2AW3IF530Smart Diagnostic System

1 User Manual F530 Smart Diagnostic System Shenzhen Xtooltech Intelligent Co., Ltd. 2 3 Trademarks is trademark of Shenzhen Xtooltech Intelligent Co.,Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders. Copyright Information No part of this manual may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording, or otherwise without the prior written permission of Xtool. Disclaimer of Warranties and Limitation of Liabilities All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product. ※Before operating or maintaining this unit, please read this manual carefully paying extra attention to the safety warnings and precautions. Support & Service Official Website: www.xtooltech.com Tel: +86 755 21670995 or +86 755 86267858 (China) E-mail: [email protected] 4 Safety Information For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device. There are numerous procedures, techniques, tools, and parts required for servicing vehicles, as well as the skills of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician’s responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested. Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Be sure to read, understand, and follow all safety messages and instructions in this manual. Safety Instructions The safety messages herein cover situations Xtool is aware of at the time of publication. Xtool cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety. 5 Catalogue Chapter I Product Awareness ............................................................................................................ 6 1.1 Appearance and interface ......................................................................................................... 6 1.2 F530 Tablet technical parameters ............................................................................................ 6 Chapter II Product Usage .................................................................................................................. 7 2.1 Product connection mode ......................................................................................................... 7 Compliance Information ................................................................................................................... 8 6 Chapter I Product Awareness 1.1 Appearance and interface The F530 smart diagnostic system (referred to as the “Scan Tool”) is an advanced scanning tool. The advantage of this OBD-II (On-Board Diagnostics version 2) scanner is its comprehensive functions and its ability to quickly provide the user with more accurate diagnostic information. TABLET 1.Power Button 2.5.45-inch IPS 3.VGA Port 4.USB C Port 5.SD card slot 6.Product Identification Tag 1.2 F530 Tablet technical parameters OS：Linux CPU:Dual-core processor 1.2GHz Memory：128MB RAM & 64 GB on-board memory Screen: 5.45-inch IPS display Resolution: 720 x 1440 Battery Capacity: 3150mAh, 3.6V 7 Input voltage: 5V ⎓3A Working temperature: 0~40°C External dimensions：89.7mm x 179.9mm x 30.07mm (mm) Chapter II Product Usage 2.1 Product connection mode 2.1.1 Wired Connection To ensure proper communication between the tablet and the vehicle, the scan tool must be connected to the vehicle's OBD-II port. Follow these steps: 1. Power on the tablet. 2. Connect the main cable’s female adapter to the tablet first and tighten the captive screws. 3. Plug the 16-pin male connector of main cable into the vehicle’s DLC port. Turn on the vehicle's ignition and open the Diagnostic Application, on the tablet, to begin the diagnostic process. The connection method is shown in the figure below: Precautions for Diagnosis 1. The voltage range on the car: +9~+36V DC; 2. When testing some special functions, the operator must operate according to the prompts and meet the test conditions. For some models [special functions], the conditions that need to be met are: engine water temperature 80 °C~105 °C, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.; 3. The electronic control systems of different models are very complicated. If you encounter situations where it is impossible to test or a large amount of test data is abnormal, you can search for the ECU of the vehicle and select the men…

Text truncated - open the document above for the full version.

