2AVTT-BL01S2.4G WIFI/BT module

BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved BL-01S User manual Version V1.1 Copyright ©2020 BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved Page 1 of 13 This device is intended only for OEM integrators under the following conditions: 1)The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2)This device and its antenna(s) must not be co‐located with any other transmitters except in accordance with FCC multi‐transmitter product procedures. Referring to the multi‐transmitter policy, multiple‐transmitter(s) and module(s) can be operated simultaneously without C2P. 3)For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end‐user regarding to Regulatory Domain change. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment . If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two co nditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains FCC ID: 2AVTT-BL01S ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body. BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved Page 2 of 13 1. Product Overview BL-01S is a wireless module based on WiFi+BLE single-chip SoC as the main control. It meets low-power, high-performance, low-cost IOT application scenarios. The module's core processor BL602C integrates 2.4G Wi-Fi (802.11 b/g/n) and BLE 5.0 wireless subsystem. Its microcontroller subsystem includes a high-performance and low-power 32-bit RISC-V CPU, high-speed cache and FLASH memory. It has an advanced power management unit and supports a variety of low- power Consumption mode. The module peripheral interface supports UART, GPIO, ADC, PWM, I2C, etc., onboard a switch and an RGB LED light. BL602C functional block diagram: BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved Page 3 of 13 1.1 Appearance and Dimensions BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved Page 4 of 13 BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved Page 5 of 13 1.2 Features 1.2.1 Wireless ◼ IEEE 802.11b/g/n, 1x1 SISO 2.4GHz ◼ Bluetooth® BLE 5.0 ◼ Wi-Fi 20MHz bandwidth ◼ Wi-Fi security WPS/WEP/WPA/WPA2 Personal/ WPA2 Enterprise/WPA3 ◼ STA，SoftAP and Sniffer mode ◼ Wi-Fi and BLE coexist, BLE assists in realizing Wi-Fi fast connection ◼ Integrated balun，PA/LNA ◼ Support Smart Config/AirKiss (WeChat) ◼ Support serial port local upgrade and remote firmware upgrade (FOTA) ◼ General AT commands can be used quickly ◼ Support secondary development, integrated Windows and Linux development environment 1.2.2 MCU Subsystem ◼ 32-bit RISC-V CPU with FPU (floating point unit) ◼ One RTC timer (cycle one year) ◼ Two 32-bit general-purpose timers ◼ Four DMA channels BL-01S WIFI+BLE module Copyright © 2020 ShenzhenJiXinInteligence Co., Ltd All Rights Reserved Page 6 of 13 ◼ DFS (Dynamic Frequency Scaling) from 1MHz to 192MHz ◼ JTAG development support ◼ XIP QSPI Flash has hardware encryption support 1.2.3 Memory ◼ 276KB RAM ◼ 128KB ROM ◼ 1Kb eFuse ◼ Embedded 2M Byte flash 1.2.4 Security Mechanism ◼ QSPI Flash Instant AES Decryption (OTFAD)-AES-128, CTR mode …

Text truncated - open the document above for the full version.

C5266091_X8_Ed.1 1/1 LetterofAuthorization Company:ShenzhenJixinintelligenceCo.,Ltd Address:A505Room,BusinessBuilding,SuojiaSciencePark,Xixiang,Baoan District,Shenzhen ProductName:2.4GWIFI/BTmodule ModelNumber:BL-01S FCCIdentifier: 2AVTT-BL01S WeauthorizeLGAITechnologicalCenterS.A.,RondadelaFontdelCarme,s/n, 08193Bellaterra,Spain,toactonourbehalfonallmattersconcerningthe abovenamedequipment. AnyindividualwithinLGAITechnologicalCenterS.A.isauthorizedtoactonour behalfandtakeactionontheapplication. WedeclarethatauthorizeLGAITechnologicalCenterS.A.,RondadelaFontdel Carme,s/n,08193Bellaterra,Spain,isallowedtoforwardallinformation relatedtotheapprovalprojecttotheFederalCommunicationCommissionand todiscussanyissuesconcerningtheapprovalapplication.Anyandallacts carriedoutbyLGAITechnologicalCenterS.A.onourbehalfshallhavethe sameeffectasactsofourown. Name:HuabinFu Date:2/23/2021 Title:CEO Signatureofapplicant:

