2AXQL-RUKO001Bluetooth module

1 Technical specification document Shenzhen Ruike Innovation Technology Co., Ltd. F11GIM2 RemoteID Module Datasheet DoNo.：F11GIM2 Version：V0.2 Revision Description Version Data Description V0.1 2023-08-04 Frist version V0.2 2024-07-08 Update V1.4.1 Hardware 2 1. Introduction 2. Features Based on BLE 5.3 SOC Size：24x14x1mm Weight：0.8g Max Transmission Distance：150m（unobstructed, free of interference） Supply current：< 4.0mA @ 5V (Idle state) The F11GIM2 series module is a remote ID module single board solutiondesignedby Shenzhen Coolle Chaowan Technology Co., Ltd. for drones that meets the F3411-22a specification. Based on BLE 5.3 SOC, it has the 3 3. Specifications Parameter Value Max transmission distance 150m Message interval 10ms Supply voltage 3.6-5.5 V Power TBD Operatingtemperature range -30~70 °C （ Theoretical data, specific to actual environment ） Storage temperature range -40~85 °C（ Theoretical data, specific to actual environment ） Size 24 x 13.1x 1 mm Weight 0.9 g Communication interface UART：115200 4. Mechanical specifications Size： 24.0 * 13.1 * 1.0 mm 4 5. Pin allocation Pin Name Description 1 RX UART receive line 2 TX UART transmit line 3 GND Ground connect 5 4 VCC Power supply 5V FCC Warning Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules FCC Part 15.247 2.3 Specific operational use conditions This transmitter/module and its antenna(s) must not be co-located or operating in conjunction with any transmitter. This information also extends to the host manufacturer’s instruction manual. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs It is “not applicable” as trace antenna which is not used on the module. 2.6 RF exposure considerations This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The host product manufacturer would provide the above information to end users in their end-product manuals. 2.7 Antennas PCB Antenna; 2.1dBi; 2.402 GHz～2.480GHz 2.8 Label and compliance information The end product must carry a physical label or shall use e-labeling followed KDB784748D01 and KDB 784748 stating “Contains Transmitter Module FCC ID:2AXQL-RUKO001”. 6 2.9 Information on test modes and additional testing requirements For more information on testing, please contact the manufacturer. 2.10 Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity. FCC Statements (OEM) Integrator has to assure compliance of the entire end-product incl. the integrated RF Module. For 15 B (§15.107 and if applicable §15.109) compliance, the host manufacturer is required to show compliance with 15 while the module is installed and operating. Furthermore the module should be transmitting and the evaluation should confirm that the module's intentional emissions (15C) are compliant (fundamental / out-of-band). Finally the integrator has to apply the appropriate equipment authorization (e.g. Verification) for the new host device per definition in §15.101. Integrator is reminded to assure that these installation instructions will not be made available to the end-user of the final host device. The final host device, into which this RF Module is integrated has to be labeled with an auxiliary label stating the FCC ID of the RF Module, such as "Contains FCC ID:2AXQL-RUKO001". This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The Integrator will be responsible to satisfy SAR/ RF Exposure requirements, when the module integrated into the host device. Module statement The single-modular transmitter is a self-contained, physically delineated, component for which compliance can be demonstrated independent of the host operating conditions, and 7 which complies with all eight requirements of § 15.212(a)(1) as summarized below. 1) The radio elements have the radio frequency circuitry shielded. 2) The module has buffered modulation/data inputs to ensure that the device will complywith Part 15 requirements with any type of input signal. 3) The module contains power supply regulation on the module. 4) The module contains a permanently attached antenna. 5) The module demonstrates compliance in a stand-alone configuration. 6) The module is labeled with its permanently affixed FCC ID label. 7) The module complies with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. 8) The module complies with RF exposure requirements. NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, t…

Text truncated - open the document above for the full version.