Report No.: AGC16626250804AP03 Page 1 of 20 INTERNAL PHOTOS Model: F530 OPEN VIEW OF EUT VIEW OF BATTERY (model: XBL18650-3150)-1 Report No.: AGC16626250804AP03 Page 2 of 20 VIEW OF BATTERY (model: 01DQ0180-03)-2 INTERNAL VIEW OF EUT (FIGURE 1) WIFI Antenna Report No.: AGC16626250804AP03 Page 3 of 20 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC16626250804AP03 Page 4 of 20 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) Report No.: AGC16626250804AP03 Page 5 of 20 INTERNAL VIEW OF EUT (FIGURE 6) INTERNAL VIEW OF EUT (FIGURE 7) Report No.: AGC16626250804AP03 Page 6 of 20 Model: DS5 OPEN VIEW OF EUT VIEW OF BATTERY (model: XBL18650-3150)-1 Report No.: AGC16626250804AP03 Page 7 of 20 VIEW OF BATTERY (model: 01DQ0180-03)-2 INTERNAL VIEW OF EUT (FIGURE 1) WIFI Antenna Report No.: AGC16626250804AP03 Page 8 of 20 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC16626250804AP03 Page 9 of 20 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) Report No.: AGC16626250804AP03 Page 10 of 20 INTERNAL VIEW OF EUT (FIGURE 6) INTERNAL VIEW OF EUT (FIGURE 7) Report No.: AGC16626250804AP03 Page 11 of 20 Model: E2 mini OPEN VIEW OF EUT VIEW OF BATTERY (model: XBL18650-3150)-1 Report No.: AGC16626250804AP03 Page 12 of 20 VIEW OF BATTERY (model: 01DQ0180-03)-2 INTERNAL VIEW OF EUT (FIGURE 1) WIFI Antenna Report No.: AGC16626250804AP03 Page 13 of 20 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC16626250804AP03 Page 14 of 20 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) Report No.: AGC16626250804AP03 Page 15 of 20 INTERNAL VIEW OF EUT (FIGURE 6) INTERNAL VIEW OF EUT (FIGURE 7) Report No.: AGC16626250804AP03 Page 16 of 20 Model: XT50V OPEN VIEW OF EUT VIEW OF BATTERY (model: XBL18650-3150)-1 Report No.: AGC16626250804AP03 Page 17 of 20 VIEW OF BATTERY (model: 01DQ0180-03)-2 INTERNAL VIEW OF EUT (FIGURE 1) WIFI Antenna Report No.: AGC16626250804AP03 Page 18 of 20 INTERNAL VIEW OF EUT (FIGURE 2) INTERNAL VIEW OF EUT (FIGURE 3) Report No.: AGC16626250804AP03 Page 19 of 20 INTERNAL VIEW OF EUT (FIGURE 4) INTERNAL VIEW OF EUT (FIGURE 5) Report No.: AGC16626250804AP03 Page 20 of 20 INTERNAL VIEW OF EUT (FIGURE 6) INTERNAL VIEW OF EUT (FIGURE 7) ****************************************End of Report*************************************

Report No.: AGC16626250804AP02 Page 1 of 3 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC16626250804AP02 Page 2 of 3 AC POWER LINE CONDUCTED TEST SETUP RF CONDUCTED TEST SETUP Report No.: AGC16626250804AP02 Page 3 of 3 Dynamic Frequency Selection (DFS) ****************************************End of Report*************************************

Page 1 of 27 FCC Test Report Report No.: AGC16626250804FR03 FCC ID : 2AW3IF530 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Smart Diagnostic System BRAND NAME : XTOOL, AutoProPAD MODEL NAME : F530, DS5, E2 mini, XT50V APPLICANT : Shenzhen Xtooltech Intelligent Co., Ltd. DATE OF ISSUE : Dec. 18, 2025 STANDARD(S) : FCC Part 15 Subpart E §15.407 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC16626250804FR03 Page 2 of 27 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Dec. 18, 2025 Valid Initial Release Report No.: AGC16626250804FR03 Page 3 of 27 Table of Contents 1. General Information ........................................................................................................................................ 4 2. Product Information ........................................................................................................................................ 5 2.1 Product Technical Description ................................................................................................................... 5 2.2 DFS Band Carrier Frequencies Operation ................................................................................................ 6 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 7 2.4 Test Methodology ...................................................................................................................................... 7 2.5 Description of Test Mode ........................................................................................................................... 7 2.6 Summary of Test Result ............................................................................................................................ 7 2.7 Antenna Requirement................................................................................................................................ 8 3. Test Environment ............................................................................................................................................ 