2AY2B-BTGPTBluMorpho

BlūSeries Transmitter Operations Manual Page of 18 IC: 32683-BTGPT FCC ID: 2AY2B-BTGPT Model: BTGPT Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s) and Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Page of 28 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC & IC Radiation Exposure Statement: This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Déclaration d’IC sur l’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux radiations définies par le Canada pour des environnements non contrôlés. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre l’antenne et votre corps. Page of 38 Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne ou un autre émetteur. Page of 48 BlūSeries Transmitter Operation Manual Theory of Operation Your BlūSeries Transmitter is a digital radio transmitter that features a unique identifier. No two tags will ever have the same identifier, allowing multiple projects and species to be tracked simultaneously, worldwide, without overlap in transmitter codes. Your BlūSeries Transmitter can also be received by a growing distributed network of autonomous sensors collecting data from all wildlife transmitters, around the world! Your BlūSeries Transmitter is designed to be received by a variety of methods: CTT Internet of Wildlife devices: ● CTT SensorStation base station with BlūSeries Receiver ● CTT Sidekick portable receiver products ● The forthcoming (Q4 2024) Terra, a direct-to-consumer citizen science product. And a global collaborative scientific platform: ● The Motus Wildlife Tracking System (hereafter Motus Network), operated by Birds Canada ● When your PowerTag signal is received on a CTT Internet of Wildlife device, or via the Motus Network, the exact date, time, unique identifier, and signal strength will be recorded. To learn more about our products, and future products, visit: www.CellTrackTech.com. Attachment BlūSeries Transmitters are deployment-ready as glue-on tags, or can be mounted to a variety of DIY harness or other mounting solutions you can think of. If you would like to discuss options for attachment, don’t hesitate to reach out to our Wildlife Application Specialists at Cellular Tracking Technologies via [email protected]. Page of 58 While attachments can vary, some key points to remember are: Never trim the antenna, as its length is both dependent on top performance as well as FCC certification of the device. When possible, keep the body of the animal away from the antenna, as this will affect the range and efficiency of the antenna. Range will vary depending on the height of the animal. For example, a bird or butterfly in flight will have much further line-of- sight than an animal crawling on the ground. Water dwelling animals will need to have the antenna above the surface of the water in order to operate most effectively. Page of 68 Contacting Us If you have any questions you can contact us in the following ways: Email: [email protected] Phone: +1 609 889 0305 Mail: Cellular Tracking Technologies 1293 Hornet Rd. Suite #1 Rio Grande, NJ 08242 Page of 78 Notes My Tag IDs Page of 88

发件人：[email protected] 收件人：Chen, June-YJ (Guangzhou) 主题：[EXTERNAL] Response to Inquiry to FCC (Tracking Number 662120) 日期：2024 年 8 月 20 日 1:41:10 *** WARNING: this message is from an EXTERNAL SENDER. Please be cautious, particularly with links and attachments. *** Inquiry on 08/18/2024 : Inquiry: Good day! The certified product (as attachment) is too small to put on the FCC ID number and related statement. According to the below rules, please approve to put the FCC ID number and related statement on the user manual instead of the product. Thank you! CFR Title 47 Part 2 §2.925 Identification of equipment. (f) The FCC Identifier including the term “FCC ID” shall be in a size of type large enough to be readily legible, consistent with the dimensions of the equipment and its label. However, the type size for the FCC Identifier is not required to be larger than eight-point. If a device is so small that it is impractical to label it with the FCC Identifier in a font that is four-point or larger, and the device does not have a display that can show electronic labeling, then the FCC Identifier shall be placed in the user manual and must also either be placed on the device packaging or on a removable label attached to the device. CFR Title 47 Part 15 §15.19 Labeling requirements. (5) When the device is so small or for such use that it is impracticable to label it with the statement specified under paragraph (a) of this section in a font that is four-point or larger, and the device does not have a display that can show electronic labeling, then the information required by this paragraph shall be placed in the user manual and must also either be placed on the device packaging or on a removable label attached to the device. FCC response on 08/19/2024 The rules allow you to [put the FCC ID and statement in the manual. Attachment Details: Do not reply to this message. Please select the Reply to an Inquiry Response link from the OET Inquiry System to add any additional information pertaining to this inquiry.

SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a)in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b)in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1)labeling the equipment with the exact FCC ID as specified in this application, (2)compliance statement labeling pursuant to the applicable rules, (3)compliance of the equipment with the applicable technical rules, c)if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d)in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e)in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1)the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2)the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3)the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f)neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g)the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List Applicant Legal Business NameCellular Tracking Technologies LLC Address1293 Hornet Road Suite #1, Rio Grande, New Jersey, 08242, United States FRN0026021097 Grantee Code2AY2B FCC ID2AY2B-BTGPT Authorized Contact NameCasey Halverson Contact [email protected] Contact Phone6098890305 Cellular Tracking Technologies LLC (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Cellular Tracking Technologies LLC (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date: Date: 2024/7/3 Print Name:Casey Halverson Title:COO QSF27-14-04 Rev 1.1 Jan 17, 2024 Page of Original Issue: Jan. 4, 2021 12 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database QSF27-14-04 Rev 1.1 Jan 17, 2024 Page of Original Issue: Jan. 4, 2021 22

UNITED STATES DESIGNATED AGENT LETTER Date: 2024/7/3 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicable Equipment: FCC ID: 2AY2B-BTGPT ATTN: Director of Certification: We, Cellular Tracking Technologies LLC understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, Cellular Tracking Technologies LLC acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. ApplicantU.S. designated agent Company Name: Cellular Tracking Technologies LLC Company Name: Cellular Tracking Technologies LLC FRN:0026021097FRN:0026021097 Grantee Code:2AY2B Contact Name:Casey HalversonContact NameCasey Halverson Address:1293 Hornet Road Suite #1Address:1293 Hornet Road Suite #1 City/Province/ Zip: Rio Grande, New Jersey, 08242City/Province/ Zip: Rio Grande, New Jersey, 08242 Telephone:6098890305Telephone:6098890305 Fax:6095514160Fax:6095514160 Email:casey.halverson@celltracktech. com Email:casey.halverson@celltracktech. com Applicant U.S. designated agent Name (Printed): Casey HalversonName (Printed): Casey Halverson Title: COOTitle: COO Signature: Signature:

Cellular Tracking Technologies LLC Authority letter FCC Date: 2024/7/3 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: 2AY2B-BTGPT To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch and Bonnie Liao in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Guangzhou branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with applicant company FCC. This authorization is valid until further written notice from the applicant. Name (Printed): Casey Halverson Title: COO Signature: On behalf of Company: Cellular Tracking Technologies LLC

Cellular Tracking Technologies LLC Confidential letter FCC To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Cellular Tracking Technologies LLC 1293 Hornet Road Suite #1, Rio Grande, New Jersey, 08242, United States Regarding: Confidentiality Request regarding application for FCC ID: 2AY2B-BTGPT LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Name (Printed): Casey Halverson Title: COO Signature: On behalf of Company: Cellular Tracking Technologies LLC

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 1 of 4 Appendix - External Photos for GZCR2404000380AT Test Model No.: BTGPT SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 2 of 4 EUT Constructional Details (EUT Photos) SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-02 Rev 1.1 Page: 4 of 4 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 1 of 2 Appendix - Internal Photos for GZCR2404000380AT Test Model No.: BTGPT SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-ARF-03 Rev 1.1 Page: 2 of 2 EUT Constructional Details (EUT Photos) - End of the Appendix - RF ANT

