2AVED-FRX-M79AU-21802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module

FRX-M79AU-21 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module Specification Module Name: FRX-M79AU-21 Module Type: 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module Revision: V1.0 Customer Approval: Company: Title: Signature: Date: Title: Signature: Date: Revision History Revision Summary Release Date 0.1 Initial release 2021-02-24 1.Introduction FRX-M79AU-21 is ahighlyintegratedDual-band WLAN+ Bluetooth v5.2Combomodule.It combines a 2T2R Dual-band WLAN subsystem and a Bluetooth v5.2 subsystem which features dual BT controllers.This modulecompatible IEEE 802.11a/b/g/n/ac/ax standard and provides the maximum PHYrate up to 1200Mbps, it supports BT / BLE dual mode with BT v5.2/v4.2/v2.1 compliant, offering feature-rich wireless connectivity at high standards, and delivering reliable, cost-effective throughput from an extended distance. 1.1 Features Operating Frequency: 2.4~2.4835GHz or 5.15~5.85GHz WLAN features: Support Dual-band 2T2R mode with 20/40/80Mhz bandwidth Support MU-MIMO RX, MU-OFDMA TX/RX Support TX/RX Beamformer Support DBDC (dual band dual concurrent) Bluetooth features: Support BT Classic / BT Low Energy dual mode Contains dual BT controllers 1.2 General Specifications Module Name 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module Chipset MT7921AUN WLAN Standard IEEE802.11a/b/g/n/ac/ax BT Specification Bluetooth Core Specification v5.2/4.2/2.1 Host Interface USB3.0/USB2.0 for WLAN;USB2.0 for Bluetooth (Reserved UART interface for BT) Antenna IPEX / MHF-1 connector for external WLAN antenna; Half hole PADs for external BT antenna (Reserved IPEX connector for BT0) Dimension 27.0*17.8*2.5mm (L*W*H) Power Supply DC 3.3V±0.2V @ 1800 mA (Max) Operation Temperature -20°C to +70°C Operation Humidity 10% to 95% RH (Non-Condensing) 2.Pin Assignments (TOP View) 2.1 Pin Definition No. Pin Name Type Level Module Pin Description 1 GND RF RF Ground for WLAN_ANT1 2 NC RF NC（Reserved 2.4G / 5G RFPAD for WLAN_ANT1） 3 GND RF RF Ground for WLAN_ANT1 4 GND RF RF Ground for WLAN_ANT0 5 NC RF NC （ Reserved 2.4G / 5G RF PAD for WLAN_ANT0） 6 GND RF RF Ground for WLAN_ANT0 7 GND RF RF Ground for BT_ANT1 8 BT_RF1 RF RF PAD for BT_ANT1 9 GPIO / UART_TXD I/O 3.3V Function1 、 GPIO15 ， output shall not be used as input ； Function2 、 UART TXD output ； Function3、BT Host Interface Select Boot strap： 0 ： USB (internal pull Low by 10K) 1：UART If not used，this Pin can be left floating . 10 GND P Ground for Power and I/O 11 GPIO / UART_RXD I/O 3.3V 1 、 GPIO14 ， I/O ； 2、UART RXD input . If not used，this Pin can be left floating . 12 GPIO / WL_Wake_Host I/O 3.3V 1 、 GPIO1 ， I/O ； 2 、 Wlan Wake up Host ， Active Low output ， internal pull high by 10K resistor. If not used ， this Pin can be left floating . 13 GND P Ground for Power and I/O 14 SSTX- AO USB3.0 SuperSpeed Device Interface TX differential pair， DC blocked output（to connect USB 3.0 Host“ SSRX- ”） If USB3.0 is not used ， this Pin can be left floating . 