9 3.1 Address of The Test Laboratory ................................................................................................................ 9 3.2 Test Facility ................................................................................................................................................ 9 3.3 Environmental Conditions ....................................................................................................................... 10 3.4 Measurement Uncertainty ....................................................................................................................... 10 3.5 List of Equipment Used ........................................................................................................................... 10 4. DFS Detection Thresholds and Radar Test Waveforms ............................................................................ 11 4.1 Provisions Applicable .............................................................................................................................. 11 4.2 DFS Devices Requirements .................................................................................................................... 12 4.3 DFS Detection Threshold Values ............................................................................................................ 13 4.4 Parameters of DFS Test Signals ............................................................................................................. 14 4.5 Measurement Setup (Block Diagram of Configuration) .......................................................................... 18 4.6 Measurement Procedure ......................................................................................................................... 19 4.7 Radar Waveform Calibration Plot ............................................................................................................ 21 4.8 Measurement Results ............................................................................................................................. 23 Appendix I: Photographs of Test Setup .......................................................................................................... 26 Appendix II: Photographs of Test EUT ........................................................................................................... 26 Report No.: AGC16626250804FR03 Page 4 of 27 1. General Information Applicant Shenzhen Xtooltech Intelligent Co., Ltd. Address 17&18/F, A2 Building, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, China Manufacturer Shenzhen Xtooltech Intelligent Co., Ltd. Address 17&18/F, A2 Building, Creative City, Liuxian Avenue, Nanshan District, Shenzhen, China Factory Bao'an branch of Shenzhen Xtooltech Intelligent Co., Ltd. Address 2,3,4/F building 12, Tangtou third industrial zone,Tangtou community, Shiyan street, Bao'an District, Shenzhen, China Product Designation Smart Diagnostic System Brand Name XTOOL, AutoProPAD Test Model F530 Series Model(s) DS5, E2 mini, XT50V Difference Description All the same except for the model name and software features. Date of receipt of test item Aug. 19, 2025 Date of Test Aug. 19, 2025 to Dec. 18, 2025 Deviation from Standard No any deviation from the test method Condition of Test Sample Normal Test Result Pass Test Report Form No AGCER-FCC-DFS-V1 Note: The test results of this report relate only to the tested sample identified in this report. Prepared By Jack Gui (Project Engineer) Dec. 18, 2025 Reviewed By Bibo Zhang (Reviewer) Dec. 18, 2025 Approved By Angela Li (Authorized Officer) Dec. 18, 2025 Report No.: AGC16626250804FR03 Page 5 of 27 2. Product Information 2.1 Product Technical Description Frequency Range U-NII 2A:5250MHz~5350…

Text truncated - open the document above for the full version.

Report No.: AGC16626250804FR02 Page 163 of 179 Radiated Emissions Test Results Above 1GHz EUT Name Smart Diagnostic System Model Name F530 Temperature 20.6°C Relative Humidity 51.1% Pressure 960hPa Test Voltage DC 3.6V by battery Operation Frequency U-NII 2A: 5250MHz~5350MHz Antenna Horizontal/Vertical Test Mode 802.11a_5320MHz Battery Model 1 XBL18650-3150 Radiated Emission Above 1GHz–Horizontal FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10640.0047.489.1456.6268.20-11.58 peak 15960.0043.5610.2253.7874.00-20.22 peak 15960.0033.4110.2243.6354.00-10.37 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Radiated Emission Above 1GHz–Vertical FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10640.0046.339.1455.4768.20-12.73 peak 15960.0042.6510.2252.8774.00-21.13 peak 15960.0032.4810.2242.7054.00-11.30 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Report