2AXPS-WPC003-1Wireless Charger

Wireless Charger- WPC003-1 This wireless charger can charge your Qi-enabled smartphone. Just simply place your smartphone on the rubber mat above the wireless charger. The wireless charger supports up to 5W power delivery. NOTE:The wireless charger may not work if your phone case is metal. Take the phone out of the case and place the phone on the charger. FCC Certification FCC ID:2AXPS-WPC003-1 The devices listed above comply with Part 15 of the FCC rules and Industry Canada's license- exempt RSS Standard(s) and EU Directive 2014/53/EU. Operation is subject to the following two conditions: 1.This device may not cause harmful interference; and 2.This device must accept any interference received, including interference that may cause undesired operation. Note: Radiation Exposure Statement The product comply with the FCC/IC RF Exposure for Low Power Consumer Wireless Power Transfer. RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure that compliance was demonstrated at 20cm and greater separation from the user body or set the device to lower output power if such function is available. Canada CAN ICES-3 (B)/NMB-3(B) Caution: This equipment and its antennas must not be co-located or operated withanother antenna or transmitter. Caution: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Radiation Exposure Statement: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Frequency band in which the radio equipment operates: 110~ 115kHz Maximum power transmitted: < 0.01mW Model name: Wireless Charger Manufacturer: BCS Automotive Interface Solutions（Suzhou）Co., Ltd. Model Number: WPC003-1 Max. Output: 5W Input: 13.5V 1A Operating Temperature:-40°C~85°C Storage Temperature: -40°C~105°C

Annex No.: BL-EC2090870-AW 1 / 3 ANNEX C UT EXTERNAL PHOTOS FRONT VIEW OF EUT REAR VIEW OF EUT Annex No.: BL-EC2090870-AW 2 / 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT Annex No.: BL-EC2090870-AW 3 / 3 TOP VIEW OF EUT BOTTOM VIEW OF EUT

1 /3 ANNEXDEUTINTERNALPHOTOS EUTUNCOVERVIEW EUTUNCOVERVIEW Annex No.: BL-EC2090890-AI 2 /3 MAINBOARDTOPVIEW MAINBOARDREARVIEW Annex No.: BL-EC2090890-AI 3 /3 MAINBOARDTOPVIEW MAINBOARDREARVIEW Coil RF CHIP Annex No.: BL-EC2090890-AI

Report No.: BL-EC2090870-701 2 / 13 Revision History Version Issue Date Revisions Content Rev. 01 Oct. 19, 2020 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION .................................................................................................................... 4 1.1 Identification of the Testing Laboratory ..................................................................................... 4 1.2 Identification of the Responsible Testing Location .................................................................... 4 1.3 Test Environment Condition ..................................................................................................... 4 1.4 Announce ................................................................................................................................. 5 2 PRODUCT INFORMATION ................................................................................................................... 6 2.1 Applicant Information ................................................................................................................ 6 2.2 Manufacturer Information .......................................................................................................... 6 2.3 Factory Information ................................................................................................................... 6 2.4 General Description for Equipment under Test (EUT) ............................................................... 6 2.5 Ancillary Equipment .................................................................................................................. 6 2.6 Technical Information ............................................................................................................... 7 3 STANDARD INFORMATION ................................................................................................................. 8 3.1 Test Standard ........................................................................................................................... 8 3.2 Radiofrequency Radiation Exposure Limit ................................................................................ 8 3.3 Measurement Uncertainly ......................................................................................................... 9 4 TEST SETUP ...................................................................................................................................... 10 4.1 Test Setup Photo .................................................................................................................... 10 4.2 Measurement procedure ......................................................................................................... 10 4.3 Mobile Condition ..................................................................................................................... 10 4.4 Equipment Approval Considerations item 5.2 of KDB 680106 D01 v03. ................................. 11 4.5 Test Equipment ...................................................................................................................... 11 4.6 Test Configuration .................................................................................................................. 12 5 TEST RESULT .................................................................................................................................... 12 5.1 H-field ..................................................................................................................................... 12 5.2 E-field ..................................................................................................................................... 12 6 Test Conclusion ................................................................................................................................... 13 Report No.: BL-EC2090870-701 3 / 13 6.1 H-field ..................................................................................................................................... 13 6.2 E-field ..................................................................................................................................... 13 Report No.: BL-EC2090870-701 4 / 13 1 GENERAL INFORMATION 1.1 Identification of the Testing Laboratory Company Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China. Phone Number +86 755 6685 0100 Fax Number +86 755 6182 4271 1.2 Identification of the Responsible Testing Location Test Location Shenzhen BALUN Technology Co., Ltd. Address Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China. Accreditation Certificate The laboratory has been listed by Industry Canada to perform electromagnetic emission measurements. The recognition numbers of test site are 11524A-1. The laboratory has been listed by US Federal Communications Commission to perform electromagnetic emission measurements. The recognition numbers of test site are 832625. The laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L6791. Description All measurement facilities used to collect the measurement data are located at Block B, FL 1, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 518055 1.3 Test Environment Condition Ambient Temperature 21 to 23 °C Ambient Relative Humidity 40 to 50% Ambient Pressure 100 to 102 KPa Report No.: BL-EC2090870-701 5 / 13 1.4 Announce (1) The test report reference to the report template version v1.2. (2) The test report is invalid if not marked with the signatures of the persons responsible for preparing and approving the test report. (3) The test report is inval…

Text truncated - open the document above for the full version.