15 SSTX+ AO USB3.0 SuperSpeed Device Interface TX differential pair， DC blocked output（to connect USB 3.0 Host“ SSRX+ ”） If USB3.0 is not used ， this Pin can be left floating . 16 SSRX- AI USB3.0 SuperSpeed Device Interface RX differential pair （to connect USB 3.0 Host“SSTX-”） If USB3.0 is not used，this Pin can be left floating . 17 SSRX+ AI USB3.0 SuperSpeed Device Interface RX differential pair （to connect USB 3.0 Host“ SSTX+ ”） If USB3.0 is not used ， this Pin can be left floating . 18 GND P Ground for Power and I/O 19 HSD+ A I/O USB2.0 HighSpeed Device Interfacedifferential pair （to connect USB 2.0 Host“HSD+”） 20 HSD- AI/O USB2.0 HighSpeed Device Interfacedifferential pair （to connect USB 2.0 Host“HSD-”） 21 VDD33 P DC 3.3V power supply 22 Reset I/O 3.3V Reset input，this Pin can externally shutdown/reset theModule，Active Low, internal pull high by 10K resistor. If not used，this Pin can be left floating . 23 GPIO / BT_Wake_Host I/O 3.3V 1 、 GPIO0 ， I/O ； 2 、 BT LE Wake up Host ， Active Low output ， internal pull high by 10K resistor. If not used ， this Pin can be left floating . 24 GPIO / UART_RTS I/O 3.3V 1 、 GPIO11 ， output ， shall not be used as input ； 2 、 UART RTS output ； 3、USB FrequencySelect_Boot strap： 0 ： USB 5G Mode 1：USB 2.5G Mode (internal weak pull Low) If not used，this Pin can be left floating . 25 GPIO / UART_CTS I/O 3.3V 1 、 GPIO12 ， I/O ； 2 、 UART RTS input . If not used ， this Pin can be left floating . 26~28 NC / NC 29 GND RF RF Ground for BT_ANT0 30 BT_RF0 RF RF PAD for BT_ANT0 31 GND RF RF Ground for BT_ANT0 32~59 GND P Optional ground pads of heatsink,can be left floating. P1 WLAN_RF1 RF IPEX connector for 2.4G / 5G RF to WLAN_ANT1 P2 NC RF NC（Reserved IPEX connector PAD for BT_ANT0） P3 WLAN_RF0 RF IPEX connector for 2.4G / 5G RF to WLAN_ANT0 P: Power;I/O: In/Output; A I/O: AnalogIn/Output;RF: Analog RF Port; 3.Electrical and Thermal Specifications 3.1 Recommended Operating Conditions Parameters Min Typ Max Units Ambient Operating Temperature -2025 70 °C External Antenna VSWR 1.7 2 / Supply Voltage VDD33 3.1 3.3 3.5 V 3.2 Digital I/O DC Specifications Symbol Parameter Min Typ Max Units VIH Input High Voltage VDD33*0.625 -- VDD33+0.3 V VIL Input Low Voltage -0.3-- VDD33*0.25 V VOH Output High Voltage VDD33*0.75 -- VDD33+0.3 V VOL Output Low Voltage -0.3-- VDD33*0.125 V 3.3 Current Consumption Conditions : VDD33=3.3V ; Ta:25°C Use Case VDD33 Current (average) Typ Max Units WLANUnassociated (Linux Driver,BT disable) TBD TBD mA 2.4G HE_SU 40MHz RX Listen (Linux Driver, BT disable) TBD TBD mA 5G HE_SU 80MHz RX Listen (Linux Driver, BT disable) TBD TBD mA 2.4G HT20 MCS8 TX@19dBm (2TX RF test) TBD TBD mA 2.4G HE_SU 40MHz MCS11 TX@14dBm (2TX RF test) TBD TBD mA 5G HT20 MCS8 [email protected] (2TX RF test) TBD TBD mA 5G HE_SU 80MHz MCS11 [email protected](2TX RF test) TBD TBD mA 2.4G HE_SU 40MHz MCS11RX Active (2RX RF test) TBD TBD mA 5G HE_SU 80MHz MCS11 RX Active (2RX RF test) TBD TBD mA Bluetooth Unassociated (Linux Driver, WLAN disable) …

