2AUCK-PDWM95UHF WIRELESS MICROPHONE

FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device can be used in portable exposure condition without restriction.

Local Representative Letter For Certification Service in the USA Federal Communications Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 To whom it may concern Pursuant to Section 2.911(d)(7), of the Commission’s Rules (47 C.F.R.) we attest as follows for the product listed below: FCC ID Model name 2AUCK-PDWM95 PDWM95, PDWM96, PDWM97, PDWM98, PDWM99, PDWMU105, PDWMU106, PDWMU107, PDWMU108, PDWMU109, PDWMU112,FS-100, FS-101, FS-102, FS-103, FS-104, FS-105, FS-106, FS-107, FS-108, FS- 109, FS-111, FS-112, FS-113, FS-114, FS-115, FS-116, FS-117, FS-118, FS-119, FS-120, FS- 201, FS-202, FS-203, FS-204, FS-205, FS-206, FS-207, FS-208, FS-209, FS-210, FS-211, FS- 212, FS-213, FS-214, FS-215, FS-216, FS-217, FS-218, FS-219, FS-220, FS-122, FS-133, FS- 155, FS-166, FS-177, FS-188, FS-199, FS-200, FS-222, FS-233, FS-255, FS-266, FS-277, FS- 288, FS-299, FS-2024, FS-2025, FS-2026, FS- 2027, FS-2028, FS-2029, FS-2030, AIRFREE- X2HH, AIRFREE-X2MH, Vocal Wonder U1, VocalAi202 We hereby acknowledge as follows: i. both signees confirm that the point of contact accepts responsibility to act as a US- American Representative on behalf of the applicant ii. the point of contact provides the physical U.S. address and email as listed below iii. both parties maintain the requirements of this agreement for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. iv. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. US-American Point of Contact Applicant/Approval Holder Signature Date: 2026-1-19 Signature Date: 2026-1-19 Company Name: GLOCERTS TECHNOLOGY INC Enping Fly Sound Equipment Co.,Ltd. FRN: 0036339737 0032255309 Contact Name: Huiying Fan BOEY TAN Address: 19784 SUNKISSED RIDGE DR, RIVERSIDE, CA 92507 Fourth Floor, 12th Building, No. 33, Enzhou Industrial Avenue, Enping City, Guangdong Province, China Phone: (626) 588-8039 +86 13929092202 Email: [email protected] [email protected]

Page 1 of 2 FCC ID: 2AUCK- PDWM95 External Photos Page 2 of 2 FCC ID: 2AUCK- PDWM95

Label 1. The label is silk-screen on the sample FCC ID: 2AUCK- PDWM95

Page 1 of 3 FCC ID: 2AUCK- PDWM95 Internal photos Page 2 of 3 FCC ID: 2AUCK- PDWM95 Antenna Page 3 of 3 FCC ID: 2AUCK- PDWM95

Page 1 of 7 Report No.: AiTSZ-251229012FW2 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. RF Exposure evaluation Product Name : UHF WIRELESS MICROPHONE Brand Name : Model : PDWM95 Series Model : See page 6 FCC ID : 2AUCK-PDWM95 Applicant : Enping Fly Sound Equipment Co.,Ltd. Address : Fourth Floor, 12th Building, No. 33, Enzhou Industrial Avenue, Enping City, Guangdong Province, China Manufacturer : Enping Fly Sound Equipment Co.,Ltd. Address : Fourth Floor, 12th Building, No. 33, Enzhou Industrial Avenue, Enping City, Guangdong Province, China Standard(s) : 47CFR §1.1310, 47CFR §2.1093 KDB447498 D01 General RF Exposure Guidance v06 Date of Receipt : Dec. 29, 2025 Date of Test : Dec. 29, 2025~ Jan. 14, 2026 Issued Date : Jan. 14, 2026 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Aalen.Ye Allen Wang Page 2 of 7 Report No.: AiTSZ-251229012FW2 Report Revise Record Report Version Issued Date Notes M0 Jan. 14, 2026 Initial Release Page 3 of 7 Report No.: AiTSZ-251229012FW2 Contents 1 GENERAL INFORMATION .......................................................................................................................................... 4 1.1 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 4 1.2 GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 4 1.3 TEST FACILITY .............................................................................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2 METHOD OF MEASUREMENT ................................................................................................................................... 6 2.1 APPLICABLE STANDARD.................................................................................................................................................. 6 2.2 EVALUATION METHOD AND LIMIT .................................................................................................................................... 6 2.3 MANUFACTURING TOLERANCE ........................................................................................................................................ 7 2.4 EVALUATION RESULT ..................................................................................................................................................... 7 2.5 CONCLUSION ............................................................................................................................................................... 7 Page 4 of 7 Report No.: AiTSZ-251229012FW2 1 GENERAL INFORMATION 1.1 Environmental conditions During the measurement the environmental conditions were within the listed ranges: Normal Temperature: 25°C Relative Humidity: 55 % Air Pressure: 101 kPa 1.2 General Description of EUT Product Name: UHF WIRELESS MICROPHONE Model/Type reference: PDWM95 Serial Model: PDWM96, PDWM97, PDWM98, PDWM99, PDWMU105, PDWMU106, PDWMU107, PDWMU108, PDWMU109, PDWMU112,FS-100, FS- 101, FS-102, FS-103, FS-104, FS-105, FS-106, FS-107, FS-108, FS- 109, FS-111, FS-112, FS-113, FS-114, FS-115, FS-116, FS-117, FS- 118, FS-119, FS-120, FS-201, FS-202, FS-203, FS-204, FS-205, FS- 206, FS-207, FS-208, FS-209, FS-210, FS-211, FS-212, FS-213, FS- 214, FS-215, FS-216, FS-217, FS-218, FS-219, FS-220, FS-122, FS- 133, FS-155, FS-166, FS-177, FS-188, FS-199, FS-200, FS-222, FS- 233, FS-255, FS-266, FS-277, FS-288, FS-299, FS-2024, FS-2025, FS-2026, FS-2027, FS-2028, FS-2029, FS-2030, AIRFREE-X2HH, AIRFREE-X2MH, Vocal Wonder U1, VocalAi202 Model difference: All models are same as the samples except model name, all the models are electrical identical same mechanical structure and design. Power Supply: DC 3.70V from battery Hardware Version: 1.0 Software Version: 1.0 Sample(s) Status: AiTSZ-241218022-1(Normal sample) AiTSZ-241218022-2(Engineer sample) Wireless microphone: Frequency: 470.2MHz-607.8MHz Channel number: 689 Nominal channel bandwidth 200KHz Modulation Type: FM Antenna type: PCB antenna Antenna gain: -2.71dBi Remark: The above DUT's information was declared by manufacturer. For more detailed features description, please refer to the manufacturer’s specifications or the User's Manual.. Page 5 of 7 Report No.: AiTSZ-251229012FW2 1.3 Test Facility Test Laboratory: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China The test facility is recognized, certified or accredited by the following organizations: FCC-Registration No.: 251906 Designation Number: CN1376 Guangdong Asia Hongke Test Technology Limited has…