No.: AGC16626250804FR02 Page 164 of 179 Radiated Emissions Test Results Above 1GHz EUT Name Smart Diagnostic System Model Name F530 Temperature 20.6°C Relative Humidity 51.1% Pressure 960hPa Test Voltage DC 3.6V by battery Operation Frequency U-NII 2A: 5250MHz~5350MHz Antenna Horizontal/Vertical Test Mode 802.11a_5260MHz Battery Model 2 01DQ0180-03 Radiated Emission Above 1GHz–Horizontal FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10520.0045.269.1454.4068.20-13.80 peak 15780.0041.2510.2251.4774.00-22.53 peak 15780.0032.8710.2243.0954.00-10.91 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Radiated Emission Above 1GHz–Vertical FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10520.0045.579.1454.7168.20-13.49 peak 15780.0041.1010.2251.3274.00-22.68 peak 15780.0032.1910.2242.4154.00-11.59 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Report No.: AGC16626250804FR02 Page 165 of 179 Radiated Emissions Test Results Above 1GHz EUT Name Smart Diagnostic System Model Name F530 Temperature 20.6°C Relative Humidity 51.1% Pressure 960hPa Test Voltage DC 3.6V by battery Operation Frequency U-NII 2A: 5250MHz~5350MHz Antenna Horizontal/Vertical Test Mode 802.11a_5300MHz Battery Model 2 01DQ0180-03 Radiated Emission Above 1GHz–Horizontal FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10600.0045.079.1454.2168.20-13.99 peak 15900.0041.1110.2251.3374.00-22.67 peak 15900.0032.5310.2242.7554.00-11.25 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Radiated Emission Above 1GHz–Vertical FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10600.0044.469.1453.6068.20-14.60 peak 15900.0039.3210.2249.5474.00-24.46 peak 15900.0030.4110.2240.6354.00-13.37 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Report No.: AGC16626250804FR02 Page 166 of 179 Radiated Emissions Test Results Above 1GHz EUT Name Smart Diagnostic System Model Name F530 Temperature 20.6°C Relative Humidity 51.1% Pressure 960hPa Test Voltage DC 3.6V by battery Operation Frequency U-NII 2A: 5250MHz~5350MHz Antenna Horizontal/Vertical Test Mode 802.11a_5320MHz Battery Model 2 01DQ0180-03 Radiated Emission Above 1GHz–Horizontal FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10640.0046.599.1455.7368.20-12.47 peak 15960.0042.4710.2252.6974.00-21.31 peak 15960.0032.5810.2242.8054.00-11.20 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Radiated Emission Above 1GHz–Vertical FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 10640.0045.919.1455.0568.20-13.15 peak 15960.0041.4710.2251.6974.00-22.31 peak 15960.0031.6510.2241.8754.00-12.13 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Result: Pass Note: 1. The amplitude of other spurious emissions from 1GHz to 25 GHz which are attenuated more than 20 dB below the permissible value need not be reported. 2. Factor = Antenna Factor + Cable loss - Amplifier gain, Margin=Level-Limit. 3. The “Factor” value can be calculated automatically by software of measurement system. 4. All test modes had been pre-tested. Refer to Chapter 5 of the report for details. Report No.: AGC16626250804FR02 Page 167 of 179 Test Result for Band edge Emission at Restricted bands EUT Name Smart Diagnostic System Model Name F530 Temperature 24.4°C Relative Humidity 40.0% Pressure 960hPa Test Voltage DC 3.6V by battery Battery Model 1 XBL18650-3150 802.11a_TX CH36_5180 MHz Item (Mark) Freq. MHz Reading dBμV Ant. Fac. dB/m PRM Factor dB Cable Loss dB Level dBμV/m Limit dBμV/m Margin dB Detector Pol. 1 5150 54.06 29.99 30.21 10.35 64.19 74 -9.81 Peak Horizontal 2 5150 38.22 29.99 30.21 10.35 48.345 54 -5.66 AV Horizontal 3 5150 51.87 29.99 30.21 10.35 62.002 74 -12.00 Peak Vertical 4 5150 36.29 29.99 30.21 10.35 46.42 54 -7.58 AV Vertical 802.11n40_TX CH38_5190 MHz Item (Mark) Freq. MHz Reading dBμV Ant. Fac. dB/m PRM Factor dB Cable Loss dB Level dBμV/m Limit dBμV/m Margin dB Detector Pol. 1 5150 51.51 29.99 30.21 10.35 61.643 74 -12.36 Peak Horizontal 2 5150 38.56 29.99 30.21 10.35 48.692 54 -5.31 AV Horizontal 3 5150 48.13 29.99 30.21 10.35 58.263 74 -15.74 Peak Vertical 4 5150 35.79 29.99 30.21 10.35 45.923 54 -8.08 AV Vertical 802.11ac80_TX 42_5210 MHz Item (Mark) Freq. MHz Reading dBμV Ant. Fac. dB/m PRM Factor dB Cable Loss dB Level dBμV/m Limit dBμV/m Margin dB Detector Pol. 1 5150 49.39 29.99 30.21 10.35 59.52 74 -14.48 Peak Horizontal 2 5150 38.56 29.99 30.21 10.35 48.69 54 -5.31 AV Horizontal 3 5150 45.75 29.99 30.21 10.35 55.882 74 -18.12 Peak Vertical 4 5150 35.73 29.99 30.21 10.35 45.862 54 -8.14 AV Vertical Report No.: AGC16626250804FR02 Page 168 of 179 802.11a_TX CH52_5320 MHz Item (Mark) Freq. MHz Reading dBμV A…

Text truncated - open the document above for the full version.