Text truncated - open the document above for the full version.

FCC Software Configuration Control Declaration Rev1.1 Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd FCC Software Configuration Control Declaration Date: November 11, 2022 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Product/ Model Number: 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module / 2AVED-FRX-M79AU-21 Regarding FCC Country Code Selection guidelines identified in KDB 594280. “All applications for equipment authorization for transmitters that can have radio parameters, or other technical parameters, reported to the Commission set by software must have an attestation indicating that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified.” We declare that no third party will have software, or configuration control, to program the device out of compliance of the technical rules under which it has been certified. Name: Haiyun Peng Date: 2022/11/09 Title: sales director Signature of applicant

Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Agent Authorization Company: Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Address: 302, Building 6, no.4 Zhongxing road, Zhangge community, Fucheng street, Longhua district, Shenzhen, Guangdong,P.R. China Product Name: 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module Trade Mark: N/A Model Number(s): FRX-M79AU-21 FCC ID: 2AVED-FRX-M79AU-21 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2022-11-09 Name: Haiyun Peng Title: sales director Company: Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd

Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd FCC Modular Approval Request Rev 3.0 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Subject; Limited Module Approval Request Letter Company name: 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module FCC ID: 2AVED-FRX-M79AU-21 Dear Sir/Madam, This letter includes the FCC application requirements for Modular Transmitter Approval Request for;- FCC KDB 996369 D01 ‘Module Certification Guide v02; and FCC KDB 996369 D03 OEM Manual v01 In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 ‘Module Equip Auth Guide v02’. FCC ID: 2AVED-FRX-M79AU-21 has been examined against the following requirements. Requirement per 15.212 and KDB 996369 D01 Explanation from Grantee (do not write yes/no, but explain why product complies/how it is achieved) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. Yes the module with a shield. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal. Yes The module must contain power supply regulation on the module. The modular has an onboard 3.3V regulator(integrated in MT7921A). The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). The modular contain a unique antenna connector, and be marketed and operated only with specific antenna(s) of Section 15.204(c),Maximum Antenna Gain is 5dBi. The module must demonstrate compliance in a stand-alone configuration. The modular was tested in a standalone configuration apart from host units. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748). The modular has its own FCC ID number. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. Yes Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd FCC Modular Approval Request Rev 3.0 The module must comply with RF exposure requirements Yes, RF cexposure evaluation performed at 20cm. Integration Instructions for host product manufacturers The following items are submitted in support of application for Modular Transmitter FCC ID as noted above as required by the FCC KDB 996369 D03 OEM Manual v01. These items are provided as integration instructions for host product manufacturers (e.g., OEM instruction manual) to use when integrating a module in a host product. Any requirements that are not applicable to the Module are as indicated below. Summary of requirements and Checklist. Refer to the KDB for description of the complete requirements; KDB Ref Sect Requirements of KDB 996369 D03 User Manual Page Number reference 2.2 List of applicable FCC rules Page 21 2.3 Summarize the specific operational use conditions Page 21 2.4 Limited module procedures Page 21 2.5 Trace antenna designs Page 21 2.6 RF exposure considerations Page 21 2.7 Antennas Page 21 2.8 Label and compliance information Page 21 2.9 Information on test modes and additional testing requirements Page 21 2.10 Additional testing, Part 15 Subpart B disclaimer Page 21 Name: Haiyun Peng Date: 2022-11-09 Title: sales director Signature of applicant

Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2022-11-09 Subject; Request for Confidentiality FCC ID: 2AVED-FRX-M79AU-21 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM Software Security Requirements In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name / Title: Haiyun Peng / sales director Company: Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Address: 302, Building 6, no.4 Zhongxing road, Zhangge community, Fucheng street, Longhua district, Shenzhen Guangdong,P.R., China, 518000 Phone: 13662644686 Fax: 0755-28164675 E-Mail: [email protected]

FCC ID: 2AVED-FRX-M79AU-21 Fig. 1 Fig. 2 WLAN Antenna 1 WLAN Antenna 0 BT Antenna 2 FCC ID: 2AVED-FRX-M79AU-21 Fig. 3 Fig. 4

_____________________________________________________________________________________________________ LABEL AND LOCATION (Size: L2.0cm x 1.0cm) Label Location Model : FRX-M79AU-21 FCC ID: 2AVED-FRX-M79AU-21

