2AW8R-LKB01Cordless Air Compressor

REV 05/25/21 Cordless Air Compressor Operator's Manual WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Save these instructions in a safe place and on hand so that they can be read when required. Keep these instructions to assist in future servicing. AIR COMPRESSOR SAFETY WARNINGS For your own safety, always follow these basic precautions when using this appliance. 1. Read the user Manual carefully for operating instructions. Read all instruc- tions in this manual before use. 2. DO NOT use attachments other than those available from the manufacturer. 3. DO NOT alter this product in any manner; doing so is dangerous and will void all warranties. 4. DO NOT operate under the influence of drugs or alcohol. 5. DO NOT continue to use this product in the event of mechanical or electrical failure. 6. DO NOT exceed the pressure rating of any component in the system. 7. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. The floor must not be slippery from lubricants, wax dust or anything else that may cause slips and falls. 8. Do not operate air compressors in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. 9. Do not expose air compressors to rain or wet conditions. Water entering an air compressor will increase the risk of electric shock. 10. Additional safety protection will be required in some environments. For example, hearing protection, safety hard hats, and eye protection may be required at the users discretion. 11. The battery must be removed before any repairs. 12. When servicing a productfollow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of injury. 13. Service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury and will void the warranty. 14. Keep hose away from sharp objects, chemical spills, oil, solvents, and wet floors. 15. DO NOT allow children to operate this unit. 16. Store idle air compressors out of the reach of children and other untrained persons. Air compressors are dangerous in the hands of untrained users. 17. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the product’s operation. If damaged, have the air compressor serviced before using. Many accidents are caused by poorly maintained products. 18. Keep the exterior of the air compressor dry, clean, and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean the unit. Following this rule will reduce the risk of deterioration of the enclosure plastic. 19. Risk of Bursting. Do not adjust the regulator output pressure greater than he marked maximum pressure of attachment accessory. Do not use at a pressure greater than 135 psi. 20. Inspect tanks yearly for rust or other imperfections that could cause them to become unsafe. Never weld or drill holes in the air tanks. 21. Use the air compressor only for its intended use. Do not alter or modify the unit from the original design or function. 22. Always be aware that misuse and improper handling of this product can cause injury to yourself and others. 23. Do not operate this air compressor if it does not contain a legible warning label. 24. Do not continue to use a tool or hose that leaks air or does not function properly. 25. Always disconnect the air supply, turn the unit off, and remove the battery packs before adjustmenting, servicing a product, or when a product is not in use. 26. Do not attempt to pull or carry the air compressor by the hose. 27. Always follow all safety rules recommended by the manufacturer of your air tool, in addition to all safety rules for the air compressor. Following this rule will reduce the risk of serious personal injury. 28. Never direct a jet of compressed air toward people or animals. Take care not to blow dust and dirt towards yourself or others. Following this rule will reduce the risk of serious injury. 29. Do not use this air compressor to spray chemicals. Your lungs can be damaged by inhaling toxic fumes. A respirator may be necessary for dusty environments or when spraying paint. Do not carry while painting. 30. Never store a tool with air hose connected. Storing the tool with air connect- ed can result in unexpected firing and possible serious personal injury. 31. Recharge battery only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 32. When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 33. If battery housing is damaged or punctured, liquid may be ejected from the battery. Avoid contact with any battery liquid. If contact accidentally occurs, wash immediately with water. If liquid contacts eyes flush eyes with water, and seek immediate medical help. Liquid ejected from the battery may cause irritation or burns. 34. Do not place batteries near fire or heat. This will reduce the risk of explosion and possibly injury. 35. Do not crush, drop, or damage the battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately. 36. Do not use a battery pack that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury. 37. DO NOT discard the…

Text truncated - open the document above for the full version.

Intradin (Shanghai) Machinery Co., Ltd Agent Authorization Company: Intradin (Shanghai) Machinery Co., Ltd Address: No. 118, Duhui Road, Minhang District, Shanghai, China Product Name: Cordless Air Compressor Trade Mark: N/A Model Number(s): LKB01 FCC ID: 2AW8R-LKB01 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2021-07-06 Name: Mark Lee Title: Lab Manager Company: Intradin (Shanghai) Machinery Co., Ltd

Intradin (Shanghai) Machinery Co., Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-07-06 Subject; Request for Confidentiality FCC ID: 2AW8R-LKB01 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description BOM Software Security Requirements In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name / Title: Mark Lee / Lab Manager Company: Intradin (Shanghai) Machinery Co., Ltd Address: No. 118, Duhui Road, Minhang District, Shanghai, China Phone: 86-21-6490 8190 Fax:/ E-Mail: [email protected]

Page 1 of 1 Rev.2.0 Intradin (Shanghai) Machinery Co., Ltd WIFI Channel 12 and 13 Declaration Letter We declare the equipment identified below with regards to Channel 12 and 13 capabilities for FCC ID: 2AW8R-LKB01 Declaration Product hardware does not have the capability to operate on Channel 12 and 13. Product hardware has the capability to operate on Channel 12 and 13. However, these two channels will be disabled via software and will not be accessible to user. Product hardware has the capability to operate on Channel 12 and 13. However, all the operated channels can’t be changed in the RF parameter via software. All channels have complied with all of the requirements sets out in FCC Part 15.247. Product hardware has the capability to operate on WiFi Channel 12 and 13, and meets the requirements of KDB 594280 D01 v02r01. Please note: 1.) By default, this device operates in a mode that is compliant with the U.S. requirements. 2.) This device will also use supplemental information such as geo- location data to determine that it is operating outside the U.S., if necessary, to change its power. Such supplemental data will be derived from the following: Global Navigation Satellite System (GNSS)7 sensors in the device Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received from a CMRS9 carrier and received directly by a receiver on the device Country information derived from multiple adjacent access points (for example using IEEE Std 802.11d provisions) may be permitted on case-by- case basis Other suitable geo-location data based on IP addresses or other reliable source. Name / Title: Mark Lee / Lab Manager Signature: Phone: 86-21-6490 8190 Email: [email protected] Date: 2021-07-06

FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 1 Fig. 2 FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 3 Fig. 4 FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 5 Fig. 6 FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 7 Fig. 8

_____________________________________________________________________________________________________ LABEL AND LOCATION (Size: L11.8cm x 4.3cm) Label Location

FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 1 Fig. 2 FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 3 Fig. 4 FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 5 Fig. 6 Antenna FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 7 Fig. 8 FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 Fig. 9 Fig. 10

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong RF Exposure evaluation Report Reference No...................... : FCC ID. ............................................ : GTS20210609019-1-2 2AW8R-LKB01 Compiled by ( position+printed name+signature) . : File administrators Peter Xiao Supervised by ( position+printed name+signature) . : Test Engineer Oliver Ou Approved by ( position+printed name+signature) . : Manager Simon Hu Date of issue .................................... : Jun.22, 2021 Representative Laboratory Name . : Shenzhen Global Test Service Co.,Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong Applicant’s name ............................ : Intradin (Shanghai) Machinery Co., Ltd Address ............................................ : No. 118, Duhui Road, Minhang District, Shanghai, China Test specification ........................... : Standard ........................................... : 47CFR §1.1310 47CFR §2.1091 KDB447498 D01 General RF Exposure Guidance v06 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ...................................... : Dated 2014-12 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : Cordless Air Compressor Trade Mark ....................................... : N/A Manufacturer .................................... : Intradin (Shanghai) Machinery Co., Ltd Model/Type reference ...................... : LKB01 Listed Models .................................. : N/A Modulation Type ............................... : IEEE 802.11b/802.11g/802.11n Operation Frequency........................ : From 2412MHz to 2462MHz Hardware Version ............................ : N/A Software Version .............................. : N/A Rating ............................................... : DC 48V by Battery Result ............................................... : PASS Report No.: GTS20210609019-1-2 Page 2 of 11 T E S T R E P O R T Test Report No. : GTS20210609019-1-2 Jun.22, 2021 ______________________________________________________________________________________________ Date of issue Equipment under Test : Cordless Air Compressor Model /Type : LKB01 Listed model : N/A Applicant : Intradin (Shanghai) Machinery Co., Ltd Address : No. 118, Duhui Road, Minhang District, Shanghai, China Manufacturer : Intradin (Shanghai) Machinery Co., Ltd Address : No. 118, Duhui Road, Minhang District, Shanghai, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20210609019-1-2 Page 3 of 11 Contents 1. SUMMARY ................................................................................................................................................................. 4 1.1 EUT CONFIGURATION ........................................................................................................................................................ 4 1.2 PRODUCT DESCRIPTION ..................................................................................................................................................... 4 2. TEST ENVIRONMENT ................................................................................................................................................. 5 2.1 ADDRESS OF THE TEST LABORATORY ..................................................................................................................................... 5 2.2 TEST FACILITY .................................................................................................................................................................. 5 2.3 ENVIRONMENTAL CONDITIONS ............................................................................................................................................ 5 2.4 STATEMENT OF THE MEASUREMENT UNCERTAINTY .................................................................................................................. 5 3. METHOD OF MEASUREMENT .................................................................................................................................... 6 3.1 APPLICABLE STANDARD ...................................................................................................................................................... 6 3.2 REQUIREMENT ................................................................................................................................................................. 6 3.3 LIMIT ............................................................................................................................................................................. 6 3.4 MPE CALCULATION METHOD ............................................................................................................................................. 7 3.5 ANTENNA INFORMATION ................................................................................................................................................... 7 4. CONDUCTED POWER RESULTS .............................................................................…

