2AUJ4JP6STablet for Correctional Use

1 Safety, War ranty & Quick Star t Gui de Model Number: JP6S FCC ID : 2AUJ4JP6S 2 Read this guide carefully before using your device. Reading before using your tablet Reading first - regulatory information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 3 4 Device overview Model Description JP6S Wifi Android Tablet PC 5 Using your device for the first time Charging the tablet You might need to charge the battery before using your device. Insert the DC plug of the power adaptor into the DC port of the tablet pc and plug in the power adaptor to a wall outlet.. Below are battery icons showing different status of the battery. Low battery Fully charged Charging Turning on/off Turn on: Press and hold the Power button until the Android boot on window appears. Turn off: Press and hold the Power button for a few seconds, then tap Power off. Restart: Press and hold the Power button for about 10 seconds to restart. 6 Important safety and handling information Built-in rechargeable battery notice This device contains a Lithium Ion Battery. Caution: The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not disassemble, do not heat above 60 degrees C (140 F), do not crush or puncture the battery, or short external contacts or incinerate. See more information on the Quick Start Guide. Tips for proper care of your tablet battery include: •Don’t overcharge. •Avoid using the tablet when it’s plugged in. •Store your device at the correct (cool) temperature. •Don’t let the battery get all the way to 0% before recharging. •Never use an unauthorized charger. •Avoid physical stress to your tablet. •Turn off your device when charging. Caution about high volume usage Warning: Exposure to loud noise from any source for extended periods of time may affect your hearing. The louder the sound, the less time is required before your hearing could be affected. To protect your hearing: • Limit the amount of time you use headsets or headphones at high volume. • Avoid turning up the volume to block out noisy surroundings. • Turn the volume down if you can’t hear people speaking near you. If you experience hearing discomfort, including the sensation of pressure or fullness in your ears, ringing in your ears or muffled speech, you should stop listening to the device through your headset or headphones and have your hearing checked. To prevent possible hearing damage, do not listen at high volume levels for long periods. 7 Batteries and electrica l and elect ronic equipment marke d with the symbol of a cr ossed-out wheeled bin may not be disposed as unsorted munici pal waste. Batteries and waste of electr ica l and electr onic equipment (WEEE) shall be treated se parately usi ng the co llect ion framework availa ble to cu st omers for the return, recycling, and treatment of batteries and WEEE. When possible, remove and isolate batteries from WEEE prior to placi ng WEEE in the waste co llect ion st ream. Batteries are to be colle ct ed s eparately usi ng the framework available for the return, recycling, and treatment of batteries and acc umulators. Envir onmental , recycli ng, and dis pos al information Important battery and WEEE information FCC compli anc e statement FCC ID: 2AUJ4JP6S Thi s device compl ies with Part 15 of FCC Rul es. Operation is subject to the follo wing two co nditions: (1) this devi ce may not ca use harmful interference, and (2) this device must accept any interference rece ived, incl uding interference that may cause undesired operation. Notice: Changes or modifications not expressly approved by JPay Inc. could void the user's authority to operate the equipment.

F2P21445A Page 1 of 4 Nov. 7, 2019 PHOTOGRAPHS: EXTERNAL Securus Technologies - Model JP6S Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S F2P21445A Page 2 of 4 Nov. 7, 2019 Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S F2P21445A Page 3 of 4 Nov. 7, 2019 Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S F2P21445A Page 4 of 4 Nov. 7, 2019

F2P21445A Page 1 of 3 Nov. 18, 2019 PHOTOGRAPHS: INTERNAL Securus Technologies - Model JP6S Order Number: F2P21445A Client: Securus Technologies Model: JP6S F2P21445A Page 2 of 3 Nov. 18, 2019 Order Number: F2P21445A Client: Securus Technologies Model: JP6S F2P21445A Page 3 of 3 Nov. 18, 2019

