2AYCQ-SV4ACCRFIDRFID Keypad Reader

4. Functions Table Sheet Read Card External LED Control External Buzzer Control Wiegand Data Output Packing List Name The LED light will turn into Green, and the buzzer sounds a beep, at the meantime, the reader outputs the Wiegand signal When the input voltage for LED is low, the LED will turn into Green When the input voltage for Buzzer is low, the Buzzer will sounds Wiegand 26-44, 56, 58bits available upon request, factory default setting is Wiegand 26bits for EM version, 34bits for Mifare version. Quantity 1 1 1 FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used exposure condition without restriction. IC warning - English: This device complies with Industry Canada licence-exempt RSS standard{s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. - French: L'emetteur/recepteur exempt de licence contenu dans le present appareil est conforme aux CNR d'lnnovation, Sciences et Developpement economique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radio创ectriquesubi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement. The device can be used exposure condition without restriction. Ce t équipement respecte les limites d'exposition aux rayonnements IC RSS-102 établies pour un environnement non contrôlé. L'appareil a été évalué pour répondre aux exigences générales en matière d'exposition RF. Il peut être utilisé dans des conditions d'exposition sans restriction.

GEM ONE NV 2026/08/24 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(i) request for FCC ID: 2AYCQ-SV4ACCRFID [GEM ONE NV] certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the equipment does not utilize cyber-security or anti-virus software from Kaspersky Lab, Inc, or any of its successors and assignees, which is also on the “covered list”. Sincerely, Client’s signature: Client’s name / title : Sander Loosveld/Chief Product Officer GEM ONE NV 2026/08/24 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: Attestation Statements Part 2.911(d)(5)(ii) request for FCC ID: 2AYCQ- SV4ACCRFID [GEM ONE NV] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Client’s signature: Client’s name / title : Sander Loosveld/Chief Product Officer

U.S. Agent Designation for Service of Process TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Baihetian Innovative Solutions Address: 6837 Chase Rd Dearborn,Ml 48126 FRN: 0033401605 Contact Name: Kenneth Young Tel.: 313-395-3113 Email: [email protected] This letter is to confirm that we (Baihetian Innovative Solutions) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: Signed by (Printed Name/Title): The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: GEM ONE NV Grantee Code: 2AYCQ FCC ID: 2AYCQ-SV4ACCRFID Contact Name: Sander Loosveld Street Address: Brabantstraat 15, 8790, Waregem, Belgium Telephone No: +32 (0) 56 43 64 00 Email: [email protected] FRN: 0030248652 Applicant Signature: Date: 2026/08/24 Signed by (Printed Name/Title): Sander Loosveld / Chief Product Officer GEM ONE NV Sander Loosveld Aug 25, 2026 Aug 2026 Kenneth Young/Manager

Declaration on model difference We the undersigned hereby confirm that any of our production units bearing the following model numbers are identical in circuitry and electrical, mechanical and physical construction; The difference lies in the model name. Production name Trade name Model no. RFID Reader N/A SAP-V4-ACC-RFID, SK2-RX Confirmed by：GEM ONE NV Signature: Date: 2026/08/24 Name: Sander Loosveld Title: Chief Product Officer Company: GEM ONE NV

GEM ONE NV 2026/08/24 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR Product Name: RFID Reader FCCID: 2AYCQ-SV4ACCRFID Model(s): SAP-V4-ACC-RFID, SK2-RX To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the - Block Diagram - Schematics - Operational Description required to be submitted with this application be permanently withheld from public review. The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Please contact me if there is any information you may need. Sincerely, Client’s signature: Client’s name / title : Sander Loosveld/Chief Product Officer Contact information / address: Brabantstraat 15, 8790 Waregem Belgium

GEM ONE NV 2026/08/24 Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION Product Name: RFID Reader FCCID: 2AYCQ-SV4ACCRFID Model(s): SAP-V4-ACC-RFID, SK2-RX To Whom It May Concern: We, the undersigned, hereby authorize Shenzhen BCTC Technology Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Client’s signature: Client’s name / title : Sander Loosveld/Chief Product Officer Contact information / address: Brabantstraat 15, 8790 Waregem Belgium

