2AVZWPTG0330-SACETarget-D

arge D T ACE AceTarget-D(Dynamic) Contents ------------------------------------- 1 Precau�ons ---------------------------------------------------------------- 2 Quick Start Guide -------------------------------------------------------- 3 Product Introduc�on---------------------------------------------------- 5 App. Opera�on Guide -------------------------------------------------- 6 1. Download App. 6 2. Connect Host 6 3. Run the App 7 4. System Func�on Guidance 8 5. System Setup Descrip�on 12 6. Game Se�ng 14 7. Game Racords . 17 Warranty -------------------------------------------------------------- 17 Table of contents 1 EN Contents AceTarget-D(Dynamic) Contents Item Contents Image Quan�ty Instruc�on Replacement for target ball replacment Length 1 meter 3 2 1 4 5 6 7 8 9 1 1 1 1 8 1 1 1 Rail sets AceTarget-D Non-slip mat For rail securing use M3x15 Screw 24 S�ck under the depending on the situa�on Motor Manual ACETECH Velcro Type C Charging cable PCB Charging Protect Shield To protect the charging connector been hit (6Pcs) Total length 90(cm) With 18650 Li-Ion Ba�ery 2 EN Precau�ons Please remove the ba�ery insula�on tab before the first �me use and charge it for at least 6 hours.(The maximum charging current is 500mA.) The target ball and connec�on part of AceTarget-D is consumable and not covered by the warranty. Consuming speed is varied by the frequence of usuage, and the velocity of the airso� gun. Bullet marks and dents on the target ball and face are normal and not be covered by the warranty. When using an AceTarget-D, the metal covered front should face to the shooter. There is no protec�on at the back side of the AceTarget. AceTarget can be charged when it is being used. Please avoid charging cable and portable charger being hit by BBs. Please turn off AceTarget when it is not in use. Recharge AceTarget for 30 minutes once in every 3 month to avoid ba�ery damage. 3 EN Quick Start Guide 1. Assemble the rails and screw the "PCB Charging Protect Shield on the rail. 2. Remove the ba�ery insula�on tab and charge AceTarget for at least 6 hours before use. Make sure the charging connectors of the target and rail are on the same side. And connect with type C charging cable . Remove Before 4 EN Turn off all the devices before se�ng the channel. And refer to page 5 for the se�ng details. Set up an Acetarget as "Host" and others are "Slave" If there are 2 sets of AceTarget systems in the same area, set the WIFI into differenct channels to avoid being bonded as one system. 4. Download the AceSo� App. on a mobile device and run the App a�er installa�on. 5. Connect the mobile device to any of AceTarget-S. Default password: 12345678 6. Start the games. For more details of the opera�on for the games, please refer to App. Opera�on Guide IOS Android Slave 1 2 3 4 ON DIP O I Off HostWifi Off 1 2 3 4 ON DIP O I Wifi 5 ZH The Moving ball target installed on the rail can be moved le� and right, and the rail extension length can be purchased, whole system execute by the smart device with WIFI connec�on, execute the AceSo� App opera�on and use. A. 4 digit Se�ng Bu�on: Toggle the switch to the symbol "ON" for binary "1". Toggle the switch to the digits "1 2 3 4" for binary "0" . The first digit sets the Host/Slave1 : Host0: Slave. Only one device is allowed to be Host, the rest devices shall be set as Slave as the default se�ng. The switches on 2, 3 and 4 can provide 8 independent WIFI channels. The same system must be set to the same channel. The default se�ng is channel "Acetarget1" B. Power Bu�on C. Speaker hole: The Speaker can beep and the volume can be adjusted by App D. TYPE-C Charging Port and Indicator LED E. Power port for rail F. Dimensions: 135mm x 113mm x 162mm G. Weight: 580g (including ba�ery) off on ON 1 2 3 4 A C B DE Digits ChannelDigits Channel Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Channel 8 6 EN App Opera�on Guide 1. Download App Scanning the QR code on the package to download AceSo� Appy or searching on App Store (Apple) or Play Store (Android). Android 5.0 / iOS 10.0 or later is recommended 2. Connect Host Turn WiFi of the mobile device on and connect to AceTarget(1-8). Password: 12345678. Host can only be connected by one mobile device only. IOS Android 7 EN 3:09 JouleACETECH RecordDevice 3. Run the App. Make sure the mobile device has connected to Wi-Fi of AceTarget. Run the App, the app displays the following picture. Tap the device figure to enter the game se�ng. Connect to your Acetech Device AceTarget 3:09 JouleACETECH RecordDevice Game--Shot Timer Round--1 Duration of game --15 Start Game Record AceTarget7 8 EN 3:09 JouleACETECH RecordDevice 3:09 JouleACETECH RecordDevice Game--Shot Timer Round--1 Duration of game--15 Start Game Record AceTarget7 4. System Func�on Guidance: Tap System Status Target Number: 24 Moving Target Number: 1 Coin Slot Machine: 1 Lighter BT 9 EN 3:09 JouleACETECH RecordDevice "Target Number: 13" means there are 13units of AceTarget-S in the system. "Moving Target Number: 1" means there are 1 units of AceTarget-D Tap Target Number to check the remaining ba�ery percentage of each AceTarget-S. When AceTarget-S connect to socket power and no ba�ery percentage be displayed 3:09 JouleACETECH RecordDevice System Status Target Number: 24 Moving Target Number: 1 Coin Slot Machine: 1 Lighter BT Target System Status 7 10 10 8 11 1 4 2 5 3 6 9 12 13 10 EN 3:09 System Status Target Number: 24 Moving Target Number: 1 Coin Slot Machine: 1 Lighter BT Tap Target Moving Target Number to see the mileage of AceTarget-D. Then, Tap the icon the selected AceTarget-D to turn on grenn light, and there will be a message on the App asking if you need to clear the mileage of AceTarget-D. The mileage record of the selected AceTarget-D will be erased a�er the requirment of the message is confirmed. 1415 15 3:09 Moving Target Mileage 46/104101mm111/130m 1415 3:09 Moving Target Mileage 46/104101mm111/130m Warning Do you to clear moving target mileag…

