2AVY8-8809RC TOYS

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement in portable exposure condition without restriction.

Guangdong Amwell Toys Industry Co., Ltd Covered Equipment Certification Attestation Letter 6/8/2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AVY8-8809 Guangdong Amwell Toys Industry Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not “covered” equipment. Guangdong Amwell Toys Industry Co., Ltd (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Guangdong Amwell Toys Industry Co., Ltd (“the applicant”) certifies that the equipment for which authorization is sought does not include cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software pursuant to DA-24-886 and KDB 986446 D01 Covered Equipment Guidance section B(2a). Signed: Printed name: DUQUN YANG Title: GENERAL MANAGER Company Name: Guangdong Amwell Toys Industry Co., Ltd Date: 6/8/2026

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¶VREOLJDWLRQWRDFFHSWVHUYLFHRISURFHVVLQ WKH8QLWHG6WDWHVIRUPDWWHUVUHODWHGWRWKHDSSOLFDEOHHTXLSPHQWDQGDWWKHSK\VLFDO86DGGUHVVDQGH PDLORIWKHGHVLJQDWHGDJHQWOLVWHGDERYH :H*XDQJGRQJ$PZHOO7R\V,QGXVWU\&R/WG!DQG3LFXV$GYLVRUV86//&!DFNQRZOHGJHWKH DSSOLFDQW¶VDFFHSWDQFHRILWVREOLJDWLRQWRPDLQWDLQDQDJHQWIRUVHUYLFHRISURFHVVLQWKH8QLWHG6WDWHVIRU QROHVVWKDQRQH\HDUDIWHUHLWKHUWKHJUDQWHHKDVSHUPDQHQWO\WHUPLQDWHGDOOPDUNHWLQJDQGLPSRUWDWLRQ RIWKHDSSOLFDEOHHTXLSPHQWZLWKLQWKH86RUWKHFRQFOXVLRQRIDQ\&RPPLVVLRQUHODWHGDGPLQLVWUDWLYH RUMXGLFLDOSURFHHGLQJLQYROYLQJWKHHTXLSPHQWZKLFKHYHULVODWHU $SSOLFDQW *XDQJGRQJ$PZHOO7R\V,QGXVWU\&R/WG 86GHVLJQDWHGDJHQW 3LFXV$GYLVRUV86//& 1DPH 3ULQWHG '8481<$1*1DPH 3ULQWHG ,YDQ:DQJ 7LWOH*(1(5$/0$1$*(57LWOH&(2 6LJQDWXUH6LJQDWXUH

Guangdong Amwell Toys Industry Co., Ltd DATE: 6/8/2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen Tongzhou Testing Co.,Ltd. (1st Floor, Building 1, Haomai High-tech Park, Huating Road 387, Dalang Street, Longhua, Shenzhen, China) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission’s regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Guangdong Amwell Toys Industry Co., Ltd (Xingda Industrial Park, Fengxiang, Chenghai, Shantou City, Guangdong Province, China) <Signature> Name: DUQUN YANG Title: GENERAL MANAGER Applicant Company: Guangdong Amwell Toys Industry Co., Ltd

Date: 6/8/2026 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Compliance Testing, LLC to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). Sincerely, <Signature> Name: DUQUN YANG Title: GENERAL MANAGER Company: Guangdong Amwell Toys Industry Co., Ltd

Date: 6/8/2026 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AVY8-8809 Product Name: RC TOYS Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we hereby request that the following documents be held confidential: (List here the documents for which you are seeking confidentiality – for example ...) • Schematics • Block diagram • Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. <Signature> Name: DUQUN YANG Title: GENERAL MANAGER Company: Guangdong Amwell Toys Industry Co., Ltd

Report No.:TZ0035260479PH02 Page 1 of 5 External Photographs of EUT External Photo 1 External Photo 2 Report No.:TZ0035260479PH02 Page 2 of 5 External Photo 3 External Photo 4 Report No.:TZ0035260479PH02 Page 3 of 5 External Photo 5 External Photo 6 Report No.:TZ0035260479PH02 Page 4 of 5 External Photo 7 External Photo 8 Report No.:TZ0035260479PH02 Page 5 of 5 External Photo 9