Annex No.: BL-EC2090870-AS 1 1 / 3 TEST SETUP PHOTOS E-field Test Setup Photo Positon A Load (15cm) E-field Test Setup Photo Positon B Load (15cm) Annex No.: BL-EC2090870-AS 1 2 / 3 E-field Test Setup Photo Positon C Load (15cm) E-field Test Setup Photo Positon D Load (15cm) Annex No.: BL-EC2090870-AS 1 3 / 3 E-field Test Setup Photo Positon E Load (20cm) Artificial Load

Report No.: BL-EC2090870-402 2 / 22 Revision History Version Issue Date Revisions Rev. 01 Oct. 19, 2020 Initial Issue TABLE OF CONTENTS 1 GENERAL INFORMATION .................................................................................................................... 4 1.1 Identification of the Testing Laboratory ............................................................................................ 4 1.2 Identification of the Responsible Testing Location ........................................................................... 4 1.3 Laboratory Condition ....................................................................................................................... 4 1.4 Announce ........................................................................................................................................ 5 2 PRODUCT INFORMATION ................................................................................................................... 6 2.1 Applicant Information ....................................................................................................................... 6 2.2 Manufacturer Information ................................................................................................................ 6 2.3 Factory Information ......................................................................................................................... 6 2.4 General Description for Equipment under Test (EUT) ..................................................................... 6 2.5 Ancillary Equipment ......................................................................................................................... 7 2.6 Technical Information ...................................................................................................................... 7 3 SUMMARY OF TEST RESULTS ........................................................................................................... 8 3.1 Test Standards ................................................................................................................................ 8 3.2 Verdict ............................................................................................................................................. 8 3.3 Test Uncertainty .............................................................................................................................. 8 4 GENERAL TEST CONFIGURATIONS .................................................................................................. 9 4.1 Test Environments .......................................................................................................................... 9 4.2 Test Equipment List ......................................................................................................................... 9 4.3 Test Setups ................................................................................................................................... 10 5 TEST ITEMS ....................................................................................................................................... 12 5.1 Emission Tests .............................................................................................................................. 12 ANNEX A TEST RESULTS ..................................................................................................................... 16 A.1 Radiated Emission ........................................................................................................................ 16 A.2 Conducted Emission ..................................................................................................................... 19 A.3 20 dB Bandwidth ........................................................................................................................... 21 Report No.: BL-EC2090870-402 3 / 22 ANNEX B TEST SETUP PHOTOS ......................................................................................................... 22 ANNEX C EUT EXTERNAL PHOTOS .................................................................................................... 22 ANNEX D EUT INTERNAL PHOTOS ...................................................................................................... 22 Report No.: BL-EC2090870-402 4 / 22 1 GENERAL INFORMATION 1.1 Identification of the Testing Laboratory Company Name Shenzhen BALUN Technology Co., Ltd. Address Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Phone Number +86 755 6685 0100 1.2 Identification of the Responsible Testing Location Test Location Shenzhen BALUN Technology Co., Ltd. Address Block B, 1st FL, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China Accreditation Certificate The laboratory has been listed by Industry Canada to perform electromagnetic emission measurements. The recognition numbers of test site are 11524A-1. The laboratory is a testing organization accredited by FCC as a accredited testing laboratory. The designation number is CN1196. The laboratory is a testing organization accredited by American Association for Laboratory Accreditation(A2LA) according to ISO/IEC 17025.The accreditation certificate is 4344.01. The laboratory is a testing organization accredited by China National Accreditation Service for Conformity Assessment (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L6791. Description All measurement facilities used to collect the measurement data are located at Block B, FL 1, Baisha Science and Technology Park, Shahe Xi Road, Nanshan District, Shenzhen, Guangdong Province, P. R. China 518055 1.3 Laboratory Condition Ambient Temperature 20°C to 25°C Ambient Relative Humidity 45% to 55% Ambient Pressure 100 kPa to 102 kPa Report No.: BL-EC2090870-402 5 / 22 1.4 Announce (1) The test …

Text truncated - open the document above for the full version.

Annex No.: BL-EC2090870-AE 1 / 3 ANNEX B TEST SETUP PHOTOS B.1 Radiated Emission Below 30MHz 30MHz-1GHz Annex No.: BL-EC2090870-AE 2 / 3 Close-up Photo ow 1 Annex No.: BL-EC2090870-AE 3 / 3 B.2 Conducted Emissions Test Photo 1 Por Test Photo 2