2AUR5-ESX1Electric scooter

Electric scooter Instruction Manual ESX1 1. Product description Throttle Power switch (control panel) Brake lever Bell Front light Folding quick release charging port 口 Tail light Drum brake Kickstand Motor Screws L screwdriver Charger 2.Assemble the vehicle 1. Put the handle bar set into 2. Fasten with the four screws (included). the big tube 3.Folding operation 1. How to unfold your scooter 2. How to fold up your scooter (1). Hold the handle bar with one hand (2).push the folded hook with another hand (3). then lift the handlebar upward (4). Hold the tube with one hand, lift and press the quick-release lever by another hand 1.Hold the tube with one hand. 2.Use your thumb and push down the red safety button 3.Loosen the quick-release lever 4. Put down the tube and hook on the rear wheel fender 4.Display Operation Speed display Power display ON-OFF headlight Tail light 1. power on/ power off Operation (1) Press the button for 3 seconds to start up, the speed is displayed as 00, and the LED light is on. (2) Press the ON-OFF button again for 3 seconds to shut down. 2. Light operation (1) Touch the button lightly, the headlight and taillight will light up. Touch the button again, the headlight and taillight will turn off. (2) Press the brake lever, the taillight will flash 3. change the speed modes (1) when the power on, the speed is set up on maximum speed: 25KM/H. (2) The second mode is 18KM/H). Press the button twice to switch speed modes. 5.Get the APP 1. Installation and operation instructions of E-SCOOTER APP （1） Scanning below QR-code. （2） Enter the download web page and download the app.. （3） Install App-----FLSTools 2. App operation (1) open the app FLST00ls. (2) Click “connect” on the top right icon to get connected the bluetooth with your e -scooter. (3) After connection is successful, the mobile panel will display the Bluetooth name, display version and controller version. (4) Click unlock to unlock e-scooter. Click lock to lock escooter. (5) Touch turn on to turn on the lights, touch turn off to turn off the lights. (6) Click set gear,setting the gear of E-SCOOTER (7) Click on the real-time data to display the real-time speed and power. (8) Click Clear mileage to clear the vehicle mileage information. (9) Click on the constant speed cruise,and the speed will be locked when the fixed staying for 8 seconds,the fixed speed can be released by using brakes or turning handles. (10)Click start mode to set zero start and non-zero start. 6.Riding Safety first When we ride, we need to wear protective devices such as helmet knee pads, elbow pads. Kick At the beginning of the ride， one foot is on the deck and another foot slightly kick the floor backward. Start freely Press the throttle to accelerate, press the brake to decelerate and stop. 7.Charging Connect the charger to the charging port. When the charger shows green light, it means full of charge Normal charging when the charger indicator is red Warning Please do not attempt to charge if the charging interface or electrical appliance is wet. Only use the special charger provided by the supplier for charging. The ambient temperature must be 32-104 degrees F (0-40 C) during charging Beyond or under this temperature, the battery can not be charged successfully. Warning 1. Wear helmet, shoes, knee pads, wrist pads and strong protective clothing when riding. The maximum loading capacity is 120KG. 2. Do not ride in rain or wetlands 3. Do not drive on speed bumps or uneven ground at high speed 4. Do not drive on public roads or highways 5. Don't press the accelerator while walking 6. Slow down when turning 7. Do not use one scooter for two or more people at the same time 8. Do not ride up or down stairs. Do not store or expose to high temperature and humidity 9. Do not use E-Scooter, in case of damage, 10. This appliance can be used by aged from 16 years and above and persons with reduced p hysical, sensory or mental capabilities or lack of experience and knowledge if they have been gi ven supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. 11. You must read the manual carefully before using E-Scooter. 12. Only use specified charger in the manual for charging 13. Do not ride above 2000 M in height. 14. Children shall not play with the appliance. Cleaning and user maintenance shall not be mad e by children without supervision Specification: Input Power：350W Battery:36V 5Ah Charging time 3.5-4 hours Range: 25km Net weight: about 14.0kg App: iOS and Android Connectivity: Bluetooth and cellular IP Rating: IPX4 water-resistant Lights: Front and Rear LED llights Brake system: Electronic brake + Mechanical Drum Brake Tire: 8.5 " Semi solid pneumatic Maximum speed: 25km /h Climbing ability: 8 degree Weight limit: 120KG Suitable temperature 14-104 ° f (- 10-40 ° C) Operating temperature 14-104 ° f (- 10-40 ° C) Charger Parameters Input voltage 100-240AC Output voltage 42VDC Output current 2.0 amps Charger model: CP4220 (Coming Data Co., Ltd.) * shown in the range of the maximum range ˴ climbing ability data such as in the actual ride ˴ will be affected by the rider weight ˴ factors such as road ˴ will be less than or more than marked. Serial Number: This serial number will be your maintenance voucher, do not tear. Maintenance 1. Before cleaning the product, be sure to turn off the switch and disconnect the power supply. 2. Please clean the product in time after use. 3. The electric scooter can be wiped with a wet cloth. Do not put the body into water or other liquids, nor wash it under water or other liquids. 4. This product should be stored in a dry place and avoid direct ultraviolet radiation. 5. Before storing the product, make sure it is clean and dry. If you experience problems related to riding, maintenance and safety, or if your electric vehicle appears problems, please contact us in further. Contact information: Manufacturer：HL Corp Shenzhen Address：The 3rd Industrial Park , Bitou Vill…

Text truncated - open the document above for the full version.

