2AVYXBASE20BASE STATION

User Manual United Automotive Electronic Systems Co., Ltd.(UAES) Base Station Table of contents 1 PRODUCT IDENTIFICATION ....................... 3 2 GENERAL PRODUCT DESCRIPTION ......... 4 2.1 MAIN FUNCTION AND PROPERTIES OF THE PRODUCT 4 2.2 INTENDED USE ........................................... 4 2.3 SAFETY AND WARNING NOTES ................ 5 2.4 LABELING OF THE PRODUCT .................... 6 2.5 DIMENSIONS AND WEIGHTS...................... 6 2.6 POWER CONSUMPTION / POWER OUTPUT6 2.7 INFORMATION ON DISPOSAL AND RECYCLING 6 3 SYSTEM DESCRIPTION .............................. 6 3.1 SYSTEM OF INTEREST (SOI) ...................... 6 3.2 HARDWARE AND SOFTWARE INTERFACES 6 4 TECHNICAL DATA WITH MEASURED VARIABLES AND MEASURING CONDITIONS 8 4.1 FUNCTIONS, FUNCTION STATES (MODES OF OPERATION), FUNCTIONAL CHARACTERISTICS AND BOUNDARY CONDITIONS 8 4.2 MECHANICAL CHARACTERISTICS ............ 8 4.3 ELECTRICAL CHARACTERISTICS ............. 8 4.4 CLIMATE CHARACTERISTICS .................... 8 4.5 CHEMICAL CHARACTERISTICS ................. 8 4.6 ACOUSTIC CHARACTERISTICS ................. 8 4.7 TRANSPORT, ASSEMBLY, START AND END OF OPERATION, STORAGE 8 5 SERIES-ACCOMPANYING TESTS .............. 9 6 TESTING ...................................................... 9 6.1 TESTING BY UAES .................................................................................................................. 9 6.2 TESTING BY CUSTOMER ............................................................................................................ 9 7 ASSESSMENT OF PRODUCTS RETURNED FROM THE FIELD 9 8 APPENDICES AND REFERENCES ............. 9 1 Product identification Product designation: BASE2.0 Type designation: BASE Customer: SGMW 2 General product description 2.1 Main function and properties of the product BASE station is an anti-theft controller integrated at the end of the coil,it interact data with Body Control Module(BCM),then BCM certificate with Engine Control Module(ECM),to implemente anti-theft function. UAES points out that the ASIL-classified requirements as per ISO 26262, their implementation and the assumptions made for this purpose are documented in chapter2.3. It is the customer’s responsibility to validate these documented requirements, their implementation and the assumptions made for this purpose. The customer must ensure that the UAES scope of delivery complies with the requirements on the functional safety within the overall system. 2.2 Intended use Provided that BASE2.0 is used within the conditions (environment, application, installation, loads) as described in this USER MANUAL and the corresponding agreed upon documents, UAES ensures that the product complies with the agreed properties. The product is considered fit for the intended use when the product successfully has passed the tests in accordance with the USER MANUAL and agreed upon documents. Agreements beyond this require the written approval by UAES. It is the responsibility of the customer to ensure the proper application of the product in the overall system/vehicle. UAES does not assume any responsibility for changes to the environment of the product that deviate from the USER MANUAL and the agreed upon documents. 2.3 Safety and warning notes A．Functional safety requirements： This product meets functional safety requirements (ISO 26262). ISO functional safety is an international standard for passenger vehicles, and the purpose is to prevent the potential risk caused by electrical and electronic system function failure. Generally, the requirements of functional safety is defined in DIA (Development Interface Agreement) reached by customers and UAES. If both sides don’t sign the agreement, the functional safety definition meets UAES Standard by default. Functional safety level of Base station is QM; B．Other safety warnings： 1) Preventing water from flowing into connector, it may cause short circuit between connectors. 2) The installation position of Base station should not be where dust gathers easily. A large amount of dust will affect the working reliability of Base station. 3) The installation position of Base station should be as far as possible from the high temperature place where ambient temperature makes shell itself exceed 85°C. At the same time, we should prevent heat released by surrounding parts from radiating Base station. 4) Installation Position of Base station should be far away from other parts with high electromagnetic and radiofrequency interference. 5) Base station should be installed firmly and reliable, no loosening should be allowed. 6) Base station should keep enough distance from other parts in passenger compartment to protect Base station and its wiring harness and make it easier to assemble during assembling the whole vehicle, in principle, the distance is no less than 10mm. 7) Installation position should be way from oil pollution、damp、spattering water. 8) Fixing of Base station wiring harness should be reliable, do not support wiring harness with Base station. 9) Extra mechanical vibration and external force impact should be avoided due to inappropriate installation position, meanwhile, installation position should not be at point of resonance of car body. 10) The installation position of Base station shouldn’t be near the place where it is likely to contact with accumulator or where acid and alkaline solution oozes easily. It also should be avoided to install Base station in the place vulnerable to corrosion. 11) It should be avoided to install Base station in the nearby place where it is likely to contact with accumulator positive terminal and ignition power terminal. 2.4 Labeling of the product The label of product BASE2.0 contains the items as follow, if customer requires special label contents or format, extra label design request shall be agreed by UAES. 2.5 Dimensions and weights 2.6 Power consumption / power output This product has multiple working modes, actual power capacity depend on applied condit…

