLASSES Model/Type reference: G18EB Serial Model: G18, G18E, G18EA, E06, E06EB Model difference: All models are the same except for the model name Power Supply: Input: DC 5.0V DC 3.7V,300mAh by Rechargeable Li-ion polymer battery Adapter Information: N/A Hardware Version: N/A Software Version: N/A Sample(s) Status: AiTSZ-251219058-1(Normal sample) AiTSZ-251219058-2(Engineer sample) Bluetooth : Supported type: Bluetooth BR/EDR Modulation: GFSK, π/4DQPSK, 8DPSK Operation frequency: 2402MHz~2480MHz Channel number: 79 Channel separation: 1MHz Antenna type: PCB antenna Antenna gain: 2.59dBi Remark: The above DUT's information was declared by manufacturer. For more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Page 5 of 7 Report No.: AiTSZ-251219058FW2 1.3 Test Facility Test Laboratory: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong Asia Hongke Test Technology Limited has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. IC —Registration No.: 31737 CAB identifier: CN0165 The 3m Semi-anechoic chamber of Guangdong Asia Hongke Test Technology Limited has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 31737 A2LA-Lab Cert. No.: 7133.01 Guangdong Asia Hongke Test Technology Limited has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2017 …

Text truncated - open the document above for the full version.

Page 1 of 34 Report No.: AiTSZ-251219058FW1 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. TEST REPORT Product Name : 3D VR VIRTUAL REALITY GLASSES Brand Name : N/A Model : G18EB Series Model : G18, G18E, G18EA, E06, E06EB FCC ID : 2ATPS-G18EB Applicant : Dongguan Shinecon Industrial Co., LTD Address : NO.9 SHIBEI ROAD TANGLI DISTRICT, FENGGANG DONGGUAN, China Manufacturer : Dongguan Shinecon Technology Co., LTD Address : NO.33 Shibei Road Tangli Fenggang Town, Dongguan City, Guangdong China Standard(s) : FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of Receipt : Dec.19, 2025 Date of Test : Dec.19, 2025~ Dec.23, 2025 Issued Date : Dec.23, 2025 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Aalen.Ye Allen Wang Page 2 of 34 Report No.: AiTSZ-251219058FW1 Report Revise Record Report Version Issued Date Notes M0 Dec.23, 2025 Initial Release Page 3 of 34 Report No.: AiTSZ-251219058FW1 Contents 1 TEST SUMMARY .................................................................................................................................................... 4 1.1 TEST STANDARDS ......................................................................................................................................................... 4 1.2 TEST SUMMARY ........................................................................................................................................................... 4 1.3 TEST FACILITY .............................................................................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2 GENERAL INFORMATION ....................................................................................................................................... 6 2.1 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 6 2.2 GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 6 2.3 DESCRIPTION OF TEST MODES AND TEST FREQUENCY .......................................................................................................... 7 2.4 SPECIAL ACCESSORIES ................................................................................................................................................... 8 2.5 EQUIPMENT LIST FOR THE TEST ....................................................................................................................................... 8 3 TEST CONDITIONS AND RESULTS ......................................................................................................................... 10 3.1 CONDUCTED EMISSIONS TEST ....................................................................................................................................... 10 3.2 RADIATED EMISSIONS AND BAND EDGE .......................................................................................................................... 13 3.3 MAXIMUM PEAK OUTPUT POWER ................................................................................................................................. 20 3.4 20DB BANDWIDTH ..................................................................................................................................................... 21 3.5 OCCUPIED BANDWIDTH ............................................................................................................................................... 22 3.6 FREQUENCY SEPARATION ............................................................................................................................................. 23 3.7 NUMBER OF HOPPING FREQUENCY ................................................................................................................................. 24 3.8 TIME OF OCCUPANCY (DWELL TIME) .............................................................................................................................. 25 3.9 OUT-OF-BAND EMISSIONS ........................................................................................................................................... 26 3.10 PSEUDORANDOM FREQUENCY HOPPING SEQUENCE .......................................................................................................... 28 3.11 ANTENNA REQUIREMENT ............................................................................................................................................. 29 4 TEST SETUP PHOTOGRAPHS OF EUT .................................................................................................................... 30 5 PHOTOS OF EUT ....................................................................…

Text truncated - open the document above for the full version.