FCC ID: 2AVED-FRX-M79AU-21 Fig. 1 Fig. 2 FCC ID: 2AVED-FRX-M79AU-21 Fig. 3

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong RF Exposure evaluation Report Reference No. ................. : FCC ID. ......................................... : GTS20221010004-1-6 2AVED-FRX-M79AU-21 Compiled by ( position+printed name+signature): File administrators Peter Xiao Supervised by ( position+printed name+signature): Test Engineer Jenny Zeng Approved by ( position+printed name+signature) . : Manager Jason Hu Date of issue ................................. : Oct. 31 2022 Representative Laboratory Name ....................................................... : Shenzhen Global Test Service Co.,Ltd. Address ......................................... : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ......................... : Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Address ......................................... : 302, Building 6, no.4 Zhongxing road,Zhangge community, Fucheng street, Longhua district, Shenzhen, Guangdong, P.R.China Test specification ........................ : Standard ........................................ : 47CFR §1.1310 Basis and purpose 47CFR §2.1091 Radiofrequency radiation exposure evaluation: mobile devices TRF Originator .............................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ................................... : Dated 2014-12 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................. : 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module Trade Mark .................................... : N/A Manufacturer ................................. : Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Model/Type reference ................... : FRX-M79AU-21 Listed Models .............................. : N/A Modulation Type ............................ : IEEE 802.11a /802.11b/802.11g/802.11n/802.11ac/802.11ax GFSK, π/4-DQPSK, 8DPSK Operation Frequency .................... : From 2412MHz to 2462MHz, 5180MHz to 5240MHz, 5745MHz to 5825MHz, 2402MHz to 2480MHz Hardware Version ........................ : N/A Software Version ........................... : N/A Rating ............................................ : DC 3.3V Result ............................................ : PASS Report No.: GTS20221010004-1-6 Page 2 of 26 T E S T R E P O R T Test Report No. : GTS20221010004-1-6 Oct. 31 2022 ______________________________________________________________________________________________ Date of issue Equipment under Test : 802.11a/b/g/n/ac/ax 1200Mbps WLAN + Bluetooth v5.2 Combo USB3.0 Module Model /Type : FRX-M79AU-21 Listed model : N/A Applicant : Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Address : 302, Building 6, no.4 Zhongxing road,Zhangge community, Fucheng street, Longhua district, Shenzhen, Guangdong, P.R.China Manufacturer : Shenzhen Feng RuiXiang Intelligent Technology Co., Ltd Address : 302, Building 6, no.4 Zhongxing road,Zhangge community, Fucheng street, Longhua district, Shenzhen, Guangdong, P.R.China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20221010004-1-6 Page 3 of 26 Contents 1. SUMMARY .................................................................................................................................................... 4 1.1 EUT CONFIGURATION .................................................................................................................................... 4 1.2 PRODUCT DESCRIPTION ................................................................................................................................ 4 2. TEST ENVIRONMENT .................................................................................................................................. 6 2.1 ADDRESS OF THE TEST LABORATORY .............................................................................................................. 6 2.2 TEST FACILITY ............................................................................................................................................... 6 2.3 ENVIRONMENTAL CONDITIONS ........................................................................................................................ 6 2.4 STATEMENT OF THE MEASUREMENT UNCERTAINTY .......................................................................................... 6 3. METHOD OF MEASUREMENT ................................................................................................................... 7 3.1 APPLICABLE STANDARD ................................................................................................................................. 7 3.2 REQUIREMENT .............................................................................................................................................. 7 3.3 LIMIT ............................................................................................................................................................. 7 3.4 MPE CALCULATION METHOD ......................................................................................................................... 8 3.5 ANTENNA INFORMATION ..........…

Text truncated - open the document above for the full version.