Text truncated - open the document above for the full version.

Page: 1 of 4 (1) EUT Photo (2) EUT Photo Page: 2 of 4 (3) EUT Photo (4) EUT Photo Page: 3 of 4 (5) EUT Photo (6) EUT Photo Page: 4 of 4 (7) EUT Photo

Label Label Location

Page: 1 of 3 (1) EUT Photo (2) EUT Photo Page: 2 of 3 (3) EUT Photo (4) EUT Photo Page: 3 of 3 (5) EUT Photo

DEKRA Testing and Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Designation Number: CN1199 Test report No: 2032200R-RF-US-P20V01 TEST REPORT C Rules&Requlations FCC Exposure Evaluation Declaration Product Name BASE STATION Trademark SGMW Model and /or type reference BASE2.0 FCC ID 2AVYXBASE20 Applicant ́s name / address SAIC GM Wuling Automobile Co., Ltd. No.18 Hexi Road, Liuzhou City,Guangxi Zhuang Autonomous Region, China Test method requested, standard KDB 447498D01V06 FCC Part1.1310 Verdict Summary IN COMPLIANCE Documented By (name / position & signature) Kitty Li/ Project Assistant Tested by (name / position & signature) Frank He/ Technical Supervisor Approved by (name / position & signature) Jack Zhang/ Supervisor Date of issue 2020-06-29 Report template No 2032200R-RF-US-P20V01 DEKRA Testing and Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 Report no.: 2032200R-RF-US-P20V01 Page 2 / 15 INDEX page Competences and Guarantees ............................................................................................................................. 3 General conditions ............................................................................................................................................... 3 Environmental conditions ..................................................................................................................................... 3 Possible test case verdicts ................................................................................................................................... 4 Abbreviations ....................................................................................................................................................... 4 Document History ................................................................................................................................................ 5 Remarks and Comments ..................................................................................................................................... 5 1. General Information .................................................................................................................................... 6 1.1. EUT Description .......................................................................................................................................... 6 1.2. Antenna information .................................................................................................................................... 6 1.3. Mode of Operation ...................................................................................................................................... 7 1.4. Configuration of Tested System .................................................................................................................. 8 1.5. EUT Exercise Software ............................................................................................................................... 9 2. Test Environment ...................................................................................................................................... 10 3. Electric Field Strength ............................................................................................................................... 11 3.1 Test Equipment ......................................................................................................................................... 11 3.2 Test Setup ................................................................................................................................................ 11 3.3 Limit .......................................................................................................................................................... 12 3.4 Test Procedure ......................................................................................................................................... 13 3.5 Uncertainty ............................................................................................................................................... 14 3.6 Test Result ............................................................................................................................................... 15 DEKRA Testing and Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 Report no.: 2032200R-RF-US-P20V01 Page 3 / 15 COMPETENCES AND GUARANTEES DEKRA is a testing laboratory competent to carry out the tests described in this report. In order to assure the traceability to other national and international laboratories, DEKRA has a calibration and maintenance program for its measurement equipment. DEKRA guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated in the report and it is based on the knowledge and technical facilities available at DEKRA at the time of performance of the test. DEKRA is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Test Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA. GENERAL CONDITIONS 1. This report is only referred to the item that has undergone the test. 2. This report does not constitute or imply on its own an approval of the product by the Certification Bodies or Competen…

Text truncated - open the document above for the full version.

