2AWD4-ECHL-7747Motorized Treadmill, Stride-50-RCX

Owner’s Manual ers A THANK YOU Thanks for purchasing this product. The product will help you keep fitter, healthier and better in a very easy way. Read and follow all warnings and instructions. For consumer fitness equipment, ensure that proper instructions are obtained prior to use. IMPORTANT SAFETY INSTRUCTION  Care should be taken in mounting or dismounting the treadmill. Before mounting or dismounting, bring the machine to a complete stop. Read all instructions before using the treadmill For HOUSEHOLD USE ONLY. SAVE THESE INSTRUCTIONS.  When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using (this appliance).  This treadmill is designed for home use for jogging, running workout purpose; Don’t use the treadmill for other exercises which has not relation to treadmill.  Place the treadmill indoors to avoid any water and no heavy stuff.  The treadmill shall be installed on a stable and levelled base.  When using the fitness device, wear comfortable clothing and preferably sports or aerobic shoes.  Keep Children away from the treadmill to avoid any accident.  Prior to use, inspect the treadmill to ensure there is no incorrect, worn, or loose components and all components are in good condition and tighten properly. Refer to treadmill maintenance in last chapter for more information.  Refer to treadmill maintenance keep the top side of the moving surface clean and dry.  Refer to treadmill maintenance to replace defective components immediately and/or keep the equipment out of use until repair and pay special attention to com- ponents most susceptible to wear.  Refer to treadmill maintenance for method of adjusting the tension and the lateral position of the running surface.  The safety and integrity designed into the machine can only be maintained when the treadmill is regularly examined for damage and repaired. It is the sole responsi- bility of the user/owner or facility operator to ensure that regular maintenance is performed. Worn or damaged components shall be replaced immediately, or the treadmill removed from service until the repair is made. Only manufacturer-supplied or-approved components shall be used to maintain and repair the treadmill.  The safety level of the equipment can be maintained only if it is examined regularly for damage and wear.  No overload to give damages to motor, controller, roller and running belt . Make routine maintenance to the treadmill.  Keep less dust indoors and keep a certain extent of humidity to avoid interference of console and controller.  For home use treadmill, keep the treadmill continuous running no more than 2 hours. Indoor use, class HC.  Keep good air circulation when running.  The recommended minimum clearance required around each treadmill for access to and passage around shall be 500 mm (19.7 in.) on each side of the treadmill. There shall be 2000x1000mm safe space at the treadmill end when running.  The minimum clearance area behind the treadmill shall be: 2.0 m (78.7 in.). This clearance shall encompass the entire width of the treadmill or the entire length of a row of treadmills. This clearance zone shall be free of all obstructions.  Read, understand, and test the emergency stop procedures before use. Refer to how to use emergency key chapter for more information.  Do not exceed maximum user weight 130KG.  Stop running if any discomfort and consult the doctor.  “WARNING! Heart rate monitoring systems may be inaccurate. Over exercising may result in serious injury or death. If you feel faint stop exercising immediately”;  Keep the silicone oil bottle out of reach from children and avoid eating by mistake.  After workout, don’t jump out of the treadmill directly, so to prevent accident.  Pull out of the power plug gently from the socket.  Correct biomechanical positioning of the user on treadmill is important for healthy workout. For correct workout suggestions, please refer to HOW TO USE THE PRODUCT chapter. Injuries to health may result from incorrect or excessive train- ing.  During workout, stop use the machine if anything wrong and cut the power immedi- ately.  The value of the A-weighted emission sound pressure level at the trainer’s ear: 68.4dB.  Noise emission under load is higher than without load.  Ask local distributor to handle any issue or provide service. It’s not allowed to dis- mantle the components personally. if any of the adjustment devices are left project- ing, they could interfere with the user’s movement.  This treadmill is 120KGS.  DANGER – To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet immediately after using and before cleaning.  WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:  1) An appliance should never be left unattended when plugged in. Unplug from out- let when not in use, and before putting on or taking off parts.  2) Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to persons.  3) This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person re- sponsible for their safety. Keep children under the age of 13 away from this ma- chine.  4) Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.  5) Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the ap- pliance to a service center for examination and repair.  6) Do not carry this appliance by supply cord or use cord as a handle.  7) Keep the cord away from heated surfaces.  8) Never operate the appliance with the air openings block…

Text truncated - open the document above for the full version.