Shenzhen Ruike Innovation Technology Co., Ltd. Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jun. 25, 2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2AXQL-RUKO001 FRN: 0030041628 [Shenzhen Ruike Innovation Technology Co., Ltd.] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, (Applicant signature) (DAZHONG LUO)

Shenzhen Ruike Innovation Technology Co., Ltd. Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jun. 25, 2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2AXQL-RUKO001 FRN: 0030041628 [Shenzhen Ruike Innovation Technology Co., Ltd.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, (Applicant signature) (DAZHONG LUO)

Shenzhen Ruike Innovation Technology Co., Ltd. Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Product Similarity Declaration Product name: Bluetooth module Model name: F11GIM2, F11PRO, F11PRO 2, F11PRO 3, F11MINI-3D, F11MINI2- 3D, F11MINI3-3D, F11PRO 3D, F11PRO 2-3D, F11PRO 3-3D, F11GIM, F11GIM3, F11GIM2-3D, F11GIM2-4D, F11GIM3-3D, F11, U11S, U11PRO, U11PRO 2, U11PRO 3, U11PRO 2-3D, U11PRO 3-3D FCC ID: 2AXQL-RUKO001 We (Shenzhen Ruike Innovation Technology Co., Ltd.) hereby state that all the models are electrical identical including the same software parameter and hardware design, same mechanical structure and design, the only difference is the model name. Signature: Contact person: DAZHONG LUO

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Shenzhen Ruike Innovation Technology Co., Ltd. Address: Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Product Name: Bluetooth module Model Number: F11GIM2, F11PRO, F11PRO 2, F11PRO 3, F11MINI-3D, F11MINI2-3D, F11MINI3-3D, F11PRO 3D, F11PRO 2-3D, F11PRO 3-3D, F11GIM, F11GIM3, F11GIM2-3D, F11GIM2-4D, F11GIM3-3D, F11, U11S, U11PRO, U11PRO 2, U11PRO 3, U11PRO 2-3D, U11PRO 3-3D FCC Identifier: 2AXQL-RUKO001 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: DAZHONG LUO Date: Mar.20, 2024 Title: Manager Signature of applicant:

Shenzhen Ruike Innovation Technology Co., Ltd. Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jun. 25, 2024 Subject; Request for Confidentiality FCC ID: 2AXQL-RUKO001 FRN: 0030041628 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely Contact person: DAZHONG LUO

Shenzhen Ruike Innovation Technology Co., Ltd. Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China RE FCC ID: 2AXQL-RUKO001 To the certification reviewer: We are hereby applying for [full] modular approval of the above-referenced FCC ID, based on compliance with [all] of the criteria as detailed below. Sincerely, [DAZHONG LUO] [General Manager] Part 15 Unlicensed Single Modular Transmitter Approval Justification per 15.212 Requirement per 15.212 reference (i) The radio elements of the modular transmitter must have their own RF shielding. Shielding is provided by a metal cover over the circuitry. (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided. All modulation and data inputs are buffered by circuitry on the transmitter chip. (iii) The modular transmitter must have its own power supply regulation. Power supply regulation is provided by circuitry on the transmitter chip. (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b) and 15.204(c). The antenna is fixed. (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 parameters. Testing was performed in a stand-alone configuration as shown in the test setup photos. (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. The modular was labeled with its own FCC ID. The outside of device in to which the module is installed will labeled Contains TX FCC ID: 2AXQL-RUKO001, Please refer to User Manual. Shenzhen Ruike Innovation Technology Co., Ltd. Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The modular is comply with all applicable FCC rules. Any modifications, not expressly approved by the manufacturer could void the authority to operate in these regions. (viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. This module operates under Part 15. 247 which is exempt from RF exposure evaluation owing to the very low operating power.

Report No.: AGC15705240435AP02 Page 1 of 3 EXTERNAL PHOTOS TOP VIEW OF EUT BOTTOM VIEW OF EUT Report No.: AGC15705240435AP02 Page 2 of 3 FRONT VIEW OF EUT BACK VIEW OF EUT Report No.: AGC15705240435AP02 Page 3 of 3 LEFT VIEW OF EUT RIGHT VIEW OF EUT ****************************************End of Report*************************************

FCC ID Label Location 3mm&12mm FCC ID: 2AXQL-RUKO001

Report No.: AGC15705240435AP02 Page 1 of 1 INTERNAL PHOTOS INTERNAL VIEW OF EUT (FIGURE 1) ****************************************End of Report************************************* BT Antenna