Text truncated - open the document above for the full version.

Declaration of Authorization We Name: Acetk Corp LTD. Address: 9F., No. 116, Sec. 1, Xintai 5th Rd., Xizhi Dist., City: New Taipei City Country: Taiwan (R.O.C.) Declare that: Name Representative of agent: Chenz Ker Agent Company name: MRT Technology (Taiwan) Co., Ltd Address: No. 38, Fuxing Second Rd., Guishan Dist., City: Taoyuan Country Taiwan is authorized to apply for Certification of the following product(s): Product description: ACETarget-D Type designation: ACETarget-D Trademark: Acetech FCC ID: 2AVZWPTG0330-S Validity/ expiry date: 2022/03/23 on our behalf. Date: 2022/02/24 Name: Eric Chang

Report No.: 2108TW2602-U1~U2 Product: ACETarget-D Brand Name: ACETECH Model Number: ACETarget-D 1 of 4 External Photograph (1) EUT Photo (2) EUT Photo Report No.: 2108TW2602-U1~U2 2 of 4 (3) EUT Photo (4) EUT Photo Report No.: 2108TW2602-U1~U2 3 of 4 (5) EUT Photo (6) EUT Photo Report No.: 2108TW2602-U1~U2 4 of 4 (7) USB Cable

Label Label location

Report No.: 2108TW2602-U1~U2 Product: ACETarget-D Brand Name: ACETECH Model Number: ACETarget-D 1 of 12 Internal Photograph (1) EUT Photo (2) EUT Photo Report No.: 2108TW2602-U1~U2 2 of 12 (3) EUT Photo (4) EUT Photo Report No.: 2108TW2602-U1~U2 3 of 12 (5) EUT Photo (6) EUT Photo Report No.: 2108TW2602-U1~U2 4 of 12 (7) EUT Photo (8) EUT Photo Report No.: 2108TW2602-U1~U2 5 of 12 (9) EUT Photo (10) EUT Photo Report No.: 2108TW2602-U1~U2 6 of 12 (11) EUT Photo (12) EUT Photo Report No.: 2108TW2602-U1~U2 7 of 12 (13) EUT Photo (14) EUT Photo Report No.: 2108TW2602-U1~U2 8 of 12 (15) EUT Photo (16) EUT Photo Report No.: 2108TW2602-U1~U2 9 of 12 (17) EUT Photo (18) EUT Photo Report No.: 2108TW2602-U1~U2 10 of 12 (19) EUT Photo (20) EUT Photo Report No.: 2108TW2602-U1~U2 11 of 12 (21) EUT Photo (22) EUT Photo Report No.: 2108TW2602-U1~U2 12 of 12 (23) EUT Photo (24) EUT Photo