© 2020 RF Exposure Lab, LLC This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. 802 N. Twin Oaks Valley Road, Suite 105 • San Marcos, CA 92069 • U.S.A. TEL (760) 471-2100 • FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION Securus Technologies Dates of Test: February 13-14, 2020 4000 International Parkway Test Report Number: SAR.20200205 Carrollton, TX 75007 Revision A This wireless mobile and/or portable device has been shown to be compliant for localized specific absorption rate (SAR) for uncontrolled environment/general exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in IEEE 1528-2013 and IEC 62209-2:2010 (See test report). I attest to the accuracy of the data. All measurements were performed by myself or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. RF Exposure Lab, LLC certifies that no party to this application is subject to a denial of Federal benefits that includes FCC benefits pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Jay M. Moulton Vice President Testing Cert. # 2387.01 FCC ID: 2AUJ4JP6S Model(s): JP6S Test Sample: Engineering Unit Same as Production Serial Number: 5 th Article Equipment Type: Wireless Tablet Classification: Portable Transmitter Next to Body TX Frequency Range: 2412 – 2462 MHz; 5180 – 5250 MHz; 5745 – 5825 MHz Frequency Tolerance: ± 2.5 ppm Maximum RF Output: 2450 MHz (b) – 13.20 dBm, 5250 MHz (a) – 16.00 dBm, 5800 MHz (a) – 16.00 dBm Conducted Signal Modulation: DSSS, OFDM Antenna Type: Internal PIFA Antenna Application Type: Certification FCC Rule Parts: Part 2, 15C, 15E KDB Test Methodology: KDB 447498 D01 v06, KDB 248227 v02r02, KDB 616217 D04 v01r02 Maximum SAR Value: 1.36 W/kg Reported Separation Distance: 0 mm Report Number: SAR.20200205 © 2020 RF Exposure Lab, LLC Page 2 of 82 This report shall not be reproduced except in full without the written approval of RF Exposure Lab, LLC. Table of Contents 1. Introduction ........................................................................................................................ 4 SAR Definition [5] ................................................................................................................... 5 2. SAR Measurement Setup ................................................................................................... 6 Robotic System ...................................................................................................................... 6 System Hardware ................................................................................................................... 6 System Electronics ................................................................................................................. 7 Probe Measurement System .................................................................................................. 7 3. Probe and Dipole Calibration .............................................................................................15 4. Phantom & Simulating Tissue Specifications .....................................................................16 Head & Body Simulating Mixture Characterization ................................................................16 5. ANSI/IEEE C95.1 – 1992 RF Exposure Limits [2] ..............................................................17 Uncontrolled Environment .....................................................................................................17 Controlled Environment .........................................................................................................17 6. Measurement Uncertainty .................................................................................................18 7. System Validation..............................................................................................................19 Tissue Verification .................................................................................................................19 Test System Verification ........................................................................................................19 8. SAR Test Data Summary ..................................................................................................20 Procedures Used To Establish Test Signal ...........................................................................20 Device Test Condition ...........................................................................................................20 SAR Data Summary – 2450 MHz Body 802.11b ...................................................................26 SAR Data Summary – 5250 MHz Body 802.11a ...................................................................27 SAR Data Summary – 5800 MHz Body 802.11n ...................................................................28 9. Test Equipment List ...........................................................................................................29 10. Conclusion ....................................................................................................................30 11. References ....................................................................................................................31 Appendix A – S ystem Validation Plots and Data .......................................................................32 Appendix B – SAR Test Data Plots ...........................................................................................40 Appendix C – SAR Test Setup Photos ......................................................................................44 Appendix D – Probe Calibration Data Sheets ...........................…

Text truncated - open the document above for the full version.