Case No. : GTS20221010004-1-5 Ambient Condition: 26 °C, 47 %RH, Atmos100.1Kpa, Test Date: 2022.10.19 Test Engineer: Jenny zeng Appendix D.1: Emission Bandwidth Test Result TestMode Antenna Frequency[MHz] 26db EBW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11A Ant1 5180 24.600 5168.280 5192.880 --- --- 5200 23.520 5188.080 5211.600 --- --- 5240 19.840 5230.200 5250.040 --- --- 11N20SISO Ant1 5180 24.640 5167.840 5192.480 --- --- 5200 25.920 5187.520 5213.440 --- --- 5240 20.080 5230.000 5250.080 --- --- 11N40SISO Ant1 5190 39.840 5170.160 5210.000 --- --- 5230 40.080 5210.080 5250.160 --- --- 11AC20SISO Ant1 5180 24.080 5168.280 5192.360 --- --- 5200 24.880 5187.160 5212.040 --- --- 5240 20.080 5229.920 5250.000 --- --- 11AC40SISO Ant1 5190 39.520 5170.320 5209.840 --- --- 5230 40.320 5210.000 5250.320 --- --- 11AC80SISO Ant1 5210 80.320 5169.840 5250.160 --- --- 11AX20SISO Ant1 5180 22.960 5168.240 5191.200 --- --- 5200 21.800 5189.200 5211.000 --- --- 5240 19.840 5230.040 5249.880 --- --- 11AX40SISO Ant1 5190 39.440 5170.240 5209.680 --- --- 5230 39.600 5210.160 5249.760 --- --- 11AX80SISO Ant1 5210 80.000 5170.000 5250.000 --- --- Test Graphs 11A_Ant1_5180 11A_Ant1_5200 11A_Ant1_5240 11N20SISO_Ant1_5180 11N20SISO_Ant1_5200 11N20SISO_Ant1_5240 11N40SISO_Ant1_5190 11N40SISO_Ant1_5230 11AC20SISO_Ant1_5180 11AC20SISO_Ant1_5200 11AC20SISO_Ant1_5240 11AC40SISO_Ant1_5190 11AC40SISO_Ant1_5230 11AC80SISO_Ant1_5210 11AX20SISO_Ant1_5180 11AX20SISO_Ant1_5200 11AX20SISO_Ant1_5240 11AX40SISO_Ant1_5190 11AX40SISO_Ant1_5230 11AX80SISO_Ant1_5210 Appendix D.2: Occupied channel bandwidth Test Result TestMode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11A Ant1 5180 18.018 5171.041 5189.059 --- --- 5200 18.044 5191.049 5209.093 --- --- 5240 16.884 5231.603 5248.487 --- --- 11N20SISO Ant1 5180 18.981 5170.590 5189.571 --- --- 5200 18.950 5190.562 5209.512 --- --- 5240 17.843 5231.098 5248.941 --- --- 11N40SISO Ant1 5190 35.916 5172.120 5208.036 --- --- 5230 36.101 5211.995 5248.096 --- --- 11AC20SISO Ant1 5180 18.884 5170.600 5189.484 --- --- 5200 18.811 5190.619 5209.430 --- --- 5240 17.831 5231.103 5248.934 --- --- 11AC40SISO Ant1 5190 35.936 5172.093 5208.029 --- --- 5230 36.028 5211.993 5248.021 --- --- 11AC80SISO Ant1 5210 74.993 5172.633 5247.626 --- --- 11AX20SISO Ant1 5180 19.204 5170.377 5189.581 --- --- 5200 19.205 5190.390 5209.595 --- --- 5240 18.907 5230.524 5249.431 --- --- 11AX40SISO Ant1 5190 37.523 5171.291 5208.814 --- --- 5230 37.490 5211.256 5248.746 --- --- 11AX80SISO Ant1 5210 76.710 5171.751 5248.461 --- --- Test Graphs 11A_Ant1_5180 11A_Ant1_5200 11A_Ant1_5240 11N20SISO_Ant1_5180 11N20SISO_Ant1_5200 11N20SISO_Ant1_5240 11N40SISO_Ant1_5190 11N40SISO_Ant1_5230 11AC20SISO_Ant1_5180 11AC20SISO_Ant1_5200 11AC20SISO_Ant1_5240 11AC40SISO_Ant1_5190 11AC40SISO_Ant1_5230 11AC80SISO_Ant1_5210 11AX20SISO_Ant1_5180 11AX20SISO_Ant1_5200 11AX20SISO_Ant1_5240 11AX40SISO_Ant1_5190 11AX40SISO_Ant1_5230 11AX80SISO_Ant1_5210 Appendix D.3: Duty