2AUDO-F5Wireless Charger

Model:F5 Wireless Charger User GuideUser Guide 1 2 3 Put the aripods in the center of the charging area for wireless charging. About Airpods LED indicator light PD/QC3.0 Type-C to Type-A The Max Output: Apple.5W, Samsung 10W. Please use PD or QC 3.0 adapter. The wireless charging can be 5W only if chosing a 5V2A adapter. 7 About adapterAbout adapter Step 1: Disassemble back-case. Step2: Disassemble metal parts. Break it apart with your fingernail. About steps to assemble Apple watch magetic charger cable Take it apart with your fingernail, and the rest of parts can be opened gently by fingernail. Step3: Apple watch magnetic charger cable layout 1. Pass the charger cable USB through the hole. Step4: Apple watch magnetic charger cable layout 2. Take charger cable in the groove by following 1-3 order, pass the USD though the bottom hole, as shown in the picture. Step5: Apple watch magnetic charger cable layout 3. Take charger cable in the groove by following 1-6 order, insert the USB into the PCBA, buckle the back case, as shown in the picture, The whole charger cable layout is finished. USB 1 2 3 4 5 6 White light: Standby Blue light: Charging Red light flash: Error White LED light and blue LED light will be darken after 15 minutes, not influence your sleep. ● Do not use output of 5V1A adaptor, 5W low- power adaptor will make wireless charger to work unsteadily. ● About adapterCharging status & tĂƌŶŝŶŐ ^ƚĂƚĞŵĞŶƚ ŚĂŶŐĞƐ Žƌ ŵŽĚŝĨŝĐĂƚŝŽŶƐ ŶŽƚ ĞdžƉƌĞƐƐůLJ ĂƉƉƌŽǀĞĚ ďLJ ƚŚĞ ƉĂƌƚLJ ƌĞƐƉŽŶƐŝďůĞ ĨŽƌ ĐŽŵƉůŝĂŶĐĞ ĐŽƵůĚ ǀŽŝĚ ƚŚĞ ƵƐĞƌ͛Ɛ ĂƵƚŚŽƌŝƚLJ ƚŽ ŽƉĞƌĂƚĞ ƚŚĞ ĞƋƵŝƉŵĞŶƚ͘ dŚŝƐ ĞƋƵŝƉŵĞŶƚ ŚĂƐ ďĞĞŶ ƚĞƐƚĞĚ ĂŶĚ ĨŽƵŶĚ ƚŽ ĐŽŵƉůLJ ǁŝƚŚ ƚŚĞ ůŝŵŝƚƐ ĨŽƌ Ă ůĂƐƐ  ĚŝŐŝƚĂů ĚĞǀŝĐĞ͕ ƉƵƌƐƵĂŶƚ ƚŽ WĂƌƚ ϭρ ŽĨ ƚŚĞ & ZƵůĞƐ͘ dŚĞƐĞ ůŝŵŝƚƐ Ăƌ Ğ ĚĞƐŝŐŶĞĚ ƚŽ ƉƌŽ ǀŝĚĞ ƌĞĂƐŽŶĂďůĞ ƉƌŽƚĞĐƚŝŽŶ ĂŐĂŝŶƐƚ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ŝŶ Ă ƌĞƐŝĚĞŶƚŝĂů ŝŶƐƚĂůůĂƚŝŽŶ͘ dŚŝƐ ĞƋƵŝƉŵĞŶƚ ŐĞŶĞƌĂƚĞƐ ƵƐĞƐ ĂŶĚ ĐĂŶ ƌĂĚŝĂƚĞ ƌĂĚŝŽ ĨƌĞƋƵĞŶĐLJ ĞŶĞƌŐLJ ĂŶĚ͕ ŝĨ ŶŽƚ ŝŶƐƚĂůůĞĚ ĂŶĚ ƵƐĞĚ ŝŶ ĂĐĐŽƌĚĂŶĐĞ ǁŝƚŚ ƚŚĞ ŝŶƐƚƌƵĐƚŝŽŶƐ͕ ŵĂLJ ĐĂƵƐĞ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ƚŽ ƌĂĚŝŽ ĐŽŵŵƵŶŝĐĂƚŝŽŶƐ͘ ,ŽǁĞǀĞƌ͕ ƚŚĞƌĞ ŝƐ ŶŽ ŐƵĂƌĂŶƚĞĞ ƚŚĂƚ ŝŶƚĞƌĨĞƌĞŶĐĞ ǁŝůů ŶŽƚ ŽĐĐƵƌ ŝŶ Ă ƉĂ ƌƚ ŝĐƵůĂƌ ŝŶƐƚĂůůĂƚŝŽŶ͘ /Ĩ ƚŚŝƐ ĞƋƵŝƉŵĞŶƚ ĚŽĞƐ ĐĂƵƐĞ ŚĂƌŵĨƵů ŝŶƚĞƌĨĞƌĞŶĐĞ ƚŽ ƌĂĚŝŽ Žƌ ƚĞůĞǀŝƐŝŽŶ ƌĞĐĞƉƚŝŽŶ͕ ǁŚŝĐŚ ĐĂŶ ďĞ ĚĞƚĞƌŵŝŶĞĚ ďLJ ƚƵƌŶŝŶŐ ƚŚĞ ĞƋƵŝƉŵĞŶƚ ŽĨĨ ĂŶĚ ŽŶ͕ ƚŚĞ ƵƐĞƌ ŝƐ ĞŶĐŽƵƌĂŐĞĚ ƚŽ ƚƌLJ ƚŽ ĐŽƌƌĞĐƚ ƚŚĞ ŝŶƚĞƌĨĞƌĞŶĐĞ ďLJ ŽŶĞ Žƌ ŵŽƌĞ ŽĨ ƚŚĞ ĨŽůůŽǁŝŶŐ ŵĞĂƐƵƌĞƐ͗ ‐‐ ZĞŽƌŝĞŶƚ Žƌ ƌĞůŽĐĂƚĞ ƚŚĞ ƌ ĞĐĞŝǀŝŶŐ ĂŶƚ ĞŶŶĂ͘ ‐‐ /ŶĐƌĞĂƐĞ ƚŚĞ ƐĞƉĂƌĂƚŝŽŶ ďĞƚǁĞĞŶ ƚŚĞ ĞƋƵŝƉŵĞŶƚ ĂŶĚ ƌĞĐĞŝǀĞƌ͘ ‐‐ ŽŶŶĞĐƚ ƚŚĞ ĞƋƵŝƉŵĞŶƚ ŝŶƚŽ ĂŶ ŽƵƚůĞƚ ŽŶ Ă ĐŝƌĐƵŝƚ ĚŝĨĨĞƌĞŶƚ ĨƌŽŵ ƚŚĂƚ ƚŽ ǁŚŝĐŚ ƚŚĞ ƌĞĐĞŝǀĞƌ ŝƐ ĐŽŶŶĞĐƚĞĚ͘ ‐‐ ŽŶƐƵůƚ ƚŚĞ ĚĞĂůĞƌ Žƌ ĂŶ ĞdžƉĞƌŝĞŶĐĞĚ ƌĂĚŝŽͬds ƚĞĐŚŶŝĐŝĂŶ ĨŽƌ ŚĞůƉ͘ Z& džƉŽƐƵƌĞ͗  ĚŝƐƚĂŶĐĞ ŽĨ ϭρ Đŵ ƐŚĂůů ďĞ ŵĂŝŶƚĂŝŶĞĚ ďĞƚǁĞĞŶ ƚŚĞ ĂŶƚĞŶŶĂ ĂŶĚ ƵƐĞƌƐ͕ ĂŶĚ ƚŚĞ ƚƌĂŶƐŵŝƚƚĞƌ ŵĂLJ ŶŽƚ ďĞ ĐŽ‐ůŽĐĂƚĞĚ ǁŝƚŚ ĂŶLJ ŽƚŚĞƌ ƚƌĂŶƐŵŝƚƚĞƌ Žƌ ĂŶƚĞŶŶĂ͘ dŚŝƐĚĞǀŝĐĞĐŽŵƉůŝĞƐǁŝƚŚƉĂƌƚϭρŽĨƚŚĞ&ZƵůĞƐ͘KƉĞƌĂƚŝŽŶŝƐƐƵďũĞĐƚƚŽƚŚĞĨŽůůŽǁŝŶŐƚǁŽĐŽŶĚŝƚŝŽŶƐ͗ ;ϭͿdŚŝƐĚĞǀŝĐĞŵĂLJŶŽƚĐĂƵƐĞŚĂƌŵĨƵůŝŶƚĞƌĨĞƌĞŶĐĞ͕ĂŶĚ;ϮͿƚŚŝƐĚĞǀŝĐĞ ŵƵƐƚĂĐĐĞƉƚĂŶLJŝŶƚĞƌĨĞƌĞŶĐĞƌĞĐĞŝ ǀĞĚ͕ŝŶĐůƵĚŝŶŐŝŶƚĞƌĨĞƌĞŶĐĞƚŚĂƚŵĂLJĐĂƵƐĞƵŶĚĞƐŝƌĞĚŽƉĞƌĂƚŝŽŶ͘