Applicant Declaration QSF27-14-04 Rev 1.1 Jan 17, 2024 Page 1 of 1 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Echelon Fitness Multimedia LLC Address 605 Chestnut Street Suite 700, Chattanooga, Tennessee, 37450, United States FRN 0029566114 Grantee Code 2AWD4 FCC ID 2AWD4-ECHL-7747 Authorized Contact Name Ryan Judd Contact Email [email protected] Contact Phone 4234029010 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List Echelon Fitness Multimedia LLC (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Echelon Fitness Multimedia LLC (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date: Date: 2024/8/14 Print Name: Ryan Judd Title: - *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

UNITED STATES DESIGNATED AGENT LETTER Date: 2024/8/14 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant U.S. designated agent Company Name: Echelon Fitness Multimedia LLC Company Name: Echelon Fitness Multimedia LLC FRN: 0029566114 FRN: 0029566114 Grantee Code: 2AWD4 Contact Name: Ryan Judd Contact Name Ryan Judd Address: 605 Chestnut Street Suite 700 Address: 605 Chestnut Street Suite 700 City/Province/Zip: Chattanooga, Tennessee, 37450 City/Province/Zip: Chattanooga, Tennessee, 37450 Telephone: 4234029010 Telephone: 4234029010 Fax: 4234029010 Fax: 4234029010 Email: [email protected] Email: [email protected] Applicable Equipment: FCC ID: 2AWD4-ECHL-7747 ATTN: Director of Certification: We, Echelon Fitness Multimedia LLC understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, Echelon Fitness Multimedia LLC acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Applicant U.S. designated agent Name (Printed): Ryan Judd Name (Printed): Ryan Judd Title: - Title: - Signature: Signature:

Echelon Fitness Multimedia LLC Authority letter FCC Date: 2024/8/14 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AWD4-ECHL-7747 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Bonnie Liao in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with applicant company FCC. This authorization is valid until further written notice from the applicant. Name (Printed): Ryan Judd Title: - Signature: On behalf of Company: Echelon Fitness Multimedia LLC

Echelon Fitness Multimedia LLC Confidential letter FCC To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Echelon Fitness Multimedia LLC 605 Chestnut Street Suite 700 Chattanooga, Tennessee, 37450, United States Regarding: Confidentiality Request regarding application for FCC ID: 2AWD4-ECHL-7747 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Ryan Judd Title: - Signature: On behalf of Company: Echelon Fitness Multimedia LLC