C5266091_X10_Ed.1 1/1 ShenzhenJixinintelligenceCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 Date:2/23/2021 Subject:RequestforConfidentiality FCCID:2AVTT-BL01S ToWhomItMayConcern, PursuanttotheprovisionsofSections0.457and0.459ofCommission'srules (47CFR0.457,0.459),wearerequestingtheCommissiontowithholdthefollowing attachment(s)asconfidentialdocumentfrompublicdisclosure. ExhibitsLong-Term Confidentiality Short-Term Confidentiality IDLabel/LocationNoNo AttestationStatementNoNo ExternalPhotosNo BlockDiagram Schematics TestReportNoNo TestSetupPhotosNo User’sManual InternalPhotos PartsList/TuneUp RFExposureInfo OperationalDescription CoverLetter(s)NoNo SDRSoftware/SecurityInfoNo Abovementioneddocumentcontainsdetailedsystemandequipmentdescriptionare consideredasproprietaryinformationinoperationoftheequipment.Thepublic disclosureofabovedocumentsmightbeharmfultoourcompanyandwouldgive competitoranunfairadvantageinthemarket. Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatand correspondentduringcertificationreviewprocesscannotbegrantedasconfidential documentsandthoseinformationwillbeavailableforpublicreviewoncethegrantof equipmentauthorizationisissued. Sincerely, Signature: Name:HuabinFu Date: 2/23/2021 Title:CEO

C5266091_X9_Ed.1 1/1 ModularTransmitterApprovalRequest FederalCommunicationsCommission EquipmentAuthorizationBranch 7435OaklandMillsRoad Columbia,MD21046 Companyname:ShenzhenJixinintelligenceCo.,Ltd FCCID:2AVTT-BL01S Gentlemen, Inaccordancewith47CFR15.212ModularTransmittersandKDB996369D01‘Module CertificationGuidev01r04’.FCCID:2AVTT-BL01Shasbeenexaminedagainstthe followingrequirements. Requirementper15.212andKDB996369D01 ‘ModularCertificationGuidev01r04 ExplanationfromGrantee (donotwriteyes/no,butexplainwhyproduct complies/howitisachieved) Theradioelementsmusthavetheradiofrequencycircuitry shielded.Physicalcomponentsandtuningcapacitor(s)may belocatedexternaltotheshield,butmustbeonthemodule assembly Yes,ThemodulehasitsownRFshield Themodulemusthavebufferedmodulation/datainputsto ensurethatthedevicewillcomplywithPart15requirements withanytypeofinputsignal Yes,Themodulehasdatatransmission functionandsupports2.4GWIFI&BLE function. Themodulemustcontainpowersupplyregulationonthe module Modulewithpowerregulationand supportforDC3.3Vinput Themodulemustcontainapermanentlyattachedantenna, orcontainauniqueantennaconnector,andbemarketed andoperatedonlywithspecificantenna(s),perSections 15.203,15.204(b),15.204(c),15.212(a),2.929(b) Themodulemeetstheantenna requirements. Themodulemustdemonstratecomplianceinastand-alone configuration Themodulehasbeentestedinastand aloneconfiguration,seereport fordetails Themodulemustbelabelledwithitspermanentlyaffixed FCCIDlabel,oruseanelectronicdisplay(SeeKDB Publication784748aboutlabellingrequirements) ThemodulehasitsownFCCID number.Seethelabelfordetails. Themodulemustcomplywithallspecificrulesapplicableto thetransmitterincludingalltheconditionsprovidedinthe integrationinstructionsbythegrantee Themodulemeetsanyspecificrulesor operationalrequirementsapplicable tothetransmitter ThemodulemustcomplywithRFexposurerequirements Themodulecomplieswithany applicableRFexposurerequirements, asdetailedintheinstructions. Name:HuabinFuDate:2021-02-23 Title:CEO Signatureofapplicant

1 - Page 1 of 2 - Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. APPENDIX 1: EUT PHOTO Photo 1 (For model BL-01S) Photo 2 1 - Page 2 of 2 - Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Photo 3 ----END OF REPORT---- PCB antenna

Location SIZE: 10mm*2mm Label FCC ID:2AVTT-BL01S

1 - Page 2 of 2 - Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: [email protected] Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Photo 3 ----END OF REPORT---- PCB antenna