Co m Ad d Dist Pr o Mo d Pr o We act We an d issu our Sig Na m Title Com mpany: Sh dress: 5F,B trict Shenz oduct Name del Numbe oduct Desc authorize M on our beha declare tha d certificatio ues concern behalf shal nature: me: e: mpany: enzhen Itia Bld. C, Hon zhen, China e: Wireless er(s): F5 ription: Wi MiCOM Lab alf on all ma at MiCOM L n of equipm ning the app ll have the s Jiankun Z h Manager Shenzhen Shenzhe Agen an Technol ngde Ind. P a s Charger reless Ch a bs Inc., 575 atters conce Labs Inc. is ment to the r proval applic same effect hao n Itian Techn en Itian Tec nt Auth logy CO.,LT ark, Shigua arger Boulder C o erning the c allowed to f regulatory a cation. Any t as acts of nology CO. hnology CO horizat TD an, Lianrun ourt, Pleasa certification forward all i agencies as and all acts our own. ,LTD O.,LTD tion n Rd.Dalan anton, Califo of above na information s required a s carried ou Date: ng St., Long ornia 94566 amed equip related to t nd to discu ut by MiCOM Jan. 18, 202 ghua 6, USA, to pment. the approva ss any M Labs on 21 al

Office o Federa 7435 O Columb USA Subjec t FCC ID To Wh o Pursua are req u docume These d propriet might b It is ou r corresp docume authoriz Sincer e Signat u Name: J Title: M of Engineeri l Communic Oakland Mills bia, MD 210 t; Request f D: 2AUDO- om It May C nt to the pro uesting the ents from pu documents tary informa be harmful to Schema Block D Parts Lis Operatio r understand pondence du ents and thi zation is iss ely, ure: Jiankun Zha anager ing Techno cations Com s Road 046 for Confiden F5 Concern, ovisions of t Commissio ublic disclos contain det ation in ope o our comp atic Diagram iagram st onal Descri ding that all uring the ce s informatio sued. ao Shenzhen logy mmission ntiality the Commis on to withho sure indefin tailed syste ration of th e any and wo m ption l measurem ertification re on will be av Itian Techn ssion’s rule old the follow nitely. m and equi e equipmen ould give co ment test rep eview proce vailable for ology CO., L s Title 47 S wing attach pment desc nt. The publ ompetitors a ports, FCC ess cannot public revi e LTD Sections §0. hment(s) as criptions an ic disclosu r an unfair ad ID label for be granted ew once the Date: Jan. 457 and §0 confidentia d are consi re of these d vantage in mat and as confide n e grant of eq 18, 2021 0.459, we al dered as documents the market . ntial quipment .