090215 Report Number: F2P21445A-02E Page 1 of 103 Issue Date: Feb. 10, 2020 F2 Labs 16740 Peters Road Middlefield, Ohio 44062 United States of America www.f2labs.com CERTIFICATION TEST REPORT Manufacturer: Securus Technologies 4000 International Parkway Carrollton, Texas 75007 USA Applicant: Same as Above Product Description: 802.11ac Dual Band Module Product Name: JP6S Product Description: 7” Lithium Capacitive Touch Tablet for Inmates Model: JP6S FCC ID: 2AUJ4JP6S Testing Commenced: Aug. 15, 2019 Testing Ended: Feb. 10, 2020 Summary of Test Results: In Compliance, with Modifications The EUT complies with the EMC requirements when manufactured identically as the unit tested in this report, including any required modifications. Any changes to the design or build of this unit subsequent to this testing may deem it non-compliant. Rule(s): • FCC Part 15 Subpart E – Unlicensed National Information Infrastructure Devices, Section 15.407 General technical requirements • FCC15.207 - Conducted Limits Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 090215 Report Number: F2P21445A-02E Page 2 of 103 Issue Date: Feb. 10, 2020 Evaluation Conducted by: Julius Chiller, EMC/Wireless Engineer Report Reviewed by: Ken Littell, Director of EMC & Wireless Operations F2 Labs F2 Labs F2 Labs 26501 Ridge Road 16740 Peters Road 8583 Zionsville Road Damascus, MD 20872 Middlefield, OH 44062 Indianapolis, IN 46268 Ph 301.253.4500 Ph 440.632.5541 Ph 317.610.0611 This test report may be reproduced in full; partial reproduction only may be made with the written consent of F2 Labs. The results in this report apply only to the equipment tested. Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 090215 Report Number: F2P21445A-02E Page 3 of 103 Issue Date: Feb. 10, 2020 TABLE OF CONTENTS Section Title Page 1 ADMINISTRATIVE INFORMATION 4 2 SUMMARY OF TEST RESULTS/MODIFICATIONS 7 3 TABLE OF MEASURED RESULTS 8 4 ENGINEERING STATEMENT 9 5 EUT INFORMATION AND DATA 10 6 LIST OF MEASUREMENT INSTRUMENTATION 12 7 OCCUPIED BANDWIDTH 13 8 OUTPUT POWER 24 9 POWER SPECTRAL DENSITY 30 10 RADIATED SPURIOUS EMISSIONS 36 11 CONDUCTED SPURIOUS EMISSIONS 51 12 VOLTAGE VARIATIONS 84 13 CONDUCTED EMISSIONS 95 14 PHOTOGRAPHS 100 Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 090215 Report Number: F2P21445A-02E Page 4 of 103 Issue Date: Feb. 10, 2020 1 ADMINISTRATIVE INFORMATION 1.1 Measurement Location: F2 Labs in Middlefield, Ohio. Site description and attenuation data are on file with the FCC's Sampling and Measurement Branch at the FCC Laboratory in Columbia, MD. 1.2 Measurement Procedure: All measurements were performed according to ANSI C63.10:2013 and recommended FCC procedure of measurement of NII operating under Section 15.407 and in KDB789033. A list of the measurement equipment can be found in Section 6. Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 090215 Report Number: F2P21445A-02E Page 5 of 103 Issue Date: Feb. 10, 2020 1.3 Uncertainty Budget: The uncertainty in EMC measurements arises from several factors which affect the results, some associated with environmental conditions in the measurement room, the test equipment being used, and the measurement techniques adopted. The measurement uncertainty budgets detailed below are calculated from the test and calibration data and are expressed with a 95% confidence factor using a coverage factor of k=2. The Uncertainty for a laboratory are referred to as Ulab. For Radiated and Conducted Emissions, the Expanded Uncertainty is compared to the Ucispr values to determine if a specific margin is required to deem compliance. Ulab Ucispr If Ulab is less than or equal to Ucispr, then: • compliance is deemed to occur if no measured disturbance exceeds the disturbance limit; • non-compliance is deemed to occur if any measured disturbance exceeds the disturbance limit. If Ulab is greater than Ucispr in table 1, then: • compliance is deemed to occur if no measured disturbance, increased by (Ulab – Ucispr), exceeds the disturbance limit; • non-compliance is deemed to occur if any measured disturbance, increased by (Ulab – Ucispr), exceeds the disturbance limit. Note: Only measurements listed in the tables above that relate to tests included in this Test Report are applicable. Measurement Range Combined Uncertainty Expanded Uncertainty Radiated Emissions <1 GHz @ 3m 2.54 5.07dB Radiated Emissions <1 GHz @ 10m 2.55 5.09dB Radiated Emissions 1 GHz to 2.7 GHz 1.81 3.62dB Radiated Emissions 2.7 GHz to 18 GHz 1.55 3.10dB AC Power Line Conducted Emissions, 150kHz to 30 MHz 1.38 2.76dB AC Power Line Conducted Emissions, 9kHz to 150kHz 1.66 3.32dB Measurement Range Expanded Uncertainty Radiated Emissions <1 GHz @ 3m 5.2dB Radiated Emissions <1 GHz @ 10m 5.2dB Radiated Emissions 1 GHz to 2.7 GHz Under Consideration Radiated Emissions 2.7 GHz to 18 GHz Under Consideration AC Power Line Conducted Emissions, 150kHz to 30 MHz 3.6dB AC Power Line Conducted Emissions, 9kHz to 150kHz 4.0dB Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 090215 Report Number: F2P21445A-02E Page 6 of 103 Issue Date: Feb. 10, 2020 1.4 Document History Document Number Description Issue Date Approved By F2P21445-02E First Issue Feb. 10, 2020 K. Littell Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 090215 Report Number: F2P21445A-02E Page 7 of 103 Issue Date: Feb. 10, 2020 2 SUMMARY OF TEST RESULTS Test Name Standard(s) Results Radiated Spurious Emissions CFR 47 Part 15.205 / KDB789033 Complies Occupied Bandwidth CFR 47 Part 15.407(e) / Part 15.209 / KDB789033 Complies Output Power CFR 47 Part 15.407(a)(1)(iv) / Part 15.407(a)(3) / KDB789033 Complies Power Spectral Density CFR 47 Part 15.407(a)(1)(iv) / Part 15.407(a)(3) / KDB789033 Complies Conducted Spurious Emissions CFR 47 Part 15.407(b)(1,4) Complies Voltage Variations CFR 47 Part 15.31(e) Complies Conducted Emissions CFR 47 Part 15.207(a) Complies Modifications…