Test Report FCC Part15 Subpart C Product Name : BASE STATION Model No. : BASE2.0 FCC ID : 2AVYXBASE20 Applicant : SAIC GM Wuling Automobile Co., Ltd. Address : No.18 Hexi Road, Liuzhou City,Guangxi Zhuang Autonomous Region, China Date of Receipt : Mar. 31 , 2020 Test Date : Apr. 02 , 2020~ Apr. 24, 2020 Issued Date : Jun. 29, 2020 Report No. : 2032200R-RF-US-P06V05 Report Version : V1.1 The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the Issuing CB Testing Laboratory. The measurement result is considered in conformance with the requirement if it is within the prescribed limit, It is not necessary to calculate the uncertainty associated with the measurement result. This report is not used for social proof in China (or Mainland China) market. Report No.: 2032200R-RF-US-P06V05 Page: 2 of 27 Te s t R e p o r t C e r t i f i c a t i o n Issued Date : Jun. 29, 2020 Report No. : 2032200R-RF-US-P06V05 Product Name : BASE STATION Applicant : SAIC GM Wuling Automobile Co., Ltd. Address : No.18 Hexi Road, Liuzhou City,Guangxi Zhuang Autonomous Region, China Manufacturer : United Automotive Electronic Systems Co., Ltd. Address : No. 8, cheyuanheng fifth road yufeng area,Liuzhou City, Guangxi Province,516006,P.R. China. Factory : United Automotive Electronic Systems Co., Ltd. Address : No. 8, cheyuanheng fifth road yufeng area,Liuzhou City, Guangxi Province,516006,P.R. China. Model No. : BASE2.0 FCC ID : 2AVYXBASE20 EUT Voltage : DC 12V Test Voltage : DC 12V Brand Name : SGMW Applicable Standard : FCC CFR Title 47 Part 15 Subpart C; ANSI C63.10: 2013 Test Result : Complied Performed Location : DEKRA Testing and Certification (Suzhou) Co., Ltd. No.99 Hongye Rd., Suzhou Industrial Park, Suzhou, 215006, Jiangsu, China TEL: +86-512-6251-5088 / FAX: +86-512-6251-5098 FCC Designation Number: CN1199; IC Lab Code: 4075B Documented By : ( Adm. Specialist: Kitty Li ) Reviewed By : (Senior Project Manager: Frank He ) Approved By : (Engineering Supervisor: Jack Zhang) Report No.: 2032200R-RF-US-P06V05 Page: 3 of 27 TABLE OF CONTENTS Description Page 1. General Information ...................................................................................................... 5 1.1. EUT Description ............................................................................................................ 5 1.2. Antenna information ...................................................................................................... 6 1.3. Mode of Operation ........................................................................................................ 7 1.4. Tested System Details .................................................................................................. 8 1.5. Configuration of Tested System .................................................................................... 9 1.6. EUT Exercise Software ............................................................................................... 10 2. Technical Test ............................................................................................................. 11 2.1. Summary of Test Result .............................................................................................. 11 2.2. Test Environment ........................................................................................................ 11 3. Conducted Emission ................................................................................................... 12 3.1. Test Equipment ........................................................................................................... 12 3.2. Test Setup ................................................................................................................... 12 3.3. Limit ............................................................................................................................ 13 3.4. Test Procedure ............................................................................................................ 13 3.5. Uncertainty .................................................................................................................. 13 3.6. Test Result .................................................................................................................. 14 4. Radiated Emission ...................................................................................................... 15 4.1. Test Equipment ........................................................................................................... 15 4.2. Test Setup ................................................................................................................... 16 4.3. Limit ............................................................................................................................ 17 4.4. Test Procedure ............................................................................................................ 17 4.5. Uncertainty .................................................................................................................. 18 4.6. Test Result .................................................................................................................. 19 5. 20dB Occupied Bandwidth .......................................................................................... 23 5.1. Test Equipment ........................................................................................................... 23 5.2. Test Setup ................................................................................................................... 24 5.3. Limit ............................................................................................................................ 25 5.4. Test Procedure ............................................................................................................ 25 5.5. Uncertainty .…

Text truncated - open the document above for the full version.

Test Setup Photograph Description: Radiated Emission Test Setup for Below 30MHz Description: Radiated Emission Test Setup for 30MHz ~ 1GHz