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] MPE Test Report Report No.: MTi201228031-10E3 Date of issue: Feb. 03, 2021 Applicant: Shenzhen Jixin intelligence Co., Ltd Product name: 2.4G WIFI/BT module Model(s): BL-01S FCC ID: 2AVTT-BL01S Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 6 - Report No.: MTi201228031-10E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 6 - Report No.: MTi201228031-10E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1 RF EXPOSURE EVALUATION ............................................................................................................................ 5 1.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................................................................ 5 1.2 MEASUREMENT RESULT ......................................................................................................................................... 6 - Page 4 of 6 - Report No.: MTi201228031-10E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Testing Engineer : (Danny Xu) Technical Manager : (Leo Su) Authorized Signatory : (Tom Xue) TEST RESULT CERTIFICATION Applicant’s name ................... Shenzhen Jixin intelligence Co., Ltd Address ................................. A505 Room, Business Building, Suojia Science Park, Xixiang, Baoan District, Shenzhen Manufacturer's Name ............ Shenzhen Jixin intelligence Co., Ltd Address ................................. A505 Room, Business Building, Suojia Science Park, Xixiang, Baoan District, Shenzhen Product description Product name ............................ 2.4G WIFI/BT module Trademark ............................ N/A Model Name ......................... BL-01S Serial Model ........................... N/A Standards .............................. N/A Test procedure ...................... KDB 447498 D01 v06 Date of Test Date (s) of performance of tests ............. : Jan. 04, 2021 ~ Feb. 03. 2021 Test Result ............................................. : Pass This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. - Page 5 of 6 - Report No.: MTi201228031-10E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] 1 RF EXPOSURE EVALUATION According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) Radiation as specified in §1.1307(b) 1.1 Limits for Maximum Permissible Exposure (MPE) MPE Calculation Method Friis transmission formula: Pd= (Pout*G)\ (4*pi*R 2 ) Where Pd= Power density in mW/cm2 Pout=output power to antenna in mW G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1415926 R= distance between observation point and center of the radiator in cm(20cm) Pd the limit of MPE, 1mW/cm2. If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. - Page 6 of 6 - Report No.: MTi201228031-10E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] 1.2 Measurement Result WIFI: Operation Frequency: WIFI 802.11b/g/n HT20: 2412-2462MHz, BLE: GFSK 2402-2480MHz, Power density limited: 1mW/ cm 2 Antenna Type: PCB Antenna; WIFI antenna gain: 2dBi R=20cm mW=10^(dBm/10) antenna gain Numeric=10^(dBi/10)= 10^(2/10)=1.58 WIFI: Channel Freq. (MHz) modulation conducted power Tune- up power Max Antenna Evaluation result at 20cm Power density Limits (dBm) (dBm) tune-up power Gain Power density(mW/cm2 ) (mW/cm2) (dBm) (mW) Numeric Ant A Ant A Ant A Ant A Ant A Ant A 2412 802.11b 13.18 14±1 15 31.622777 1.58 0.0100 1 2437 13.92 14±1 15 31.622777 1.58 0.0100 1 2462 13.81 14±1 15 31.622777 1.58 0.0100 1 2412 802.11g 13.12 14±1 15 31.622777 1.58 0.0100 1 2437 13.80 14±1 15 31.622777 1.58 0.0100 1 2462 14.45 14±1 15 31.622777 1.58 0.0100 1 2412 802.11n H20 13.13 14±1 15 31.622777 1.58 0.0100 1 2437 13.98 14±1 15 31.622777 1.58 0.0100 1 2462 14.21 14±1 15 31.622777 1.58 0.0100 1 Bluetooth DTS: Channel Freq. (MHz) modulation conducted power Tune- up power (dBm) Max Antenna Evaluation result Power density Limits (dBm) tune-up power Gain (mW/cm2 ) (mW/cm2) (dBm) (mW) (dBi) Numeric 2402 GFSK 5.871 6±1 7 5.012 2 …

Text truncated - open the document above for the full version.