Text truncated - open the document above for the full version.

051816 Report Number: F2P21445A-03E Page 1 of 95 Issue Date: Feb. 5, 2020 F2 Labs 16740 Peters Road Middlefield, Ohio 44062 United States of America www.f2labs.com CERTIFICATION TEST REPORT Manufacturer: Securus Technologies 4000 International Parkway Carrollton, Texas 75007 USA Applicant: Same As Above Product Name: JP6S Product Description: 7” Lithium Capacitive Touch Tablet for Inmates Model: JP6S FCC ID: 2AUJ4JP6S Testing Commenced: Aug. 14, 2019 Testing Ended: Feb. 5, 2020 Summary of Test Results: In Compliance, with Modifications The EUT complies with the EMC requirements when manufactured identically as the unit tested in this report, including any required modifications and/or manufacturer’s statement. Any changes to the design or build of this unit subsequent to this testing may deem it non-compliant. Rule(s): • FCC Part 15 Subpart E – Unlicensed National Information Infrastructure Devices, Section 15.407 General technical requirements Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 051816 Report Number: F2P21445A-03E Page 2 of 95 Issue Date: Feb. 5, 2020 Evaluation Conducted by: Julius Chiller, EMC/Wireless Engineer Report Reviewed by: Ken Littell, Director of EMC & Wireless Operations F2 Labs F2 Labs F2 Labs 26501 Ridge Road 16740 Peters Road 8583 Zionsville Road Damascus, MD 20872 Middlefield, OH 44062 Indianapolis, IN 46268 Ph 301.253.4500 Ph 440.632.5541 Ph 317.610.0611 This test report may be reproduced in full; partial reproduction only may be made with the written consent of F2 Labs. The results in this report apply only to the equipment tested. Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 051816 Report Number: F2P21445A-03E Page 3 of 95 Issue Date: Feb. 5, 2020 TABLE OF CONTENTS Section Title Page 1 ADMINISTRATIVE INFORMATION 4 2 SUMMARY OF TEST RESULTS/MODIFICATIONS 5 3 TABLE OF MEASURED RESULTS 6 4 ENGINEERING STATEMENT 7 5 EUT INFORMATION AND DATA 8 6 LIST OF MEASUREMENT INSTRUMENTATION 9 7 OCCUPIED BANDWIDTH 10 8 CONDUCTED OUTPUT POWER 16 9 VOLTAGE VARIATIONS 22 10 CONDUCTED SPURIOUS EMISSIONS 33 11 RADIATED SPURIOUS EMISSIONS 67 12 PEAK POWER SPECTRAL DENSITY (PSD) 87 13 PHOTOGRAPHS 93 Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 051816 Report Number: F2P21445A-03E Page 4 of 95 Issue Date: Feb. 5, 2020 1 ADMINISTRATIVE INFORMATION 1.1 Measurement Location: F2 Labs in Middlefield, Ohio. Site description and attenuation data are on file with the FCC's Sampling and Measurement Branch at the FCC Laboratory in Columbia, MD. 1.2 Measurement Procedure: All measurements were performed according to ANSI C63.10:2013 and recommended FCC procedure of measurement of NII operating under Section 15.407 and in KDB789033. A list of the measurement equipment can be found in Section 6. 