[2020-01-08] Federal Communications Commission 445 12 th Street SW Washington, DC 20554 Subject: Limited Agency Agreement HL CORP(SHEN ZHEN) FCC ID: 2AUR5-ESX1 To Whom It May Concern: We, HL CORP(SHEN ZHEN) hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number (2AUR5-ESX1) under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is (2020-01-08). The Limited Agency Agreement expires until further notice, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, [Signature] HL CORP(SHEN ZHEN) Contact person: Zheng fengchun

Jan. 06, 2020 Federal Communication Commission Authorization and Evaluation Division FCC ID: 2AUR5-ESX1 Re: Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the applicant hereby requests confidential treatment of information applied this application as outlined below: 1: Block Diagram 2: Schematics 3: Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rules 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, HL CORP(SHEN ZHEN) Contact person: Zheng fengchun

External Photos TOTAL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT VIEW OF EUT(PORT)

FCC ID Label Location FCC ID: 2AUR5-ESX1 Brand Name : MÜVU MoDEL NAME: ESX1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Internal Photos OPEN VIEW OF EUT-1 OPEN VIEW OF EUT-2 OPEN VIEW OF EUT-3 OPEN VIEW OF EUT-4 OPEN VIEW OF EUT-5 VIEW OF BATTERY INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 INTERNAL VIEW OF EUT-4 BT Antenna INTERNAL VIEW OF EUT-5 Adapter

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description Electric scooter Model Name ESX1 FCC ID 2AUR5-ESX1 2. EVALUATION METHOD According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 3. CALCULATION P t = 0.976dBm=1.25mW The value of the Maximum output power P t is referred to the test report of the CFR47 §15.247. The result for RF exposure evaluation SAR=(1.25mW /5mm) .[√2.480(GHz)]= 0.39<3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. 4. CONCLUSION The SAR evaluation is not required.

Page 1 of 50 FCC Test Report Report No.: AGC08696191006FE02 FCC ID : 2AUR5-ESX1 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Electric scooter BRAND NAME : ORBO MODEL NAME : ESX1 APPLICANT : HL CORP(SHEN ZHEN) DATE OF ISSUE : Jan. 06, 2020 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC08696191006FE02 Page 2 of 50 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jan. 06, 2020 Valid Initial Release Report No.: AGC08696191006FE02 Page 3 of 50 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE ............................................................................................................... 5 2.GENERAL INFORMATION ............................................................................................................................. 6 2.1PRODUCT DESCRIPTION ...................................................................................................................... 6 2.2. TABLE OF CARRIER FREQUENCYS ................................................................................................... 6 2.3 RELATED SUBMITTAL(S)/GRANT(S) .................................................................................................... 7 2.4TEST METHODOLOGY ........................................................................................................................... 7 2.5 SPECIAL ACCESSORIES ...................................................................................................................... 7 2.6 EQUIPMENT MODIFICATIONS .............................................................................................................. 7 3. MEASUREMENT UNCERTAINTY ................................................................................................................. 8 4. DESCRIPTION OF TEST MODES ................................................................................................................. 9 5. SYSTEM TEST CONFIGURATION ............................................................................................................. 10 5.1 CONFIGURATION OF TESTED SYSTEM ............................................................................................ 10 5.2 EQUIPMENT USED IN TESTED SYSTEM ........................................................................................... 10 5.3. SUMMARY OF TEST RESULTS .......................................................................................................... 10 6. TEST FACILITY ............................................................................................................................................ 11 7. PEAK OUTPUT POWER ............................................................................................................................. 12 7.1. MEASUREMENT PROCEDURE .......................................................................................................... 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................. 12 7.3. LIMITS AND MEASUREMENT RESULT .............................................................................................. 13 8. 6 DB BANDWIDTH ...................................................................................................................................... 15 8.1. MEASUREMENT PROCEDURE .......................................................................................................... 15 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................. 15 8.3. LIMITS AND MEASUREMENT RESULTS ........................................................................................... 15 9. CONDUCTED SPURIOUS EMISSION ........................................................................................................ 17 9.1. MEASUREMENT PROCEDURE .......................................................................................................... 17 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................. 17 9.3. MEASUREMENT EQUIPMENT USED ................................................................................................ 17 9.4. LIMITS AND MEASUREMENT RESULT .............................................................................................. 17 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ....................................................... 22 10.1 MEASUREMENT PROCEDURE ......................................................................................................... 22 10.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 22 10.3 MEASUREMENT EQUIPMENT USED ............................................................................................... 22 10.4 LIMITS AND MEASUREMENT RESULT ............................................................................................. 22 11. RADIATED EMISSION ............................................................................................................................... 24 11.1. MEASUREMENT PROCEDURE ........................................................................................................ 24 11.2. TEST SETUP ..................................................................................................................................... 25 11.3. LIMITS AND MEASUREMENT RESULT ............................................................................................ 26 11.4. TEST RESULT ................................................................................................................................... 26 12. FCC LINE CONDUCTED …

Text truncated - open the document above for the full version.

Test Setup Photos RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ CONDUCTED TEST SETUP