2AWV7029757739Bird Air

Get started. Placeholder TAIL LIGHT STOMP BRAKE LEVER NECK LOCKING SLEEVE CHARGING PORT HEADLIGHT HANDLEBAR KICKSTAND Assembly Materials x 4 SCREWS x 1 HANDLEBAR ASSEMBLY BIRD AIR VEHICLE (FOLDED) x 1 ALLEN WRENCH x 1 CHARGER AND PLUG Assembly LIFT THE NECK Lift the vertical tube (neck) from the top and move it to an upright position. 1 ROTATE THE NECK INTO PLACE Rotate the lever at the base of the neck up while holding the neck in place. The lever must be completely locked in the upright position. 2 SLIDE THE LOCKING SLEEVE DOWN Slide the locking sleeve down until it clicks into place with the lever. 3 CONNECT THE HANDLEBAR ASSEMBLY Take the handlebar assembly and connect its connector (green) to the Bird Air connector at the top of the neck. Align the connectors using the arrows as visual aids. Once arrows are aligned push them together to connect. 4 SLIDE THE HANDLEBARS INTO PLACE Slide the handlebar assembly down into the neck with the wires inside. The middle part of the handlebars should slope down toward the rear of the vehicle. Push the handle bar down, until it’s fully seated in the neck. 5 INSTALL THE (4) SCREWS Pick up the (4) screws and the Allen wrench. Then, find the (4) screw holes at the top of the neck, near the handlebar assembly. There are two holes each on opposite sides of the neck. Use the Allen wrench to install the (4) screws. Tighten the screws until they are snug and then rotate an additional ¼ turn. 6 Charging CONNECT THE POWER ADAPTER Once you’ve assembled your Bird Air, it’s time to charge. Use the included power supply and connect it to the charging port. 1 FINISH CHARGING When fully charged, a green light on the power supply indicates the charge is complete. Disconnect the power supply from the charging port before riding. 2 Do not attempt to charge if the charging port or power adaptor is wet. WARNING: Only use charger specified by the manufacturer. MANUFACTURER: DONGGUAN ANGDI TECHNOLOGY CO LTD, MODEL: BC266420200 WARNING: Ambient temperature must be 32-104°F (0-40°C)′′ during charging. The battery will not charge outside of these temperature limits. WARNING: Risk of Fire: Do not attempt to disassemble the charger. No user serviceable parts. WARNING: Riding POWER ON To turn the Bird Air on or off, hold down the Power button for at least 2 seconds at the bottom of the dash display (center console of the handlebar assembly). The vehicle will audibly “beep” when it is powered on or off. Additionally, the dash display will activate. 1 DOWNLOAD THE BIRD APP Download and install the Bird App on your smartphone to gain wireless access to the dash display controls. Follow the in-app instructions to pair with the vehicle. 2 2 secs TURN ON THE HEADLIGHT Press the power button once to turn the headlight on and off. 4 CHECK THE DASH DISPLAY The Bird Air uses a dash display screen to show the speed (miles per hour or kilometers per hour) and charge level. 3 The dash display shows the speed mode the Bird Air is in. There are 3 different speed modes: To switch between the three modes, double-tap the power button. Double-tapping will always cycle in order of Takeoff, Glide, and Fly speed. x 1x 1 TAKEOFF Max speed of 9 mph/15 km/h GLIDE Max speed of 12-12.5 mph/20 km/h, indicated by a yellow circle F LY Max speed of 16 mph/26 km/h, indicated by a red circle STARTING To start a ride, first, make sure to fold in the kickstand. Kick to start the Bird Air by having one foot on the vehicle and one foot on the ground. Push the vehicle with at least two kicks before boarding it to ride. Press the throttle (accelerator) down at the right handlebar to accelerate the scooter. 5 STOPPING Use the brake at the left handlebar to decelerate or stop the vehicle. Additionally, it is possible to use the stomp brake as a brake for the vehicle. 6 THROTTLE BRAKE STOMP BRAKE Folding SLIDE THE LOCKING SLEEVE UP Take hold of the locking sleeve and slide the sleeve up from the lever. 1 ROTATE THE LEVER DOWN While holding the locking sleeve in place atop the lever, rotate the lever down. 2 FOLD THE NECK DOWN Take hold of the neck and fold it down 90 degrees until the handlebar assembly is just above the stomp brake. 3 LOCK THE NECK INTO THE FENDER Push the neck down atop the stomp brake until the black tab at the base of the handlebar assembly meets with the stomp brake. Hold the stomp brake down, then push the neck further into the fender until the black tab locks into place. Let go of the stomp brake and neck. It is now possible to lift the scooter from the neck. 4 The Bird Air can be folded for convenience. Ensure the Bird Air is powered off before attempting to fold it. Unfolding RELEASE THE TAB Push down the stomp brake to free the tab at the base of the handlebar assembly. 1 SET THE NECK AND LEVER Lift the neck 90 degrees to the upright position on the vehicle. Push the lever at the base of the neck up. 2 SLIDE THE LOCKING SLEEVE DOWN Slide the locking sleeve down into the lever, making sure it clicks into place. The lever must be completely locked in the upright position. 3 Reverse the folding process to unfold the Bird Air. STOMP BRAKE WARNING: Failure to follow unfolding instructions could result in unintentional folding. Ensure that the lever is upright and the sleeve is locked in place. Battery Range Charging App Firmware Connectivity Splash Resistant Lights Braking Wheels Top Speed Hill Grade Weight Limit Storage Temperature Operating Temperature Input Voltage Charging Temperature 5.2 Ah (10S2P) Up to 15.5 miles Fast charge port iOS and Android Over-the-Air updates Bluetooth Chassis IP34 , Motor IP67 , Battery IP67 Front LED, automatic rear LED Throttle and foot 7.9′′ Semi-solid 16 mph 8% grade 220 lb (100 kg) 14 –104°F (-10-40°C) 14 –104°F (-10-40°C) Length x Width x Height Weight 38.6" X 18.1" X 45.1" (981 mm X 460 mm X 1145 mm) 25.35 lb (11.5 kg) 100-240AC, Output Voltage = 42VDC, Output Current: 2.0 Amps, Charger Manufacturer: DONGGUAN ANGDI TECHNOLOGY CO LTD, Model: BC266420200 (O…