The size of the label is 15mm*10mm with White forecolor. The size of the logo is 5mm*5mm. FCC ID: 2AVY8-8809

Report No.:TZ0035260479PH03 Page 1 of 3 Internal Photographs of EUT Internal Photo 1 Internal Photo 2 Report No.:TZ0035260479PH03 Page 2 of 3 Internal Photo 3 Internal Photo 4 Report No.:TZ0035260479PH03 Page 3 of 3 Internal Photo 5 SRD antenna

FCC ID: 2AVY8-8809 Page 1 of 2 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd RADIO FREQUENCY EXPOSURE Limit According to section B.4 of 447498 D04 Interim General RF Exposure Guidance v01 SAR-based thresholds are derived based on frequency, power, and separation distance of the RF source. The formula defines the thresholds in general for either available maximum time-averaged power or maximum time-averaged ERP, whichever is greater. If the ERP of a device is not easily determined, such as for a portable device with a small form factor, the applicant may use the available maximum time-averaged power exclusively if the device antenna or radiating structure does not exceed an electrical length of λ/4. As for devices with antennas of length greater than λ/4 where the gain is not well defined, but always less than that of a half-wave dipole (length λ/2), the available maximum time-averaged power generated by the device may be used in place of the maximum time-averaged ERP, where that value is not known. The separation distance is the smallest distance from any part of the antenna or radiating structure for all persons, during operation at the applicable ERP. In the case of mobile or portable devices, the separation distance is from the outer housing of the device where it is closest to the antenna. The SAR-based exemption formula of § 1.1307(b)(3)(i)(B), repeated here as Formula (B.2), applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power or effective radiated power (ERP), whichever is greater, of less than or equal to the threshold Pth (mW). This method shall only be used at separation distances from 0.5 cm to 40 cm and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by Formula (B.2). Where and f is in GHz, d is the separation distance (cm), and ERP 20cm is per Formula (B.1). FCC ID: 2AVY8-8809 Page 2 of 2 This report shall not be reproduced except in full, without the written approval of Shenzhen Tongzhou Testing Co.,Ltd Results RF Exposure at Separation distance (cm): 0.5 Mode Antenna Frequency [MHz] Conducted Power [dBm] Manufacturing tolerance Antenna Gain [dBi] Max of ERP and Conducted Power including Tune Up SAR- based exemption threshold Pth [mW] Target Power [dBm] Tolerance ±[dB] [dBm] [mW] SRD Ant1 2403 -1.76 -2.5 1 2.2 -1.45 0.72 2.79 SRD Ant1 2440 -1.08 -1.5 1 2.2 -0.45 0.90 2.75 SRD Ant1 2477 -1.4 -2 1 2.2 -0.95 0.80 2.72 Max of ERP and Conducted Power including Tune Up (dBm) = Max Conducted Tune Up Power(dBm) and Max Conducted Tune Up Power(dBm) + Antenna Gain(dBi)-2.15), whichever is greater. The Maximum Erp is used for Routine Evaluation Exemption according to B.4 of 447498 D04 Interim General RF Exposure Guidance v01. So, the SAR evaluation is not required.

Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 1 of 23 Appendix Test Data for SRD (Conducted Measurement) Product Name: RC TOYS Trade Mark: / Test Model: 8809 FCC ID: 2AVY8-8809 Environmental Conditions Temperature: 23.5°C Relative Humidity: 58% ATM Pressure: 100.0 kPa Test Engineer: Allen Lai Supervised by: Max Zhang NOTE N/A Appendix A: DTS Bandwidth Test Result Test Mode Antenna Frequency [MHz] DTS BW [MHz] FL [MHz] FH [MHz] Limit [MHz] Verdict SRD Ant1 2403 0.604 2402.672 2403.276 0.5 PASS SRD Ant1 2440 0.600 2439.676 2440.276 0.5 PASS SRD Ant1 2477 0.612 2476.684 2477.296 0.5 PASS Note: offset(dB) = cable loss(dB) + attenuator factor(dB) Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 2 of 23 Test Graphs SRD-Ant1-2403-PASS SRD-Ant1-2440-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 3 of 23 SRD-Ant1-2477-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 4 of 23 Appendix B: Occupied Channel Bandwidth Test Result Test Mode Antenna Frequency [MHz] OCB [MHz] FL [MHz] FH [MHz] Limit [MHz] Verdict SRD Ant1 2403 0.71266 2402.6352 2403.3479 --- --- SRD Ant1 2440 0.75758 2439.6160 2440.3735 --- --- SRD Ant1 2477 0.74039 2476.5991 2477.3395 --- --- Note: offset(dB) = cable loss(dB) + attenuator factor(dB) Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 5 of 23 Test Graphs SRD-Ant1-2403 SRD-Ant1-2440 Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 6 of 23 SRD-Ant1-2477 Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 7 of 23 Appendix C: Maximum peak conducted output power Test Result Peak Test Mode Antenna Frequency [MHz] Conducted Peak Power [dBm] Conducted Limit [dBm] Verdict SRD Ant1 2403 -1.76 ≤30 PASS SRD Ant1 2440 -1.08 ≤30 PASS SRD Ant1 2477 -1.40 ≤30 PASS Note: offset(dB) = cable loss(dB) + attenuator factor(dB) Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 8 of 23 Test Graphs Peak SRD-Ant1-2403-PASS SRD-Ant1-2440-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 9 of 23 SRD-Ant1-2477-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 10 of 23 Appendix D: Maximum peak power spectral density Test Result Test Mode Antenna Frequency [MHz] Result [dBm/3kHz] Limit [dBm/3kHz] Verdict SRD Ant1 2403 -8.39 ≤8.00 PASS SRD Ant1 2440 -7.86 ≤8.00 PASS SRD Ant1 2477 -8.14 ≤8.00 PASS Note: offset(dB) = cable loss(dB) + attenuator factor(dB) Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 11 of 23 Test Graphs SRD-Ant1-2403-PASS SRD-Ant1-2440-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 12 of 23 SRD-Ant1-2477-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 13 of 23 Appendix E: Band edge measurements Test Result Test Mode Antenna Ch. Name Frequency [MHz] Ref. Level [dBm] Result [dBm] Limit [dBm] Verdict SRD Ant1 Low 2403 -2.57 -42.74 ≤-22.57 PASS SRD Ant1 High 2477 -2.40 -45.78 ≤-22.4 PASS Note: offset(dB) = cable loss(dB) + attenuator factor(dB) Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 14 of 23 Test Graphs SRD-Ant1-2403-PASS SRD-Ant1-2477-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 15 of 23 Appendix F: Conducted Spurious Emission Test Result Test Mode Antenna Frequency [MHz] Freq. Range [MHz] Ref. Level [dBm] Result [dBm] Limit [dBm] Verdict SRD Ant1 2403 0~Reference -2.70 -2.70 --- PASS SRD Ant1 2403 30~1000 -2.70 -61.8 ≤-22.7 PASS SRD Ant1 2403 1000~26500 -2.70 -48.01 ≤-22.7 PASS SRD Ant1 2440 0~Reference -2.23 -2.23 --- PASS SRD Ant1 2440 30~1000 -2.23 -72.53 ≤-22.23 PASS SRD Ant1 2440 1000~26500 -2.23 -47.39 ≤-22.23 PASS SRD Ant1 2477 0~Reference -2.26 -2.26 --- PASS SRD Ant1 2477 30~1000 -2.26 -72.99 ≤-22.26 PASS SRD Ant1 2477 1000~26500 -2.26 -45.38 ≤-22.26 PASS Note: offset(dB) in Reference test plots = cable loss(dB) + attenuator factor(dB); For spurious emissions plots from 30MHz to 26.5GHz, the cable loss and attenuator factors have been set in the 'Input Correction' of the Spectrum Analyzer during the test. Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 16 of 23 Test Graphs SRD-Ant1-2403-0~Reference-PASS SRD-Ant1-2403-30~1000-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 17 of 23 SRD-Ant1-2403-1000~26500-PASS SRD-Ant1-2440-0~Reference-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 18 of 23 SRD-Ant1-2440-30~1000-PASS SRD-Ant1-2440-1000~26500-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 19 of 23 SRD-Ant1-2477-0~Reference-PASS SRD-Ant1-2477-30~1000-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 20 of 23 SRD-Ant1-2477-1000~26500-PASS Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 21 of 23 Appendix G: Duty Cycle Test Result Test Mode Antenna Frequency [MHz] ON Time [ms] Period [ms] Duty Cycle [%] Duty Cycle Factor [dB] SRD Ant1 2403 1.04 19.88 5.23 12.81 SRD Ant1 2440 1.04 19.88 5.23 12.81 SRD Ant1 2477 1.04 19.84 5.24 12.81 Note: offset(dB) = cable loss(dB) + attenuator factor(dB) Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 22 of 23 Test Graphs NTNV-SRD-Ant1-2403 NTNV-SRD-Ant1-2440 Appendix Test Data of the Report No.:TZ0035260479FRF02 Page 23 of 23 NTNV-SRD-Ant1-2477