Cycle Test Result TestMode Antenna Frequency[MHz] Transmission Duration [ms] Transmission Period [ms] Duty Cycle [%] 11A Ant1 5180 0.71 1.07 66.36 5200 0.71 1.08 65.74 5240 0.70 1.06 66.04 11N20SISO Ant1 5180 0.67 1.04 64.42 5200 0.67 1.04 64.42 5240 0.68 1.04 65.38 11N40SISO Ant1 5190 0.35 0.71 49.30 5230 0.35 0.71 49.30 11AC20SISO Ant1 5180 0.37 0.73 50.68 5200 0.37 0.74 50.00 5240 0.37 0.74 50.00 11AC40SISO Ant1 5190 0.20 0.55 36.36 5230 0.20 0.57 35.09 11AC80SISO Ant1 5210 0.19 0.58 32.76 11AX20SISO Ant1 5180 0.20 0.55 36.36 5200 0.20 0.55 36.36 5240 0.20 0.55 36.36 11AX40SISO Ant1 5190 0.32 0.70 45.71 5230 0.32 0.71 45.07 11AX80SISO Ant1 5210 0.19 0.58 32.76 Test Graphs 11A_Ant1_5180 11A_Ant1_5200 11A_Ant1_5240 11N20SISO_Ant1_5180 11N20SISO_Ant1_5200 11N20SISO_Ant1_5240 11N40SISO_Ant1_5190 11N40SISO_Ant1_5230 11AC20SISO_Ant1_5180 11AC20SISO_Ant1_5200 11AC20SISO_Ant1_5240 11AC40SISO_Ant1_5190 11AC40SISO_Ant1_5230 11AC80SISO_Ant1_5210 11AX20SISO_Ant1_5180 11AX20SISO_Ant1_5200 11AX20SISO_Ant1_5240 11AX40SISO_Ant1_5190 11AX40SISO_Ant1_5230 11AX80SISO_Ant1_5210 Appendix D.4: Maximum conducted output power Test Result Channel Power Test Mode Antenna Frequency[M Hz] Channel Powert [dBm] Duty Cycle [%] DC Factor [dBm] Result [dBm] Limit [dBm] Verdict 11A Ant1 5180 11.22 66.36 1.78 13.00 ≤23.98 PASS 5200 12.38 65.74 1.82 14.20 ≤23.98 PASS 5240 12.75 66.04 1.80 14.55 ≤23.98 PASS 11N20SISO Ant1 5180 10.29 64.42 1.91 12.20 ≤23.98 PASS 5200 12.12 64.42 1.91 14.03 ≤23.98 PASS 5240 10.98 65.38 1.85 12.83 ≤23.98 PASS 11N40SISO Ant1 5190 9.25 49.30 3.07 12.32 ≤23.98 PASS 5230 9.11 49.30 3.07 12.18 ≤23.98 PASS 11AC20SISO Ant1 5180 10.02 50.68 2.95 12.97 ≤23.98 PASS 5200 9.96 50.00 3.01 12.97 ≤23.98 PASS 5240 10.35 50.00 3.01 13.36 ≤23.98 PASS 11AC40SISO Ant1 5190 7.91 36.36 4.39 12.30 ≤23.98 PASS 5230 8.04 35.09 4.55 12.59 ≤23.98 PASS 11AC80SISO Ant1 5210 4.75 32.76 4.85 9.60 ≤23.98 PASS 11AX20SISO Ant1 5180 8.56 36.36 4.39 12.95 ≤23.98 PASS 5200 8.71 36.36 4.39 13.10 ≤23.98 PASS 5240 8.52 36.36 4.39 12.91 ≤23.98 PASS 11AX40SISO Ant1 5190 12.80 45.71 3.40 16.20 ≤23.98 PASS 5230 7.81 45.07 3.46 11.27 ≤23.98 PASS 11AX80SISO Ant1 5210 5.18 32.76 4.85 10.03 ≤23.98 PASS Note：The Duty Cycle Factor is compensated in the graph. Appendix D.5: Maximum power spectral density Test Result TestMode Antenna Frequency[MHz] Result [dBm/MHz] Limit[dBm/MHz] Verdict 11A Ant1 5180 4.49 ≤11.00 PASS 5200 4.92 ≤11.00 PASS 5240 5.44 ≤11.00 PASS 11N20SISO Ant1 5180 3.49 ≤11.00 PASS 5200 3.71 ≤11.00 PASS 5240 4.55 ≤11.00 PASS 11N40SISO Ant1 5190 1.47 ≤11.00 PASS 5230 2.38 ≤11.00 PASS 11AC20SISO Ant1 5180 4.3 ≤11.00 PASS 5200 5.67 ≤11.00 PASS 5240 5 ≤11.00 PASS 11AC40SISO Ant1 5190 3.17 ≤11.00 PASS 5230 3.47 ≤11.00 PASS 11AC80SISO Ant1 5210 3.3 ≤11.00 PASS 11AX20SISO Ant1 5180 5.27 ≤11.00 PASS 5200 5.18 ≤11.00 PASS 5240 5.25 ≤11.00 PASS 11AX40SISO Ant1 5190 2.5 ≤11.00 PASS 5230 3.7 ≤11.00 PASS 11AX80SISO Ant1 5210 1.13 ≤11.00 PASS Note：1.The Result and Limit Unit is dBm/500 kHz in …

