2AWMDA712RFID Smart Reader

α712 RFID UHF Reader User Guide Ver. 0.1 Copyright 2020. Aplusetechnology Co.,Ltd. All rights reserved. Apulsetech is the manufacturer of Apulsetech RFID handheld computers. This document and related software in this device are protected by international copyright laws. Any part of this document may not be reproduced, removed or used in any form by any means, without permission in writing from Apulsetech. The contents in this manual is subject to change without prior notice. Apulsetech and α712 are registered trademarks of Apulsetechnology Co.,Ltd., all other trademarks and copyrights are property of their respective owners. The software is provided for user understanding how to use the device and application development. All software, including firmware, is on a licensed basis. No right to copy a licensed program in whole or in part is granted, to other device except as permitted under copyright law. C-1211, 60, Haan-ro, Gwangmyeong-si, Gyeonggi-do, Republic of Korea http://www.apulsetech.com Change Date Description Ver.0.1 2020/10/31 Draft Table of Contents Copyright Revision History 1. About this guide ............................................................................................... 6 1.1 Introduction ........................................................................................................................... 6 1.2 Configuration ......................................................................................................................... 6 1.3 Related document and Software ........................................................................................... 6 1.4 Service information ............................................................................................................... 6 1.5 Safety information ................................................................................................................. 7 1.6 RF exposure precautions ....................................................................................................... 8 2. Brief Description of α712 ................................................................................... 9 2.1 Packing Contents ................................................................................................................... 9 2.2 α712 Review ........................................................................................................................... 9 2.2.1 Top side .......................................................................................................................... 9 2.2.2 Bottom side .................................................................................................................... 9 2.2.3 Front side ...................................................................................................................... 10 2.2.4 Back view ..................................................................................................................... 10 3. Getting Started ............................................................................................... 11 3.1 Installing and Replacing the Battery ................................................................................... 11 3.2 Charging the Battery ............................................................................................................ 11 3.2.1 When charging α712 and Mobile phone at the same time with DC Adapter .............. 11 3.3 Switching α712 on and off ................................................................................................... 11 3.4 Reset ..................................................................................................................................... 12 4. Android Connections ....................................................................................... 13 4.1 Compatible Product Models ................................................................................................ 13 4.2 Demo Apps ........................................................................................................................... 13 4.3 Connection ........................................................................................................................... 13 4.3.1 Setup ............................................................................................................................ 13 4.3.2 Make a Connection....................................................................................................... 13 5. Windows Connections ...................................................................................... 15 5.1 Compatible Product Models ................................................................................................ 15 5.2 Connection ........................................................................................................................... 15 5.2.1 Setup ............................................................................................................................ 15 5.2.2 Make a Connection....................................................................................................... 15 6. Follow Demo APK ............................................................................................ 18 6.1 UHF Reading ......................................................................................................................... 18 6.2 Barcode Scanning ................................................................................................................ 18 7. OS & Firmware Update ..................................................................................... 19 7.1 OS Update ............................................................................................................................ 19 7.2 RFID F/W Update .................................................................................................................. 19 8. Specifica…

Text truncated - open the document above for the full version.

Apulse Technology Co., Ltd. Add: C-1211, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi-do 14322, Republic of Korea April 22, 2021 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 In re : Apulse Technology Co., Ltd. FCC Application for FCC ID : 2AWMDA712 To whom it may concern: We, the undersigned, hereby attest to the fact that we will apply the Supplier’s Declaration of Conformity procedure to the class A computer peripheral portion of this composite filing. Regards, Sincerely, CFO / Robin Jang Apulse Technology Co., Ltd.

Apulse Technology Co., Ltd. Add: C-1211, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi-do 14322, Republic of Korea April 22, 2021 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 LETTER OF AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize LTA Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization for FCC ID: 2AWMDA712 including signing of all documents relating to these matters. Any and all acts carried out by LTA Co., Ltd., on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Apulse Technology Co., Ltd. LTA Co.,LTD. (Contact Person) Contact name: Ja-Beom Koo Position: Manager Phone:(82)31-323-6008 E- mail: [email protected] Sincerely, CFO / Robin Jang Apulse Technology Co., Ltd.