Report No.:TZ0035260479FRF13 Page 1 of 31 This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Tongzhou Testing Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Tongzhou Testing Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report apply only to the specific sample(s) tested under stated test conditions. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. TEST REPORT Report Number : TZ0035260479FRF13 Product Name : RC TOYS Model/Type reference : 8809 FCC ID : 2AVY8-8809 Prepared for : Guangdong Amwell Toys Industry Co., Ltd Xingda Industrial Park, Fengxiang, Chenghai, Shantou City, Guangdong Province, China Prepared By : Shenzhen Tongzhou Testing Co.,Ltd. 1st Floor, Building 1, Haomai High-tech Park, Huating Road 387, Dalang Street, Longhua, Shenzhen, China Standards : FCC CFR Title 47 Part 15C, ANSI C63.10-2020+Cor. 1-2023 Date of Test : 2026-04-28 ~ 2026-05-13 Date of Issue : 2026-05-14 Prepared by : Lena Wen Reviewed by : Allen Lai Approved by : Max Zhang (Authorized Officer) Report No.:TZ0035260479FRF13 Page 2 of 31 ** Report Revise Record ** Report Version Revise Time Issued Date Valid Version Notes V1.0 / 2026-05-14 Valid Initial release Report No.:TZ0035260479FRF13 Page 3 of 31 TABLE OF CONTENTS 1. G E N E R A L I N F O R M A T I O N ....................................................... 4 1.1. Client Information ................................................................................................................... 4 1.2. Description of Device (EUT) ................................................................................................... 4 1.3. Wireless Function Tested in this Report .............................................................................. 4 1.4. EUT configuration ................................................................................................................... 5 1.5. Description of Test Facility .................................................................................................... 5 1.6. Statement of the Measurement Uncertainty ......................................................................... 6 1.7. Measurement Uncertainty ...................................................................................................... 6 1.8. Description of Test Modes ..................................................................................................... 6 1.9. Frequency of Channels .......................................................................................................... 7 2. T E S T M E T H O D O L O G Y ............................................................ 8 2.1. EUT Configuration .................................................................................................................. 8 2.2. EUT Exercise ........................................................................................................................... 8 2.3. Test Sample ............................................................................................................................. 8 3. S Y S T E M T E S T C O N F I G U R A T I O N .............................................. 9 3.1. Justification ............................................................................................................................. 9 3.2. EUT Exercise Software ........................................................................................................... 9 3.3. Special Accessories ............................................................................................................... 9 3.4. Block Diagram/Schematics .................................................................................................... 9 3.5. Equipment Modifications ....................................................................................................... 9 3.6. Test Setup ................................................................................................................................ 9 4. S U M M A R Y O F T E S T R E S U L T S ............................................... 10 5. T E S T R E S U L T .................................................................... 11 5.1. On Time and Duty Cycle ....................................................................................................... 11 5.2. Maximum Peak Conducted Output Power Measurement ................................................. 12 5.3. Power Spectral Density Measurement ................................................................................ 13 5.4. 6 dB Spectrum Bandwidth and Occupied Channel Bandwidth Measurement ............... 14 5.5. Radiated Emissions Measurement ...................................................................................... 15 5.6. Conducted Spurious Emissions and Band Edges Test .................................................... 24 5.8. Band-edge measurements for radiated emissions ........................................................... 26 5.9. Antenna Requirements ......................................................................................................... 29 6. L I S T O F M E A S U R I N G E Q U I P M E N T ......................................... 30 7. T E S T S E T U P P H O T O G R A P H S O F E U T ..................................... 31 8. E X T E R I O R P H O T O G R A P H S O F E U T ........................................ 31 9. I N T E R I O R P H O T O G R A P H S O F E U T ........................................ 31 Report No.:TZ0035260479FRF13 Page 4 of 31 1. G E N E R A L I N F O R M A T I O N 1.1. Client Information Applicant : Guangdong Amwell Toys Industry Co., Ltd Address : Xingda Industrial Park, Fengxiang, Chenghai…