External Photos

Size:20mm*15mm FCC ID: 2AYCQ-SV4ACCRFID IC: 33213-SV4ACCRFID Label location

Internal Photos 125KHz Antenna 13.56MHz Antenna

No.：BCTC/KJ-RF-ICT-001 Page 1 of 14 Edition：B.1 TEST REPORT Shenzhen BCTC Technology Co., Ltd. Report No.: BCTC2607316066-2E Applicant: GEM One NV Product Name: RFID Reader Test Model: SAP-V4-ACC-RFID Tested Date: 2026-07-23 to 2026-08-07 Issued Date: 2026-08-27 Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 2 of 14 Edition：B.1 FCC ID: 2AYCQ-SV4ACCRFID The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Technology Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: RFID Reader Trademark: N/A Model/Type reference: SAP-V4-ACC-RFID Prepared For: GEM One NV Address: Brabantstraat 15, 8790 Waregem Belgium Manufacturer: Secukey Technology Co.,Ltd. Address: Floor 5, Building 13, Longbi Industrial Park, Bantian Sub District, Longgang District, Shenzhen, China. Prepared By: Shenzhen BCTC Technology Co., Ltd. Address: Room 101M, Unit 1, Building1, Pengyuan, No.18, Lilang Road, Shanglilang, Nanwan Subdistrict, Longgang District, Shenzhen, Guangdong, China. Sample Received Date: 2026-07-22 Sample tested Date: 2026-07-23 to 2026-08-07 Report No.: BCTC2607316066-2E Test Standards: FCC CFR 47 part1, 1.1307(b), 1.1310 KDB 680106 D01 Wireless Power Transfer v04 Test Results: PASS Prepared by : Reviewer by : Approved by: Eric Yang Mike Zheng Sewen Guo Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 3 of 14 Edition：B.1 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Product Information ............................................................................................... 5 2.1 Product Information ............................................................................................... 5 2.2 Test Setup Configuration ...................................................................................... 5 2.3 Support Equipment ............................................................................................... 6 2.4 Test Mode ............................................................................................................. 6 3. Test Facility And Test Instrument Used ................................................................. 7 3.1 Test Facility ........................................................................................................... 7 3.2 Test Instrument Used ............................................................................................ 7 4. Method Of Measurement ....................................................................................... 8 4.1 Applicable Standard .............................................................................................. 8 4.2 Block Diagram Of Test Setup ................................................................................ 8 4.3 Limit ...................................................................................................................... 9 4.4 Test procedure ...................................................................................................... 9 4.5 E and H field Strength ......................................................................................... 10 5. Photographs Of Test Set-Up ............................................................................... 13 (Note: N/A Means Not Applicable) Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 4 of 14 Edition：B.1 1. Version Report No. Issue Date Description Approved BCTC2309647432-1E 2026-08-27 Original Valid Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 5 of 14 Edition：B.1 2. Product Information 2.1 Product Information Model/Type reference: SAP-V4-ACC-RFID Model differences: N/A Operation Frequency: 125KHz Type of Modulation: ASK Antenna installation: loop coil antenna Ratings: DC 12V 2.2 Test Setup Configuration See test photographs attached in EUT TEST SETUP PHOTOGRAPHS for the actual connections between Product and support equipment. Radiated Spurious Emission: E-1 EUT E-2 Battery Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 6 of 14 Edition：B.1 2.3 Support Equipment No. Device Type Brand Model Series No. Note E-2 Battery N/A 57069 N/A Auxiliary Notes: 1. All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2. Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 2.4 Test Mode Test Mode 1 TX Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 7 of 14 Edition：B.1 3. Test Facility And Test Instrument Used 3.1 Test Facility All measurement facilities used to collect the measurement data are located at Shenzhen BCTC Technology Co., Ltd. Address: Room 101M, Unit 1, Building1, Pengyuan, No.18, Lilang Road, Shanglilang, Nanwan Subdistrict, Longgang District, Shenzhen, Guangdong, China. The site and apparatus are constructed in conformance with the requirements of ANSI C63.4a-2017 and CISPR 16-1-1:2019 other equivalent standards. FCC Test Firm Registration Number: 754702 ANAB certificate registration number is: CN3479 3.2 Test Instrument Used Name of instrument Model Manufacturer Cal. Date Due Date Electro magnetic radiation tester SMP160 Wavecontrol 2026.05.12 2027.05.13 Report No.: BCTC2607316066-2E No.：BCTC/KJ-RF-ICT-001 Page 8 of 14 Edition：B.1 4. Method Of Measurement 4.1 Applicable Standard According to §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1093 RF exposure is calculated. According KDB680106 D01v04: RF Exposure Wireless Charging Apps v04. 4.2 Block Dia…

Text truncated - open the document above for the full version.

Antenna Specification Manufacturer: Secukey Technology Co.,Ltd. Address: Floor 5, Building 13, Longbi Industrial Park, Bantian Sub District, Longgang District, Shenzhen, China. Length * Width: 22.00mm *34.00mm. Thickness:1.95mm. Material: copper. Turns number: 107 Wire used length: 11.65m Wire diameter: 0.17mm Inside diameter:2.11mm All measurements were performed radiated and therefore additional antenna gain documentation is not required.