1.3 Uncertainty Budget: The uncertainty in EMC measurements arises from several factors which affect the results, some associated with environmental conditions in the measurement room, the test equipment being used and the measurement techniques adopted. The measurement uncertainty budgets detailed below are calculated from the test and calibration data, and are expressed with a 95% confidence factor. Note: Only measurements listed below which relate to tests included in this Test Report are applicable to it. This Uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 1.4 Document History Document Number Description Issue Date Approved By F2P21445A-03E First Issue Feb. 5, 2020 K. Littell Measurement Range Expanded Uncertainty Combined Uncertainly Radiated Emissions <1 GHz @ 3m ±5.07dB ±2.54 Radiated Emissions <1 GHz @10m ±5.09dB ±2.55 Radiated Emissions 1 GHz to 2.7 GHz ±3.62dB ±1.81 Radiated Emissions 2.7 GHz to 18 GHz ±3.10dB ±1.55 AC Power Line Conducted Emissions, 150kHz to 30 MHz ±2.76dB ±1.38 Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 051816 Report Number: F2P21445A-03E Page 5 of 95 Issue Date: Feb. 5, 2020 2 SUMMARY OF TEST RESULTS Test Name Standard(s) Results Radiated Spurious Emissions CFR 47 Part 15.205 / KDB789033 Complies Occupied Bandwidth CFR 47 Part 15.407(e) / Part 15.209 / KDB789033 Complies Output Power CFR 47 Part 15.407(a)(1)(iv) / Part 15.407(a)(3) / KDB789033 Complies Power Spectral Density CFR 47 Part 15.407(a)(1)(iv) / Part 15.407(a)(3) / KDB789033 Complies Conducted Spurious Emissions CFR 47 Part 15.407(b)(1,4) Complies Voltage Variations CFR 47 Part 15.31(e) Complies Modifications Made to the Equipment RF Power was reduced to 15dBm setting to reduce Power Spectral Density to passing level. Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 051816 Report Number: F2P21445A-03E Page 6 of 95 Issue Date: Feb. 5, 2020 3 TABLE OF MEASURED RESULTS Wi-Fi, 5.7 GHz Test Low Channel OFDM 20M: 5745 MHz OFDM 40M: 5755 Mid Channel OFDM 20M: 5785 MHz High Channel OFDM 20M: 5825 MHz OFDM 40M: 5795 MHz Conducted Output Power OFDM, 20M 54mbps 25.06mW / 13.99dBm 23.33mW / 13.68dBm 28.77mW / 14.59dBm OFDM 40M 54mpbs 23.66mW / 13.74dBm -- 24.21mW / 13.84dBm Conducted Output Power Limit 1 Watt / 30dBm 1 Watt / 30dBm 1 Watt / 30dBm E.I.R.P. with 2dBi Integral Antenna OFDM 20M 39.72mW / 15.99dBm 36.98mW / 15.68dBm 45.60mW / 16.59dBm OFDM 40M 37.49mW / 15.74dBm -- 38.37mW / 15.84dBm E.I.R.P. Limit 4000mW / 36dBm 4000mW / 36dBm 4000mW / 36dBm Peak Power Spectral Density OFDM 20M 2.02dBm 2.47dBm 2.62dBm OFDM 40M -1.44dBm -- -1.48dBm Peak Power Spectral Density Limit 8 dBm 8 dBm 8 dBm -6dB Occupied Bandwidth 16.445 MHz 16.427 MHz 16.429 MHz 36.395 -- 36.375 -6dB Occupied Bandwidth Limit ≥ 500kHz ≥ 500kHz ≥ 500kHz Voltage Variations OFDM 20M 93.5V 11.26dBm 11.06dBm 12.31dBm 126.5V 12.38dBm 11.93dBm 13.15dBm OFDM 40M 93.5V 8.51dBm -- 8.53dBm 126.5V 8.76dBm -- 8.83dBm Limit 1W 30dBm 1W 30dBm 1W 30dBm Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S 051816 Report Number: F2P21445A-03E Page 7 of 95 Issue Date:…

Text truncated - open the document above for the full version.

F2P21445A Page 1 of 3 Nov. 7, 2019 PHOTOGRAPHS: TEST SETUP Securus Technologies - Model JP6S Radiated Spurious Emission, Less Than 30 MHz Radiated Spurious Emission, 30 MHz to 1000 MHz Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S F2P21445A Page 2 of 3 Nov. 7, 2019 Radiated Spurious Emission, 1 GHz to 18 GHz Radiated Spurious Emission, 18 GHz to 26 GHz Order Number: F2P21445A Applicant: Securus Technologies Model: JP6S F2P21445A Page 3 of 3 Nov. 7, 2019 Conducted Output Power, Peak Power Spectral Density, Occupied Bandwidth, and Conducted Spurious Emissions Conducted Emissions