1.BTbBBTExtemalantennapicturena 2.AntennaSize 3.Antenna reflection coefficient As below,Module antenna of SC-G18 are BT single dipoles model which in snake shape, maximum gain is 2.59dbi. Dongguan Shinecon Technology Co., LTD ADD：NO.33 Shibei Road Tangli Fenggang Town, Dongguan City, Guangdong China MARKER 1 Freq=2.4451GHZ dB(ant_SC-B03_mom_a..S(1.1))=32.150 Min 4. Antenna radiation 3D 2D 5.Antenna efficiency Radiation Pattern

Page 1 of 55 Report No.: AiTSZ-251219058FW1 Appendix Test Data for BT_BREDR Page 2 of 55 Report No.: AiTSZ-251219058FW1 1. Bandwidth 1.1 Test Result 1.1.1 OBW Mode TX Type Frequency (MHz) Packet Type ANT 99% Occupied Bandwidth (MHz) Verdict Result Limit GFSK SISO 2402 DH5 1 0.744 / Pass 2441 DH5 1 0.746 / Pass 2480 DH5 1 0.752 / Pass Pi/4DQPSK SISO 2402 2DH5 1 1.144 / Pass 2441 2DH5 1 1.145 / Pass 2480 2DH5 1 1.149 / Pass 8DPSK SISO 2402 3DH5 1 1.156 / Pass 2441 3DH5 1 1.148 / Pass 2480 3DH5 1 1.159 / Pass 1.1.2 20dB BW Mode TX Type Frequency (MHz) Packet Type ANT 20dB Bandwidth (MHz) Verdict Result Limit GFSK SISO 2402 DH5 1 0.849 / Pass 2441 DH5 1 0.845 / Pass 2480 DH5 1 0.846 / Pass Pi/4DQPSK SISO 2402 2DH5 1 1.279 / Pass 2441 2DH5 1 1.274 / Pass 2480 2DH5 1 1.276 / Pass 8DPSK SISO 2402 3DH5 1 1.280 / Pass 2441 3DH5 1 1.294 / Pass 2480 3DH5 1 1.280 / Pass Page 3 of 55 Report No.: AiTSZ-251219058FW1 1.2 Test Graph 1.2.1 OBW GFSK_DH5_LCH_2402MHz_Ant1_NTNV GFSK_DH5_MCH_2441MHz_Ant1_NTNV Page 4 of 55 Report No.: AiTSZ-251219058FW1 GFSK_DH5_HCH_2480MHz_Ant1_NTNV Pi/4DQPSK_2DH5_LCH_2402MHz_Ant1_NTNV Page 5 of 55 Report No.: AiTSZ-251219058FW1 Pi/4DQPSK_2DH5_MCH_2441MHz_Ant1_NTNV Pi/4DQPSK_2DH5_HCH_2480MHz_Ant1_NTNV Page 6 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_LCH_2402MHz_Ant1_NTNV 8DPSK_3DH5_MCH_2441MHz_Ant1_NTNV Page 7 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_HCH_2480MHz_Ant1_NTNV Page 8 of 55 Report No.: AiTSZ-251219058FW1 1.2.2 20dB BW GFSK_DH5_LCH_2402MHz_Ant1_NTNV GFSK_DH5_MCH_2441MHz_Ant1_NTNV Page 9 of 55 Report No.: AiTSZ-251219058FW1 GFSK_DH5_HCH_2480MHz_Ant1_NTNV Pi/4DQPSK_2DH5_LCH_2402MHz_Ant1_NTNV Page 10 of 55 Report No.: AiTSZ-251219058FW1 Pi/4DQPSK_2DH5_MCH_2441MHz_Ant1_NTNV Pi/4DQPSK_2DH5_HCH_2480MHz_Ant1_NTNV Page 11 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_LCH_2402MHz_Ant1_NTNV 8DPSK_3DH5_MCH_2441MHz_Ant1_NTNV Page 12 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_HCH_2480MHz_Ant1_NTNV Page 13 of 55 Report No.: AiTSZ-251219058FW1 2. Maximum Conducted Output Power 2.1 Test Result 2.1.1 Power Mode TX Type Frequency (MHz) Packet Type Maximum Peak Conducted Output Power (dBm) Verdict ANT1 Limit GFSK SISO 2402 DH5 -0.91 <=30 Pass 2441 DH5 1.02 <=30 Pass 2480 DH5 0.58 <=30 Pass Pi/4DQPSK SISO 2402 2DH5 -1.48 <=20.97 Pass 2441 2DH5 0.48 <=20.97 Pass 2480 2DH5 -0.02 <=20.97 Pass 8DPSK SISO 2402 3DH5 -1.55 <=20.97 Pass 2441 3DH5 0.39 <=20.97 Pass 2480 3DH5 -0.10 <=20.97 Pass Note1: Antenna Gain: Ant1: 2.59dBi; Page 14 of 55 Report No.: AiTSZ-251219058FW1 2.2 Test Graph 2.2.1 Power GFSK_DH5_LCH_2402MHz_Ant1_NTNV GFSK_DH5_MCH_2441MHz_Ant1_NTNV Page 15 of 55 Report No.: AiTSZ-251219058FW1 GFSK_DH5_HCH_2480MHz_Ant1_NTNV Pi/4DQPSK_2DH5_LCH_2402MHz_Ant1_NTNV Page 16 of 55 Report No.: AiTSZ-251219058FW1 Pi/4DQPSK_2DH5_MCH_2441MHz_Ant1_NTNV Pi/4DQPSK_2DH5_HCH_2480MHz_Ant1_NTNV Page 17 