Text truncated - open the document above for the full version.

Appendix D.6: Band edge measurements Test Result B1 TestMode Antenna ChName Frequency[MHz] Result[dBm] Limit[dBm] Verdict 11A Ant1 Low 5180 -37.51 ≤-27 PASS High 5240 -37.34 ≤-27 PASS 11N20SISO Ant1 Low 5180 -36.93 ≤-27 PASS High 5240 -37.88 ≤-27 PASS 11N40SISO Ant1 Low 5190 -37.15 ≤-27 PASS High 5230 -36.52 ≤-27 PASS 11AC20SISO Ant1 Low 5180 -36.9 ≤-27 PASS High 5240 -37.97 ≤-27 PASS 11AC40SISO Ant1 Low 5190 -37.29 ≤-27 PASS High 5230 -37.81 ≤-27 PASS 11AC80SISO Ant1 Low 5210 -36.93 ≤-27 PASS High 5210 -37.97 ≤-27 PASS 11AX20SISO Ant1 Low 5180 -37.35 ≤-27 PASS High 5240 -37.16 ≤-27 PASS 11AX40SISO Ant1 Low 5190 -37.48 ≤-27 PASS High 5230 -38.59 ≤-27 PASS 11AX80SISO Ant1 Low 5210 -37.62 ≤-27 PASS High 5210 -38.53 ≤-27 PASS Test Graphs B1 11A_Ant1_Low_5180 11A_Ant1_High_5240 11N20SISO_Ant1_Low_5180 11N20SISO_Ant1_High_5240 11N40SISO_Ant1_Low_5190 11N40SISO_Ant1_High_5230 11AC20SISO_Ant1_Low_5180 11AC20SISO_Ant1_High_5240 11AC40SISO_Ant1_Low_5190 11AC40SISO_Ant1_High_5230 11AC80SISO_Ant1_Low_5210 11AC80SISO_Ant1_High_5210 11AX20SISO_Ant1_Low_5180 11AX20SISO_Ant1_High_5240 11AX40SISO_Ant1_Low_5190 11AX40SISO_Ant1_High_5230 11AX80SISO_Ant1_Low_5210 11AX80SISO_Ant1_High_5210 Appendix D.7: Conducted Spurious Emission Test Result TestMode Antenna Frequency[MHz] FreqRange [MHz] Max. Fre [MHz] Max. Level [dBm] Limit [dBm] Verdict 11A Ant1 5180 30~5140 5136.93 -38.76 ≤-27 PASS 5360~40000 26565.76 -37.55 ≤-27 PASS 5200 30~5140 1748.32 -29.83 ≤-27 PASS 5360~40000 10399.23 -37.23 ≤-27 PASS 5240 30~5140 5122.12 -42.55 ≤-27 PASS 5360~40000 10478.58 -34.7 ≤-27 PASS 11N20SISO Ant1 5180 30~5140 5138.3 -41.08 ≤-27 PASS 5360~40000 24171.65 -37.83 ≤-27 PASS 5200 30~5140 5139.49 -41.7 ≤-27 PASS 5360~40000 24292.84 -37.13 ≤-27 PASS 5240 30~5140 5131.31 -44.48 ≤-27 PASS 5360~40000 10480.02 -37.95 ≤-27 PASS 11N40SISO Ant1 5190 30~5140 5134.72 -42.68 ≤-27 PASS 5360~40000 24843.21 -38.43 ≤-27 PASS 5230 30~5140 