Annex A External Photos Report No.: HK2012253989‐1E/2E Page 1 of 4 Report No.: HK2012253989‐1E/2E Page 2 of 4 Report No.: HK2012253989‐1E/2E Page 3 of 4 Report No.: HK2012253989‐1E/2E Page 4 of 4

FCC ID LABEL: Label Location

Annex B Internal Photo Report No.:HK2012253989-1E/2E Page 1 of 8 Antenna Report No.:HK2012253989-1E/2E Page 2 of 8 Mobile Phone Charging Antenna 2 Mobile Phone Charging Antenna 1 Report No.:HK2012253989-1E/2E Page 3 of 8 Report No.:HK2012253989-1E/2E Page 4 of 8 Report No.:HK2012253989-1E/2E Page 5 of 8 Report No.:HK2012253989-1E/2E Page 6 of 8 Report No.:HK2012253989-1E/2E Page 7 of 8 Report No.:HK2012253989-1E/2E Page 8 of 8

Page 1 of 8 Report No.: HK2012253989-2E FCC TEST REPORT Test report On Behalf of Shenzhen Itian Technology CO.,LTD For Wireless Charger Model No.: F5 FCC ID: 2AUDO-F5 Prepared for : Shenzhen Itian Technology CO.,LTD 5F,Bld. C, Hongde Ind. Park, Shiguan, Lianrun Rd.Dalang St., Longhua District Shenzhen, China Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Fuhai Street, Bao'an District, Shenzhen City, China Date of Test: Dec. 25, 2020 ~Jan. 04, 2021 Date of Report: Jan. 04, 2021 Report Number: HK2012253989-2E Page 2 of 8 Report No.: HK2012253989-2E Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. 2. Channel List Channel Frequency (KHz) Channel Frequency (MHz) Channel Frequency (MHz) Channel Frequency (MHz) 01 125 The EUT antenna is Coil Antenna. No antenna other than that furnished by the responsible party shall be used with the device. 2. SUMMARY OF TEST RESULTS 2.1 Test procedures according to the technical standards: FCC KDB680106 D01 RF Exposure Wireless Charging Apps v03 FCC CFR 47 Standard Section Test Item Judgment Remark FCC CFR 47 part1, 1.1310 KDB680106 D01v03 (3)(3) Electric Field Strength (E) (V/m) PASS Magnetic Field Strength (H) (A/m) PASS 2.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ±U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 All emissions,radiated(<30M)(9KHz-30MHz) ±4.26dB 2 Temperature ±0.5°C 3 Humidity ±2% Page 3 of 8 Report No.: HK2012253989-2E 2.3 Test Instruments Description Brand Model No. Frequency Range Calibrated Date Calibrated Until Broadband Field Meter NARDA NBM-550 - Jun. 18, 2020 Jun. 17, 2021 Magnetic Field Meter NARDA ELT-400 1 – 400kHz Jun. 18, 2020 Jun. 17, 2021 Magnetic Probe NARDA HF-3061 300kHz – 30MHz Jun. 18, 2020 Jun. 17, 2021 Magnetic Probe NARDA HF-0191 27 – 1000MHz Jun. 18, 2020 Jun. 17, 2021 Broadband Field Meter NARDA NBM-550 - Jun. 18, 2020 Jun. 17, 2021 Electric Field Meter COMBINOVA EFM 2005Hz – 400kHz Jun. 18, 2020 Jun. 17, 2021 E-Field Probe NARDA EF-0391 100kHz – 3GHz Jun. 18, 2020 Jun. 17, 2021 E-Field Probe NARDA EF-6091 100MHz – 60GHz Jun. 