Text truncated - open the document above for the full version.

Date: 07282020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AWV7029757739 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Keny Xu in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Bird Rides Inc. This authorization is valid until further written notice from the applicant. Sincerely, Print Name: Brian Buccella Title: VP, Vehicle Strategy Signature: On behalf of Company: Bird Rides Inc. Telephone: 866-205-2442 E-mail: [email protected] BIRD RIDES INC., 406 BROADWAY #369, SANTA MONICA, CA 90401 DocuSign Envelope ID: 5B4AD417-767E-4A59-BF4B-8E3922841A48

To: Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: Bird Rides Inc. 406 Broadway #369 Santa Monica, CA 90401 Regarding: Confidentiality Request regarding application for FCC ID: 2AWV7029757739 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 90 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Brian Buccella Title: VP, Vehicle Strategy Signature: On behalf of Company: Bird Rides Inc. Telephone: 866-205-2442 E-mail: [email protected] BIRD RIDES INC., 406 BROADWAY #369, SANTA MONICA, CA 90401 DocuSign Envelope ID: 5B4AD417-767E-4A59-BF4B-8E3922841A48

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1)labeling the equipment with the exact FCC ID as specified in this application, (2)compliance statement labeling pursuant to the applicable rules, (3)compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1)the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2)the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3)the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Legal Business Name Bird Rides Inc. Address 406 Broadway #369, Santa Monica, CA 90401 Grantee Code 2AWV7 FCC ID 2AWV7029757739 Authorized Contact Name Brian Buccella Contact [email protected] Contact Phone 866-205-2442 Applicant Signature: Date: Print Name:Brian Buccella Title: VP, Vehicle Strategy Applicant Declara-on Rev:0.0 DocuSign Envelope ID: 5B4AD417-767E-4A59-BF4B-8E3922841A48 7/28/2020

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 5 External Photos for SZEM2007006607CR FCC ID: 2AWV7029757739 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 5 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 5

(Label location: bottom of the vehicle)

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 10 Internal Photos for SZEM2007006607CR FCC ID: 2AWV7029757739 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 10 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 10 Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 8 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 9 of 10 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 10 of 10