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240400038002 Page: 1 of 9 FCC ID: 2AY2B-BTGPT Ricky Liu Manager RF EXPOSURE EVALUATION REPORT Application No.: GZCR2404000380AT Applicant:Cellular Tracking Technologies LLC Address of Applicant:1293 Hornet Road, Suite #1, Rio Grande, New Jersey 08242, United States Manufacturer:Cellular Tracking Technologies LLC Address of Manufacturer:1293 Hornet Road, Suite #1, Rio Grande, New Jersey 08242, United States Factory:Cellular Tracking Technologies LLC Address of Factory:1293 Hornet Road, Suite #1, Rio Grande, New Jersey 08242, United States Product Name:BluMorpho Model No.: BTGPT Trade Mark:BluMorpho Standard(s) : 47 CFR Part 1.1310 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2024-04-18 Date of Evaluation: 2024-06-06 Date of Issue: 2024-06-11 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240400038002 Page: 2 of 9 Revision Record VersionReport No.DateRemark 01GZCR2404000380022024-06-11Original Authorized for issue by: Damon Guan/Project Engineer Vico Cui/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240400038002 Page: 3 of 9 2Evaluation Summary ItemStandardMethodRequirementResult RF Exposure KDB447498D01 General RF Exposure Guidance v06 KDB447498D01 General RF Exposure Guidance v06 47 CFR Part 1.310Pass Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240400038002 Page: 4 of 9 3Contents Page 1Cover Page...............................................................................................................................................1 2Evaluation Summary................................................................................................................................3 3Contents....................................................................................................................................................4 4General Information.................................................................................................................................5 4.1Details of E.U.T.................................................................................................................................5 4.2Evaluating Location...........................................................................................................................5 4.3Facility...............................................................................................................................................6 4.4Deviation from Standards..................................................................................................................6 4.5Abnormalities from Standard Conditions...........................................................................................6 5Technical Requirements Specification..................................................................................................7 5.1General Description of Applied Standards........................................................................................7 5.2RF Exposure Evaluation....................................................................................................................7 5.2.1Limit & Test Method......................................................................................................................7 5.2.2Conclusion....................................................................................................................................8 6EUT Constructional Details (EUT Photos).............................................................................................9 SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240400038002 Page: 5 of 9 4General Information 4.1Details of E.U.T. Power supply:Powered by 3V battery refer to section 4.2. Cable(s):DC input cable Operation Frequency: 37 advertising channel: 2402MHz; 38 advertising channel: 2426MHz; 39 advertising channel: 2480MHz Modulation Type:GFSK Number of Channels:3 Antenna Gain:-0.30 dBi according to the antenna test report SZOA2407000161AT01 Remark: The information in this section is provided by the applicant or manufacturer, SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. 4.2Evaluating Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Guangzhou Branch EMC Laboratory, No.198, Kezhu Road, Science City, Economic & Technological Development Area, Guangzhou, Guangdong, China 510663 Tel: +86 20 82155555 No tests were sub-contracted. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-03 Rev 1.1 Report No.: GZCR240400038002 Page: 6 of 9 4.3Facility The facility is recognized, certified, or accredited by the following organizations: ● ACMA SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory can also perform testing for the Australian/New Zealand Regulatory Compliance Mark (RCM). ● SGS UK(Certificate No.: 32), SGS-TUV SAARLAND and SGS-FIMKO Have approved SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory as a supplier of EMC TESTING SERVICES and SAFETY TESTING SERVICES. ● FCC Recognized Accredited Test Firm(Registration No.: 486818) SGS-CSTC Standards Technical Services Co., Ltd., EMC Laboratory has been accredited and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Designation Number: CN5016, Test Firm Registration Number: 486818.…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240400038001 Page: 1 of 47 FCC ID: 2AY2B-BTGPT Ricky Liu Manager TEST REPORT Application No.: GZCR2404000380AT Applicant: Cellular Tracking Technologies LLC Address of Applicant: 1293 Hornet Road, Suite #1, Rio Grande, New Jersey 08242, United States Manufacturer: Cellular Tracking Technologies LLC Address of Manufacturer: 1293 Hornet Road, Suite #1, Rio Grande, New Jersey 08242, United States Factory: Cellular Tracking Technologies LLC Address of Factory: 1293 Hornet Road, Suite #1, Rio Grande, New Jersey 08242, United States Product Name: BluMorpho Model No.: BTGPT Trade Mark: BluMorpho Standard(s) : 47 CFR Part 15, Subpart C 15.247 Date of Receipt: 2024-04-18 Date of Test: 2024-05-10 to 2024-06-04 Date of Issue: 2024-06-11 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240400038001 Page: 2 of 47 Revision Record Version Report No. Date Remark 01 GZCR240400038001 2024-06-11 Original Authorized for issue by: Damon Guan/Project Engineer Vico Cui/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240400038001 Page: 3 of 47 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.247 N/A 47 CFR Part 15, Subpart C 15.203 & 15.247(b)(4) Pass Radio Spectrum Matter Part Item Standard Method Requirement Result Radiated Emissions which fall in the restricted bands 47 CFR Part 15, Subpart C 15.247 ANSI C63.10 (2013) Section 11.12 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass ** Radiated Spurious Emissions Below 1GHz ANSI C63.10 (2013) Section 6.4,6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Spurious Emissions Above 1GHz ANSI C63.10 (2013) Section 6.6 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass ** Conducted Peak Output Power ANSI C63.10 (2013) Section 11.9.1 47 CFR Part 15, Subpart C 15.247(b)(3) Pass Minimum 6dB Bandwidth ANSI C63.10 (2013) Section 11.8.1 47 CFR Part 15, Subpart C 15.247a(2) Pass Power Spectrum Density ANSI C63.10 (2013) Section 11.10.2 47 CFR Part 15, Subpart C 15.247(e) Pass Conducted Band Edges Measurement ANSI C63.10 (2013) Section 11.13.3.2 47 CFR Part 15, Subpart C 15.247(d) Pass Conducted Spurious Emissions ANSI C63.10 (2013) Section 11.11 47 CFR Part 15, Subpart C 15.247(d) Pass Note: E.U.T./EUT means Equipment Under Test. Pass means the test result passed the test standard requirement, please find the detailed decision rule in the report relative section. **: The EUT passed Radiated Emissions which fall in the restricted bands and Radiated Spurious Emissions Above 1GHz test after modification. SGS-CSTC Standards Technical Services Co., Ltd. Guangzhou Branch EMC-TRF-01 Rev 1.1 Report No.: GZCR240400038001 Page: 4 of 47 3 Contents Page 1 Cover Page .............................................................................................................................................. 1 2 Test Summary ......................................................................................................................................... 3 3 Contents .................................................................................................................................................. 4 4 General Information................................................................................................................................ 6 4.1 Details of E.U.T. ............................................................................................................................... 6 4.2 Description of Support Units ............................................................................................................. 6 4.3 Measurement Uncertainty ................................................................................................................ 6 4.4 Test Location.................................................................................................................................... 7 4.5 Test Facility ...................................................................................................................................... 7 4.6 Deviation from Standards ................................................................................................................. 7 4.7 Abnormalities from Standard Conditions .......................................................................................... 7 5 Equipment List........................................................................................................................................ 8 6 Radio Spectrum Technical Requirement ............................................................................................ 10 6.1 Antenna Requirement .................................................................................................................... 10 6.1.1 Test Requirement: ..................................................................................................................... 10 6.1.2 Conclusion ................................................................................................................................. 10 7 Radio Spectrum Matter Test Results................................................................................................... 11 7.1 Radiated Emissions which fall in the restricted bands .................................................................... 11 7.1.1 E.U.T. Operation ........................................................................................................................ 11 7.1.2 Test Mode Description ............................................................................................................... 11 7.1.3 Test Setup Diagram .....................…