MRT Technology (Taiwan) Co., Ltd Report No.: 2108TW2602-U3 Phone: +886-3-3288388 Report Version: 1.0 Fax: +886-3-3288918 Issue Date: 2022-02-08 Web: www.mrt-cert.com FCC ID: 2AVZWPTG0330-S Page Number: 1 of 6 Maximum Permissible Exposure FCC ID: 2AVZWPTG0330-S APPLICANT: Acetk Corp LTD. Application Type: Certification Product: ACETarget-D Model No.: ACETarget-D Trademark: FCC Rule Part(s): Part 2.1091 (Mobile) Test Date: September 29 ,2021 Tested By : ( Fran Chen ) Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. Report No.: 1910TW6501-U3 FCC ID: 2AVZWPTG0330-S Page Number: 2 of 6 Revision History Report No. Version Description Issue Date 2108TW2602-U3 1.0 Original Report 2022-02-08 Report No.: 1910TW6501-U3 FCC ID: 2AVZWPTG0330-S Page Number: 3 of 6 1. PRODUCT INFORMATION 1.1. Equipment Description Product Name ACETarget-D Model No. ACETarget-D Trademark: Supports Radios Spec. WiFi 2.4G: 802.11b/g/n-20 (1TX/1RX) Operating Frequency WiFi 2.4GHz: 2412 ~ 2462MHz Modulation 802.11b: DSSS, DBPSK, DQPSK, CCK 802.11g/n-20M: OFDM (BPSK, QPSK, 16QAM, 64QAM) Report No.: 1910TW6501-U3 FCC ID: 2AVZWPTG0330-S Page Number: 4 of 6 1.2. Antenna Description WiFi 2.4GHz Antenna Type N/A Antenna M/N N/A Antenna Gain 5.0dBi Report No.: 1910TW6501-U3 FCC ID: 2AVZWPTG0330-S Page Number: 5 of 6 2. MAXIMUM PERMISSIBLE EXPOSURE (MPE) 2.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 0.3-3.0 614 1.63 *100 6 3.0-30 1842/f 4.89/f *900/f 2 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- f/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 0.3-1.4 614 1.63 *100 30 1.34-30 824/f 2.19/f *180/f 2 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- f/1500 30 1500-100,000 -- -- 1.0 30 Note : (1) f= Frequency in MHz , (2) * = Plane-wave equivalent power density Calculation Formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 r = distance between observation point and center of the radiator in cm Under normal use condition, is at least 20cm away from the body of the user . So, this device is classified as Mobile Device. Report No.: 1910TW6501-U3 FCC ID: 2AVZWPTG0330-S Page Number: 6 of 6 2.2. Test Result Mode Frequency (MHz) Output Power to Antenna (dBm) Output Power to Antenna (mW) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) Wi-Fi 2412~2472 23.32 214.78 5.0 20 0.1351 1 So, device can comply with FCC radiation exposure requirement specified in the FCC Rule 2.1091. The End

MRT Technology (Taiwan) Co., Ltd Report No.: 2108TW2602-U2 Phone: +886-3-3288388 Report Version: 1.0 Fax: +886-3-3288918 Issue Date: 2022-02-08 Web: www.mrt-cert.com FCC ID: 2AVZWPTG0330-S Page Number: 1 of 91 FCC ID: 2AVZWPTG0330-S APPLICANT: Acetk Corp LTD. Application Type: Certification Product: ACETarget-D Model No.: ACETarget-D Trademark: FCC Classification: (DTS) Digital Transmission System FCC Rule Part(s): Part 15.247 Test Procedure(s): ANSI C63.10-2013 Received Date: August 10 ,2021 Test Date: September 4~29 ,2021 MEASUREMENT REPORT The test results only relate to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. Tested By : ( Peter Syu ) Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker) Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 2 of 91 Revision History Report No. Version Description Issue Date Note 2108TW2602-U2 1.0 Original Report 2022-02-08 Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 3 of 91 CONTENTS Description Page §2.1033 General Information ......................................................................................................... 5 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope .................................................................................................................................... 6 1.2. MRT Test Location ................................................................................................................ 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description .......................................................................................................... 7 2.2. Working Frequencies for this Report ..................................................................................... 8 2.3. Test Mode ............................................................................................................................. 9 2.4. Test Software ........................................................................................................................ 9 2.5. Test Configuration ............................................................................................................... 10 2.6. EMI Suppression Device(s)/Modifications ........................................................................... 10 2.7. Labeling Requirements ....................................................................................................... 10 3. DESCRIPTION of TEST ......................................................................................................... 11 3.1. Evaluation Procedure .......................................................................................................... 11 3.2. AC Line Conducted Emissions ............................................................................................ 11 3.3. Radiated Emissions ............................................................................................................ 12 4. ANTENNA REQUIREMENTS ................................................................................................ 13 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 14 6. MEASUREMENT UNCERTAINTY ......................................................................................... 15 7. TEST RESULT ...................................................................................................................... 16 7.1. Summary ............................................................................................................................. 16 7.2. 6dB Bandwidth Measurement ............................................................................................. 17 7.2.1. Test Limit ......................................................................................................................... 17 7.2.2. Test Procedure used ....................................................................................................... 17 7.2.3. Test Setting ..................................................................................................................... 17 7.2.4. Test Setup ....................................................................................................................... 17 7.2.5. Test Result ...................................................................................................................... 18 7.3. Output Power Measurement ................................................................................................ 21 7.3.1. Test Limit ......................................................................................................................... 21 7.3.2. Test Procedure Used ....................................................................................................... 21 7.3.3. Test Setting ..................................................................................................................... 21 7.3.4. Test Setup ....................................................................................................................... 21 7.3.5. Test Result of Output Power ............................................................................................ 22 7.4. Power Spectral Density Measurement ................................................................................ 23 7.4.1. Test Limit ..........................................…