5126.54 -45.11 ≤-27 PASS 5360~40000 25154.83 -38.02 ≤-27 PASS 11AC20SISO Ant1 5180 30~5140 5137.96 -41.37 ≤-27 PASS 5360~40000 23502.25 -37.66 ≤-27 PASS 5200 30~5140 5139.49 -42.85 ≤-27 PASS 5360~40000 24233.69 -38.42 ≤-27 PASS 5240 30~5140 5121.94 -44.42 ≤-27 PASS 5360~40000 26783.6 -36.41 ≤-27 PASS 11AC40SISO Ant1 5190 30~5140 5136.08 -42.35 ≤-27 PASS 5360~40000 26961.05 -37.87 ≤-27 PASS 5230 30~5140 2414.33 -31.45 ≤-27 PASS 5360~40000 24292.11 -37.43 ≤-27 PASS 11AC80SISO Ant1 5210 30~5140 5136.93 -42.03 ≤-27 PASS 5360~40000 24216.37 -37.73 ≤-27 PASS 11AX20SISO Ant1 5180 30~5140 1743.21 -38.5 ≤-27 PASS 5360~40000 26846.36 -37.85 ≤-27 PASS 5200 30~5140 1744.06 -33.67 ≤-27 PASS 5360~40000 24856.2 -38.08 ≤-27 PASS 5240 30~5140 1737.59 -44.56 ≤-27 PASS 5360~40000 10477.86 -36.78 ≤-27 PASS 11AX40SISO Ant1 5190 30~5140 5139.15 -36.82 ≤-27 PASS 5360~40000 10387.69 -37.15 ≤-27 PASS 5230 30~5140 5139.15 -45.94 ≤-27 PASS 5360~40000 24284.18 -38.69 ≤-27 PASS 11AX80SISO Ant1 5210 30~5140 1737.93 -44.45 ≤-27 PASS 5360~40000 26060.82 -38.09 ≤-27 PASS Test Graphs 11A_Ant1_5180_30~5140 11A_Ant1_5180_5360~40000 11A_Ant1_5200_30~5140 11A_Ant1_5200_5360~40000 11A_Ant1_5240_30~5140 11A_Ant1_5240_5360~40000 11N20SISO_Ant1_5180_30~5140 11N20SISO_Ant1_5180_5360~40000 11N20SISO_Ant1_5200_30~5140 11N20SISO_Ant1_5200_5360~40000 11N20SISO_Ant1_5240_30~5140 11N20SISO_Ant1_5240_5360~40000 11N40SISO_Ant1_5190_30~5140 11N40SISO_Ant1_5190_5360~40000 11N40SISO_Ant1_5230_30~5140 11N40SISO_Ant1_5230_5360~40000 11AC20SISO_Ant1_5180_30~5140 11AC20SISO_Ant1_5180_5360~40000 11AC20SISO_Ant1_5200_30~5140 11AC20SISO_Ant1_5200_5360~40000 11AC20SISO_Ant1_5240_30~5140 11AC20SISO_Ant1_5240_5360~40000 11AC40SISO_Ant1_5190_30~5140 11AC40SISO_Ant1_5190_5360~40000 11AC40SISO_Ant1_5230_30~5140 11AC40SISO_Ant1_5230_5360~40000 11AC80SISO_Ant1_5210_30~5140 11AC80SISO_Ant1_5210_5360~40000 11AX20SISO_Ant1_5180_30~5140 11AX20SISO_Ant1_5180_5360…

Text truncated - open the document above for the full version.