No.：BCTC/KJ-RF-ICT-001 Page 1 of 22 Edition：B.1 TEST REPORT Shenzhen BCTC Technology Co., Ltd. Report No.: BCTC2607316066E Applicant: GEM One NV Product Name: RFID Reader Test Model: SAP-V4-ACC-RFID Tested Date: 2026-07-23 to 2026-08-07 Issued Date: 2026-08-27 Report No.: BCTC2607316066E No.：BCTC/KJ-RF-ICT-001 Page 2 of 22 Edition：B.1 FCC ID: 2AYCQ-SV4ACCRFID The test report is effective only with both signature and specialized stamp.This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen BCTC Technology Co., Ltd, this report can’t be reproduced except in full.The tested sample(s) and the sample information are provided by the client. Product Name: RFID Reader Trademark: N/A Model/Type Reference: SAP-V4-ACC-RFID,SK2-RX Prepared For: GEM One NV Address: Brabantstraat 15, 8790 Waregem Belgium Manufacturer: Secukey Technology Co.,Ltd. Address: Floor 5, Building 13, Longbi Industrial Park, Bantian Sub District, Longgang District, Shenzhen, China. Prepared By: Shenzhen BCTC Technology Co., Ltd. Address: Room 101M, Unit 1, Building1, Pengyuan, No.18, Lilang Road, Shanglilang, Nanwan Subdistrict, Longgang District, Shenzhen, Guangdong, China. Sample Received Date: 2026-07-22 Sample Tested Date: 2026-07-23 to 2026-08-07 Report No.: BCTC2507151318-2E Test Standards: 47 CFR Part 15 Subpart C（clause 15.225） ANSI C63.10-2020 Test Results: PASS Remark: This is NFC-125K radio test report. Prepared by : Reviewer by : Approved by: Eric Yang Mike Zheng Sewen Guo Report No.: BCTC2607316066E No.：BCTC/KJ-RF-ICT-001 Page 3 of 22 Edition：B.1 Table Of Content Test Report Declaration Page 1. Version .................................................................................................................. 4 2. Test Summary ....................................................................................................... 5 3. Measurement Uncertainty ..................................................................................... 6 4. Product Information And Test Setup ..................................................................... 7 4.1 Product Information ............................................................................................... 7 4.2 Test Setup Configuration ...................................................................................... 8 4.3 Support Equipment ............................................................................................... 8 4.4 Channel List .......................................................................................................... 8 4.5 Test Mode ............................................................................................................. 8 5. Test Facility And Test Instrument Used ................................................................. 9 5.1 Test Facility ........................................................................................................... 9 5.2 Test Instrument Used ............................................................................................ 9 6. Conducted Emissions .......................................................................................... 11 6.1 Block Diagram Of Test Setup .............................................................................. 11 6.2 Limit .................................................................................................................... 11 6.3 Test Procedure ................................................................................................... 11 6.4 EUT operating Conditions ................................................................................... 11 7. Radiated Emissions ............................................................................................. 12 7.1 Block Diagram Of Test Setup .............................................................................. 12 7.2 Limit .................................................................................................................... 13 7.3 EUT Operating Conditions .................................................................................. 14 7.4 Test Result .......................................................................................................... 15 8. Bandwidth Test .................................................................................................... 18 8.1 Block Diagram Of Test Setup .............................................................................. 18 8.2 Test Procedure ................................................................................................... 18 8.3 EUT Operation Conditions .................................................................................. 18 8.4 Test Result .......................................................................................................... 19 9. Antenna Requirement ......................................................................................... 20 9.1 Standard Requirement ........................................................................................ 20 9.2 EUT Antenna ...................................................................................................... 20 10. EUT Test Setup Photographs.............................................................................. 21 (Note: N/A Means Not Applicable) Report No.: BCTC2607316066E No.：BCTC/KJ-RF-ICT-001 Page 4 of 22 Edition：B.1 1. Version Report No. Issue Date Description Approved BCTC2507386723-3E 2026-08-27 Original Valid Report No.: BCTC2607316066E No.：BCTC/KJ-RF-ICT-001 Page 5 of 22 Edition：B.1 2. Test Summary The Product has been tested according to the following specifications: No. Test Parameter Clause No Results 1 Conducted Emission 15.207 N/A 2 Radiated Spurious Emission Part 15.209(a), 15.225(d) PASS* 3 20dB Occupied Bandwidth 15.215 PASS* 4 Antenna Requirement 15.203 PASS NOTE1: N/A (Not Applicable) NOTE2:"*" indicates that the test result…

Text truncated - open the document above for the full version.

Radiated Measurement Photos