Apulse Technology Co., Ltd. Add: C-1211, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi-do 14322, Republic of Korea April 22, 2021 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 In re : Apulse Technology Co., Ltd. FCC ID : 2AWMDA712 Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules (CFR 47), Apulse Technology Co., Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality for 180 days after the grant as outlined in Public Notice DA 04-1705. This provision will give Apulse Technology Co., Ltd. temporary confidentiality of commercially sensitive information prior to product release. The requested Confidential and Temporary Confidential exhibits are listed as follows: Exhibit Type File Name CONFIDENTIAL Schematics CONF APPENDIX 2AWMDA712 SCH DIA.pdf Parts list CONF APPENDIX 2AWMDA712 PL.pdf Block diagram CONF APPENDIX 2AWMDA712 BLK DIA.pdf Operational description CONF APPENDIX 2AWMDA712 OpDes.pdf SHORT-TERM CONFIDENTIAL External Photos SHORT-TERM CONF 2AWMDA712EXT Photo.pdf Internal Photos SHORT-TERM CONF 2AWMDA712 INT Photo.pdf Te s t-Setup Photos SHORT-TERM CONF 2AWMDA712 Test Photo.pdf User’s Manual SHORT-TERM CONF 2AWMDA712 Manual.pdf The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Sincerely, CFO / Robin Jang Apulse Technology Co., Ltd.

April 22, 2021 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Cover Letter for Reused Test Teport FCC ID : 2AWMDA712 To Whom It May Concern: We, Apulse Technology Co., Ltd. hereby declare our product (RFID Reader) Model Number : a712 (FCC ID : 2AWMDA712) will reuse test reports of product (RFID Module) Model Number : IDRO900MI (FCC ID : XVY-IDRO900MI) as difference declaration as follow ; 1. Our product integrated RFID Module (FCC ID : XVY-IDRO900MI), so conducted test data re-used; 2. Radiation emission re-tested and reported in Report (Number : LR500112104N) ; 3. RF exposure no need to evaluated as the same intended condition ; 4. RFID Module is identical and in the same configuration as in the original test. The output power has been tested and verified in test report. We reuse test reports information as follows: Test Report Description Test Report Number RFID Module Test Report DRTFCC1510-0211 Should you have any qusetions or comments regarding this matter, please have any best attention. Sincerely, CFO / Robin Jang Apulse Technology Co., Ltd. Apulse Technology Co., Ltd. Add: C-1211, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi-do 14322, Republic of Korea

FCC ID: 2AWMDA712 Front Rear Copyright ○ c 2020, LTA Co., Ltd .Page 1 of 5 FCC ID: 2AWMDA712 To p Bottom Copyright ○ c 2020, LTA Co., Ltd .Page 2 of 5 FCC ID: 2AWMDA712 Left Right Copyright ○ c 2020, LTA Co., Ltd .Page 3 of 5 FCC ID: 2AWMDA712 ANTENNA(2.4 GHz) Copyright ○ c 2020, LTA Co., Ltd .Page 4 of 5 FCC ID: 2AWMDA712 Label Position Copyright ○ c 2020, LTA Co., Ltd .Page 5 of 5