Text truncated - open the document above for the full version.

Shenzhen Global Test Service Co.,Ltd. No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ..................... : FCC ID. ............................................ : GTS20210609019-1-1 2AW8R-LKB01 Compiled by ( position+printed name+signature) .. : File administrators Peter Xiao Supervised by ( position+printed name+signature) .. : Test Engineer Oliver Ou Approved by ( position+printed name+signature) .. : Manager Simon Hu Date of issue ..................................... : Jun.22, 2021 Representative Laboratory Name .: Shenzhen Global Test Service Co.,Ltd. Address ............................................ : No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong,China Applicant’s name ............................ : Intradin (Shanghai) Machinery Co., Ltd Address ............................................ : No. 118, Duhui Road, Minhang District, Shanghai, China Test specification ...........................: Standard ........................................... : FCC Part 15.247: Operation within the bands 902-928 MHz, 2400- 2483.5 MHz and 5725-5850 MHz ANSI C63.10-2013 KDB558074 D01 DTS Meas Guidance v05r02 TRF Originator .................................. : Shenzhen Global Test Service Co.,Ltd. Master TRF ....................................... : Dated 2014-12 Shenzhen Global Test Service Co.,Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Global Test Service Co.,Ltd. is acknowledged as copyright owner and source of the material. Shenzhen Global Test Service Co.,Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .....................: Cordless Air Compressor Trade Mark ....................................... : N/A Manufacturer .................................... : Intradin (Shanghai) Machinery Co., Ltd Model/Type reference....................... : LKB01 Listed Models .................................. : N/A Operation Frequency ........................ : From 2412MHz to 2462MHz Hardware Version ............................ : N/A Software Version .............................. : N/A Rating ............................................... : DC 48V by Battery Result................................................ : PASS Report No.: GTS20210609019-1-1 Page 2 of 40 T E S T R E P O R T Test Report No. : GTS20210609019-1-1 Jun.22, 2021 ____________________________________________________________________________________ Date of issue Equipment under Test : Cordless Air Compressor Model /Type : LKB01 Listed model : N/A Applicant : Intradin (Shanghai) Machinery Co., Ltd Address : No. 118, Duhui Road, Minhang District, Shanghai, China Manufacturer : Intradin (Shanghai) Machinery Co., Ltd Address : No. 118, Duhui Road, Minhang District, Shanghai, China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: GTS20210609019-1-1 Page 3 of 40 Contents 1. TEST STANDARDS ......................................................................................................................................... 4 2. SUMMARY ....................................................................................................................................................... 5 2.1. General Remarks ................................................................................................................................... 5 2.2. Product Description ................................................................................................................................ 5 2.3. Equipment Under Test ........................................................................................................................... 6 2.4. Short description of the Equipment under Test (EUT) ........................................................................... 6 2.5. EUT operation mode .............................................................................................................................. 6 2.6. Block Diagram of Test Setup ................................................................................................................. 6 2.7. Related Submittal(s) / Grant (s) ............................................................................................................. 7 2.8. EUT Exercise Software .......................................................................................................................... 7 2.9. Special Accessories ............................................................................................................................... 7 2.10. External I/O Cable ................................................................................................................................ 7 2.11. Modifications ........................................................................................................................................ 7 3. TEST ENVIRONMENT ..................................................................................................................................... 8 3.1. Address of the test laboratory ................................................................................................................ 8 3.2. Test Facility ............................................................................................................................................ 8 3.3. Environmental conditions .....................…

Text truncated - open the document above for the full version.

FCC ID: 2AW8R-LKB01 IC: 26378-LKB01 _______________________________________________________________________________________________ Page 1 of 1 1. TEST SETUP PHOTOGRAPHS 1.1. Photo of Radiated Emissions Measurement Fig. 1 Fig. 2