Text truncated - open the document above for the full version.

Page 1 of 28 Report No.: AiTSZ-251229012FW1 Note: This device has been tested and found to comply with the standard(s) listed, this test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. This report shall not be reproduced except in full, without the written approval of Guangdong Asia Hongke Test Technology Limited. If there is a need to alter or revise this document, the right belongs to Guangdong Asia Hongke Test Technology Limited, and it should give a prior written notice of the revision document. This test report must not be used by the client to claim product endorsement. Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China. TEST REPORT Product Name : UHF WIRELESS MICROPHONE Brand Name : Model : PDWM95 Series Model : See page 6 FCC ID : 2AUCK-PDWM95 Applicant : Enping Fly Sound Equipment Co.,Ltd. Address : Fourth Floor, 12th Building, No. 33, Enzhou Industrial Avenue, Enping City, Guangdong Province, China Manufacturer : Enping Fly Sound Equipment Co.,Ltd. Address : Fourth Floor, 12th Building, No. 33, Enzhou Industrial Avenue, Enping City, Guangdong Province, China Standard(s) : FCC CFR Title 47 Part 15 Subpart C Section 15.236 Date of Receipt : Dec. 29, 2025 Date of Test : Dec. 29, 2025~ Jan. 14, 2026 Issued Date : Jan. 14, 2026 Issued By: Guangdong Asia Hongke Test Technology Limited B1/F, Building 11, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Tel.: +86 0755-230967639 Fax.: +86 0755-230967639 Reviewed by: Approved by: Aalen.Ye Allen Wang Page 2 of 28 Report No.: AiTSZ-251229012FW1 Report Revise Record Report Version Issued Date Notes M0 Jan. 14, 2026 Initial Release Page 3 of 28 Report No.: AiTSZ-251229012FW1 Contents 1 TEST SUMMARY ....................................................................................................................................................... 4 1.1 TEST STANDARDS ......................................................................................................................................................... 4 1.2 TEST SUMMARY ........................................................................................................................................................... 4 1.3 TEST FACILITY .............................................................................................................................................................. 5 1.4 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2 GENGENERAL INFORMATION ................................................................................................................................... 6 2.1 ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 6 2.2 GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 6 2.3 DESCRIPTION OF TEST MODES AND TEST FREQUENCY .......................................................................................................... 7 2.4 SPECIAL ACCESSORIES ................................................................................................................................................... 7 2.5 EQUIPMENT LIST FOR THE TEST ....................................................................................................................................... 7 3 TEST CONDITIONS AND RESULTS .............................................................................................................................. 9 3.1 CONDUCTED EMISSIONS TEST ......................................................................................................................................... 9 3.2 MAXIMUM OUTPUT POWER ....................................................................................................................................... 12 3.3 OCCUPIED BANDWIDTH ............................................................................................................................................... 14 3.4 NECESSARY BANDWIDTH.............................................................................................................................................. 16 3.5 TRANSMITTER SPURIOUS EMISSIONS............................................................................................................................... 19 3.6 FREQUENCY STABILITY ................................................................................................................................................. 21 4 TEST SETUP PHOTOGRAPHS OF EUT ....................................................................................................................... 23 5 PHOTOS OF EUT ..................................................................................................................................................... 24 Page 4 of 28 Report No.: AiTSZ-251229012FW1 1 TEST SUMMARY 1.1 Test Standards The tests were performed according to following standards: FCC Rules Part 15.236: Operation of wireless microphones in the bands 54-72 MHz, 76-88 MHz, 174-216 MHz, 470-608 MHz and 614-698 MHz. ANSI C63.10: 2020: American National Standard for Testing Unlicensed Wireless Devices 1.2 Test Summary Test Item Section in 47 CFR Result RF Power Output §15.236(d) Pass Occupied Bandwidth §15.236(f)(2) Pass Necessary Bandwidth §15.236(g) Pass Spurious emissions §15.236(g) Pass Frequency Stability §15.236(f)(3) Pass Conducted Emissions §15.207 Pass Page 5 of 28 Report No.: AiTSZ-251229012FW1 1.3 Test Fa…

Text truncated - open the document above for the full version.

PCB antenna

Page 1 of 2 FCC ID: 2AUCK- PDWM95 Page 2 of 2 FCC ID: 2AUCK- PDWM95