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_LCH_2402MHz_Ant1_NTNV 8DPSK_3DH5_MCH_2441MHz_Ant1_NTNV Page 18 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_HCH_2480MHz_Ant1_NTNV Page 19 of 55 Report No.: AiTSZ-251219058FW1 3. Carrier Frequency Separation 3.1 Test Result 3.1.1 Ant1 Ant1 Mode TX Type Frequency (MHz) Packet Type Channel Separation (MHz) 20dB Bandwidth (MHz) Limit (MHz) Verdict GFSK SISO HOPP DH5 1.006 0.849 >=0.849 Pass Pi/4DQPSK SISO HOPP 2DH5 1.001 1.279 >=0.853 Pass 8DPSK SISO HOPP 3DH5 1.001 1.294 >=0.863 Pass Page 20 of 55 Report No.: AiTSZ-251219058FW1 3.2 Test Graph 3.2.1 Ant1 GFSK_DH5_HOPP_Ant1_NTNV Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Page 21 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_HOPP_Ant1_NTNV Page 22 of 55 Report No.: AiTSZ-251219058FW1 4. Number of Hopping Frequencies 4.1 Test Result 4.1.1 HoppNum Mode TX Type Frequency (MHz) Packet Type Num of Hopping Frequencies Verdict ANT1 Limit GFSK SISO HOPP DH5 79 >=15 Pass Pi/4DQPSK SISO HOPP 2DH5 79 >=15 Pass 8DPSK SISO HOPP 3DH5 79 >=15 Pass Page 23 of 55 Report No.: AiTSZ-251219058FW1 4.2 Test Graph 4.2.1 HoppNum GFSK_DH5_HOPP_Ant1_NTNV Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Page 24 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_HOPP_Ant1_NTNV Page 25 of 55 Report No.: AiTSZ-251219058FW1 5. Time of Occupancy (Dwell Time) 5.1 Test Result 5.1.1 Ant1 Ant1 Mode TX Type Frequency (MHz) Packet Type Duration of Single Pulse (ms) Observation Period (s) Num of Pulse in Observation Period Dwell Time (ms) Limit (ms) Verdict GFSK SISO HOPP DH1 0.380 31.600 321 121.980 <=400 Pass DH3 1.636 31.600 161 263.396 <=400 Pass DH5 2.898 31.600 119 344.862 <=400 Pass Pi/4DQPSK SISO HOPP 2DH1 0.418 31.600 319 133.342 <=400 Pass 2DH3 1.654 31.600 164 271.256 <=400 Pass 2DH5 2.920 31.600 113 329.960 <=400 Pass 8DPSK SISO HOPP 3DH1 0.388 31.600 319 123.772 <=400 Pass 3DH3 1.652 31.600 160 264.320 <=400 Pass 3DH5 2.904 31.600 116 336.864 <=400 Pass Page 26 of 55 Report No.: AiTSZ-251219058FW1 5.2 Test Graph 5.2.1 Ant1 GFSK_DH1_HOPP_Ant1_NTNV GFSK_DH1_HOPP_Ant1_NTNV Page 27 of 55 Report No.: AiTSZ-251219058FW1 GFSK_DH3_HOPP_Ant1_NTNV GFSK_DH3_HOPP_Ant1_NTNV Page 28 of 55 Report No.: AiTSZ-251219058FW1 GFSK_DH5_HOPP_Ant1_NTNV GFSK_DH5_HOPP_Ant1_NTNV Page 29 of 55 Report No.: AiTSZ-251219058FW1 Pi/4DQPSK_2DH1_HOPP_Ant1_NTNV Pi/4DQPSK_2DH1_HOPP_Ant1_NTNV Page 30 of 55 Report No.: AiTSZ-251219058FW1 Pi/4DQPSK_2DH3_HOPP_Ant1_NTNV Pi/4DQPSK_2DH3_HOPP_Ant1_NTNV Page 31 of 55 Report No.: AiTSZ-251219058FW1 Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Pi/4DQPSK_2DH5_HOPP_Ant1_NTNV Page 32 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH1_HOPP_Ant1_NTNV 8DPSK_3DH1_HOPP_Ant1_NTNV Page 33 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH3_HOPP_Ant1_NTNV 8DPSK_3DH3_HOPP_Ant1_NTNV Page 34 of 55 Report No.: AiTSZ-251219058FW1 8DPSK_3DH5_HOPP_Ant1_NTNV 8DPSK_3DH5_HOPP_Ant1_NTNV Page 35 of 55 Report No.: AiTSZ-251219058FW1 6. Unwanted Emissions In Non-restricted Frequency Bands 6.1 Test Result 6.1.1 Ref Mode TX Type Frequency (MHz) Packet Type ANT Level of Reference (dBm) GFSK SISO 2402 DH5 1 -1.46 2441 DH5 1 0.49 2480 DH5 1 0.01 HOPP DH5 1 0.92 0.92 Pi/4DQPSK SISO 2402 2DH5 1 -1.…

Text truncated - open the document above for the full version.

Page 1 of 2 FCC ID: 2ATPS-G18EB Page 2 of 2 FCC ID: 2ATPS-G18EB