Copyright ○ c 2021, LTA Co., Ltd. Page 1 of 9 EUT and Test Setup Photographs EUT Front view EUT Rear view Copyright ○ c 2021, LTA Co., Ltd. Page 2 of 9 EUT Top view EUT Bottom view Copyright ○ c 2021, LTA Co., Ltd. Page 3 of 9 EUT Right view EUT Left view Copyright ○ c 2021, LTA Co., Ltd. Page 4 of 9 Front of Device 0 mm from Phantom Top view Front of Device 0 mm from Phantom Side view Copyright ○ c 2021, LTA Co., Ltd. Page 5 of 9 Rear of Device 0 mm from Phantom Top view Rear of Device 0 mm from Phantom Side view Copyright ○ c 2021, LTA Co., Ltd. Page 6 of 9 Top of Device 0 mm from Phantom Top view Top of Device 0 mm from Phantom Side view Copyright ○ c 2021, LTA Co., Ltd. Page 7 of 9 Bottom of Device 0 mm from Phantom Top view Bottom of Device 0 mm from Phantom Side view Copyright ○ c 2021, LTA Co., Ltd. Page 8 of 9 Right of Device 0 mm from Phantom Top view Right of Device 0 mm from Phantom Side view Copyright ○ c 2021, LTA Co., Ltd. Page 9 of 9 Left of Device 0 mm from Phantom Top view Left of Device 0 mm from Phantom Side view

FCC ID: 2AWMDA712 SAMPLE LABEL & LOCATION EUT Bottom position Apulse Technology Co., Ltd. Model : a712 Rated Voltage : 3.7 V FCC ID : 2AWMDA712 Contain Module : XVY-IDRO900MI Made in Korea Copyright Ⓒ 2021, LTA Co., Ltd.

FCC ID: 2AWMDA712 MainBoard–Front MainBoard–Rear 2.4GHz Module Copyright ○ c 2020, LTA Co., Ltd. Page 1 of 4 FCC ID: 2AWMDA712 RFID Module Front RFID Module Rear Copyright ○ c 2020, LTA Co., Ltd. Page 2 of 4 FCC ID: 2AWMDA712 Antenna(UHF RFID) Copyright ○ c 2020, LTA Co., Ltd. Page 3 of 4 FCC ID: 2AWMDA712 Internal Copyright ○ c 2020, LTA Co., Ltd. Page 4 of 4