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 1 of 3 Appendix External Photos for GZCR2408001006HS SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 2 of 3 EUT Constructional Details (EUT Photos) STRIDE-RCX SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 3 of 3 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 1 of 12 Appendix Internal Photos for GZCR2408001006HS SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 2 of 12 EUT Constructional Details (EUT Photos) STRIDE-RCX SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 3 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 4 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 5 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 6 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 7 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 8 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 9 of 12 BLE ANT SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 10 of 12 BT Classic ANT SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 11 of 12 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 12 of 12 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240800100603 Page: 1 of 9 FCC ID: 2AWD4-ECHL-7747 Ricky Liu Manager RF EXPOSURE EVALUATION REPORT Application No.: GZCR2408001006HS Applicant:Echelon Fitness Multimedia, LLC Address of Applicant:605 Chestnut Street, Suite 700, Chattanooga,TN 37450 Manufacturer:Oma Fitness Equipment Co., Ltd Address of Manufacturer:93 Tai An Road South, Yang'e Village , Lunjiao Town, Shunde, Foshan, 528000, Guangdong, China Factory:Oma Fitness Equipment Co., Ltd Address of Factory:93 Tai An Road South, Yang'e Village , Lunjiao Town, Shunde, Foshan, 528000, Guangdong, China Product Name:Motorized Treadmill, Stride-50-RCX Model No.: STRIDE-RCX Trade Mark:Echelon Standard(s) : KDB 447498 D01 V06 47 CFR Part 1.1310 Date of Receipt: 2024-06-06 Date of Evaluation: 2024-07-01 to 2024-08-22 Date of Issue: 2024-09-19 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240800100603 Page: 2 of 9 Revision Record VersionReport No.DateRemark 01GZCR2408001006032024-09-19Original Authorized for issue by: Luke Lin/Project Engineer Vico Cui/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240800100603 Page: 3 of 9 2Evaluation Summary ItemStandardMethodRequirementResult RF Exposure KDB447498D01 General RF Exposure Guidance v06 KDB447498D01 General RF Exposure Guidance v06 47 CFR Part 1.1310Pass Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240800100603 Page: 4 of 9 3Contents Page 1Cover Page...............................................................................................................................................1 2Evaluation Summary................................................................................................................................3 3Contents....................................................................................................................................................4 4General Information.................................................................................................................................5 4.1Details of E.U.T.................................................................................................................................5 4.2Evaluating Location...........................................................................................................................5 4.3Facility...............................................................................................................................................6 4.4Deviation from Standards..................................................................................................................6 4.5Abnormalities from Standard Conditions...........................................................................................6 5Technical Requirements Specification..................................................................................................7 5.1General Description of Applied Standards........................................................................................7 5.2RF Exposure Evaluation....................................................................................................................7 5.2.1Limit & Test Method......................................................................................................................7 5.2.2Conclusion....................................................................................................................................8 6EUT Constructional Details (EUT Photos).............................................................................................9 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240800100603 Page: 5 of 9 4General Information 4.1Details of E.U.T. Power supply:AC 120V 60Hz Cable(s):AC mains, 3 wires, 2.0m, unshielded. RF character:Refer to report GZCR240800100602 for BLE detail. Refer to report GZCR240800100603 for BT Classic detail. Remark: The information in this section is provided by the applicant or manufacturer, SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. 4.2Evaluating Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou Branch EMC Laboratory, No.198, Kezhu Road, Science City, Economic & Technological Development Area, Guangzhou, Guangdong, China 510663 Tel: +86 20 82155555 No tests were sub-contracted. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240800100603 Page: 6 of 9 4.3Facility The facility is recognized, certified, or accredited by the following organizations: ● ACMA SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory can also perform testing for the Australian/New Zealand Regulatory Compliance Mark (RCM). ● SGS UK(Certificate No.: 32), SGS-TUV SAARLAND and SGS-FIMKO Have approved SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory as a supplier of EMC TESTING SERVICES and SAFETY TESTING SERVICES. ● FCC Recognized Accredited Test Firm(Registration No.: 486818) SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory has been accredited and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Designation Number: CN5016, Test Firm Registration Number: 486818. ● ISED (Registration No.: 4620B, CAB identifier: CN0052) SGS-CSTC Standards Technical Services Co.…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240800100602 Page: 1 of 89 FCC ID: 2AWD4-ECHL-7747 Ricky Liu Manager TEST REPORT Application No.: GZCR2408001006HS Applicant: Echelon Fitness Multimedia, LLC Address of Applicant: 605 Chestnut Street, Suite 700, Chattanooga, TN 37450 Manufacturer: Echelon Fitness Multimedia, LLC Address of Manufacturer: 605 Chestnut Street, Suite 700, Chattanooga, TN 37450 Factory: Oma Fitness Equipment Co., Ltd Address of Factory: 93 Tai An Road South, Yang'e Village, Lunjiao Town, Shunde, Foshan, 528000, Guangdong, China Product Name: Motorized Treadmill, Stride-50-RCX Model No.: STRIDE-RCX Trade Mark: Echelon Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2024-06-06 Date of Test: 2024-06-18 to 2024-08-06 Date of Issue: 2024-09-19 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240800100602 Page: 2 of 89 Revision Record Version Report No. Date Remark 01 GZCR240800100602 2024-09-19 Original Authorized for issue by: Luke Lin/Project Engineer Vico Cui/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240800100602 Page: 3 of 89 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence N/A 47 CFR Part 15, Subpart C 15.247(a)(1),(g),(h) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Conducted Emissions at AC Power Line (150kHz-30MHz) 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.2 47 CFR Part 15, Subpart C 15.207 Pass Radiated Emissions which fall in the restricted bands ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Conducted Peak Output Power ANSI C63.10 (2013) Section 7.8.5 47 CFR Part 15, Subpart C 15.247(b)(1) Pass 20dB Bandwidth ANSI C63.10 (2013) Section 7.8.7 47 CFR Part 15, Subpart C 15.247(a)(1) Pass Carrier Frequencies Separation ANSI C63.10 (2013) Section 7.8.2 47 CFR Part 15, Subpart C 15.247a(1) Pass Hopping Channel Number ANSI C63.10 (2013) Section 7.8.3 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Dwell Time ANSI C63.10 (2013) Section 7.8.4 47 CFR Part 15, Subpart C 15.247a(1)(iii) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 7.8.6 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 7.8.8 47 CFR Part 15, Subpart C 15.247(d) Pass Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240800100602 Page: 4 of 89 3 Contents Page 1 Cover Page ........................................................................................................................................... 1 2 Test Summary ....................................................................................................................................... 3 3 Contents ............................................................................................................................................... 4 4 General Information.............................................................................................................................. 6 4.1 Details of E.U.T. ............................................................................................................................. 6 4.2 Description of Support Units ........................................................................................................... 6 4.3 Measurement Uncertainty .............................................................................................................. 7 4.4 Test Location ................................................................................................................................. 7 4.5 Test Facility .................................................................................................................................... 8 4.6 Deviation from Standards ............................................................................................................... 8 4.7 Abnormalities from Standard Conditions ......................................................................................... 8 5 Equipment List ..................................................................................................................................... 9 6 Radio Spectrum Technical Requirement ........................................................................................... 12 6.1 Antenna Requirement .................................................................................................................. 12 6.1.1 Test Requirement: ................................................................................................................... 12 6.1.2 Conclusion ............................................................................................................................... 12 6.2 Other requirements Frequency Hopping Spread Spectrum System Hopping Sequence ................ 13 6.2.1 Test Requirement: ................................................................................................................... 13 6.2.2 Conclusion .........................................................................…