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660703 Page: 1 of 6 Keny Xu EMC Laboratory Manager 1 Cover page SAR Evaluation Report Application No.: SZEM2007006607CR Applicant: Bird Rides Inc. Address of Applicant: 406 Broadway Suite 369 Santa Monica, CA 90401 USA Manufacturer: Bird Rides Inc. Address of Manufacturer: 406 Broadway Suite 369 Santa Monica, CA 90401 USA Factory: HL Corp (Shenzhen) Address of Factory: The 3rd Industrial Park, Bitou Village, SongGang Town, Bao'an District, Shenzhen, Guangdong Province Equipment Under Test (EUT): EUT Name: Bird Air Model No.: VA00020, VA00021   Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: Bird FCC ID: 2AWV7029757739 Standards: 47 CFR Part 1.1307 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2020-07-17 Date of Test: 2020-07-21 to 2020-07-27 Date of Issue: 2020-08-03 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660703 Page: 2 of 6 2 Version Revision Record Version Chapter Date Modifier Remark 01 2020-08-03 Original Authorized for issue by: Powell Bao /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660703 Page: 3 of 6 3 Contents Page 1 COVER PAGE .............................................................................................................................................. 1 2 VERSION ...................................................................................................................................................... 2 3 CONTENTS .................................................................................................................................................. 3 4 GENERAL INFORMATION .......................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF EUT ............................................................................................................. 4 4.2 TEST LOCATION ...................................................................................................................................... 5 4.3 TEST FACILITY ........................................................................................................................................ 5 4.4 DEVIATION FROM STANDARDS ................................................................................................................. 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 5 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 5 5 SAR EVALUATION ...................................................................................................................................... 6 5.1 RF EXPOSURE COMPLIANCE REQUIREMENT ............................................................................................ 6 5.1.1 Standard Requirement ..................................................................................................................... 6 5.1.2 Limits ................................................................................................................................................ 6 5.1.3 EUT RF Exposure ............................................................................................................................ 6 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660703 Page: 4 of 6 4 General Information 4.1 General Description of EUT Power Supply: operated by DC36V rechargeable battery and can be charged by adapter with Model: BC266420200 Input: AC100-240V, 1.8A(Max.), 50/60Hz Output: DC42V, 2.0A Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V4.2 LE Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: PCB Antenna Antenna Gain: 3dBi Declaration of EUT Family Grouping: Model No.: VA00020, VA00021 Only the model VA00020 was tested, since according to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model number and colours. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660703 Page: 5 of 6 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC S…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660702 Page: 1 of 51 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM2007006607CR Applicant: Bird Rides Inc. Address of Applicant: 406 Broadway Suite 369 Santa Monica, CA 90401 USA Manufacturer: Bird Rides Inc. Address of Manufacturer: 406 Broadway Suite 369 Santa Monica, CA 90401 USA Factory: HL Corp (Shenzhen) Address of Factory: The 3rd Industrial Park, Bitou Village, SongGang Town, Bao'an District, Shenzhen, Guangdong Province Equipment Under Test (EUT): EUT Name: Bird Air Model No.: VA00020, VA00021   Please refer to section 2 of this report which indicates which model was actually tested and which were electrically identical. Trade Mark: Bird FCC ID: 2AWV7029757739 Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2020-07-17 Date of Test: 2020-07-23 to 2020-07-27 Date of Issue: 2020-08-03 Test Result: Pass * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660702 Page: 2 of 51 Revision Record Version Chapter Date Modifier Remark 01 2020-08-03 Original Authorized for issue by: Powell Bao /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660702 Page: 3 of 51 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Minimum 6dB Bandwidth 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Conducted Peak Output Power 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Power Spectrum Density 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 6.4,6.5,6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Declaration of EUT Family Grouping: Model No.: VA00020, VA00021 Only the model VA00020 was tested, since according to the declaration from the applicant, the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model number and colours. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200700660702 Page: 4 of 51 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 6 4.1 DETAILS OF E.U.T. ............................................................................................................................... 6 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 6 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 6 4.4 TEST LOCATION .................................................................................................................................... 7 4.5 TEST FACILITY ...................................................................................................................................... 7 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 7 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 7 5 EQUIPMENT LIST ...................................................................................................................................... 8 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 12 6.1 ANTENNA REQUIREMENT .................................................................................................................... 12 6.1.1 Test Requirement: ....................................................................................................................... 12 6.1.2 Conclusion ................................................................................................................................... 12 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 13 7.1 MINIMUM 6DB BANDWIDTH .................................................................................................................. 13 7.1.1 E.U.T. Operation .......................................................................................................................... 13 7.1.2 Test Setup Diagram .........................................................................................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZEM2007006607CR FCC ID: 2AWV7029757739 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs 1.1 Radiated Emissions which fall in the restricted bands Test Setup 1.2 Radiated spurious Emissions Test Setup SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3