18, 2020 Jun. 17, 2021 lsotropic Electric Field| Probe NARDA EP-601 511WX60706 Jun. 18, 2020 Jun. 17, 2021 NOTE: 1. The calibration interval of the above test instruments is 12 months . Page 4 of 8 Report No.: HK2012253989-2E 3. MAXIMUM PERMISSIBLE EXPOSURE 3.1 MAXIMUM PERMISSIBLE EXPOSURE Limit of Maximum Permissible Exposure Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180 / f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1 30 Note 1: f = frequency in MHz ; *Plane-wave equivalent power density Note 2: For the applicable limit, see FCC 1.1310, 680106 D01 RF Exposure Wireless Charging Apps v03 Note 3: Emissions between 100 kHz to 300 kHz should be assessed versus the limits at 300 kHz in Table 1 of Section 1.1310: 614 V/m and 1.63A/m. A KDB inquiry is required to determine the applicable exposure limits below 100 kHz. Page 5 of 8 Report No.: HK2012253989-2E 4. TEST PROCEDURE a. For devices designed for typical desktop applications, such a wireless charging pads, RF exposure evaluation should be conducted assuming a user separation distance of (H-field & E- field strengths for all sides is 15cm, H-field strengths of top side is 20cm). E and H field strength measurements or numerical modeling may be used to demonstrate compliance. Measurements should be made from all sides and the top of the primary/client pair, with the 15 cm measured from the center of the probe(s) to the edge of the device. 4.1 TEST SETUP 4.2 RESULT OF MAXIMUM PERMISSIBLE EXPOSURE Page 6 of 8 Report No.: HK2012253989-2E For Full load mode: E-Field Strength at 15 cm from the edges surrounding the EUT (V/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (V/m) 0.125 1.23 1.39 1.45 1.76 1.29 614 H-Field Strength at 15 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (A/m) 0.125 0.24 0.19 0.21 0.16 0.27 1.63 For Half Load mode: E-Field Strength at 15 cm from the edges surrounding the EUT (V/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (V/m) 0.125 1.39 1.47 1.33 1.68 1.57 614 H-Field Strength at 15 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (A/m) 0.125 0.15 0.23 0.19 0.20 0.22 1.63 Page 7 of 8 Report No.: HK2012253989-2E For No load mode: E-Field Strength at 15 cm from the edges surrounding the EUT (V/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (V/m) 0.125 1.31 1.42 1.69 1.49 1.61 614 H-Field Strength at 15 cm from the edges surrounding the EUT (A/m) Frequency Range (MHz) Test Position A Test Position B Test Position C Test Position D Test Position E Limits Test (A/m) 0.125 0.19 0.22 0.24 0.17 0.23 1.63 Remark: According KDB 680106 D01 RF Exposure Wireless Charging App v03, section 5, b). The aggregate H-field strengths at 15 cm surrounding the device and 20 c…