Text truncated - open the document above for the full version.

Inverted F Antenna Specification Summary ITEMANT SPEC Model Name 2.4G ANT HorizontalVertical 2400MHz 2400MHz2500MHz2400MHz2400MHz 2500MHz Center Frequency -1.26 -0.76 -0.58 -5.25 -2.46 -1.86 MAX. Gain -0.58dB PolarizationHorizontal and Vertical Azimuth Beam Pattern Omni-directional Impedance50 Ohm Antenna Length 38.20mm Manufacture Echelon Fitness Multimedia, LLC 605 Chestnut Street, Suite 700, Chattanooga, TN 37450 Antenna Photo & Length (mm) Horizontal: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -40 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -1.26174 -30.0801 -7.18716 2450 -0.765802 -36.5604 -7.48023 2500 -0.585582 -22.0315 -6.59127 Vertical: 2400 MHz 2450 MHz 2500 MHz Power (dBm) Max: 0 Min: -30 Scale: 5/div Gain(dB) Frequency (MHz) Max Min Avg 2400 -5.2537 -22.1424 -12.4294 2450 -2.4652 -24.5837 -10.4702 2500 -1.86120 -29.5214 -9.20432 ANT Test Labs：Attestation of Global Compliance Co., Ltd.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-04 Rev 1.1 Page: 1 of 4 Appendix Test Setup Photo for GZCR240800100601 & GZCR240800100602 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-04 Rev 1.1 Page: 2 of 4 Test Setup Photo Conducted Emissions at AC Power Line (150kHz-30MHz) Radiated Emissions which fall in the restricted bands & Radiated Spurious Emissions Above 1GHz There is a holder to keep the RF antenna at the high 1.5 m above the floor. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-04 Rev 1.1 Page: 3 of 4 Radiated Spurious Emissions Below 1GHz SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-04 Rev 1.1 Page: 4 of 4 - End of the Appendix -