Ref. No.: LR500112102C Copyright ○ c 2021, LTA Co., Ltd. Page 1 of 57 243 Jubug-Ri,Yangji-Myeon, Yongin-Si, Gyeonggi-Do, Korea 449-822 Tel: +82-31-323-6008 Fax: +82-31-323-6010 http://www.ltalab.com SAR TEST REPORT Equipment Under Test Model Name Trade Mark Applicant Address of Applicant FCC ID Date of Receipt Date of Test(s) Date of Issue Max.SAR(1g) Standards: KDB Publication 447498 IEEE 1528, 2013 ANSI/IEEE C95.1, C95.3 In the configuration tested, the EUT complied with the standards specified above. Remarks: This report details the results of the testing carried out on one sample, the results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distribute in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of LTA Co., Ltd. Or testing done by LTA Co.,Ltd. In connection with distribution or use of the product described in this report must be approved by LTA Co.,Ltd. In writing. Tested by ;: Seon-Jong Park 2020-11-25 Approved by : Ja-Beom Koo 2020-11-25 : RFID : a712 : Apulse Technology Co.,Ltd : Apulse Technology Co.,Ltd : A-1403, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi-do, Korea : 2AWMDA712 : 2020-11-03 : 2020-11-03 ~ 2020-11-24 : 2020-11-25 : 0.103W/kg Ref. No.: LR500112102C Copyright ○ c 2021, LTA Co., Ltd. Page 2 of 57 Contents 1. EXECUTIVE SUMMARY & EUT INFORMATION ................................................ 2. INTRODUCTION ................................................................................................... 3. SAR MEASUREMENT SETUP ............................................................................. 4. ANSI/IEEE C95.1-2005 RF EXPOSURE LIMIT .................................................... 5. SYSTEM AND LIQUID VALIDATION ................................................................... 6. TYPE A MEASUREMENT UNCERTAINTY ......................................................... 7. OUTPUT POWER VERIFICATION ....................................................................... 8. SAR TEST RESULTS ........................................................................................... ANNEX A. TEST INSTRUMENT ........................................................................... ANNEX B. Simulated tissue electrostatic measurement results........................... ANNEX C. CALIBRATION REPORTS ..................................................................... ANNEX D. MAXIMUM PERMISSIBLE EXPOSURE Prediction 3 4 5 18 19 23 25 25 34 35 36 57 Ref. No.: LR500112102C Copyright ○ c 2021, LTA Co., Ltd. Page 3 of 57 The purpose of this test programmed was to demonstrate compliance of the Intermec Technologies Corporation Model: 1005CP01 against the current Stipulated Standards. The Mobile Computer have demonstrated compliance with the C95.1 , IEEE 1528, KDB Publication 447498 , RSS-102 Issue 5and Safety Code 6. The test has demonstrated that this unit complies with stipulated standards. EUT information EUT Description RFID Smart Reader Model No. a712 Serial No. Identical prototype Mode of Operations RFID Body-Worn Accessory N/A TX Frequency Range 902.75 MHz ~ 927.25 MHz Conducted Max Power 30.19 dBm Battery Type DC 3.7 V Antenna Location Antenna TypeLinear Polarized Antenna Gain3.06 dBi Usage distanceIt is held in the hand and used and has an antenna at the front, so it has biased characteristics (no contact with the human body). 1. Executive Summary & EUT Information Ref. No.: LR500112102C Copyright ○ c 2021, LTA Co., Ltd. Page 4 of 57 Diagram Antenna Location Ref. No.: LR500112102C Copyright ○ c 2021, LTA Co., Ltd. Page 5 of 57 Introduction This measurement report shows compliance of the EUT with FCC KDB Publication 447498 & RSS 102 Issue 4.0. The test procedures, as described in ANSI C95.1 – 2005 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz [2], and ANSI C95.3 – 2002 Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields [3], were employed. SAR Definition Specific Absorption Rate is defined as the time derivative (rate) of the incremental energy (dW) absorbed by (dissipated in) an incremental mass (dm) contained in a volume element (dV) of a given density (ρ). SAR is expressed in units of watts per kilogram (W/kg). SAR can be related to the electric field at a point by where: σ = conductivity of the tissue (S/m) ρ = mass density of the tissue (kg/m3) E = rms electric field strength (V/m) 2. Introduction Ref. No.: LR500112102C Copyright ○ c 2021, LTA Co., Ltd. Page 6 of 57 Dosimetric Assessment System These measurements were performed with the automated near-field scanning system OPENSAR from SATIMO. The system is based on a high precision robot (working range: 850 mm), which positions the probes with a positional repeatability of better than ± 0.02 mm. Special E- and H-field probes have been developed for measurements close to material discontinuity, the sensors of which are directly loaded with a Schottky diode and connected via highly resistive lines to the data acquisition unit. The SAR measurements were conducted with dosimetric probe (manufactured by SATIMO), designed in the classical triangular configuration and optimized for dosimetric evaluation. The probe has been calibrated according to the procedure described in SAR standard with accuracy of better than ±10%. The spherical isotropy was evaluated with the procedure described in SAR starndard and found to be better than ±0.25 dB. The phantom used was the SAM Phantom as described in FCC supplement C, IEEE P1528 and CENELEC EN62209-1. Measurement System Diagram The OPENSAR system for performing compliance tests con…

Text truncated - open the document above for the full version.