Report No.: AGC16626250804FR02 Page 107 of 179 10. Conducted Band Edge and Out-of-Band Emissions 10.1 Provisions Applicable Restricted bands Applicable to Limit 789033 D02 General UNII Test Procedures New Rules v02r01 Field strength at 3m (dBuV/m) PK: 74 AV: 54 Out of the restricted bands Applicable to EIRP Limit (dBm/MHz) Equivalent field Strength at 3m (dBuV/m) FCC 15.407(b)(1) PK: -27 PK: 68.2 15.407(b)(2) 15.407(b)(3) 15.407(b)(4) See Note 2 Note 1: The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: Note 2: All emissions shall be limited to a level of -27 dBm/MHz at 75 MHz or more above or below the band edge increasing linearly to 10 dBm/MHz at 25 MHz above or below the band edge, and from 25 MHz above or below the band edge increasing linearly to a level of 15.6 dBm/MHz at 5 MHz above or below the band edge, and from 5 MHz above or below the band edge increasing linearly to a level of 27 dBm/MHz at the band edge. 10.2 Measurement Procedure 1. Connect EUT RF output port to the Spectrum Analyzer through an RF attenuator 2. Set the Span = wide enough to capture the peak level of the in-band emission and all spurious emissions from the lowest frequency generated in the EUT up through the 10th harmonic. 3. RBW = 1MHz; VBW= 3MHz; Sweep = auto; Detector function = Peak. (Test frequency below 1GHz) 4. RBW = 1 MHz; VBW= 3 MHz; Sweep = auto; Detector function = Peak. (Test frequency Above 1GHz) 5. Set SPA Trace 1 Max hold, then View. 6. Antenna gain and path loss have been compensated to the Correction factor. 7. Mark the maximum useless stray point and compare it with the limit value to record the result. Report No.: AGC16626250804FR02 Page 108 of 179 10.3 Measurement Setup (Block Diagram of Configuration) Report No.: AGC16626250804FR02 Page 109 of 179 10.4 Measurement Results Test Graphs of Spurious Emissions outside of the 5.15-5.25 GHz band Test_Graph_802.11a_ANT1_5180_6Mbps_Frequency Band 1 Test_Graph_802.11a_ANT1_5180_6Mbps_Frequency Band 2 Report No.: AGC16626250804FR02 Page 110 of 179 Test_Graph_802.11a_ANT1_5180_6Mbps_Frequency Band 3 Test_Graph_802.11a_ANT1_5180_6Mbps_Frequency Band 4 Report No.: AGC16626250804FR02 Page 111 of 179 Test_Graph_802.11a_ANT1_5240_6Mbps_Frequency Band 1 Test_Graph_802.11a_ANT1_5240_6Mbps_Frequency Band 2 Report No.: AGC16626250804FR02 Page 112 of 179 Test_Graph_802.11a_ANT1_5240_6Mbps_Frequency Band 3 Test_Graph_802.11a_ANT1_5240_6Mbps_Frequency Band 4 Report No.: AGC16626250804FR02 Page 113 of 179 Test_Graph_802.11n40_ANT1_5190_MCS0_Frequency Band 1 Test_Graph_802.11n40_ANT1_5190_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 114 of 179 Test_Graph_802.11n40_ANT1_5190_MCS0_Frequency Band 3 Test_Graph_802.11n40_ANT1_5190_MCS0_Frequency Band 4 Report No.: AGC16626250804FR02 Page 115 of 179 Test_Graph_802.11n40_ANT1_5230_MCS0_Frequency Band 1 Test_Graph_802.11n40_ANT1_5230_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 116 of 179 Test_Graph_802.11n40_ANT1_5230_MCS0_Frequency Band 3 