Text truncated - open the document above for the full version.

Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 34 of 91 802.11n-20M CH06 (2437MHz) 802.11n-20M CH06 (2437MHz) 802.11n-20M CH011 (2462MHz) 802.11n-20M CH011 (2462MHz) 802.11n-20M CH011 (2462MHz) 802.11n-20M CH011 (2462MHz) Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 35 of 91 7.6. Radiated Spurious Emission Measurement 7.6.1. Test Limit All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table per Section 15.209. FCC Part 15 Subpart C Paragraph 15.209 Frequency [MHz] Field Strength [V/m] Measured Distance [Meters] 0.009 - 0.490 2400/F (kHz) 300 0.490 - 1.705 24000/F (kHz) 30 1.705 - 30 30 30 30 - 88 100 3 88 - 216 150 3 216 - 960 200 3 Above 960 500 3 7.6.2. Test Procedure Used KDB 558074 D01v05- Section 12.2.3 (quasi-peak measurements) KDB 558074 D01v05- Section 12.2.4 (peak power measurements) KDB 558074 D01v05- Section 12.2.5 (average power measurements) 7.6.3. Test Setting Peak Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = as specified in Table 1 3. VBW = 3MHz 4. Detector = peak 5. Sweep time = auto couple Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 36 of 91 6. Trace mode = max hold 7. Trace was allowed to stabilize Table 1 - RBW as a function of frequency Frequency RBW 9 ~ 150 kHz 200 ~ 300 Hz 0.15 ~ 30 MHz 9 ~ 10 kHz 30 ~ 1000 MHz 100 ~ 120 kHz > 1000 MHz 1 MHz Average Field Strength Measurements 1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest 2. RBW = 1MHz 3. VBW ≥ 1/T 4. De As an alternative, the instrument may be set to linear detector mode. Ensure that video filtering is applied in linear voltage domain (rather than in a log or dB domain). Some instruments require linear display mode in order to accomplish this. Others have a setting for Average-VBW Type, which can be set to “Voltage” regardless of the display mode 5. Detector = Peak 6. Sweep time = auto 7. Trace mode = max hold 8. Allow max hold to run for at least 50 times (1/duty cycle) traces Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 37 of 91 7.6.4. Test Setup 9kHz ~ 30MHz Test Setup: 30MHz ~ 1GHz Test Setup: Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 38 of 91 1GHz ~ 18GHz Test Setup: 18GHz ~25GHz Test Setup: Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 39 of 91 7.6.5. Test Result EUT ACETarget-D Date of Test 2021-09-27 Factor VULB 9162 Temp. / Humidity 25C /61% Polarity Horizontal Site / Test Engineer AC1 / Kaunaz Test Mode 802.11n-20MHz_TX_CH 6_ANT 0 Test Voltage By Notebook PC No Frequency (MHz) Reading (dBuV) C.F (dB/m) Measurement (dBuV/m) Margin (dB) Limit (dBuV/m) Height (cm) Angle (deg) Remark (QP/PK/AV) 1 54.250 14.20 21.27 35.47 -4.53 40.00 100 330 QP 2 * 59.100 17.90 20.38 38.28 -1.72 40.00 100 180 QP 3 107.600 22.70 18.82 41.52 -1.98 43.50 100 290 QP 4 119.240 24.30 17.35 41.65 -1.85 43.50 100 290 QP 5 299.660 17.33 21.49 38.83 -7.17 46.00 100 240 QP 6 356.890 17.14 23.34 40.48 -5.52 46.00 100 105 QP Note: 1. " *", means this data is the worst emission level. 2. C.F (Correction Factor) = Antenna Factor (dB)+ Cable Loss (dB). 3. Measurement (dBuV/m) = Reading(dBuV) + C.F (Correction Factor). 