Page 1 of 10 RF Exposure Report Report No.: AGC15705240435FH01 FCC ID : 2AXQL-RUKO001 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Bluetooth module BRAND NAME : N/A MODEL NAME : F11GIM2, F11PRO, F11PRO 2, F11PRO 3, F11MINI-3D, F11MINI2-3D, F11MINI3-3D, F11PRO 3D, F11PRO 2-3D, F11PRO 3-3D, F11GIM, F11GIM3, F11GIM2-3D, F11GIM2-4D, F11GIM3-3D, F11, U11S, U11PRO, U11PRO 2, U11PRO 3, U11PRO 2-3D, U11PRO 3-3D APPLICANT : Shenzhen Ruike Innovation Technology Co., Ltd. DATE OF ISSUE : May 31, 2024 STANDARD(S) : FCC KDB 447498 D01 V06 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC15705240435FH01 Page 2 of 10 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / May 31, 2024 Valid Initial Release Report No.: AGC15705240435FH01 Page 3 of 10 Table of Contents 1. General Information ........................................................................................................................................ 4 2. Product Information ........................................................................................................................................ 5 2.1 Product Technical Description ................................................................................................................... 5 3. Test Environment ............................................................................................................................................ 6 3.1 Address Of The Test Laboratory ............................................................................................................... 6 3.2 Test Facility ................................................................................................................................................ 6 3.3 Environmental Conditions ......................................................................................................................... 7 4. Portable Device Evaluation Method and Limit ............................................................................................. 8 5. Mobile Device Evaluation Method and Limit ................................................................................................ 9 6. Measurement Results ................................................................................................................................... 10 7. Measurement Evaluation .............................................................................................................................. 10 Report No.: AGC15705240435FH01 Page 4 of 10 1. General Information Applicant Shenzhen Ruike Innovation Technology Co., Ltd. Address Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Manufacturer Shenzhen Ruike Innovation Technology Co., Ltd. Address Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Factory Shenzhen Ruike Innovation Technology Co., Ltd. Address Unit1 701, Rufeng Building, 573 Bulong Rd, Bantian Maantang community, Longgang district, Shenzhen, China Product Designation Bluetooth module Brand Name N/A Test Model F11GIM2 Series Model(s) F11PRO, F11PRO 2, F11PRO 3,F11MINI-3D, F11MINI2-3D, F11MINI3-3D, F11PRO 3D, F11PRO 2-3D, F11PRO 3-3D, F11GIM, F11GIM3, F11GIM2-3D, F11GIM2-4D, F11GIM3-3D, F11, U11S, U11PRO, U11PRO 2, U11PRO 3, U11PRO 2-3D, U11PRO 3-3D Difference Description All the same except for the model names. Date of receipt of test item Apr. 15, 2024 Date of Test Apr. 15, 2024~May 31, 2024 Deviation from Standard No any deviation from the test method Condition of Test Sample Normal Test Result Pass Test Report Form No AGCER-FCC-RF Exposure-V1 Note: The test results of this report relate only to the tested sample identified in this report. Prepared By Cool Cheng (Project Engineer) May 31, 2024 Reviewed By Calvin Liu (Reviewer) May 31, 2024 Approved By Max Zhang (Authorized Officer) May 31, 2024 Report No.: AGC15705240435FH01 Page 5 of 10 2. Product Information 2.1 Product Technical Description Frequency Band (Operating) Bluetooth: 2.402GHz ~ 2.480GHz Other: Hardware Version V1.0 Software Version V1.0 Modulation Type BLE GFSK 1Mbps GFSK 2Mbps Device Category Portable (<20cm separation) Mobile (>20cm separation) Others: Antenna Diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Antenna Designation PCB Antenna Antenna Gain 2.1dBi Minimum Assessment Distance 5mm Evaluation Applied MPE Evaluation SAR Evaluation Report No.: AGC15705240435FH01 Page 6 of 10 3. Test Environment 3.1 Address Of The Test Laboratory Laboratory: Attestation of Global Compliance (Shenzhen) Co., Ltd. Address: 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China 3.2 Test Facility The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5488 Attestation of Global Compliance (Shenzhen) Co., Ltd. has been assessed and proved to follow CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories.) A2LA-Lab Cert. No.: 5054.02 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to follow ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. FCC-Registration No.: 975832 Attestation of Global Compliance (Shenzhen) Co., Ltd. EMC Laboratory has been registered and fully described in a report filed with the FCC (Federal Communications Commission). The acceptance letter from the FCC is maintained in our files with Registration 975832. IC-Registration No.: 24842(CAB identifi…

Text truncated - open the document above for the full version.