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi201228031-10E2 Date of issue: Feb. 03, 2021 Applicant: Shenzhen Jixin intelligence Co., Ltd Product name: 2.4G WIFI/BT module Model(s): BL-01S FCC ID: 2AVTT-BL01S Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 41 - Report No.: MTi201228031-10E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 41 - Report No.: MTi201228031-10E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1. GENERAL INFORMATION ................................................................................................................................... 6 1.1. DESCRIPTION OF EUT ................................................................................................................................................... 6 1.2. OPERATION CHANNEL LIST .............................................................................................................................................. 6 1.3. TEST CHANNEL LIST ....................................................................................................................................................... 6 1.4. ANCILLARY EQUIPMENT LIST ........................................................................................................................................... 7 1.5. DESCRIPTION OF SUPPORT UNITS .................................................................................................................................... 7 2. SUMMARY OF TEST RESULT S .......................................................................................................................... 8 3. TEST FACILITIES AND ACCREDITATIONS ...................................................................................................... 9 3.1. TEST LABORATORY ........................................................................................................................................................ 9 3.2. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 9 3.3. MEASUREMENT UNCERTAINTY ........................................................................................................................................ 9 3.4. TEST SOFTWARE ........................................................................................................................................................... 9 4. EQUIPMENT LIST ............................................................................................................................................... 10 5. TEST RESULT ..................................................................................................................................................... 11 5.1. ANTENNA REQUIREMENT ............................................................................................................................................. 11 5.1.1 Standard Requirement ...................................................................................................................................... 11 5.1.2 EUT Antenna ..................................................................................................................................................... 11 5.2. PEAK OUTPUT POWER TEST ......................................................................................................................................... 12 5.2.1 Limit .................................................................................................................................................................. 12 5.2.2 Test setup .......................................................................................................................................................... 12 5.2.3 Test Procedure ................................................................................................................................................... 12 5.2.4 Te s t Results ........................................................................................................................................................ 12 5.3. CONDUCTED EMISSION ................................................................................................................................................ 15 5.3.1 Limits ................................................................................................................................................................. 15 5.3.2 Te s t Setup .......................................................................................................................................................... 15 5.3.3 Te st Procedure ................................................................................................................................................... 16 5.3.4 Te s t Results ............…

Text truncated - open the document above for the full version.

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi201228031-10E1 Date of issue: Feb. 03, 2021 Applicant: Shenzhen Jixin intelligence Co., Ltd Product name: 2.4G WIFI/BT module Model(s): BL-01S FCC ID: 2AVTT-BL01S Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 48 - Report No.: MTi201228031-10E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 48 - Report No.: MTi201228031-10E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1 GENERAL INFORMATION .......................................................................................................................................... 6 1.1 DESCRIPTION OF EUT ................................................................................................................................................... 6 1.2 OPERATION CHANNEL LIST .............................................................................................................................................. 7 1.3 TEST CHANNEL LIST ....................................................................................................................................................... 7 1.4 ANCILLARY EQUIPMENT LIST ........................................................................................................................................... 7 1.5 DESCRIPTION OF SUPPORT UNITS .................................................................................................................................... 8 2 SUMMARY OF TEST RES U LT S .................................................................................................................................... 9 3 TEST FACILITIES AND ACCREDITATIONS ................................................................................................................... 10 3.1 TEST LABORATORY ...................................................................................................................................................... 10 3.2 ENVIRONMENTAL CONDITIONS ...................................................................................................................................... 10 3.3 MEASUREMENT UNCERTAINTY ...................................................................................................................................... 10 3.4 TEST SOFTWARE ......................................................................................................................................................... 10 4 EQUIPMENT LIST .................................................................................................................................................... 11 5 TEST RESULT ........................................................................................................................................................... 12 5.1 ANTENNA REQUIREMENT ............................................................................................................................................. 12 5.1.1 Standard requirement ....................................................................................................................................... 12 5.1.2 EUT antenna ..................................................................................................................................................... 12 5.2 PEAK OUTPUT POWER ................................................................................................................................................. 13 5.2.1 Limit .................................................................................................................................................................. 13 5.2.2 Test setup .......................................................................................................................................................... 13 5.2.3 Test procedure ................................................................................................................................................... 13 5.2.4 Te s t results......................................................................................................................................................... 14 5.3 POWER SPECTRAL DENSITY ........................................................................................................................................... 15 5.3.1 Limit .................................................................................................................................................................. 15 5.3.2 Test setup .......................................................................................................................................................... 15 5.3.3 Test procedure ................................................................................................................................................... 15 5.3.4 Test…

Text truncated - open the document above for the full version.

Model: BL-01S Radiated emission Conducted emission