Text truncated - open the document above for the full version.

` SGS-CSTC Standards Technical Services Co., Ltd Shenzhen Branch Report No.: SZOA2407000161AT01 Rev.:01 Page: 1 of 18 Report Template No./Rev: SZWI-TRF-OA006/ v02 ANTENNA PASSIVE TEST REPORT Application No.SZOA2407000161AT ApplicantCellular Tracking Technologies LLC ManufacturerCellular Tracking Technologies LLC Product NameBluMorpho Model No.BTGPT StandardsANSI/IEEE Std 149-2021 Date Initial Sample(s) ReceivedJuly 30, 2024 Testing Start DateJuly 30, 2024 Testing Finish DateJuly 30, 2024 Report Issue DateAugust 12, 2024 *In the configuration tested, the EUT detailed in this report complied with the standards specified above. Prepared by: Yuanyu Luo/ Test Engineer Approved by: Ervin Li/ Technical Manager ` SGS-CSTC Standards Technical Services Co., Ltd Shenzhen Branch Report No.: SZOA2407000161AT01 Rev.:01 Page: 2 of 18 Report Template No./Rev: SZWI-TRF-OA006/ v02 Revision History RevisionIssue DateDescription 01August 12, 2024Initial creation of report ` SGS-CSTC Standards Technical Services Co., Ltd Shenzhen Branch Report No.: SZOA2407000161AT01 Rev.:01 Page: 3 of 18 Report Template No./Rev: SZWI-TRF-OA006/ v02 TABLE OF CONTENTS 1GENERAL INFORMATION....................................................................................................4 1.1Testing Laboratory..............................................................................................................................4 1.2Details of Applicant.............................................................................................................................4 1.3Details of Manufacturer.…

Text truncated - open the document above for the full version.