Ref. No.: LR500112104M 243 Jubug-Ri,Yangji-Myeon, Yongin-Si, Gyeonggi-Do, Korea 17159 Tel: +82-31-323-6008 Fax: +82-31-323-6010 http://www.ltalab.com Dates of Tests: Dec 01 2020 ~ Apr 22, 202 1 Test Report S/N: LR500112104M Test Site : LTA CO., LTD. CERTIFICATION OF COMPLIANCE FCC ID. APPLICANT Equipment Class : Digital Transmission System (DTS) _LE,802.11 Manufacturing Description : RFID Smart Reader Manufacturer : Apulse Technology Co., Ltd. Model name : a712 Test Device Serial No.: : Identical prototype Rule Part(s) : FCC Part 15.247 Subpart C ; ANSI C63.10 - 2013 Frequency Range : BLE 2402 ~ 2480 MHz 802.11 b,g,n20 2412 ~ 2462 MHz Max. Output Power : Max 8.29 dBm - Conducted Data of issue : April 23, 2021 This test report is issued under the authority of: The test was supervised by: Ja- Beom Koo, Manager Eun -Hwan Jung, Test Engineer This test result only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the test laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. NVLAP LAB Code.: 200723-0 2AWMDA712 Apulse Technology Co., Ltd. Copyright ○ c 2019, LTA Co., Ltd. Page 1 of 50 Ref. No.: LR500112104M TABLE OF CONTENTS 1. GENERAL INFORMATION -------------------------------------------------------------------------- 2. INFORMATION ABOUT TEST ITEM ------------------------------------------------------------- 3. TEST REPORT ------------------------------------------------------------------------------------------ 3.1 SUMMARY OF TESTS ---------------------------------------------------------------------------- 3.2 TECHNICAL CHARACTERISTICS TEST ---------------------------------------------------- 3.2.1 6 dB BANDWIDTH -------------------------------------------------------------------------- 3.2.2 PEAK OUTPUT POWER -------------------------------------------------------------------- 3.2.3 POWER SPECTRAL DENSITY ------------------------------------------------------------ 3.2.4 BAND EDGE ---------------------------------------------------------------------------------- 3.2.5 CONDUCTED SPURIOUS EMISSIONS ------------------------------------------------- 3.2.6 RADIATED SPURIOUS EMISSIONS ---------------------------------------------------- APPENDIX APPENDIX TEST EQUIPMENT USED FOR TESTS -------------------------------------------- 3 4 5 5 6 6 12 18 24 29 34 50 Copyright ○ c 2019, LTA Co., Ltd. Page 2 of 50 Ref. No.: LR500112104M 1. General information 1-1 Test Performed Company name : LTA Co., Ltd. Address : 243, Jubug-ri,Yangji-Myeon,Youngin-Si, Kyunggi-Do, Korea. 17159 Web site : http://www.ltalab.com E- mail : [email protected] Telephone : +82 -31-323-6008 Facsimile +82 -31-323-6010 Quality control in the testing laboratory is implemented as per ISO/IEC 17025 which is the “General requirements for the competents of calibration and testing laboratory”. 