Test_Graph_802.11n40_ANT1_5230_MCS0_Frequency Band 4 Report No.: AGC16626250804FR02 Page 117 of 179 Test_Graph_802.11ac80_ANT1_5210_MCS0_Frequency Band 1 Test_Graph_802.11ac80_ANT1_5210_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 118 of 179 Test_Graph_802.11ac80_ANT1_5210_MCS0_Frequency Band 3 Test_Graph_802.11ac80_ANT1_5210_MCS0_Frequency Band 4 Report No.: AGC16626250804FR02 Page 119 of 179 Test Graphs of Spurious Emissions outside of the 5.25-5.35 GHz band Test_Graph_802.11a_ANT1_5260_6Mbps_Frequency Band 1 Test_Graph_802.11a_ANT1_5260_6Mbps_Frequency Band 2 Report No.: AGC16626250804FR02 Page 120 of 179 Test_Graph_802.11a_ANT1_5260_6Mbps_Frequency Band 3 Test_Graph_802.11a_ANT1_5260_6Mbps_Frequency Band 4 Report No.: AGC16626250804FR02 Page 121 of 179 Test_Graph_802.11a_ANT1_5320_6Mbps_Frequency Band 1 Test_Graph_802.11a_ANT1_5320_6Mbps_Frequency Band 2 Report No.: AGC16626250804FR02 Page 122 of 179 Test_Graph_802.11a_ANT1_5320_6Mbps_Frequency Band 3 Test_Graph_802.11a_ANT1_5320_6Mbps_Frequency Band 4 Report No.: AGC16626250804FR02 Page 123 of 179 Test_Graph_802.11n40_ANT1_5270_MCS0_Frequency Band 1 Test_Graph_802.11n40_ANT1_5270_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 124 of 179 Test_Graph_802.11n40_ANT1_5270_MCS0_Frequency Band 3 Test_Graph_802.11n40_ANT1_5270_MCS0_Frequency Band 4 Report No.: AGC16626250804FR02 Page 125 of 179 Test_Graph_802.11n40_ANT1_5310_MCS0_Frequency Band 1 Test_Graph_802.11n40_ANT1_5310_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 126 of 179 Test_Graph_802.11n40_ANT1_5310_MCS0_Frequency Band 3 Test_Graph_802.11n40_ANT1_5310_MCS0_Frequency Band 4 Report No.: AGC16626250804FR02 Page 127 of 179 Test_Graph_802.11ac80_ANT1_5290_MCS0_Frequency Band 1 Test_Graph_802.11ac80_ANT1_5290_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 128 of 179 Test_Graph_802.11ac80_ANT1_5290_MCS0_Frequency Band 3 Test_Graph_802.11ac80_ANT1_5290_MCS0_Frequency Band 4 Report No.: AGC16626250804FR02 Page 129 of 179 Test Graphs of Spurious Emissions outside of the 5.470-5.725 GHz band Test_Graph_802.11a_ANT1_5500_6Mbps_Frequency Band 1 Test_Graph_802.11a_ANT1_5500_6Mbps_Frequency Band 2 Report No.: AGC16626250804FR02 Page 130 of 179 Test_Graph_802.11a_ANT1_5500_6Mbps_Frequency Band 3 Test_Graph_802.11a_ANT1_5500_6Mbps_Frequency Band 4 Report No.: AGC16626250804FR02 Page 131 of 179 Test_Graph_802.11a_ANT1_5700_6Mbps_Frequency Band 1 Test_Graph_802.11a_ANT1_5700_6Mbps_Frequency Band 2 Report No.: AGC16626250804FR02 Page 132 of 179 Test_Graph_802.11a_ANT1_5700_6Mbps_Frequency Band 3 Test_Graph_802.11a_ANT1_5700_6Mbps_Frequency Band 4 Report No.: AGC16626250804FR02 Page 133 of 179 Test_Graph_802.11n40_ANT1_5510_MCS0_Frequency Band 1 Test_Graph_802.11n40_ANT1_5510_MCS0_Frequency Band 2 Report No.: AGC16626250804FR02 Page 134 of 179 Test_Graph_802.11n40_ANT1_5510_MCS0_Frequency Band 3 Test_Graph_802.11n40_ANT1_5510_MCS0_Frequency Band 4 Report No.: AGC1662…

Text truncated - open the document above for the full version.