PCB Antenna for BLE Chips of WCH 1、Dimension of Antenna 2、Features  Dimension: 5.6*12.3mm  Terminal impedance: 50 ohm  Max Gain: 2.1dBi  RF Frequency: 2.4GHz 3、S parameter Working bandwidth: 157MHz S11：[email protected] 4、Gain and Radiation pattern Max gain @2.4GHz: 2.08dBi E plane： H plane： Max Gain @2.44GHz: 2.1dBi E plane： H plane： Max Gain @2.48GHz: 2.04dBi E plane： H plane：

Page 1 of 52 FCC Test Report Report No.: AGC15705240435FR01 FCC ID : 2AXQL-RUKO001 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Bluetooth module BRAND NAME : N/A MODEL NAME : F11GIM2, F11PRO, F11PRO 2, F11PRO 3, F11MINI-3D, F11MINI2-3D, F11MINI3-3D, F11PRO 3D, F11PRO 2-3D, F11PRO 3-3D, F11GIM, F11GIM3, F11GIM2-3D, F11GIM2-4D, F11GIM3-3D, F11, U11S, U11PRO, U11PRO 2, U11PRO 3, U11PRO 2-3D, U11PRO 3-3D APPLICANT : Shenzhen Ruike Innovation Technology Co., Ltd. DATE OF ISSUE : May 31, 2024 STANDARD(S) : FCC Part 15 Subpart C §15.247 REPORT VERSION : V1.0 Attestation Of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC15705240435FR01 Page 2 of 52 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / May 31, 2024 Valid Initial Release Report No.: AGC15705240435FR01 Page 3 of 52 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ..................................................................................................................... 6 2.2 Test Frequency List ..................................................................................................................................... 6 2.3 Related Submittal(S) / Grant (S) ................................................................................................................. 7 2.4 Test Methodology......................................................................................................................................... 7 2.5 Special Accessories ..................................................................................................................................... 7 2.6 Equipment Modifications ............................................................................................................................. 7 2.7 Antenna Requirement .................................................................................................................................. 7 3. Test Environment ............................................................................................................................................ 8 3.1 Address of the Test Laboratory .................................................................................................................... 8 3.2 Test Facility .................................................................................................................................................. 8 3.3 Environmental Conditions ........................................................................................................................... 9 3.4 Measurement Uncertainty ........................................................................................................................... 9 3.5 List of Equipment Use ............................................................................................................................... 10 4.System Test Configuration ............................................................................................................................ 12 4.1 EUT Configuration ..................................................................................................................................... 12 4.2 EUT Exercise ............................................................................................................................................. 12 4.3 Configuration of Tested System ................................................................................................................ 12 4.4 Equipment Used In Tested System ........................................................................................................... 12 4.5 Summary of Test Results ........................................................................................................................... 13 5. Description of Test Modes ........................................................................................................................... 14 6. Duty Cycle Measurement ............................................................................................................................. 15 7. RF Output Power Measurement .................................................................................................................. 16 7.1 Provisions Applicable ................................................................................................................................. 16 7.2 Measurement Procedure ........................................................................................................................... 16 7.3 Measurement Setup (Block Diagram of Configuration) ............................................................................ 16 7.4 Measurement Result ................................................................................................................................. 17 8. 6dB Bandwidth Measurement ...................................................................................................................... 20 8.1 Provisions Applicable ................................................................................................................................. 20 8.2 Measurement Procedure ........................................................................................................................... 20 8.3 Measurement Setup (Block Diagram of Configuration) ............................................................................ 20 8.4 Measurement Results ................................................................................................................................ 21 9. Power Spectral Dens…

Text truncated - open the document above for the full version.

Report No.: AGC15705240435AP01 Page 1 of 2 TEST SETUP PHOTOS RADIATED EMISSION TEST SETUP BELOW 1GHz RADIATED EMISSION TEST SETUP ABOVE 1GHz Report No.: AGC15705240435AP01 Page 2 of 2 AC POWER LINE CONDUCTED TEST SETUP RF CONDUCTED TEST SETUP ****************************************End of Report*************************************