Text truncated - open the document above for the full version.

Page 1 of 15 Antenna Test Report Report No.: AGC09272221202PA01 PRODUCT DESIGNATION : RC TOYS,RC ROBOTS BRAND NAME : N/A MODEL NAME : 1088, 09-039, 09-139, 09-839, 09-939, 2048, 2049, 2056A, 2059, 2069, 2079, 2089, 2099, 3086A, 2088, 3088, 4088, 5088, 6088, 7088, 8088, 9088, 8080A, 9090A, 3066A, 3066B, 3066C, 18081, 18082, 18083, 18011, 18012, 8801, 8802, 8803, 8804, 8805, 303554, 303555, 303558, 303559, NX01, 2101, 6601 APPLICANT : Guangdong Amwell Toys Industry Co., Ltd DATE OF ISSUE : Dec. 12, 2022 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC09272221202PA01 Page 2 of 15 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Dec. 12, 2022 Valid Initial release Report No.: AGC09272221202PA01 Page 3 of 15 TABLE OF CONTENTS 1. PRODUCT INFORMATON ...................................................................................................................... 4 2. TEST FACILITY ....................................................................................................................................... 5 3. TEST EQUIPMENT LIST ......................................................................................................................... 5 4. MEASUREMENT UNCERTAINTY .......................................................................................................... 5 5. TEST SUMMARY LIST ............................................................................................................................ 5 6. TEST SETUP ........................................................................................................................................... 6 7. TEST RESULTS ....................................................................................................................................... 7 7.1. VSWR ................................................................................................................................................ 7 7.2. GAIN AND EFFICIENCY ................................................................................................................... 8 7.3. RADIATION PATTERN ...................................................................................................................... 9 APPENDIX A: PHOTOGRAPHS OF TEST SETUP ................................................................................. 11 APPENDIX B: PHOTOGRAPHS OF EUT ................................................................................................ 12 Report No.: AGC09272221202PA01 Page 4 of 15 1. PRODUCT INFORMATON General information Applicant Guangdong Amwell Toys Industry Co., Ltd Address Xingda Industrial Park, Fengxiang, Chenghai, Shantou City, Guangdong Province, China Manufacturer Guangdong Amwell Toys Industry Co., Ltd Address Xingda Industrial Park, Fengxiang, Chenghai, Shantou City, Guangdong Province, China Factory Guangdong Amwell Toys Industry Co., Ltd Address Xingda Industrial Park, Fengxiang, Chenghai, Shantou City, Guangdong Province, China Product