4. The emission levels of other frequencies are very lower than the limit and not show in test report. Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 40 of 91 EUT ACETarget-D Date of Test 2021-09-27 Factor VULB 9162 Temp. / Humidity 25C /61% Polarity Vertical Site / Test Engineer AC1 / Kaunaz Test Mode 802.11n-20MHz_TX_CH 6_ANT 0 Test Voltage By Notebook PC No Frequency (MHz) Reading (dBuV) C.F (dB/m) Measurement (dBuV/m) Margin (dB) Limit (dBuV/m) Height (cm) Angle (deg) Remark (QP/PK/AV) 1 47.460 10.28 21.93 32.21 -7.79 40.00 100 170 QP 2 * 59.100 17.80 20.38 38.18 -1.82 40.00 100 235 QP 3 107.600 16.11 18.82 34.94 -8.56 43.50 100 340 QP 4 119.240 17.25 17.35 34.60 -8.90 43.50 100 195 QP 5 348.160 9.16 23.17 32.32 -13.68 46.00 100 80 QP 6 644.980 4.79 28.53 33.32 -12.68 46.00 100 155 QP Note: 1. " *", means this data is the worst emission level. 2. C.F (Correction Factor) = Antenna Factor (dB)+ Cable Loss (dB). 3. Measurement (dBuV/m) = Reading(dBuV) + C.F (Correction Factor). 4. The emission levels of other frequencies are very lower than the limit and not show in test report. Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 41 of 91 EUT ACETarget-D Date of Test 2021-09-28 Factor BBHA 9120D & BBHA 9170 Temp. / Humidity 25C /61% Polarity Horizontal Site / Test Engineer AC1 / Kaunaz Test Mode 802.11b_TX_CH 1_ANT 0 Test Voltage By Notebook PC No Frequency (MHz) Reading (dBuV) C.F (dB/m) Measurement (dBuV/m) Margin (dB) Limit (dBuV/m) Height (cm) Angle (deg) Remark (QP/PK/AV) 1 * 4824.000 44.50 3.63 48.13 -25.87 74.00 150 360 Peak 2 7236.000 31.96 11.85 43.81 -30.19 74.00 150 360 Peak 3 9648.000 29.95 15.97 45.92 -28.08 74.00 150 360 Peak Note: 1. " *", means this data is the worst emission level. 2. C.F (Correction Factor) = Antenna Factor (dB)+ Cable Loss (dB) – Preamplifier(dB). 3. Measurement (dBuV/m) = Reading(dBuV) + C.F (Correction Factor). 4. The emission levels of other frequencies are very lower than the limit and not show in test report. Report No.: 2108TW2602-U2 FCC ID: 2AVZWPTG0330-S Page Number: 42 of 91 EUT ACETarget-D Date of Test 2021-09-28 Factor BBHA 9120D & BBHA 9170 Temp. / Humidity 25C /61% Polarity Vertical Site / Test Engineer AC1 / Kaunaz Test Mode 802.11b_TX_CH 1_ANT 0 Test Voltage By Notebook PC No Frequency (MHz) Reading (dBuV) C.F (dB/m) Measurement (dBuV/m) Margin (dB) Limit (dBuV/m) Height (cm) Angle (deg) Remark (QP/PK/AV) 1 * 4824.000 49.03 3.63 52.66 -21.34 74.00 150 360 Peak 2 7236.000 32.73 11.85 44.57 -29.43 74.00 150 360 Peak 3 9648.000 30.68 15.97 46.65 -27.35 74.00 150 360 Peak Note: 1. " *", means this data is the worst e…

Text truncated - open the document above for the full version.

Report No.: 2108TW2602-U1~U2 Product: ACETarget-D Brand Name: ACETECH Model Number: ACETarget-D 1 of 3 Test Photograph Description: Front View of Conducted Emission Test Setup Description: Back View of Conducted Emission Test Setup Report No.: 2108TW2602-U1~U2 2 of 3 Description: Radiated Emission Test Setup for below 1GHz Description: Radiated Emission Test Setup for above 1GHz Report No.: 2108TW2602-U1~U2 3 of 3 Description: Conducted Emission Test Setup