Report No.: AGC16626250804FR02 Page 51 of 179 Test_Graph_802.11a_ANT1_5700_6Mbps_OBW Test_Graph_802.11n20_ANT1_5500_MCS0_OBW Report No.: AGC16626250804FR02 Page 52 of 179 Test_Graph_802.11n20_ANT1_5580_MCS0_OBW Test_Graph_802.11n20_ANT1_5700_MCS0_OBW Report No.: AGC16626250804FR02 Page 53 of 179 Test_Graph_802.11n40_ANT1_5510_MCS0_OBW Test_Graph_802.11n40_ANT1_5550_MCS0_OBW Report No.: AGC16626250804FR02 Page 54 of 179 Test_Graph_802.11n40_ANT1_5670_MCS0_OBW Test_Graph_802.11ac20_ANT1_5500_MCS0_OBW Report No.: AGC16626250804FR02 Page 55 of 179 Test_Graph_802.11ac20_ANT1_5580_MCS0_OBW Test_Graph_802.11ac20_ANT1_5700_MCS0_OBW Report No.: AGC16626250804FR02 Page 56 of 179 Test_Graph_802.11ac40_ANT1_5510_MCS0_OBW Test_Graph_802.11ac40_ANT1_5550_MCS0_OBW Report No.: AGC16626250804FR02 Page 57 of 179 Test_Graph_802.11ac40_ANT1_5670_MCS0_OBW Test_Graph_802.11ac80_ANT1_5530_MCS0_OBW Report No.: AGC16626250804FR02 Page 58 of 179 Test_Graph_802.11ac80_ANT1_5610_MCS0_OBW Test Graphs of Occupied Bandwidth and -26dB Bandwidth for band 5.745-5.825 GHz Test_Graph_802.11a_ANT1_5745_6Mbps_OBW Report No.: AGC16626250804FR02 Page 59 of 179 Test_Graph_802.11a_ANT1_5785_6Mbps_OBW Test_Graph_802.11a_ANT1_5825_6Mbps_OBW Report No.: AGC16626250804FR02 Page 60 of 179 Test_Graph_802.11n20_ANT1_5745_MCS0_OBW Test_Graph_802.11n20_ANT1_5785_MCS0_OBW Report No.: AGC16626250804FR02 Page 61 of 179 Test_Graph_802.11n20_ANT1_5825_MCS0_OBW Test_Graph_802.11n40_ANT1_5755_MCS0_OBW Report No.: AGC16626250804FR02 Page 62 of 179 Test_Graph_802.11n40_ANT1_5795_MCS0_OBW Test_Graph_802.11ac20_ANT1_5745_MCS0_OBW Report No.: AGC16626250804FR02 Page 63 of 179 Test_Graph_802.11ac20_ANT1_5785_MCS0_OBW Test_Graph_802.11ac20_ANT1_5825_MCS0_OBW Report No.: AGC16626250804FR02 Page 64 of 179 Test_Graph_802.11ac40_ANT1_5755_MCS0_OBW Test_Graph_802.11ac40_ANT1_5795_MCS0_OBW Report No.: AGC16626250804FR02 Page 65 of 179 Test_Graph_802.11ac80_ANT1_5775_MCS0_OBW Report No.: AGC16626250804FR02 Page 66 of 179 Test Graphs of DTS Bandwidth for band 5.725-5.85 GHz Test_Graph_802.11a_ANT1_5745_6Mbps_DTSBW Test_Graph_802.11a_ANT1_5785_6Mbps_DTSBW Report No.: AGC16626250804FR02 Page 67 of 179 Test_Graph_802.11a_ANT1_5825_6Mbps_DTSBW Test_Graph_802.11n20_ANT1_5745_MCS0_DTSBW Report No.: AGC16626250804FR02 Page 68 of 179 Test_Graph_802.11n20_ANT1_5785_MCS0_DTSBW Test_Graph_802.11n20_ANT1_5825_MCS0_DTSBW Report No.: AGC16626250804FR02 Page 69 of 179 Test_Graph_802.11n40_ANT1_5755_MCS0_DTSBW Test_Graph_802.11n40_ANT1_5795_MCS0_DTSBW Report No.: AGC16626250804FR02 Page 70 of 179 Test_Graph_802.11ac20_ANT1_5745_MCS0_DTSBW Test_Graph_802.11ac20_ANT1_5785_MCS0_DTSBW Report No.: AGC16626250804FR02 Page 71 of 179 Test_Graph_802.11ac20_ANT1_5825_MCS0_DTSBW Test_Graph_802.11ac40_ANT1_5755_MCS0_DTSBW Report No.: AGC16626250804FR02 Page 72 of 179 Test_Graph_802.11ac40_ANT1_5795_MCS0_DTSBW Test_Graph_802.11ac80_ANT1_5775_MCS0_DTSBW Report No.: AGC16626250804FR02 Page 73 of 179 9. Power Spectral Density Measurement 9.1 Provisions Applicable Operation Band EUT Category LIMIT U-NII-1 Outdoor Access Point 17dBm/ MHz Fixed point-to-point Access Point 17dBm/ MHz Indoor Access Point 17dBm/ MHz Client devices 11dBm/ MHz U-NII-2A / 11dB…

Text truncated - open the document above for the full version.