Designation RC TOYS,RC ROBOTS Brand Name N/A Test Model 1088 Series Model 09-039, 09-139, 09-839, 09-939, 2048, 2049, 2056A, 2059, 2069, 2079, 2089, 2099, 3086A, 2088, 3088, 4088, 5088, 6088, 7088, 8088, 9088, 8080A, 9090A, 3066A, 3066B, 3066C, 18081, 18082, 18083, 18011, 18012, 8801, 8802, 8803, 8804, 8805, 303554, 303555, 303558, 303559, NX01, 2101, 6601 Difference Description All the series models are the same as the test model except for the model names and the color of appearance. Date of receipt of test item Dec.07, 2022 Date of test Dec.09, 2022 Report Template AGCRT-ER-PA/V1.0 Technical information Frequency Range 2400-2500MHz Test Frequencies 2400MHz, 2410MHz, 2420MHz, 2430MHz, 2440MHz, 2450MHz, 2460MHz, 2470MHz, 2480MHz, 2490MHz, 2500MHz Antenna Type Wire antenna Dimensions 32mm Impedance 50Ω Maximum test values Gain: 2.200dBi; Efficiency: 26.944%; VSWR: 1.178:1 The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. The test results of this report relate only to the tested sample identified in this report. Prepared By Alan Duan (Project Engineer) Dec.12, 2022 Reviewed By Calvin Liu (Reviewer) Oct. 12, 2022 Approved By Max Zhang (Authorized Officer) Oct. 12, 2022 Report No.: AGC09272221202PA01 Page 5 of 15 2. TEST FACILITY 3. TEST EQUIPMENT LIST Equipment Manufacturer Model Cal. Date Cal. Due ANTENNA MEASUREMENT SYSTEM ETS-Lindgren AMS-8600 Nov. 26, 2022 Nov. 25, 2023 Network Analyzer R&S 101443 Oct. 15, 2022 Oct. 14, 2023 Test software ETS-Lindgren EMQuest (Ver V1.12) N/A N/A 4. MEASUREMENT UNCERTAINTY The uncertainty is calculated using the methods suggested in the “Guide to the Expression of Uncertainty in measurement” (GUM) published by CISPR and ANSI. - Uncertainty of VSWR, Uc = ±1.5dB - Uncertainty of Gain, Uc = ±0.8dB 5. TEST SUMMARY LIST NO. Test item Remark 1 VSWR -- 2 Gain and efficiency -- 3 Radiation pattern -- Test Site Attestation of Global Compliance (Shenzhen) Co., Ltd Location 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China Report No.: AGC09272221202PA01 Page 6 of 15 6. TEST SETUP Report No.: AGC09272221202PA01 Page 7 of 15 7. TEST RESULTS 7.1. VSWR Frequency(MHz) VSWR 2402 1.168:1 2410 1.178:1 2450 1.163:1 2480 1.107:1 Report No.: AGC09272221202PA01 Page 8 of 15 7.2. GAIN AND EFFICIENCY Frequency(MHz) Efficiency(dB) Efficiency(%) Gain(dBi) 2400 -5.924 25.560 1.550 2410 -6.863 20.590 0.346 2420 -7.437 18.039 -0.251 2430 -6.831 20.742 0.588 2440 -5.736 26.691 1.892 2450 -5.442 28.557 2.200 2460 -5.695 26.944 1.841 2470 -6.047 24.845 1.465 2480 -5.795 26.332 1.572 2490 -5.872 25.865 1.327 2500 -5.737 26.684 1.575 Report No.: AGC09272221202PA01 Page 9 of 15 7.3. RADIATION PATTERN 2D POLAR RADIATION PATTERN FREQUENCY=2400MHZ FREQUENCY=2450MHZ FREQUENCY=2500MHZ Report No.: AGC09272221202PA01 Page 10 of 15 3D RADIATION PATTERN FREQUENCY…

Text truncated - open the document above for the full version.

Report No.:TZ0035260479PH01 Page 1 of 2 Test Setup Photos of the EUT Radiated Emission Below 1GHz Radiated Emission Above 1GHz Report No.:TZ0035260479PH01 Page 2 of 2 RF Conducted Test