Text truncated - open the document above for the full version.

Page 1 of 22 Report No.: HK2012253989-1E FCC TEST REPORT Test report On Behalf of Shenzhen Itian Technology CO.,LTD For Wireless Charger Model No.: F5 FCC ID: 2AUDO-F5 Prepared for : Shenzhen Itian Technology CO.,LTD 5F,Bld. C, Hongde Ind. Park, Shiguan, Lianrun Rd.Dalang St., Longhua District Shenzhen, China Prepared By : Shenzhen HUAK Testing Technology Co., Ltd. 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Fuhai Street, Bao'an District, Shenzhen City, China Date of Test: Dec. 25, 2020 ~Jan. 04, 2021 Date of Report: Jan. 04, 2021 Report Number: HK2012253989-1E Page 2 of 22 Report No.: HK2012253989-1E TEST RESULT CERTIFICATION Applicant’s name ................. : Shenzhen Itian Technology CO.,LTD Address ................................. : 5F,Bld. C, Hongde Ind. Park, Shiguan, Lianrun Rd.Dalang St., Longhua District Shenzhen, China Manufacture's Name ............ : Shenzhen Itian Technology Co., Ltd. Address ................................. : 5th Floor, C Building, Hongde Industrial Park, Shiguan Industrial Area, Tongsheng Community, Lianrun Road, Dalang Street, Longhua District, Shenzhen, China Product description Trade Mark: N/A Product name ........................... : Wireless Charger Model and/or type reference : F5 Standards ............................. : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10: 2013 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen HUAK Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen HUAK Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Date of Test ............................................ : Date (s) of performance of tests ............. : Dec. 25, 2020 ~Jan. 04, 2021 Date of Issue ........................................... : Jan. 04, 2021 Test Result ............................................... : Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou) Page 3 of 22 Report No.: HK2012253989-1E Table of Contents Page 1 . Test Summary 5 1.1 . Test Procedures And Results 5 1.2 . Test Facility 5 1.3 . Measurement Uncertainty 5 2. General Information 6 2.1. General Description of EUT 6 2.2. Carrier Frequency of Channels 7 2.3. Operation of EUT during testing 7 2.4. Description of Test Setup 7 2.5. Measurement Instruments List 8 3. Conducted Emission Test 9 3.1. Block Diagram of Test Setup 9 3.2. Conducted Power Line Emission Limit 9 3.3. Test Procedure 9 4. Occupied Bandwidth 12 4.1. Block Diagram of Test Setup 12 4.2. Rules and specifications 12 4.3. Test Procedure 12 4.4. Test Result 13 5. Radia Ted Emissions 14 5.1. Block Diagram of Test Setup 14 5.2. Rules and specifications 15 5.3. Test Procedure 16 5.4. Test Result 16 6. Antenna Requirement 19 7. Photograph Of Test 20 7.1. Radiated Emission 20 7.2. Conducted Emission 21 8. Photos Of The Eut 22 Page 4 of 22 Report No.: HK2012253989-1E ** Modifited History ** Revison Description Issued Data Remark Revsion 1.0 Initial Test Report Release Jan. 04, 2021 Jason Zhou Page 5 of 22 Report No.: HK2012253989-1E 1. Test Summary 1.1. Test Procedures And Results DESCRIPTION OF TEST SECTION NUMBERRESULT CONDUCTED EMISSIONS TEST 15.207 COMPLIANT RADIATED EMISSION TEST 15.209 COMPLIANT OCCUPIED BANDWIDTH MEASUREMENT 15.215 COMPLIANT ANTENNA REQUIREMENT 15.203 COMPLIANT Note: 1. PASS: Test item meets the requirement. 2. Fail: Test item does not meet the requirement. 3. N/A: Test case does not apply to the test object. 4. The test result judgment is decided by the limit of test standard. 1.2. Test Facility Test Firm : Shenzhen HUAK Testing Technology Co., Ltd. Address 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Fuhai Street, Bao'an District, Shenzhen City, China 1.3. Measurement Uncertainty Measurement Uncertainty Conducted Emission Expanded Uncertainty =2.71dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 4.26dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz)= 3.90dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.28dB, k=2 Page 6 of 22 Report No.: HK2012253989-1E 2. General Information 2.1. General Description of EUT Equipment Wireless Charger Model Name F5 Serial No. N/A Model Difference N/A Trade Mark N/A FCC ID 2AUDO-F5 Antenna Type Coil Antenna Antenna Gain 0dBi Operation frequency 125KHz Number of Channels 1 Modulation Type ASK Power Source Input: 5V/2A, 9V/1.67A, 12V/1.5A Output: 5V/1.0A, 9V/1.20A Power Rating Input: 5V/2A, 9V/1.67A, 12V/1.5A Output: 5V/1.0A, 9V/1.20A Page 7 of 22 Report No.: HK2012253989-1E 2.2. Carrier Frequency of Channels Operation Frequency each of channel Channel Frequency 1 125KHz 2.3. Operation of EUT during testing Operating Mode The mode is used: Transmitting mode 2.4. Description of Test Setup Operation of EUT during testing: AC Plug Adapter information Model: HW-059200CHQ Input: 100-240V, 50-60Hz, 0.5A Output: 5VDC, 2A Mobile phone 1 information Model: iPhone Mobile phone 2 information Model: Samsung S6 The sample was placed (0.8m（30MHz~1GHz）, 0.8m (9KHz~30MHz)) above the ground plane of 3m chamber. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating the turntable, varying antenna height from 1m to 4m in both horizontal and vertical polarizations. The emissions worst-case are shown in Test Results of the following pages. The worst case is X position. Adapter EUT Mobile phone 1 Mobile phone 2 Page 8 of 22 Report No.: HK2012253989-1E 2.5. Measurement Instruments List Item Equipment Manufacturer Model No.Se…

Text truncated - open the document above for the full version.

Conducted Emission Radiated Emissions