1-2 Accredited agencies LTA Co., Ltd. is approved to perform EMC testing by the following agencies: Agency Country Accreditation No. Validity Reference NVLAP U.S.A 200723-0 2021-09-30 ECT accredited Lab. RRA KOREA KR0049 - EMC accredited Lab. FCC U.S.A 649054 2021-04-11 FCC CAB VCCI JAPAN C-4948, 2023-09-10 VCCI registration VCCI JAPAN T-2416, 2023-09-10 VCCI registration VCCI JAPAN R-4483(10 m), 2023-08-15 VCCI registration VCCI JAPAN G-847 2021-12-13 VCCI registration IC CANADA 5799A-1 2021-06-16 IC filing KOLAS KOREA NO.551 2021-08-20 KOLAS accredited Lab. Copyright ○ c 2019, LTA Co., Ltd. Page 3 of 50 Ref. No.: LR500112104M 2. Information about test item 2-1 Client & Manufacturer Client Company name : Apulse Technology Co., Ltd. Address : A- 1403, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi- do, Korea Tel / Fax : +82 -10-5526-0605 / +82-70-4222 -5686 Manufacturer Apulse Technology Co., Ltd. Address A- 1403, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi- do, Korea Tel / Fax +82 -10-5526-0605 / +82-70-4222-5686 2-2 Equipment Under Test (EUT) Model name : a712 Serial number : Identical prototype Date of receipt : Dec 01, 2020 EUT condition : Pre-production, not damaged Antenna type : FPCB Antenna (Max Gain : 0.07 dBi) Frequency Range : BLE 2402 ~ 2480 MHz 802.11 b,g,n20 2412 ~ 2462 MHz RF output power : Max 8.29 dBm – Conducted Type of Modulation : Pi/4 DQPSK, 8DPSK, OFDMA Power Source : DC 3.7 V 2-3 Tested frequency LOW MID HIGH Frequency (MHz) 802.11 b,g,n20 2412 2442 2462 Frequency (MHz) BLE 2402 2442 2480 2-4 Ancillary Equipment Equipment Model No. Serial No. Manufacturer Notebook - MS-1736 MSI Copyright ○ c 2019, LTA Co., Ltd. Page 4 of 50 Ref. No.: LR500112104M 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Test Condition Status (note 1) 15.247(a) 6 dB Bandwidth Conducted C 15.247(b) Transmitter Peak Output Power C 15.247(e) Transmitter Power Spectral Density C 15.247(d) Band Edge & Conducted Spurious emission C 15.209 Transmitter emission Radiated C 15.207 AC Conducted Emissions Conducted N/A 15.203 Antenna requirement - C N/A : This product is battery-enabled and excludes the test. The above equipment was tested by LTA Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.247 The test results of this report relate only to the tested sample identified in this report. The tests were performed according to the method of measurements prescribed in KDB No.558074.  Antenna Requirement Apulse Technology Co., Ltd. FCC ID: 2AWMDA712 unit complies with the requirement of §15.203. The antenna type is PCB Antenna Copyright ○ c 2019, LTA Co., Ltd. Page 5 of 50 Ref. No.: LR500112104M 3.2 Technical Characteristics Test 3.2.1 6 dB Bandwidth Procedure: The bandwidth at …

Text truncated - open the document above for the full version.

Ref. No.: LR500112104N 243 Jubug-Ri,Yangji-Myeon, Yongin-Si, Gyeonggi-Do, Korea 17159 Tel: +82-31-323-6008 Fax: +82-31-323-6010 http://www.ltalab.com Dates of Tests: Mar 02 ~ Apr 22, 2021 Test Report S/N: LR500112104N Test Site : LTA CO., LTD. CERTIFICATION OF COMPLIANCE FCC ID. APPLICANT Equipment Class : Digital Transmission System (DTS) Manufacturing Description : PDA Manufacturer : Apulse Technology Co., Ltd. Model name : a712 Module FCCID : XVYIDRO900MI Test Device Serial No.: : Identical prototype Rule Part(s) : FCC Part 15.247 Subpart C ; ANSI C63.10 - 2013 Frequency Range : 902.75 ~ 927.25 MHz Max. Output Power : Max 0.914 W - Conducted Data of issue : April 23, 2021 This test report is issued under the authority of: The test was supervised by: Ja-Beom Koo, Manager Eun-Hwan Jung, Test Engineer This test result only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the test laboratory. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. NVLAP LAB Code.: 200723-0 2AWMDA712 Apulse Technology Co., Ltd. Copyright ○ c 2021, LTA Co., Ltd. Page 1 of 12 Ref. No.: LR500112104N TABLE OF CONTENTS 1. GENERAL INFORMATION -------------------------------------------------------------------------- 2. INFORMATION ABOUT TEST ITEM ------------------------------------------------------------- 3. TEST REPORT ------------------------------------------------------------------------------------------ 3.1 SUMMARY OF TESTS ---------------------------------------------------------------------------- 3.2 TECHNICAL CHARACTERISTICS TEST ---------------------------------------------------- 3.2.2 Peak Output Power Measurement ------------------------------------------------------------------ 3.2.1 RADIATED SPURIOUS EMISSIONS------------------------------------------------------------ APPENDIX APPENDIX TEST EQUIPMENT USED FOR TESTS -------------------------------------------- 3 4 5 5 6 6 7 12 Copyright ○ c 2021, LTA Co., Ltd. Page 2 of 12 Ref. No.: LR500112104N 1. General information 1- 1 Test Performed Company name : LTA Co., Ltd. Address : 243, Jubug-ri,Yangji-Myeon,Youngin-Si, Kyunggi-Do, Korea. 17159 Web site : http://www.ltalab.com E-mail : [email protected] Telephone : +82-31-323-6008 Facsimile +82-31-323-6010 Quality control in the testing laboratory is implemented as per ISO/IEC 17025 which is the “General requirements for the competents of calibration and testing laboratory”. 1- 2 Accredited agencies LTA Co., Ltd. is approved to perform EMC testing by the following agencies: Agency Country Accreditation No. Validity Reference NVLAP U.S.A 200723-0 2021-09-30 ECT accredited Lab. RRA KOREA KR0049 - EMC accredited Lab. FCC U.S.A 649054 2021-04-11 FCC CAB VCCI JAPAN C-4948, 2023-09-10 VCCI registration VCCI JAPAN T-2416, 2023-09-1 0 VCCI registration VCCI JAPAN R-4483(10 m), 2023-08-1 5 VCCI registration VCCI JAPAN G-847 2021-12-13 VCCI registration IC CANADA 5799A-1 2021-06-16 IC filing KOLAS KOREA NO.551 2021-08-20 KOLAS accredited Lab. Copyright ○ c 2021, LTA Co., Ltd. Page 3 of 12 Ref. No.: LR500112104N 2. Information about test item 2-1 Client & Manufacturer Client Company name : Apulse Technology Co., Ltd. Address : A-1403, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi- do, Korea Tel / Fax : +82-10-5526-0605 / +82-70-4222-5686 Manufacturer Apulse Technology Co., Ltd. Address A-1403, Gwangmyeongtechnopark, 60, Haan-ro, Gwangmyeong-si, Gyeonggi- do, Korea Tel / Fax +82-10-5526-0605 / +82-70-4222-5686 2- 2 Equipment Under Test (EUT) Model name : a712 Serial number : Identical prototype Date of receipt : Dec 01, 2020 EUT condition : Pre-production, not damaged Antenna type : PCB Antenna (Max Gain : 3.056 dBi) Frequency Range : 902.75 ~ 927.25 MHz Type of Modulation : GFSK Power Source : DC 3.7 V 2- 3 Tested frequency LOW MID HIGH Frequency (MHz) 902.75 915.25 927.25 2-4 Ancillary Equipment Equipment Model No. Serial No. Manufacturer - - - - Copyright ○ c 2021, LTA Co., Ltd. Page 4 of 12 Ref. No.: LR500112104N 3. Test Report 3.1 Summary of tests FCC Part Section(s) Parameter Test Condition Status (note 1) 15.247(a) 6 dB Bandwidth Conducted N/A 1) 15.247(b) Transmitter Peak Output Power C 15.247(e) Transmitter Power Spectral Density N/A 1) 15.247(d) Band Edge & Conducted Spurious emission N/A 1) 15.209 Transmitter emission Radiated C 15.207 AC Conducted Emissions Conducted N/A 1) 15.203 Antenna requirement - C N/A 1) : The product replaces this test with a certificate using an authenticated module. The above equipment was tested by LTA Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10-2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.247 The test results of this report relate only to the tested sample identified in this report. The tests were performed according to the method of measurements prescribed in KDB No.558074.  Antenna Requirement Apulse Technology Co., Ltd. FCC ID: 2AWMDA712 unit complies with the requirement of §15.203. The antenna type is PCB Antenna Copyright ○ c 2021…

Text truncated - open the document above for the full version.